PROVISION OF SPECIAL REPAIRS TO BLDGS NO T-475, T-39 AND T-40 OF CERTAIN UNITS AT HASIMARA UNDER GE (S) BINNAGURI

Amount

M & L for plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for RCC (Nominal Mix) M-20 grade using 20mm graded crushed stone aggregate as in Columns ,Pillars, Piers,Posts and Struts etc. complete all as specified and directed.

M&L for RCC (Nominal Mix) M-20 grade using 20mm graded crushed stone aggregate as in Chajja and similar works etc. complete all as specified and directed.

M&L for RCC (Nominal Mix) M-20 grade using 20mm graded crushed stone aggregate as in Roof Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. (Note :- Reinforcements and formwork shall be measured and paid separately)

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports over hang etc and similar works for rough finished surfaces of concrete in flat complete all as specified and directed.

Formwork to sides of pillars post, struts, piers, columns and stanctions square vor rectangular in section and similar works for rough finished surfaces of concrete in flat complete all as specified and directed.

Formwork to Chajjas and the like (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan to any radious in wall built in CM(1:6) complete all as specified and directed

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No. 9 herein before but 6 to 8mm dia .

All as per item No. 9 herein before but 5mm dia and over and including 10mm dia in stirrups, spacers and binders.

M&L rendering 10 mm thick in cm 1:6 on fair faces of brick work or concrete surfaces finishing surfaces even and smooth without using extra cement , complete all as specified and as directed.

M & L for rendering 20mm thick on brick wall or concrete surface in cement mortar (1:4) consisting two layers, top layer of 10mm thick mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid saperately.)

Supply only water proofing compound conforming to IS-2645-2003.

Taking down cement plaster of any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for 5 mm thick rendering on ceiling in CM 1:3 finished even and smooth with out using extra cement complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in floor, laid in bays,finished surface even and smooth with using extra cement complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 (Ist quality ) conforming to IS-13755, as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the surface including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and as directed. (Make- Kajaria / Asian/ Nitco)

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 (Ist quality ) conforming to IS-13755, as in Vertical surfaces such as dado,skirting,riser to steps etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface including 10 mm thick screed bed or bedding layer of cement mortar (1:4) for laying floor finishes complete all as specified and as directed. (Make- Kajaria / Asian/ Nitco)

M&L for mild steel work in tubular trusses and tubular posts including special shaped washer duly welded, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 with one shop coat of Zinc Chrome primer complete all as specified and as directed.

M&L for plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for Mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long dia of neck exc 12mm n.exc 20mm complete all as specified and directed.

M&L for high tensile 550 MPA yield strength Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering The sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium (55%)and silicon (1.5%) with total mass coating of 150 gms/sqm on both sides. Covered width will be 1020mm and sheet length as per site requirement. The profile is having return leg for proper side lap. The sheet shall be fixed using self drilling/self capping screws with EDPM seal complete all as specified and directed. Make: TATA blue scope or equivalent of METCO/JSW Ispat Ltd.

All as per item No- 23 here in above but Plain sheet as in ridges/ hips / valley and Eaves board - ditto --

M&L for mild steel Hollow section square/ Rectang -ular as in Roof trusses and purlins, Rail etc duly welded, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 with one shop coat of Zinc Chrome primer complete all as specified and as directed.

M&L for preparation of newlyplastered or unplastered surfaces of wall and applying two coats of acrylic emulsion Distemper and a coat of acrylic Primer over including preparation of surfaces complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of wall and applying two coats of acrylic emulsion Distemper and a coat of Primer including preparation of surfaces with complete removal of existing treatement complete all as specified and directed.

M&L for two coats of cement base paint to newly plastered surfaces over a coat of cement primer of wall including preparation of surfaces complete all as specified and directed.

M&L for two coats of cement base paint to old plastered surfaces over a coat of cement primer of wall including preparation of surfaces complete all as specified and directed.

S&F 35mm thick factory made, 2nd class hard wood, plain framed, panelled shutter ( two panel) double shutter with lock rails and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneered facing on both faces,the size of rail and styles as per IS: 1003 ( Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F of 2nd class hardwood factory made 35 mm thick, glazed and skeleton door shutters, open rebated and prepated to receive glass gauze etc (without sash bars) edges of framing plain, chamfered or rounded materials and revated sash bars any number , edges of framing plain chemfered or rounded fitted with cut and mitred beads for securing glass in door etc sizes of members of shutter as specified in SSR part 1 section 8, clause 8.20 (a) and fitted to chowkats complete all as specified and directed .

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F factory made Z section steel window with side hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay, ms tower bolt etc. complete with glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete all as specified and directed.

