Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹55.4 CrAccepted-Finance KANNUR | KERALA | 670001 | ₹55.4 Cr | 1 | Accepted-Finance L1 |
| 2 | 2₹57.0 CrRejected-Finance | ₹57.0 Cr | 2 | Rejected-Finance L2 |
Tender Value
₹53.5 Cr
EMD Value
₹5 L
Closing Date
24 Sept 2024, 11:15 amClosed
Chief Engineer, KIIDC
Parvathy, tc 36/1, nh 66 bypass service road, eanchakkal jn, chackai p.o., thiruvananthapuram 695024
Comprehensive Development of Muzhappilangad and Dharmadam Beach in Kannur District
2024_KIIDC_686146_1
IRR/KIIDC/TR/5036/2023_5_1_1/1
Open Tender
Civil Works - Others
450 days
kannur
Please refer tender document
4 documents required · 4 mandatory
₹19,518
₹5 L
KIIDC Office, Trivandrum
2 Dec 2024
16 Aug 2024
27 Sept 2024
16 Aug 2024
24 Sept 2024
16 Aug 2024
22 Aug 2024
Amount
Appendix A - Demolishing and dismantling existing structure
2.33.1:Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 30 cm girth up to and including 60 cm girth
15.9.2:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar
Appendix B- Retaining wall and Ramp
2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared
2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil
2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil
2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
OD12845/2023-2024:Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification.
16.78.1:Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30
13.65.1:Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work
11.26.1:Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick
10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)
4.20.1.2:Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note : 1) Excess /less cement used than specified in this item is payble / recoverable separately.M-15 grade plain cement concrete (cement content considered @ 220 kg/cum)
OD13346/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer -
OD27920/2023-2024:Providing and laying in position machine batched and machine mixed design mix M40 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge . All works above plinth level upto floor V level
OD13843/2023-2024:Supplying and placing high corrossion resistant steel (HCR) for RCC work including straightening g<br>,cutting,bending ,placing in position and binding all complete .HCR bars of grade Fe<br>500d or more- "
5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
60.6:PVC WEEP HOLES- Providing weep holes using 75mm dia. PVC pipes working pressure 4kg /sq.cm including cost of materials, conveyance, labour charges etc. complete.
Appendix C- Storm water drains
2.10.1.2:Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia
4.1.4:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 )1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)
5.33.2:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level
5.34.1:Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).
5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
13.44.1:Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)
10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
OD12955/2023-2024:Supplying and placing high corrossion resistant steel (HCR) for RCC work including straightening g<br>,cutting,bending ,placing in position and binding all complete .HCR bars of grade Fe<br>500d or more- Upto plinth level"
5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level
19.36.2:Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.600 mm dia RCC pipes.
19.36.1:Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.450 mm dia RCC pipes.
Appendix D - Grass patch, Trees, Benches, Rubbish bin, Signage
30.2.13:Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).
OD13604/2023-2024:"Tree planting in M20grad cast in situ concrete box: Preparing tree tranch with drainage cell coverd with geotextile membrain, filling base with river washed sand upto 250mm, Filling with soil mixture of red garden soil upto 650mm, adding farmyard manure at 4:1 ratio. Cost including internal transport, application of fertilizers and chemicals (@ 20 gms/pit/sqmt), internal transportation of plants, planting the plants etc., for complete item of work (excluding cost of plant material, fertilizers and chemicals (@ 20 gms / pit/ sqmt) (Red garden soil in this context it is defined as sandy loamy garden soil congenial for plant growth which shall be of light textured, crystalline, porous and friable, fertile, slightly acidic or neutral) (As per Detail drawing) "
OD13151/2023-2024:Providing and fixing Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and even, watering with sprinkler
30.2.14.1:Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 1.2 m dia and 1.2 m deep
OD13153/2023-2024:Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge.
OD13154/2023-2024:Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
OD13155/2023-2024:Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.
OD13157/2023-2024:Providing and displaying of Rhapis palm specimen plant, having ht. 1.50 m to 1.65 m with 40 to 50 lush green suckers, well developed, fresh & healthy foliage leaves in 40 cm size of Earthen Pot/Chali/Tray & as per direction of the officer-in-charge.
OD13158/2023-2024:Providing and stacking of Jatropha multifida (red colour) of height 60-75 cm. multibranched in p.bag of size 25 cm as per direction of the officer-in-charge.
OD13600/2023-2024:Providing and stacking of Saraca indica (Sita Ashok) of height 105-120 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
OD13159/2023-2024: Providing and stacking Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
OD13160/2023-2024:Providing and stacking of Hamelia patens of height 90-105 cm. bushy in big size HDPE bags as per direction of the officer-in-charge.
OD13161/2023-2024:Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs,herbs, edge, flower beds, foliages, creepers etc. including hoeing pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by officer-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide, lawn mover and brush cutter with fuel & other T & P material/articles shall be provided by the department.)
OD13185/2023-2024:Supplying, fitting, fixing seating benches of size 2.7x 0.45 m, floor mounted FRC bench with reused wooden top and precast planter box (As per suggestion of vendor/ architect/ engineer in charge) including cost of transport, labour charges,etc,. Complete
OD13187/2023-2024:"Supplying SS Dustbins(6 Bins in each set) Double Cylinder (Duo) made of 18 gauge, SS-202 grade stainless steel hairline finish of size width 400 mm external dia., length 750 mm and height 750 mm with 2 nos. 300 mm diameter round openings at top with PU coating and Neoprene gasket ring at bottom. The dustbin should have removable cover and provision for clipping poly bags complete as per design and directions of Engineer in-charge. The dustbin shall display sticker indicating type of garbage and the top shall be finished with approved shade of PU coating as per the instructions of Engineer-incharge inclusive of testing charges if any and transportation to site"
OD13188/2023-2024:"Supplying SS Dustbins(3 Bins in each set) Double Cylinder (Duo) made of 18 gauge, SS-202 grade stainless steel hairline finish of size width 400 mm external dia., length 750 mm and height 750 mm with 2 nos. 300 mm diameter round openings at top with PU coating and Neoprene gasket ring at bottom. The dustbin should have removable cover and provision for clipping poly bags complete as per design and directions of Engineer in-charge. The dustbin shall display sticker indicating type of garbage and the top shall be finished with approved shade of PU coating as per the instructions of Engineer-incharge inclusive of testing charges if any and transportation to site "
OD13190/2023-2024:Supply & installation of Contemporary marine grade polysteel modular GAZEBO, as specified in the drawings and instructions by Engineer In Charge, self coloured, textured surface finish with scratch resistant aliphatic grade UV stabilized polyurethane paint; Inner frame work made of mild steel hot dip galvanized; All hardwares are to be of stainless steel. To be individually hand crafted to replicate steel and cast iron and to be installed with ground using foundation bolts.
