SPECIAL REPAIR TO EXISTING WATER TANK (P-26), BUILDING NO. P-21F AND LIBRARY AT NAVAL BASE OKHA UNDER GE (NAVY) PORBANDAR

Amount

Demolition of brick work or stone/ boulders masonry, built in cement mortar, including all quoins, arches, pillars etc., but excluding ashlars facing, dressed stone work and precast concrete articles complete as specified and directed.

Taking down chowkhat or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 m Sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5Sqm and n exc. 4 Sqm each, complete all as specified and as directed.

Demolition of (reinforced/ unreinforeced) cement concrete of any description and in any position not otherwise specifically provided for complete as specified and directed.

Dismantling wrought iron, mild steel or structural steel work of any description and in any position complete as specified and directed.

Dismantling of stone slabs and tiles laid bedded and pointed in any mortar thickness in floors, aprons and wall claddings complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, complete as specified and directed.

Dismantling AC (Corrugated / semi corrugated etc.) sheets in roof covering / wall panelling complete as specified and directed.

Dismantling of wall and ceiling board (Fibre, Pulp, insulation etc.) or insulation board /slab/ blankets, any thickness including cover fillets complete as specified and directed.

Taking up or down steel tubing and connections,of size 15 to 32mm bore complete as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / disintegrated rock complete as specified and directed.

PCC 1:4:8, type D-2, using (40mm graded stone aggregate) as foundation, filling and mass concrete complete all as specified and directed.

RCC (Design Mix ) M- 30 (using 20mm graded stone aggregate),as in columns, pillars, piers posts & struts etc. etc. complete all as specified and directed.

Precast cement concrete 1:1.5:3 type A1 using (12.5 mm graded crushed stone aggregate ) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, shelves and similar articles including use & waste of form work complete all as specified and directed.

RCC (Design Mix ) M- 30 (using 20mm graded stone aggregate),as in slabs supported on walls, beams, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete as specified and directed.

Mild steel CRS bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

CRS steel deformed or twisted bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips complete as specified and directed.

Rolled MS steel work in tubular trusses and tubular posts including special shaped washers etc., complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 graded ST 240 complete as specified and directed.

MS lewis bolts, screwed one end with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, n. exc. 15cm long and n. exc. 30cm long, dia of neck 20mm complete as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams with fair finished surfaces of concrete in flat complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs and similar works n. exc 200mm thick (horizontal or sloping) with fair finished surfaces of concrete in flat complete as specified and directed.

Hard core of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 150 mm thick, watered and rammed to a true surface, before concerting or otherwise complete all as specified and directed.

Moorum / red bajri filling brought from out side MD land, in floors or paving, laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

Damp proof course in cement concrete 1:2:4 type B-0 to horizontal surfaces including necessary formwork 25mm thick complete as specified and directed.

Stone masonry walling or squared walling in cm 1:6, brought upto courses using dressed same size Porbandar stone of superior quality complete all as specified and directed.

High tensile galvalume sheets colour coated single skin high rib / multi rib TMP Profile Galvalume sheeting in roof having 1000-1020 mm width 28 mm high crest @ maximum 250 mm pitch (centre to centre) and minimum 190mm manufactured out of 0.50 mm TCT (total coated thickness) cold rolled steel, having yield strength 550MPa minimum and wall coated with 25 micron modified polyester paint system applied on Zincalume on top and with back coating on sheet shall be 7-10 micron epoxy paint. The sheet shall be supplied in length maximum upto 6-12 meters long to suit with structural dimensions and fixed with self tapping screws with built in gasket (with bitumen washer) of suitable size machine fixed as per manufacturer instructions and applying adhesive compound to joint overlap of sheets complete all as specified and directed by Engineer-in-Charge.

High tensile galvalume sheets colour coated single skin plain Galvalume sheeting in ridge and cladding having 1000-1020 mm width manufactured out of 0.50 mm TCT (total coated thickness) cold rolled steel, having yield strength 550MPa minimum and wall coated with 25 micron modified polyester paint system applied on Zincalume on top and with back coating on sheet shall be 7-10 micron epoxy paint. The sheet shall be supplied in length maximum upto 6-12 meters long to suit with structural dimensions and fixed with self tapping screws with built in gasket (with bitumen washer) of suitable size machine fixed as per manufacturer instructions and applying adhesive compound to joint overlap of sheets complete all as specified and directed by Engineer-in-Charge.