S&F for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n-exc 0.5 sqm in each pane complete all as specified and as directed

S&F factory made Z section steel window with side hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay, ms tower bolt etc. complete without glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete all as specified and directed.

S&F 150mm long mild steel barrel tower blots, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F 250mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F 150mm size Aluminiun handle, oval type,Cast type, fixed with screws complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. fixed in floor,overall length of cover plate 140mm complete all as specified and directed.

S&F of Mild steel Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) in grade Fe 410-W (Grade E-250 quality) complete all as specified and directed

M&L for preparation of newly steel and iron surface of any description width or girth exc 10 cm and applying two coats of synthetic enamel paint over a coat of Red Oxide primer complete all as specified and directed.

M&L for preparation of newly steel and iron surface of any description width or girth exc 10 cm and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L structural steel work with rolled mild steel as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and similar articles conforming to Fe-410W Gde E-250 complete all as specified and directed.

Taking out unserviceable steel work such as Steel windows/ventilators with guard bar and other section by cutting in Brick wall etc and removing from site of work complete all as specified and as directed.

M&L for preparation of newly wood or wood base materials of any description, not otherwise described over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of Pink primer complete all as specified and directed.

M & L for brick work with sub class 'B' bricks, straight or curved on plan to any radious in wall built in CM(1:6) complete all as specified and directed

M&L for 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base to floor laid in bays,finished surface even and smooth without using extra cement complete all as specified and directed.

S&F 200mm long aluminum anodized barrel tower bolt of extruded section, fixed with screws complete all as specified and directed.

S&F 300mm long aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections suitable for use with pad lock complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handle,cast type, anodised, fixed with screws complete all as specified and directed.

Demolition of brick masonary work, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding precast concrete articles etc. complete all as specified and directed.

Dismantling of structural steel work in vertical members , struts, including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, of any thickness as in roof coverings including nainital or similar pattern complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in framed work as in any position complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Taking down chowkhats or frames with shutters (without talking off shutters from the freme) area exc 1.50 and n.exc 4 Sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without talking off shutters from the freme) area n.exc 1.50 each and removing from site complete all as specified and directed.

S&F of 125mm x 60mm size pressed steel door framewith one or more rebates including fixing lugs,hinges,lock,strike plates etc. including one shop coat of priming complete all as specified and directed.

M & L for cement concrete 1:3:6 type C-2 (Using 40 mm graded stone aggregate) as in Hold Fast Blocks including Necessary Form Work complete all as specified and as directed.

S&F 4mm thick non-Asbestos fibre cement building board( E-board) false ceiling with board of size 600x600mm and aluminium anodised snap grid frame work complete all as specified and directed including all necessary drilling, cutting to fix electrical items as under:- (a) 40x25x2.0mm thick aluminuim anodised angle plugged @ 600mm c/c along perimeter of wall. (b) 36.5x25x1.4mm thick aluminuim anodised tee weighing 0.24 Kg/RM as main and 23.5x26.4x1.4 mmcross runners weighing 0.191 Kg/RM suspended with 3.0mm dia GI wire suspenders with adjustable clamps(40x3mm of required size) and dash true fastners with rawl plug and screws plugging in RCC slab placed @ 605mm c/c from perimeter of wall. (c) Fixing of 4mm thick non-Asbestos fibre cement building board( E-board) and finished complete on ceiling. NOTE: The complete ceiling work shall be done as per manufactures instruction and as directed.

M&L for 75mm thick cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate in plinth protection finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at the length n exe 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed .

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, conduit etc. including accessories including making good disturbed surface to match the existing complete all as specified & directed.

Taking down main switches, distribution board, steel enclosure with MCB’s any way and rating including wooden board or from steel board and making good disturbed surfaces complete all as specified & directed.

M&L point wiring complete for one light point or one fan/Exhaust point controlled by one, one way switch with FRLS PVC insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'heavy grade' PVC concealed conduits and fittings, including cutting chasingin brick wall n.exc 10cm width or girth(excluding ceiling surface), pressed steel concealed terminal switch boxes not less than 1.2mm thick of reqd size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed .

All as per item No 66 here in above but One point for socket outlet 5 amps on same board .

All as per item No 66 here in above but One point for socket outlet 5 amps on independent board but not below the switch board in same vertical plane

All as per item No 66 here in above but One15 Amp socket outlet point controlled by one switch using 2.5 sqmm copper conductor cable with continuous earth wire of 2.5 sqmm copper conductor on independent board.

S&F switch piano flush type, 6 amps, 230V AC,single pole, one way complete all as specified & directed.