OD13191/2023-2024:Integral Single/Double sided LED Signage Type 1/Type 2) with extruded aluminium hag incorporate LEDs, driver, battery and other accessories as per dimensions and design shown in technical drawings, Matter is laser engraved on acrylic sheet. Chain is provided for pendent mounting for direction purpose of approved make
16.92:Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10 mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge
16.87.1:Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-charge.With granite stone of area less than 0.50 sqm.
16.69:Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)
OD13209/2023-2024:Supplying, Providing and fixing Cast Iron grating for drain. Including carriage, labour charges, etc complete
16.90:Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.
50.18.9.7.1:Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm2
50.18.9.9.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2
50.18.9.5.2:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints compete as per direction of Engineer in Charge. 40 mm dia 6 Kgf/cm2
OD13622/2023-2024:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 90mm 6 Kg/ cm2 dia
OD13623/2023-2024:Providing and fixing Pressure gauge including the cost of fittings
OD13624/2023-2024:Providing and fixing Air valve 1' including the cost of fittings
OD13625/2023-2024:Providing and fixing Disc Filter 120 mesh 2" including the cost of fittings
OD13626/2023-2024:Providing and fixing Gravel filter having 30*2 Cum including the cost of fittings
OD13627/2023-2024:Providing and fixing Pvc flush valve 1.25 mm including the cost of fittings complete as per the direction of the Engineer in charge
OD13628/2023-2024:Providing and fixing 16*17 reducer including the cost of fittings complete as per the direction of the Engineer in charge
OD13629/2023-2024:Providing and fixing 16mm elbow including the cost of fittings complete as per the direction of the Engineer in charge
OD13630/2023-2024:Providing and fixing 16mm endcap including the cost of fittings complete as per the direction of the Engineer in charge
OD13631/2023-2024:Providing and fixing 16mm tee including the cost of fittings complete as per the direction of the Engineer in charge
OD13632/2023-2024:Providing and fixing 16mm nipple including the cost of fittings complete as per the direction of the Engineer in charge
OD13633/2023-2024:Providing and fixing 17mm nipple including the cost of fittings complete as per the direction of the Engineer in charge
OD13634/2023-2024::Providing and fixing Start nipple 16mm including the cost of fittings complete as per the direction of the Engineer in charge
OD13636/2023-2024:Providing and fixing subsurface pc 16mm 40cmc/c 2lph including the cost of fittings complete as per the direction of the Engineer in charge
OD13637/2023-2024:Providing and fixing subsurface pc dripper 16mm 30cmc/c 600mlph including the cost of fittings complete as per the direction of the Engineer in charge
OD13638/2023-2024:Providing and fixing Irrigation pipe 16mm including the cost of fittings complete as per the direction of the Engineer in charge
OD13640/2023-2024:Providing and fixing ventury system including the cost of fittings complete as per the direction of the Engineer in charge
OD13643/2023-2024:Providing and fixing Rubber grommet including the cost of fittings complete as per the direction of the Engineer in charge
OD13644/2023-2024:Providing and fixing SINGLE PHASE CONTROLLER W/DOUBLE RELAY including the cost of fittings complete as per the direction of the Engineer in charge
OD13645/2023-2024:Providing and fixing SOLAR PANEL KIT FOR RTU including the cost of fittings complete as per the direction of the Engineer in charge
OD13646/2023-2024:Providing and fixing RTU including the cost of fittings complete as per the direction of the Engineer in charge
OD13647/2023-2024:Providing and fixing Cellular Antenna Cable 10m including the cost of fittings complete as per the direction of the Engineer in charge
OD13648/2023-2024:Providing and fixing transmission Antenna 433MHz including the cost of fittings complete as per the direction of the Engineer in charge
OD13649/2023-2024:Providing and fixing MCU WITH DO TILE including the cost of fittings complete as per the direction of the Engineer in charge
OD13650/2023-2024:Providing and fixing subscription and CLOUD SERVICES- 1 YEAR PLAN or equivalent including the cost of fittings complete as per the direction of the Engineer in charge
OD13651/2023-2024:Providing and fixing D 51P PL G 2*2 BFV BSP 3WNC AQAC or equivalent including the cost of fittings complete as per the direction of the Engineer in charge
OD13655/2023-2024:Providing and fixing 1KVA SERVO STABLIZER INBUILT 440/220V,200VA ISOLATION TRANSFORMER or equivalent including the cost of fittings complete as per the direction of the Engineer in charge
OD13658/2023-2024:Providing and fixing WM WSTSB BYO 3" BS EV 10L MID or equivalent including the cost of fittings complete as per the direction of the Engineer in charge
OD13659/2023-2024:Providing and fixing S100CI 2" A BSP QRV MPG 2W C (Mainline Safety Valve) or equivalent including the cost of fittings complete as per the direction of the Engineer in charge
OD13660/2023-2024:Providing and fixing AQUATIV DC (CV 606) SINGLE UNIT or equivalent including the cost of fittings complete as per the direction of the Engineer in charge
OD13661/2023-2024:Providing and fixing AQUANET PLUS 2" AC BSP ANGLE P.R.V. or equivalent including the cost of fittings complete as per the direction of the Engineer in charge
Appendix E - Toilet block
17.81:Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.