Preparation of new steel or iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete as specified and directed.

Taking down cement plaster on brick, stone or concrete surface including racking out joints hacking for key scrubbing down with water to receive plaster etc complete as specified and directed.

Vitrified Ceramic tiles 10 mm thick, Light shade coloured (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including screed bed or bedding layer 20mm thick in cement mortar 1:6 complete all as specified and as directed.

Vitrified Ceramic tiles 10 mm thick (square / rectangular) area of each tiles not exceeding 0.36 sqm, as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed.

Glazed ceramic tiles, coloured (light colour as approved), of size 450X 350X 7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over 15mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete as specified and directed.

Non skid Ceramic coloured Joint free tiles of size 400 x 400 x 8mm thick (area of each tile exceeding 0.11 Sqm but n.exc. 0.18 Sqm) as in floor set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles over and including 20mm thick bedding layering cement mortar (1:6) complete as specified and directed.

25mm bore CPVC pipes, UV stabilised, SDR 11 pressure bearing capacity 28.12 KG/sq.cm @ 23 C ,leak proof, tough, rigid and suitable, fixed to walls with clamps / ceiling / concealed in wall including cutting chases and making good, or laid in trenches / jointed with sealant solvent leak proof including all fittings elbow, Tee, Socket, Reducer, Bushing, Step over head bends, End cap, End pugs, union, tank nipple and special fittings (brass insert threaded) like male, female treads, adapters, brass tee & reducers, male brass threaded adaptor, female brass threaded adaptor, flange including making Suitable size of brass threaded terminal to match the CP/PTMT plumbing fittings and interconnections as required for internal and external water supply applications complete all as specified and as directed.

20mm (outer dia) CPVC pipes, UV stabilised, SDR 11 pressure bearing capacity 28.12 KG/sq.cm @ 23 C ,leak proof, tough, rigid and suitable, fixed to walls with clamps / ceiling / concealed in wall including cutting chases and making good, or laid in trenches / jointed with sealant solvent leak proof including all fittings elbow, Tee, Socket, Reducer, Bushing, Step over head bends, End cap, End pugs, union, tank nipple and special fittings (brass insert threaded) like male, female treads, adapters, brass tee & reducers, male brass threaded adaptor, female brass threaded adaptor, flange including making Suitable size of brass threaded terminal to match the CP/PTMT plumbing fittings and interconnections as required for internal and external water supply applications complete all as specified and as directed.

15mm (outer dia) CPVC pipes, UV stabilised, SDR 11 pressure bearing capacity 28.12 KG/sq.cm @ 23 C ,leak proof, tough, rigid and suitable, fixed to walls with clamps / ceiling / concealed in wall including cutting chases and making good, or laid in trenches / jointed with sealant solvent leak proof including all fittings elbow, Tee, Socket, Reducer, Bushing, Step over head bends, End cap, End pugs, union, tank nipple and special fittings (brass insert threaded) like male, female treads, adapters, brass tee & reducers, male brass threaded adaptor, female brass threaded adaptor, flange including making Suitable size of brass threaded terminal to match the CP/PTMT plumbing fittings and interconnections as required for internal and external water supply applications complete all as specified and as directed.

Powder coated aluminium anodised frame and shutter for doors, windows and partitions with one or more rebates including necessary joining cleats, glazing clips, rubber neoprene packing, handle, stoppage, locking arrangements etc complete with powder coating of approved colour minimum thickness 50 micron complete all as specified and directed.

Aluminium anodised grill (Grill No. 20) of make 'DECO GRILL' or equivalent approved make as approved by GE in writing including making opening for handle & fittings, fixed with and including aluminium (anodised) channel section 38mm x 12mm x 1.30mm or F Section complete all as specified and directed.

4mm thick sheet glass, ordinary quality in square n exc 0.5 sq. m in each pane fixed to aluminium window complete as specified and directed.

6.3mm thick sheet glass, ordinary quality and glazing in square not exc 0.5 sq. m in each pane fixed to aluminium window complete as specified and directed.

12 mm Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with to aluminium frame work complete as specified and directed.

Curtain Rod Decorative aluminium alloy Powder coated tubular curtain rod, superior quality 25mm dia or above fixed in repair complete as specified and directed.

Curtain Rod Bracket aluminium powder coated decorative type fixed in repair complete all as specified and as directed

Vitreous China wash hand basin white flat back, size 550mm x 400mm, cutting for and pinning in ends of brackets Including waste pipe, brass waste coupling, 32 mm bore chromium plated brackets, restoring all connections fixed in repairs complete all as specified and directed.