S&F ceiling rose surface type bakelite 65x50mm three terminal complete all as specified & directed.

Supply & fixing lamp holder,insulated polycarbonate/bakelite body suitable forbatten / angle fitting complete all as specified and directed .

S&F socket out let 2 in 1, multipurpose suitable for 2 pin and 3 pin 6 amp flush type complete all as specified & directed.

S&F socket out let multipurpose type, 2 in 1 for 6 pin 6 and 16 amp flush type complete all as specified & directed.

Supply & fixing ISI marked switch piano flush button type, single pole, one way, 15/16 Amps, 240 volts for point wiring complete all as specified and directed .

S&F fan regulator, 5 step(rotary stepped), electronic type, single phase,120/180 V, 400 watt, socket size incl connection complete complete all as specified & directed.

S&F sub main wiring with two single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS 694 of size 6.0 sqmm nominal cross sectional area,1100 v grade and one run of 6.0 sqmm nominal cross sectional area FRLS PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits and fittings,complete including taking down of old sub main wiring all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

Supply and Fixing MCB DB double door, powder coated sheet metal enclosure, 8 way 240 volts grade single pole and neutral with 200 amps rated bus bar,IP-43 fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified and as directed.

S&F MCB single pole & neutral 40 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F in repair MCB tripple pole & neutral 32 amp, 415 volts, 'C' series, 50 Hz,10 KA breaking capacity,two position din rail clamp, integrated label channel holder, sealed calibration screw, & making connection complete all as specified and directed.

S&F surface & wall mounted 18 watt LED batten light fittings with extruded Aluminium housing complete with constant current electronc driver all accessories including provision of three core PVC cable of copper conductor of size 23/.0076 and making connection complete all as specified and directed. (Make : Crompton cat No- LCTL 18 CDL or equivallent model of Havells/ Philips/Wipro.)

S & F in repair Moulded Case Circuit Breaker (MCCB) FP with adjustable thermal fixed magnetic release, capacity 100 Amps, line load independability, with horizontal mounting facility , 415 , 50 Hz , 10 KA, including making necessary connection with spreader, link and copper lugs including taking down old unserviceable MCCB /Main switch of any capacity and make from position complete all as specified and directed.

M&L for in replacement Factory made Metal box made out of 2mm thick MS sheet of size 350mm(B) x 400mm(H) x200mm(D) with single door hinged shutter and locking arrangement for fixing MCCB with and including flashed/grouted on wall,duly painted with two coats of Synthetic Enamel paint (powder Coated) over a coat of Red Oxide primer and making good disturbed surfaces of walls with plaster work and surface finish complete all as specified and directed .

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified and directed.

S&F in repair LED lamp9/10W,B-22 complete all as specified and as directed. Make :- Phillips/ WIPRO/ GE)

SCHEDULE OF CREDIT Rate quoted by the Tenderer for this schedule should not be less than rate assessed by the department shown on estimated rate column for the respective items.

Old unserviceable Timber scantling of any length etc obtained from dismantling.

Old unserviceable chowkhats or frames with shutters area n.exc 1.50 sqm each including iron mongery obtained from dismantling.

Old unserviceable chowkhats or frames with shutters area exc 1.50 sqm but n.exc 4.0 sqm each including iron mongery obtained from dismantling.

Old unserviceable stainless steel/MS wire cloth of any type obtained from dismantling.

Old plain/corrugated steel sheets excluding J/L hooks of any type obtained from dismantling.

Old unserviceable steelwindows of any size/type etc obtained from dismantling.

Old unserviceable iron scrap of any type obtained from dismantling.

Old unserviceable Brick bats of any size obtained from dismantling.

Old unserviceable ceiling boards of any type with cover fillets obtained from dismantling.

Old U/S batten/Conduit point wiring materials except fittings such as switches,sockets,bell push,ceiling roses,lamp holder,fan regulators etc any type obtained from dismantling.

Old U/S wiring fittings such as switches,sockets,bell push,ceiling roses,lamp holder,fan regulators etc any type obtained from dismantling.

Old U/S Main switches/DB's etc ,any size obtained from dismantling.

Old U/S Sub main wiring materials with fittings obtained from dismantling.

Old unserviceable MCB's of any type obtained from dismantling.

Old unserviceable Earthing Materials of any type obtained from dismantling.

M/S ASHOK ENTERPRISE

M/S. KUMAR CONSTRUCTION CO.

SRI HANUMAN PRASAD AGARWALLA

M/S RATHIN ENTERPRISES

M/S DEY ENTERPRISE

CONSTRUCTION SHELTER

M/S. NARENDRA KUMAR GARG