OD28141/2023-2024:SITC of European style water closet for specially abled person toilet confirming to green building flow requirement and including following. Approved model by arch and client and confirming to green building and technical specification, and other accessories as follows: Vitreous European Floor Mounted 'P' trap W.C pan (color as per Arch and owner) (Model No: ) Anti Bacterial plastic solid closing seat and seat cover with plastic (thermoset or polyproylen) hinges & rubber buffers etc. (Model No: ) Necessary pipe connection WC connector to UPVC soil pipe. Cast iron chair with two coat of primer and one coat of approved paint to fix the Water closet to wall or on floor with approved quality Fasteners like bolts, nuts, Etc all other accessories to complete the installation. 100 dia PVC connector pipe from P or S trap with rubber bush, connector pipe to the junction of the soil stack or drain with or without vent connection arrangement ITC of approved make of Grab Bar with all require screws accessories etc to complete the work & finishing. confirming to technical specification. All other materials and labour to complete the work by contractor (Including providing and fixing all accessories, P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe of required length and proper connection to C.I. / PVC pipe etc. )complete as per specifications as per the directions of Engineer-in-charge.
17.80:Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx.size 610x390x370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer - in-charge.
OD28145/2023-2024:SITC of CP brass / S.S. twin coat hook, fixed to wall / door with concealed CP screws etc.
17.34.1:Providing and fixing toilet paper holder:C.P. brass
18.22.1:Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:100 mm diameter
17.71:Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms
OD28160/2023-2024:Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete
17.7.1:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
17.16A:Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge
17.32.4:Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm
OD13245/2023-2024:Providing and fixing HPL Waterproof Toilet Partition, Size: 4 Ft x 6 Ft x 7 Ft, thickness : 12mm including all the fixing accessories and as per approved shade amd colour from Architect/ Client
17.73.1:Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms
9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood
9.5.1.1:Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge. Second class teak wood35 mm thick shutters
9.147B.1:543 SUB HEAD : 9 - WOOD & PVC WORK 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)
6.3.2:Brick work with common burnt clay machine moulded perforated bricks of classdesignation 12.5 conforming to IS: 2222 in superstructure above plinth level up tofloor five level in cement mortar 1:6 (1 cement : 6 coarse sand):With Modular bricks
13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)
13.82.2:Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats
6.47:Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
13.11:18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 ( 1 cement : 6 fine sand).
11.36:Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.
18.16.1:Providing and fixing brass stop cock of approved quality :15 mm nominal bore
18.15.1:Providing and fixing brass bib cock of approved quality :15 mm nominal bore
OD13438/2023-2024:SITC of approved make of Shower consisting of 2 in 1 wall Shower Mixer and Diverter, along with the bib tap with all required piping, screws, accessories etc to complete the work & finishing. confirming to technical specification.: (Model No: )
50.18.9.1.2:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 15 mm dia 10Kgf/cm2
50.18.9.2.2:Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm dia 10 Kgf/cm2
50.18.9.3.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 25 mm dia 12Kfg/cm2
50.18.9.4.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.32 mm dia 10.Kgf/cm2
50.18.9.5.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge 40 mm dia 10Kgf/cm2
50.18.9.6.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 10Kgf/cm2
OD13443/2023-2024:SITC of approved make brass air release valve including providing and fixing cut-off valve all fitting and accessories, etc. and as per specification.
17.60.2.1:Providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 75 mm outletSand cast iron S & S as per IS - 3989
17.28.1.1:Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete. Semi rigid pipe32 mm dia
17.28.1.2:Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete. Semi rigid pipe40 mm dia
OD28163/2023-2024:Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete. Semi rigid pipe 75 mm dia
OD13448/2023-2024:SITC of UPVC SWR Pipes of TYPE B confirming to IS:13592-1992 and fittings confirming to IS:14732-1999 for SOIL AND WASTE including all fittings and with inspection doors, including supports brackets as per supplier specification and distance, etc. laying pipe in wall and slabs including all require supports, testing as mentioned in technical specification, Chiselling, making good with chicken / fiber mesh and paper coat with cement mortar the walls and floors wherever required complete with Cement Solvent joint. 110 mm dia
OD13449/2023-2024:SITC of UPVC SWR Pipes of TYPE B confirming to IS:13592-1992 and fittings confirming to IS:14732-1999 for SOIL AND WASTE including all fittings and with inspection doors, including supports brackets as per supplier specification and distance, etc. laying pipe in wall and slabs including all require supports, testing as mentioned in technical specification, Chiselling, making good with chicken / fiber mesh and paper coat with cement mortar the walls and floors wherever required complete with Cement Solvent joint. 75 mm dia
OD13450/2023-2024:SITC of UPVC SWR Pipes of TYPE B confirming to IS:13592-1992 and fittings confirming to IS:14732-1999 for SOIL AND WASTE including all fittings and with inspection doors, including supports brackets as per supplier specification and distance, etc. laying pipe in wall and slabs including all require supports, testing as mentioned in technical specification, Chiselling, making good with chicken / fiber mesh and paper coat with cement mortar the walls and floors wherever required complete with Cement Solvent joint. 50 mm dia
17.56.2.1:Providing and fixing terminal guard: 75 mmSand cast iron S & S as per IS - 1729
OD28167/2023-2024:Providing and fixing terminal guard: 110 mmSand cast iron S & S as per IS - 1729
OD13456/2023-2024:Supply, laying, fixing, jointing, testing and commissioning of readymade PVC Rain Water Inlets for corner/side entry Confirming to IS 3592. 75 mm dia
2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil
2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
16.78.1:Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30
13.65.1:Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work
4.20.1.2:Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note : 1) Excess /less cement used than specified in this item is payble / recoverable separately.M-15 grade plain cement concrete (cement content considered @ 220 kg/cum)
OD10739/2024-2025:Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-40 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).600 mm dia piles
OD27928/2023-2024:Providing and laying in position machine batched and machine mixed design mix M30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge . All works upto plinth level.