Vitreous China wash down water closet (Pedestal pattern) white with concealed S-Trap/P-trap, 360mm wide, 390mm high and 415 to 445mm long at top including fixing bolt Plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated hinging device including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete, fixed in repairs, complete all as specified and directed.

Health faucet with flexible pipe (ABS body) with 01 meter long tube & wall hook Make Jaquar Model No ALD-chr-583 or equivalent model of make specified, fixed in repairs, complete all as specified and as directed.

Vitreous china (White) half stall urinal with grating, union for discharge pipe, spreader, incl 40mm dia PVC heavy duty waste pipe upto floor trap, fixing with brackets, flush pipe, union for discharge pipe, connection pipe , Incl fixing in Urinal spreader and restoring connection fixed in repair complete as specified and directed.

110mm bore PVC (SWR) pipes of pressure rating 4 Kgf / cm2, single socketed in any length with rubber ring, laid in trenches/ fixed to wall /ceiling, complete as specified and directed.

75mm bore PVC (SWR) pipes of pressure rating 4 Kgf / cm2, single socketed in any length with rubber ring, laid in trenches/ fixed to wall /ceiling complete as specified and directed.

75mm dia bore, PVC (SWR) bends, , any radius with rubber ring , including fixing clips, laid in trenches/ fixed to wall /ceiling complete as specified and directed.

110mm dia bore PVC (SWR) bends, any radius with rubber ring including fixing clips laid in trenches/ fixed to wall /ceiling complete as specified and directed.

75mm(outlet) PVC (SWR) floor trap, plain including jointing with solvent cement and white cement complete as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete as specified and directed.

PVC low level flushing cistern 10 litres capacity valve less symphonic action type, ISI Marked white with inlet, ball valve, float and handle including brackets, fixed in repairs,complete as specified and directed.

Angular stop valve brass 15mm bore, Capstan head chromium plated, with wall flange, fancy type screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe fixed in repair complete all as specified and directed. Make: Model 7310 of Prayag or eq model of make specified in Appx 'B' hereinbefore.

Pillar tap brass 15mm bore, with capstan head chromium plated fencing type screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe fixed in repair complete all as specified and directed. Make: Model 7302 of Prayag or eq model of make specified in Appx 'B' hereinbefore.

Bib tap ,brass 15mm bore, concealed type with capstan head chromium plated, with wall flange, fancy type screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe fixed in repair complete all as specified and directed. Make:- Model 7608of Prayag or eq model of make specified in Appx 'B' hereinbefore.

Brass chromium plated shower rose 120mm size and 15mm dia with swivel joint and arm including fixing to steel pipe or union complete fixed in repair complete all as specified and directed.

600 mm long PVC connection Low density polythene pipe (LDPE) of pressure rating 6 KG per Sq.cm suitable of 15 mm nominal bore GI pipe complete with brass chromium plated unions and rubber washers. The weight of brass coupling nuts shall not be less than 40 grams. The weight of PVC pipe shall not be less than 63grams fixed in repair complete all as specified and directed.

110mm(outlet) PVC (SWR) floor trap, plain including jointing with solvent cement and white cement complete all as specified and as directed.

M&L Cutting into existing manholes for connecting new drains 150mm bore , making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and deforming benching as required complete all as specified and directed.

Soap dish of size 160 x 160 x 90mm of superior quality acrylic fixed with plugs with chromium plated brass screws, fixed in repairs, complete all as specified and as directed.

Preparing old decorated surfaces distempered or painted surface of wall and applying two coats of oil bound distemper complete all as specified and directed.

Grating PTMT 100 mm dia,(min weight 100 Gram) with hole for wash basin complete all as specified and directed.

Acrylic corner shelf of dia 25cm (inner quarter circle shape) fixed with brass & screws complete all as specified and as directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exc. 25 cm deep as in soft rock complete as specified.

Granite of Ist quality 18 to 20 mm thick machine cut, table rubbed and polished as in flooring, steps tread, jambs, pillar, window-cills in single piece including nosing and two nos friction groove, laid over and including 20 mm thick screed bed in cement mortar (1:4) bedded and jointed with grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite stone complete all as specified and as directed.

Aluminium alloy wire cloth of superior quality 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with FI clamp 20x5mm to water tank Air vents complete all as specified and as directed.

