Rejuvenation of Bawari at various locations in Mandi Town Tehsil Sadar Distt Mandi HP

Amount

Cleaning of bawari by Grinding, washing, rubbing and polishing with polish of superior quality to stone with putty etc. includingcost of carriage of materials complete in all respect and to the entire satisfacton of the Engineer-in-Charge.

Demolition above G.L. upto floor two level i/c disposal of unservicable material with in 20 meters lead reinforcement cement concrete upto 15 cm. thickness in all leads and lifts.

Demolition of stone masonry above G.L. upto floor two level including stacking of servicable materials and disposal of un-servicable materials with in 20 metres lead dressed stone in Cement Mortor in all leads and lifts.

Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work,blasting work,chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15cm.layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing oof all surplus excavated soil as directed in all leads and lifts and soring/strutting timbering and dewatering where ever required to the entire satisfaction of the Engineer-in-Charge.

Stone soling properly hand packed tightly under floors in all leads and lifts and as per entire satisfacton of the Engineer-in-Charge..

Providing and laying cement concrete 1:3:6(1cement:3 sand:6 graded stone agg. 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth in all leads and lifts.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frames 30x30x5 mm, so as to give a fair finish including centering ,shuttering, propping etc.with wooden battens and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for-in-situ reinforced concrete and plain concrete work in:- Vertical surface such as walls(any thickness) partitions and the like including attached pillasters, butteresses, plinth and string courses and the like in all leads & lifts. Vertical surfaces such as walls (any thickness) partition and the like including attached pillaster,buttresses plinth and string courses and the like in all leads and lifts.

Beam, cantilever, girders and lintels :- Sides and soffits of beam, beam haunching, cantilever, bressumers and lintels not exceeding 1 mtr. in depth in all heights from floor in all leads and lifts.

Flat surfaces such as soffits of suspended floors,roofs,landings and the like floors etc.upto 200mm in thickness in all leads and lifts.

Edge of slab and breaks in floors and walls under 20 cm wide in all leads and lifts.

Providing and laying cement concrete 1:2:4 ( 1cement:2 sand: 4graded stone aggregate 20 mm nominal size )and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :- Suspended floors, roofs,landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level in all leads & lifts.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two level in all leads and lifts.

Stone work in plain ashlar cyclopean in superstructure upto floor two level including pointing with cement Motor 1:2 (1 cement : 2 sand) in :-cement Motor 1:6 (1 cement : 6 sand) in all leads and lifts.

Half brick masonry in common burnt clay building bricks in cement mortar 1:4 (1cement:4 sand) in all leads and lifts 1st class Bricks.

Providing and Laying clay tiles over mumty roots grouted with cement mortar 1:3 (1cement:3 sand over a 12 mm layer of cement motor 1:3) and finished neat in all leads and lifts.

6mm thick cement plaster to ceiling in cement mortar 1:3 (1cement:3 sand) in all leads and lifts.

20 mm cement plaster in single coat on rough side of brick/concrete/ stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement:6 sand) in all leads and lifts..

Steel work welded in built up sections,trusses and framed work ,including cutting,hoisting ,fixing in position and applying a priming coat of red lead paint:- In gratings framed guard bars, ladders, railing, brackets and similar works in all leads and lifts.

Providing 40 X 3 mm iron hold fast 40 cm long including fixing to frame with 10 cm dia bolts, nuts and wooden plugs and embending in c.c. block 30X10X5 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size in all leads and lifts.

Painting two coats(excluding priming coat)on previously painted and steel and other metal surface with readymixed paint brushing, finishing oil, glass to give an even shade including cleaning the surface of dirt, dust and other foreign matters with ready mixed paint other than white in all leads and lifts.

Providing and laying cobble stone 100 mm X 100 mm X 100 mm as per entire satisfacton of the Engineer-in-Charge.

Wall painting(two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface in all leads and lifts.

Providing and fixing 0.60 mm thick preprinted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyester (RNP) ornanic coating of 20 micrones over 5 micrones primer coating to back coat of polyester of 5 microns over 5 micrones primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with preprinted limpet and rubber washers complete with all accessories as required as per the direction of the Engineer-in-charge in all leads and lifts.

Providing and fixing ridges or Hips 60 cm over all with 0.60 mm thick preprinted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyester (RNT) ornanic coating of 20 micrones over 5 micrones primer coating to back coat of polyester of 5 microns primer coating i/c fixing with prepainted iron J or L or hooks, bolts and nuts 6 mm dia metre with preprinted limpet and Vitumen washers complete with all accessories as required as per the direction of the Engineer-in-charge in all leads and lifts.

Writing letters or figures on any surface with black Japan paint up to 15 cm height (stops, comas, hyphens and the like not to be measured and paid separately) block letters / figures in all leads and lifts

Tek Singh

Akshay kumar cont.

ASHEESH DEV

Munish Dwivedi