OD30218/2023-2024:Providing and laying in position machine batched and machine mixed design mix M30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge . All works above plinth level upto floor V level
OD14019/2023-2024:Supplying and placing high corrossion resistant steel (HCR) for RCC work including straightening g<br>,cutting,bending ,placing in position and binding all complete .HCR bars of grade Fe<br>500d or more"
5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
22.22A:Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.
10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
10.26.1:Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube
OD13742/2023-2024:Supply, installation, testing and commissioning of propeller exhaust fans with Necessary Supporting Structure & Vibration Isolation as per specifications and drawings of various capacities as given below suitable for 230 volts, 50 Hz, single phase AC supply complete with gravity Shutters and Metal clad MCB and Starter, 5 mtr of copper core cable, earth wire all complete. NC level 3 Mtr away from source should be less than 75db (Sound dB level requirement may change to 65 dB if the fans are to be installed in the habitable spaces) SITC of NO/NC Contactor provided along with the MCB inline to control the fan operation from fire alarm signal Earthing strip / 8 SWG GI wire for the fans to be provided by HVAC vendor from equipment to nearest earthing network.
OD13744/2023-2024:Supply, installation, Testing & Commissioning of LT Panel Boards /Feeder pillars. complete in all respects as per technical specifications & approval of Client / Consultant. Refer specification "LT Panel Boards made of 14 SWG powder coated sheet steel of appropriate size of IP43 Degree of Protection (as per IS: 13947 Part-I) with 'C' channels for support with single front openable doors with duly gasketed with Neoprene gaskets for all switch gears and Aluminium bus bar with heat shrinkable colored PVC Sleeves including control wiring with ferrule & duly riveted anodized aluminium labels for identification of switch gears all complete. The Switchboards shall be provided with detachable gland plates for entry of cables from the bottom. Schematic diagram shall be displayed at the LT Panel Boards front with glowing fonts. PLUMBING PANEL TYPE 1
OD13748/2023-2024:Supply, installation, Testing & Commissioning of LT Panel Boards /Feeder pillars. complete in all respects as per technical specifications & approval of Client / Consultant. Refer specification "LT Panel Boards made of 14 SWG powder coated sheet steel of appropriate size of IP43 Degree of Protection (as per IS: 13947 Part-I) with 'C' channels for support with single front openable doors with duly gasketed with Neoprene gaskets for all switch gears and Aluminium bus bar with heat shrinkable colored PVC Sleeves including control wiring with ferrule & duly riveted anodized aluminium labels for identification of switch gears all complete. The Switchboards shall be provided with detachable gland plates for entry of cables from the bottom. Schematic diagram shall be displayed at the LT Panel Boards front with glowing fonts. PLUMBING PANEL TYPE 2
OD13749/2023-2024:SITC of MS Powder coated enclosure box with suitable bush buttons (set of ON/OFF) and control wiring for operating all pumps from remote location with suitable indication.
OD13751/2023-2024:Supply, of XLPE Armoured Aluminium/Copper cables 1100 V.grade with ISI mark of following sizes, with necessary supports, clamps, etc. for internal cabling /for external cable laying or in provided pipe in an approved manner and as per site requirement. 3C x 4 Sq.mm CU ARM. XLPE cable
OD13758/2023-2024:"Supply, fabrication and erection of galvanized sheet metal ducting with TDF Flange generally as specified and completely factory fabricated with: Ducting to be done as per SMACNA standards" i) Hot dip Galvanized companion flanges girth angles. Supply and fixing of flexible duct connector between equipment and duct to avoid vibration in the ducting. ii)Turning vanes. iii) Hot dip Galvanized structural support systems. iv) Closed cell neoprene gasket.
OD13759/2023-2024:"Supply, fabrication and erection of galvanized sheet metal ducting with TDF Flange generally as specified and completely factory fabricated with: Ducting to be done as per SMACNA standards" i) Hot dip Galvanized companion flanges girth angles. Manual GI Volume control dampers as specified. ii)Turning vanes. iii) Hot dip Galvanized structural support systems. iv) Closed cell neoprene gasket.
OD13760/2023-2024:"Supply, fabrication and erection of galvanized sheet metal ducting with TDF Flange generally as specified and completely factory fabricated with: Ducting to be done as per SMACNA standards" i) Hot dip Galvanized companion flanges girth angles. (22 SWG) galvanized Sheet- (751 to 1500mm Length) ii)Turning vanes. iii) Hot dip Galvanized structural support systems. iv) Closed cell neoprene gasket.