Hydraulically aluminium extruded section body door closer regulated designation No 1 universal type suitable for door shutters up to 700mm in width and weight not exc 35 KG etc, fixed in repairs complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair / replacement complete all as specified and directed.

Stainless steel butt hinges cold rolled medium wt 100mm size complete all as specified and directed.

150 mm long extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, overall length of cover plate 140mm complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and as directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

Preparing old decorated surfaces by complete removal of existing treatment, scraping down, washing, rubbing down and stopping of painted surface of walls & ceiling including roof projection / chajjas and applying two coat of weather proof Acrylic based exterior emulsion paint complete all as specified and directed.

Preparing newly plastered surfaces of walls & ceiling including roof projection / chajjas and applying two coat of weather proof Acrylic based exterior emulsion paint over a coat of compatible primer complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

Preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

Rendering 5 mm thick in cm 1:3 on ceilings finished even and smooth without using extra cement complete all as specified and directed.

Rendering 10mm thick in CM 1:4 on fair faces of concrete surfaces, even & smooth with out using extra cement including use of water proofing compound complete all as specified and directed. (Note- Water proofing compound shall be measured and paid separately).

Rendering 15 mm thick in two layers (10+5mm) ,on fair faces of stone masonry surfaces or concrete surfaces in cement mortar 1:4 finished even & smooth with out using extra cement including use of water proofing compound in outer layer complete all as specified and directed. (Note- Water proofing compound shall be measured and paid separately).

Preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper (oil emulsion), over a coat of competible primer as per manufacturer's recommendations on walls complete all as specified and directed.

Rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) 500 Litre capacity, hoisted and fixed in position, with lid, tounge nipple for inlet, outlet connections etc. fixed in repairs, complete all as directed by Engr-in-Charge.

10mm thick plaster of Paris (POP) moulding of approved design and pattern on junction of wall and ceiling after scraping off existing treatment and preparation of surfaces by hacking to form key to hold the plaster of Paris in level and line, finishing, cleaning the surface complete all as specified and as directed.

Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including hangers and hanging arrangements, including providing and fixing 12 mm thick Seamless calcium silicate ceiling board made out of1800 x 1200mm size board, comprising of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having Phillips head with under head cutter at minimum spacing of 200mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish and multi layer design, complete all as specified and as directed.

Anodised aluminium snap gridframe work for false ceiling at any height of size with 600mm x 600mmgrid and Snap grid frame work shall be fixed to ceiling with supporting hanger consisting of 6mm dia mild steel rod, J bolts with necessary bolts, nuts and washers all asmanufacturer’s instructionThe main and cross tees jointed at junction/crossings with anodizedaluminium angle bracket of size15mmx15mmx1.5mm, weighing 0.12 Kg per running metre,Main/cross tee section shall be supported at ends all along the wallwith anodized aluminium angle of size 40mmx25mmx2mm, weighing 0.36 Kg per running metre, including providing and fixing 12 mm thick Seamless calcium silicate ceiling board, comprising of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having Phillips head with under head cutter at minimum spacing of 200mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish and multi layer design, complete all as specified and as directed.

Weld mesh, weight not less then 4 KG per sqm any thickness or mess, fixed with steel or wood fillets, if any straining bolt etc incl binding wire (if min (weight 4KG /sqm not available then contractor has to provide next higher weight without extra cost) complete all as specified and as directed.

RCC M-30 (Design Mix) (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footing plinth beams, bases for column etc. complete all as specified and directed.

RCC (Design Mix ) M- 30 (using 20mm graded crushed stone aggregate),as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and directed.

Use and waste of form work to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc.; vertical or to batter with rough finished surfaces of concrete in flat complete all as specified and directed.

Use and waste of form work to sides of concrete, foundation, footings & plinth beams and similar works with rough finished surfaces of concrete in flat complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Rolled Mild Steel Plates (plain or Chequered) channels, square cut or notched, forming holes, without any attachment, for fixing to truss confirming to Fe 410 – S all as specified & as directed.

Stone masonry walling or squared walling in cm 1:4, brought upto courses using dressed same size Porbandar stone of superior quality complete all as specified and directed.

20 to 25 mm thick Kota stone slab as in flooring laid over and including 20mm thick screed bed in cement mortar (1:4), set & jointed in grey cement slurry mixed with pigment to match shade of slab, including rubbing grinding and mirror polishing complete all as specified and directed.

PCC 1:1.5:3 type B-1 using (12.5 mm graded crushed stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, drain beds kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, and similar work including use & waste of necessary form work complete all as specified and as directed.

Stainless steel (Grade-304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, incl fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc, of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc) complete all as specified and directed.

18 to 22 mm thick kota stone slab as in skirting, riser of steps and pillars over and including 15mm thick rendering in cement mortar (1:4) including rubbing grinding and mirror polishing complete all as specified and directed.

Complete removal of loose / cracked concrete incl reinforcement if required, from RCC roof projection, chajjas, fins, facia etc and making good with Reinforced cement concrete (nominal mix) 1:1.5:3 ype A-1 (12.5 mm graded aggregate) in any slab and in any position finished the surface even and smooth without using extra cement including necessary form work and welding/binding of reinforcement (including reinforcement) if required complete and match with the existing surface as directed by the Engr- in -Charge.

Preparing old decorated wall surfaces by complete removal of existing treatment, scraping down, washing, rubbing down and stopping of distempered or painted surface and applying 2- 3mm thick wall care putty in two or more coat complete all as specified and directed.

Preparing newly plastered surfaces of wall and applying 2- 3mm thick wall care putty in two or more coat complete all as specified and directed.

35mm thick , 2nd class hard wood Glazed and skeleton shutter for windows, open rebated and prepared to receive glass , gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of member of shutter as specified in SSR part-I section 8, clause 8.24 (a) supplied and fitted to chowkats etc. complete all as specified and directed.

2nd class hard wood Plain fillets square, rectangular or triangular in section exc 13& n exc 25 sqcm clean sawn, secured with nails or brands but bull-nosed, splayed, chamfered or rounded on one edge or face, wrought and fixed with screws complete all as specified and directed.

Preparing of new wood or wood based surfaces over 10 cm width and girth and applying two coat of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

Chequered cement concrete coloured tiles ( grey cement mixed with pigment) 20cmx20cmx40mm thick set over & including 20 mm thick bedding layer in cement mortar (1:6) with neat cement and pointed in grey cement mixed with pigment to match the shade of tiles, complete all as specified and as directed.

25mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both faces covered with decorative face veneer with lipping/frame to match, complete all as specified and as directed.

100mm long, hasp and staple, aluminium anodised safety type, with mild steel hinge pin including bolt to hinge plate, fixed with screws, complete all as specified and as directed.

75mm thick PCC 1:3:6 , type C-1 using (20mm graded stone aggregate) as in plinth protection finished even & smooth without using extra cement making 10mm wide joints at every 3m interval and at every corner, filled with mixture of bitumen and sand (1:1), complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete on and including teak wood battens including fittings, such as switches, ceiling roses, pendent brackets, holders etc. but excluding fan regulators, tube light fittings and removing complete and making good to disturbed surfaces of walls, floor etc. with its original specifications all as specified.

Point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC concealed conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories and replacement of sunk zinc coated pressed steel terminal box of 1.60mm thick with 3mm thick plastic laminated sheet top cover, brass screws, cup washers etc including all cutting / chases etc in walls complete all as specified and directed for the following :- One light or fan point controlled by one one way switch

All as per item No 113 above but for One 5 Amps 3/5 pin socket outlet on same board with other switches.

All as per item No 113 above but for One 5 Amps 3/5 pin socket outlet on independent board .

All as per item No 113 above but for One bell/ buzzer point controlled by one push button independent .

All as per srl item no 113here-in-before but for 15 amps switch socket combination outlet on independent board with 2.5 sq mm PVC unsheathed (FRLS) wire along with 2.5 sq mm green colour wire FRLS as earth continuity conductor connected to common earth dolly complete all as specified & as directed by Engr-in-charge.

Taking down sub main wiring and making good disturbed surfaces of wall / floor etc. complete all as specified and as directed.

Sub main wiring concealed with two runs of single core 6 Sqmm (Nominal area) cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, ISI marked with copper conductor drawing into rigid non-metallic PVC concealed conduit complete with including one run of 6sqmm (nominal area) single core PVC insulated multistrand unsheathed FRLS copper conductor as earth wire and duly connected to all common earth point, complete all as Specified and directed by Engr-in-Charge. (Conduet shall be measured and paid separately).

Ceiling rose surface bakelite 65x50mm 3 terminal complete all as specified and directed.