OD28171/2023-2024:Wall mounted air-cooled split air conditioning units (Indoor and ODU) with Ozone friendly refrigerant as described in specifications. The unit shall be complete with decorative type fan coil unit and external condensing unit, complete in all respects, inclusive of copper refrigerant piping, refnut joints, CPVC condensate drain piping, valves and insulation quoted price shall include cost of cooling thermostat, power wiring, control wiring and earthing. The unit capacities shall be as follows: Note : Fins and copper tubes of Air Cooled Condenser along with copper tubing / piping with all joints and U-Bends exposed to coastal areas corrosive atmosphere / aggressive ambient, shall be painted with special corrosion prevention coating either in factory or at site. The AC unit shall be provided with standard kit (3mtr length) of refrigerant piping and cable. Serving space - server room
OD29447/2023-2024:SITC of approved quality Motorised Butterfly valve, Differential Pressure : 0.5 to 10 bar confirming to IS 9334. with require electrical supply and operating on the signal received from level controller attached to the tank, including all internal cabling piping require for following sizes (for over head tanks)50 mm
OD29448/2023-2024:SITC of approved quality Motorised Butterfly valve, Differential Pressure : 0.5 to 10 bar confirming to IS 9334. with require electrical supply and operating on the signal received from level controller attached to the tank, including all internal cabling piping require for following sizes (for over head tanks)40 mm
50.18.8.5.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 40 mm pipe 6Kgf/cm2
50.18.8.6.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2
50.18.8.7.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2
50.18.8.8.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2
50.18.8.9.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2
50.18.9.16.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall
50.18.9.18.1:Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall
50.18.9.19.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall
18.8.2:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes
18.8.3:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes
18.8.4:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes
OD11046/2024-2025:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.40 mm nominal outer dia pipes
18.7.3:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes
18.7.4:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes
18.7.5:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes
18.7.6:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes
18.9.6:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work50 mm nominal outer dia pipes
18.9.7:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work62.50 mm nominal inner dia pipes
18.9.8:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work75 mm nominal inner dia pipes
18.9.9:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work100 mm nominal inner dia pipes
OD11057/2024-2025:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement. 110 mm dia Y Make:Astral/Equivalent
50.18.9.22.1:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow
50.18.9.22.2:Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow
50.18.9.22.3:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow
50.18.9.22.5:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee
50.18.9.22.6:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee
50.18.9.22.8:Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl
OD11058/2024-2025:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement. 75 mm dia Y Make:Astral/Equivalent
50.18.9.22.11:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling
50.18.9.21:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow
50.18.9.21.2:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia 45 degree Elbow
50.18.9.21.3:Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow
50.18.9.21.5:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee
50.18.9.21.6:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75x75x75 mm dia Door Tee
50.18.9.21.7:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl
50.18.9.20.1:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow
50.18.9.20.2:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow
50.18.9.20.5:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee
50.18.9.20.9:Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling
OD11059/2024-2025:Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement. 63 mm dia Y Make:Astral /Equivalent
OD11060/2024-2025:Providing , fixing , testing and commissioning pvc multy inlet (110x75x50x50x50) floor trap of self cleansing design with or without vent arm complete, including cost of masonry or concrete supports cutting and making good the walls and floors where ever required.
OD11061/2024-2025:Providing , fixing , testing and commissioning pvc "P" trap with multy inlet or single inlet connection of required sizes of self cleansing design with or without vent arm complete, including cost of masonry or concrete supports cutting and making good the walls and floors where ever required. Make: Astral /Equivalent
OD11063/2024-2025:Providing and fixing 40 mm dia PVC Pasted Valve
OD11064/2024-2025:Providing and fixing 32 mm dia PVC Pasted Valve
OD11065/2024-2025:Providing and fixing 25 mm dia PVC Pasted Valve
17.23:Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.
OD11067/2024-2025:Providing and fixing of C.P urinal push cock of approved quality
OD11068/2024-2025:Providing and fixing push plate square chrome, wall hung, concealed cistern with half frame of approved quality
50.18.9.21.9:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling
Appendix F- Water supply and plumbing
2.10.1.1:Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soilPipes, cables etc, not exceeding 80 mm dia
4.20.1.1:Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note : 1) Excess /less cement used than specified in this item is payble / recoverable separately. All works upto plinth level:M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)
18.34.1:Constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
19.9.1.2:Constructing brick masonry circular type manhole 0.91 m internal dia at bottam and 0.56 m dia at to[ in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix ( 1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size ), and making necessary channel in cement concrete 1:2:4 ( 1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design:With Sewer bricks conforming to IS:4885
19.15.1:Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) as per standard design.With 20x20 mm square bar
18.33.1:Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement:4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5
OD13688/2023-2024:"Providing and supplying in standard lengths Polyethelene Pipes (HDPE), confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. As per IS:4984-2016, the pipes upto 90 mm dia. should be supplied in coil form only. PN 6"
OD13689/2023-2024:"Providing and supplying in standard lengths Polyethelene Pipes (HDPE), confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. As per IS:4984-2016, the pipes upto 90 mm dia. should be supplied in coil form only. PN 6"
OD13690/2023-2024:Lowering,Laying and Jointng HDPE/MDPE pipes in proper position including all specials by compression fitting/electrofusion and butt fusion jointing procedure as per relevant IS code complete with all materials for jointing procedure like Electrofusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS 7634 Part II .90 mm
OD28200/2023-2024:Lowering,Laying and Jointng HDPE/MDPE pipes in proper position including all specials by compression fitting/electrofusion and butt fusion jointing procedure as per relevant IS code complete with all materials for jointing procedure like Electrofusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS 7634 Part II. 110 mm.
OD13691/2023-2024:Hydraulic testing of HDPE/MDPE pipe line to specified pressure including cost of all materials and labour and water for testing for specified length including cutting, placing end cap making arrangement for filling safe water using reciprocating type pumps which should be able to provide specified test pressure gauges and other necessary equipments, labour, operation charges etc. required for testing. The rate under this item shall also include cost of retesting, if necessary and reinstating to original position.
OD13692/2023-2024:Providing double flange sluice valve conforming for IS 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & OM in all respect etc. complete. 100 mm
OD28202/2023-2024:Providing double flange sluice valve conforming for IS 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & OM in all respect etc. complete. 80 mm
OD13693/2023-2024:Supply, installation, testing & commissioning of Hydro-pneumatic system with vertical inline Multistage booster centrifugal SS - 316L pump-motor sets, suitable for operation on solar and hybrid, pneumatic balancing tank, mounting skid, foot valves, G.I. suction & discharge pipes, fittings, cast brass / virgin brass valves, C.I. Strainers ar suction head, etc. Each pump shall have phase electric motor. Includes pressure switches, VFD based control panel with starters, protections, relays, cables, interlocking with level & pressure switches. Suction / Delivery Piping all connections, etc complete for domestic supply as directed by Engineer in charge
OD13694/2023-2024:Providing and supplying in standard length (PE material) HDPE Double wall corrugated pipe for non pressure underground drainage and sewerage with smooth internal & corrugated external surface confirming to IS 16098:Part 2 2013 with spigot or plain end with necessary jointing material coupler excluding all statutary duties and taxes such as GST levied by GoI and GoM in all respect, transportation and frieght charges, inspection charges, loading and unloading charges conveyance to departmental store/site and stacking the same in closed shade duly protecting from direct sun ray and rains etc. complete (CL SN8)- (Considered 10 % increase in length for wastage)
3.4:Cement mortar 1:4 (1 cement : 4 fine sand).
OD13697/2023-2024:MBBR technology for wastewater treatment including pre-treatment with screening, equalization, secondary treatment with biological treatment, tube settlers, disinfection, sludge disposal and tertiary treatment with sand media filter and activated carbon filter. (44 kLD)
OD13698/2023-2024:Providing and supplying in standard lengths Polyethelene Pipes (HDPE), confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. As per IS:4984-2016, the pipes upto 110 mm dia. should be supplied in coil form only.
OD13700/2023-2024:Providing and fixing CI sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately):
OD28203/2023-2024:R.O. based Water Treatment Plant plant with dual media filter, antiscalant dosing system and Reverse Osmosis system
OD28208/2023-2024:Providing and supplying in standard lengths ISI mark rigid unplasticised PVC pipes suitable for potable water with solvent cement joints including cost of couplers, as per IS specification no. 4985 / 1988 excluding GST levied by GOI and GOM in all respect, including transportation, freight charges, inspection charges, loading, unloading, conveyance to the departmental stores and stacking the same in closed shed duly protected from sun rays and rains including cost of jointing material i.e. solvent cement, etc. complete (selffit type to be jointed with cement solvent).-Working Pressure 6 Kg. / Sq.cm. 90 mm dia
OD28212/2023-2024:Lowering, laying and jointing with P.V.C. pipes and specials of following class and diameter including cost of conveyance from stores to site of works including cost of all labour, material, except cement solvent, rubber ring, as per IS code, etc. complete (with cement solvent joint / ring fit joint).
OD28213/2023-2024:Hydraulic testing of PVC pipe line to specified pressure including cost of all materials and labour and water for testing for specified length including cutting, placing end cap making arrangement for filling safe water using reciprocating type pumps which should be able to provide specified test pressure gauges and other necessary equipments, labour, operation charges, etc. required for testing. The rate under this item shall also include cost of retesting, if necessary and reinstating to original position.
Appendix G- Kiosk/ Promenade/ Sea wall
2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil
2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
OD28234/2023-2024: Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete."
16.78.1:Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30
OD30209/2023-2024:Supply and Installation of Geo Mat for sea wall- The geo mat must be of a non woven&lt;br&gt;composite material. The composite must be of a laid geogrid made of stretch monolithic polypropylene (PP)&lt;br&gt;flat bars with welded junctions and mechanical bonded filter geotextile welded within the geogrid structure.&lt;br&gt;Joins of geomats must have an overlap of not less than 1.5 metres. The Contractor must submit details of&lt;br&gt;the fixing and joining arrangements of the geomats to be approved by the Engineer. Outer edges of the&lt;br&gt;geomats must be hemmed using high strength nylon. Temporary fixing of the geomat is required and the&lt;br&gt;Contractor must submit details of this for approval by the Engineer.
16.96:Providing & making Gabion structure with Mechanically Woven Double Twisted Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH Clause 2500, of required size, Mesh Type 10x12(D=100 mm with tolerance of ±2%), Zinic+10%Al alloy+PVC coated, Mesh wire diameter 2.7/3.7mm (ID/OD),mechanically edged/selvedged with partitions at every 1m interval and shall have minimum 10 numbersof openings per meter of mesh perpendicular to twist, tying with lacing wire of diameter2.2/3.2mm(ID/OD), supplied @3% by weight of Gabion boxes, filled with boulders with least dimension of 200 mm, as per drawing, all complete as per directions of Engineer-in-charge
4.20.1.2:Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note : 1) Excess /less cement used than specified in this item is payble / recoverable separately.M-15 grade plain cement concrete (cement content considered @ 220 kg/cum)
OD10753/2024-2025:Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-40 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc.by DMC method all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).700 mm dia piles
OD28238/2023-2024:Providing and laying in position machine batched and machine mixed design mix M40 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge . All works above plinth level upto floor V level
OD14020/2023-2024:Supplying and placing high corrossion resistant steel (HCR) for RCC work including straightening g<br>,cutting,bending ,placing in position and binding all complete .HCR bars of grade Fe<br>500d or more- "
5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
12.1.1:Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m2
12.26.1:Providing and fixing plain Multipurpose Cement board (High Pressure steam cured) as per IS : 14862, with suitable screws for fibre cement board in ceiling etc. complete (frame work to be paid separately) :6 mm thick cement board
11.23.1:Marble stone flooring with 18 mm thick marble stone as per sample of marble approved by Engineer-in-Charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with:Makrana white second quality
9.6.3:Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS: 14616 and TADS 15:2001 (Part B), including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-in-Charge and panelling with panels of:12 mm thick one side Pre- laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - I medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-I conforming to IS : 3087 bonded with BWP types synthetic resin adhesive as per IS : 848 and pre - laminated conforming to IS : 12823 Grade - I, Type II marked:
22.22A:Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.