Sub main wiring concealed with two runs of single core 4 Sqmm (Nominal area) cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, ISI marked with copper conductor drawing into rigid non-metallic PVC concealed conduit complete with including one run of 4 sqmm (nominal area) single core PVC insulated multistrand unsheathed FRLS copper conductor as earth wire and duly connected to all common earth point, complete all as Specified and directed by Engr-in-Charge. (Conduet shall be measured and paid separately).

20 mm rigid non-metallic PVC concealed conduit medium grade including all PVC conduit accessories, cutting / chases and making good disturbed surfaces complete all as specified and directed.

Modular white cover plate suitable for 1 modules with frame complete all as specified and directed.

Modular white cover plate suitable for 3 modules with frame complete all as specified and directed.

Modular white cover plate with frame 8 modules complete all as specified and directed.

Modular switch, 06 Amps, single pole, one way, 250 volts, one module and IP 20 protection complete all as specified & directed. Make : Legrand, Cat No : 6755 01, Havell's Cat No : AHCSXXW101/061 or Philips, Cat No : 913702314401 complete all as specified.

Modular switch, 16 Amps, single pole, one way, 250 volts, one module and IP 20 protection complete all as specified & directed. Make : Legrand, Cat No : 6755 13 or Havells, Cat No : AHCSXIW161 or Philips, Cat No : 913702314801 complete all as specified.

Modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete all as specified & directed. Make : Legrand, Cat No : 6755 50 or equivalent in Havells, Cat No : AHLKPXW065 or Philips, Cat No : 913702309701 complete all as specified.

Modular socket outlet 02 in 01, 03 pin, 06 Amps and 16 Amps, 02 module with shutter complete all as specified & directed. Make : Legrand, Cat No : 6755 55 Havells, Cat No : AHLKCXW163 complete all as specified.

Ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, hum free, AC, 230 volts, 100 watts, duly ISI marked complete all as specified & directed. Make: - Legrand, Cat No. 6755 30 or Havells, Cat No : AHLRFHW005 complete all as specified.

Modular bell push with indicator, 06 Amps, single pole, one way, 250 volts, two module and IP 20 protection complete all as specified & directed. Make : Legrand, Cat No : 6755 06 or Havells, Cat No : AHLMXIW101/061 complete all as specified.

Bell, AC, 230 volts, single pole, ding dong type on and including 03 mm thick plastic laminated hylam sheet fixed on wall of suitable size with brass screws and washers etc complete all as specified and directed.

Taking down existing ceiling fan / exhaust fan any size, any make, refixing the same after replacing the rubber bushes, split pin, servicing, greasing and painting with two coats of synthetic enamel paint etc complete all as specified and directed.

Exhaust fan 300mm sweep AC, 240 volts fixed as per manufacturer instruction, connecting with and including 1.5 Sqmm copper conductor, PVC insulated and PVC sheathed three core cable complete all as specified & directed by Engr in charge. Make :Bajaj Maxima Dx 300mm or eq model of make specified in Appx 'b' hereinbefore.

DB box MCB Protected Socket With sheet steel Enclosure single pole 20 Amp with 3 pin plug top for AC connection from Socket point to stabilizer complete all as specified and as directed. Make :- Havells Cat No- 20 A MCB DBOXX COMBO or its equivalent model of make specified in Appx 'b' hereinbefore.

SKYLUX LED 43 Watt natural white Efficient LED recessed 2x2 luminaire to enhance the delight of occupants with comfortable experience through its classic design & glare free soft illumination, White powder coated CRCA housing, extruded metal/aluminium body, electronic LED driver, connector block with all accessories internal prewired & connecting up with 2 core flexible copper conductor cable of suitable size, seamless front frame with white high transmission acrylic cover, fixing on fall ceiling with wiring from ceiling rose to light fitting complete all as specified and as directed. Make :- Bajaj Cat No -BZRSQL 43W GZi NW or its equivalent model of make specified in Appx 'b' hereinbefore.

LED Adore 10 W CDL Ball Lamp, E-37holder base with polycarbonate body and aluminium heat sink warm white 10 Watt complete all as specified and directed by Engineer - in - Charge. Make:Havells Cat Part No: LHLDERHEML8XO10 or equivalent cat part of make specified .

Lamp holder insulated body with back plate for batten fittings fixed in repair / replacement complete all as specified and directed.