20.6.2.1:Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge. Single pile above 50 tonne and upto 100 tonne capacityInitial test
OD28239/2023-2024:Providing Steel Liner 6 mm thick for Steining including Fabricating and Setting out as per Detailed Drawing. (Morth 12.22)
60.7.8:DR with Departmental. Stone - DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course using departmental rubble including packing to compactness to lines and levels, labour charges etc. complete as per direction of Departmental officers at site
OD11828/2024-2025:Supplying and laying Armour layer using 300 kg to 500 kg blasted granite<br>stones of specific gravity not less than 2.65 as per approved design including supply of stones , sorting at<br>quarry, loading from quarry , conveying to site in tipper , weighing on Weigh Bridge established at site by<br>the contractor(Certified by Legal Metrology), Installation of PC loaded with software approved by the<br>Departmental officers for measurement , unloading , dumping at site to lines and levels, rehandling stones<br>for forming the section with the help of tippers and suitable crane and packing of stones including hire and<br>operational charges of all tools and plants and all sundry expenses , providing and maintaining the runway<br>for movement of vehicles, crane using spalls gravel or sand etc. complete as per the direction of<br>departmental officers at site
OD11833/2024-2025:Supplying and laying Core layer using 1 kg to 10 kg blasted granite<br>stones of specific gravity not less than 2.65 as per approved design including supply of stones, sorting at<br>quarry,loading from quarry , conveying to site in tipper/lorry , weighing on Weigh Bridge established at site<br>by the contractor(Certified by Legal Metrology), Installation of PC loaded with Software approved by the<br>Departmental officers for measurement , unloading , dumping at site to lines and levels, rehandling stones<br>for forming the section with the help of tippers and suitable crane/hydraulic excavator/manually and packing<br>of stones including hire and operational charges of all tools and plants and all sundry expenses , providing<br>and maintaining the runway for movement of vehicles, crane using spalls gravel or sand etc. complete as per<br>the direction of departmental officers at site.
Appendix H - Kids Play Equipments
OD13434/2023-2024:Supply. Delivery and fixing in position of slide with ladder and double swings(fibre slide 10Ft) power, the slide is fabricated and covered with fibre along with FRP with pigment body including all cost, conveyance of materials and all labour charges etc. complete as directed by the Departmental authorities.
OD13436/2023-2024:Supplying and fixing Garden swing using best quality equipment,cost and conveyance of all<br>materials,labour etc complete<br>
OD13437/2023-2024:Supplying and fixing spiral slide using best quality equipment ,cost and conveyance of all materials,labour<br>charges etc complete
Appendix I - Parking area and parking renovation
16.1:Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.
16.91.1:Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
16.69:Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)
30.2.1:Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
30.2.2:Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).
30.2.4.1:Supplying and stacking at site dump manure from approved source, including carriage upto 5 k.m. lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm
30.2.5:Rough dressing the trenched ground including breaking clods.
30.2.6:Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.
30.2.7:Fine dressing of the ground
30.2.8:Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
30.2.9:Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
30.2.13:Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).
30.2.14.1:Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 1.2 m dia and 1.2 m deep
2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
OD29568/2023-2024:Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - All works above plinth level upto floor V level
OD29583/2023-2024:Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement contentin design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M15 grade with minimum cement content of 240 kg /cum.
OD29584/2023-2024:Supplying and placing high corrossion resistant steel (HCR) for RCC work including straightening g<br>,cutting,bending ,placing in position and binding all complete .HCR bars of grade Fe<br>500d or more- "
5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts
5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform
5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers
2.1.1:Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil
OD29590/2023-2024:Disposing of excavated stuff of any kind from site to any place which is with in a lead of 5 km as directed by Engineer in charge. Etc. completed.
16.11:Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.
13.44.1:Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)
10.16.2:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes
12.1.2:Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating less than 275 gm/m2
2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
60.7.4:DR PACKING FOR APRONS - Rough stone dry packing for apron with good quality blasted rubble including packing to compactness to lines levels, cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site
4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level
5.33.2:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level
6.2.1:Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)
6.3.2:Brick work with common burnt clay machine moulded perforated bricks of classdesignation 12.5 conforming to IS: 2222 in superstructure above plinth level up tofloor five level in cement mortar 1:6 (1 cement : 6 coarse sand):With Modular bricks
Appendix J - Electrical work
1.14.2:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
1.14.3:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire
1.17.12:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm
2.3.2:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way, Double door
2.3.3:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12 way, Double door
2.11:Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
2.12.1:Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps
2.10.1:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole
2.10.3:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole
2.10.4:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole
2.13.1:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps
2.14.2:Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps
2.15.2:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps
2.13.2:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps
2.15.3:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps
2.16:Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.
90.11.1.10:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - three phase double cover (IP 42/43)
90.11.1.14:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)
2.23.1:Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. 2For 6 way, Double door SPN MCBDB
2.24.1:Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 4 way, Double door TPN MCBDB
2.24.3:Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 8 way, Double door TPN MCBDB
90.12.9.3:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench63/50 mm or nearest size
14.14.2:Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.150 mm dia
14.14.4:Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.300 mm dia
OD13746/2023-2024: Supply installation testing and commissioning of 8 Metre height decorative pole made of mild steel/steel tube having suitable thickness The base section of Pole shall have an in-built junction box to accommodate a heavy duty connector for loop‐in and loop‐out of UG cable and provision for fixing MCB with anti‐theft lock arrangement. The Pole shaft should be fabricated out of Steel tube of grade YST 240. Structurally designed base plate of Steel A36/A572-50 or equivalent should be welded with the pole shaft. The pole shall be designed as per EN40 for withstand basic wind speed of 169kmph. The complete structure should be hot dip galvanised and marine grade treated. Base plate fixing in existing foundation with bolt and all accessories as required. (Excluding civil foundation) .Make: KESSLEC HDGI NEMO or equivalent
OD13740/2023-2024:Supply and fixing of 3 W spike light, in pressure dies cast aluminium lighting, IP 65 rated
OD13815/2023-2024:SITC of 250W LED flood light , die cast aluminum housing toughened glass in the front and peanut lens for batwing light distribution. IP rating >66 ,
1.10.3:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C
1.55.3:Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C
1.21.2:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm
1.24.1:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch
1.24.4:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet
1.27.1:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)
1.27.2:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)
1.27.4:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)
1.32:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch
1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet
1.33:Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.