10 W LED batten integrated LED Channel with white acrylic cover type fitting with LED tube rod including connecting up with twin core twisted flexible copper conductor from ceiling rose to fitting complete all as specified and as directed by Engineer-in-Charge. Make:- Bajaj Cat No 112408/BCLSB 10 W NW or equivalent model of make specified .

Surface and wall mounted 20 watt batten LED with Integrated LED channel engineering plastic batten with white acrylic cover, polycarbonate co-extrusion tube for LED light housing with Engr plastic end caps,Co-extrusion tube top parts is made of white polycarbonate material and the bottom is made of opal diffused polycarbonate material with groove inside for PCB and 2 ft long including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 0.75 Sqmm copper conductor from ceiling rose all as specified and as directed. Make:- Bajaj Protect Code : 112798 Cat Part No:BCLSB 20 WH or Its equivalent of make specified .

Building street light fitting Endura pearl 20W LED lamp new generation energy saving & environmental friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening separate driver compartment with IP65 protection and impact resistance of IK07,with suitable of GI pipe (light grade) bracket and clamps,nut bolts are fixed on wall/post and including electrically connecting with three core PVC insulated pvc sheathed cable of 2.5 Sqmm copper conductor from ceiling rose/ Junction box, all as required and directed Make : Havells cat no ENDURAPEARLSL20WLED757SASYTOPC or its equivalent model of make specified

Sheet metal enclosure, double door, single pole and neutral, AC, 240 volts, 12 way, with 200 Amps rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing, fixed in repair / replacement complete all as directed by Engineer - in - Charge.

Sheet metal enclosure, double door, single pole and neutral, AC, 240 volts, 8way, with 200 Amps rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing, fixed in repair / replacement complete all as directed by Engineer - in - Charge.

Sheet metal enclosure, double door, single pole and neutral, AC, 240 volts, 4way, with 200 Amps rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing, fixed in repairs, complete all as directed by Engineer - in - Charge.

MCB SP 240 Volts AC 6 - 40 Amps of breaking capacity 10 KA B curve, fixed in repair / replacement complete all as specified and directed.

MCB SPN 40 Amps,10 KA breaking capacity 'B' Curve suitable 230 V,50 Hz for lighting and other domestic load fixed in repair / replacement complete all as specified and directed by Engineer - in - Charge.

MCB TPN 40 Amps, 10 KA breaking capacity , C Curve suitable for 230 V, 50 Hz AC Supply, fixed in repairs, complete all as specified and directed by Engineer - in - Charge or compatible model cat part of make as specified in Appx 'B' hereinbefore.

RCCB 63 Amp FP 100 mA,Four pole,240V,50Hz,IP-20,protection against earth fault/leakage current conforming IS-12640-12000,IEC 61008-1,fixed in repair complete all as specified and as directed.

Modular white cover plate with frame 12 modules fixed in repair complete all as specified and directed.

12 mm thick hard Wood Box suitable for SPN 4 way to 12 way DB as per existing size and pattern including suitable masonary work, surface finish as per original and locking system fixed in repair complete all as specified and directed.

12 mm thick hard Wood Box suitable for TPN DB as per existing size and pattern including suitable masonary work, surface finish as per original and locking system fixed in repair / replacement complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, pipe line, cable , etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exc. 25 cm deep as in soil complete as specified.

Removing excavated material (soil/ rock) to distance not exc 50 m and depositing where directed at a level not exc 1.5m above the starting point,complete all as specified and directed.

Fine dry river sand cushion in trenches for cable protection with a layer of sand 8cm thick before laying of cable and 15cm thick after laying of cable in trenches complete all as specified and directed. NOTE: - Only compacted thickness will be measured and paid.

Precast concrete cable cover unreinforced, ISI marked class LV types 2 flat size 250mm x 150mm x 40mm having minimum average breaking load 200KG, complying IS:5820-1970 made of concrete used of grade M-20, laid flat in trenches over the cable with the length of concrete cover perpendicular to the direction of the cable length, adjacent / abutting each other complete all as specified.

GI tubing light grade ISI marked for cable protection at road crossing/floor/wall/ on poles or at any indicated situation etc duly sealed at both end after drawing cable including necessary clamps, saddles all as directed and specified for 40 mm bore dia, complete all as specified and directed.

Cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (Heavy duly) with stranded aluminium conductor cross sectional area 25 sqmm4core suitable for working on 1100 Volts earthed system, laid in tranches, in floor, in ducts, through pipe or along pole complete all as specified and directed. Note :- Excavation, earthwork, sand cushioning, PCC protection cover, GI pipe and protection clamps shall be measured and paid for separately.

Cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (Heavy duly) with stranded aluminium conductor cross sectional area 6 sqmm 2core suitable for working on 1100 Volts earthed system, laid in tranches, in floor, in ducts, through pipe or along pole complete all as specified and directed. Note :- Excavation, earthwork, sand cushioning, PCC protection cover, GI pipe and protection clamps shall be measured and paid for separately.

Earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 3 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work in any type of strata , salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore as watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40mm thick in PCC 1:2:4 type B1 duly reinforced with CRS Bars 8mm dia at the rate of 100mm centre to centre both way with 12mm dia lifting handle and pit / chamber constructed 50 cm away from the edge in PCC 1:3:6 type C1, Angle iron 40x40x3mm frame for pit cover including testing on completion complete all as specified and directed.

100mm spigot and socketed centrifugally cast ductile iron 'K-7' pressure pipe in any length conforming to IS-8329-2000 with necessary jointing with EPDM gasket push on (tyton joints) complete all as specified and directed.

Cast iron sluice valve of 100mm bore pressure class PN-1.6 type (IS 13095 marked ) flanged and drilled at both ends having gun metal spindle and rings including wheel for operating all as specified including two numbers flanged socket and jointing materials such as bolts, nuts, washers, rubbers/ fibre board gasket complete all as specified and directed.

Construction of valve chambers 1000 mmx1000mmx1000 mm with 15 cm thick solid concrete block masonary, block casted using PCC 1:3:6 type C-1 mix built in cement and sand mortar 1:4, 15 mm plaster to internal surfaces and external surfaces up to 15 cm below ground level and top of floor in CM 1:4 finished even and smooth without using extra cement, 2 mm thick MS sheet cover including 40x40x6 mm MS angle frame embedded in 150 mm thick PCC 1:2:4 type B-1, with 25x6 mm flat iron hold fast, handles, hinges with locking arrangements, applying one coat of red oxide primer and two coat of synthetic enamel paint to all steel surface and earth work in soft /disintegrated rock disposal of surplus soil to a distance n.exc.50 m. complete all as specified and directed.

Supply & fix and testing Water meter 100 MM Dia ,Bulk enclosed Dry Dial Type ,Hydrostatic pressure 16 KG /cm 2 with all fitting (Nut,bolts, washers, rubber packing etc) complete all as specified and as directed.

Supply & fix and testing 100 mm dia 'Y' Strainer with all fitting (Nut,bolts, washers, rubber packing etc) complete all as specified and as directed.

Supply and fixing Mechanical joint at tapping pipe of 150mm dia including nuts, bolts, washers and 03 Nos, rubber ring complete all as specified and as directed.

M & L for fittings / specials for DI spigot socketed pipes such as bends of any type, radius and angle tapers any type (straight, bend increasing, decreasing or double sockets etc) Tee pieces single branch 'Y' junction, double branch, cross (all sockets or socket and spigot) collars, caps and plug size upto 200 mm bore, all as per IS 1538-1993, ISI marked complete all as specified and directed.

Run lead joints including spun yarn and caulking thereafter for the following sizes of CI pipes:100mm bore

Making joint using rubber or Fibre board gasket 3 mm thick required for CI flanged mains and specials for pipe size 100 mm complete all as specified.

Cutting of hard standing/ Road for laying of pipe line/cable and making good surfaces by using PCC 1:2:4 type B-2 after laying of pipe line/ cable up to 30cm in depth and removing rubbish outside MD land complete all as specified and as directed.

Making hole in RCC static tank suitable for 50 to 100 mm dia bore CI /GI Pipe and making good and leak-proof using concrete epoxy mortar after fixing of pipe complete all as specified and directed by Engineer - in - Charge.

Supply, lay, connect and test GI tubing ,medium grade with all fitting, laid in trenches, or fixed to walls, floors, ceiling or laid in trenches etc. complete of size 50mm bore complete all as specified and as directed

Gun-metal, ball valve, disc type with iron wheel, screwed both ends for iron pipe, ISI marked of size 50mm bore ,complete all as specified and as directed.

Cutting the existing water pipe line of size 50mm dia including necessary excavation & earthwork inserting GI Tee, Union & sockets for making connection complete all as specified and as directed.

Nitesh Enterprise

SHREEJI ENTERPRISE