OD31464/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 4 C 16 sqmm XLPE Al
OD10894/2024-2025:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 300 sqmm XLPE Al
OD31407/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 185 sqmm XLPE Al
OD31442/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 150 sqmm XLPE Al.
OD31441/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 120 sqmm XLPE Al
OD31468/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 95 sqmm XLPE Al
OD31467/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 50 sqmm XLPE Al
OD31466/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 35 sqmm XLPE Al
OD31465/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 25 sqmm XLPE Al
OD31463/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3 C 35 sqmm XLPE Al
OD31462/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3 C 25 sqmm XLPE Al
OD31474/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3 C 16 sqmm XLPE Al
OD31473/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 2 C 10 sqmm XLPE Al
OD31472/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Copper power cable of 1.1 KV grade of following sizes as required 4C 6 sqmm XLPE Cu
OD31471/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Copper power cable of 1.1 KV grade of following sizes as required 4C 4 sqmm XLPE Cu
OD31470/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Copper power cable of 1.1 KV grade of following sizes as required 3C 6 sqmm XLPE Cu
OD31469/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Copper power cable of 1.1 KV grade of following sizes as required 3C 4 sqmm XLPE Cu
7.7.1:Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)
7.5.1:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm
7.5.2:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 35 sq. mm and upto 95 sq. mm
7.5.3:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 95 sq. mm and upto 185 sq. mm
7.5.4:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 185 sq. mm and upto 400 sq. mm
9.1.2:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 10 sq. mm (19mm)
9.1.8:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 16 sq. mm (25mm)
9.1.9:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 25 sq. mm (25mm)
9.1.10:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 35 sq. mm (28mm)
9.1.20:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)
9.1.21:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)
9.1.22:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)
9.1.24:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)
9.1.25:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)
9.1.26:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)
9.1.27:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)
9.1.30:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)
9.1.33:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)
OD31476/2023-2024:Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required.4C 6 sqmm .
OD31481/2023-2024:Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 4C 4 sqmm
OD31479/2023-2024:Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 3C 4 sqmm
OD31480/2023-2024:Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 3C 6 sqmm
90.6.5.11:Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.3 core 1.50 sq mm
OD10871/2024-2025:OD : Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required 300 MM WIDTH X 50 MM DEPTH X 2 MM THICKNESS
OD10872/2024-2025:OD: : Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required 200 MM WIDTH X 50 MM DEPTH X 2 MM THICKNESS
OD10874/2024-2025:OD: : Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required 100 MM WIDTH X 50 MM DEPTH X 2 MM THICKNESS
90.6.5.20:Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.4 core 4.00 sq mm
OD31485/2023-2024:Supplying and providing of maintenance free earthing system comprises of molecularly bonded copper of 99.9% purity on low carbon steel of min 3048mm length (10 feet), having a diameter of 20mm with copper bonding thickness of 250 microns. The Rod has to be either continuous or with self-coupling peg & bore arrangement with fault current withstand capability of 30 kA rms value for 1 second and I peak of 76 kA. The rod must be having corrosion test, peel off test for uniform coating, 180 degree bend test with out peel off of copper bonding. Exothermic welded clamp for clamping as suggested as per NBC 2016. Ordinary stainless steel/Copper alloy universal clamps are not recommended. For self coupling peg & bore arrangement rod needs Impact point on the bottom rod for easy insertion. Earth enhancing mineral compound is used for improving the soil conductivity. The material shall be mineral inert to sub soil and shall not pollute the environment and non corrosive to earth rod. The material should have a resistivity less than 0.2 Ωm. It should be free from hazardous substances. The mineral compound is required to have minimum 17.5 Kg of the total composite. The compound should be chemically inert. Concrete earth electrode inspection chamber with weight bearing capacity of 30kN. The dimension shall be 320mmX 320mmX 190mm. Make: Cape or equivalent
OD31488/2023-2024:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required (for horizontal run)25 x 3 mm copper strip
5.17:Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.
OD31518/2023-2024:Supply and fixing following size earth bench, fixing on surface of wall/parapet using iron screws, bench having holes for connecting earth strip/wires, making good the damages, colour washing etc as required. 25x3x400 mm Cu earth bench.
90.16.5.4:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)
OD31519/2023-2024:Supply and fixing of 450 x 450 mm SFRC Heavy duty manhole cover with frame having clear opening 450 x450 mm and outer frame size 770x770x165mm and cover size 590x590x90mm, the weight of the cover to be not less than 185kg.
90.4.6:Conveyance, installation, testing and commissioning of wall mounting fans of all types using mounting brackets supplied along with the fan.
OD31523/2023-2024:Supply of 7+/-2W LED bulkhead fitting (IP 65), housing made of die cast aluminium with 6500K colour temperature with a lumen output minimum 100lumen/Watt, CRI>80,beam angle 120 degrees, suitable for outdoor applications as required. Make -Philips or equivalent
OD31524/2023-2024:Supply of 12+/-2W LED surface mounted light fixture with IP 65, colour temperature 4000K,Lumen output minimun 100lumen/Watt, CRI>80, including all necessary accessories etc as required. Make Philips All Weather or equivalent
90.3.19.3:Supply conveyance, installation, testing and commissioning the light fittings of following types made from CRCA sheet 0.5mm thickness with all accessories and lamps directly on wall and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required1200 mm 1X20W LED Lamp with box type fixture
OD31526/2023-2024:Supply of 400mm wall mounting fan including all accessories as required. Make: Crompton or equivalent
OD31527/2023-2024:Supply , installation, testing & commissioning of of 450mm Heavy duty exhaust fan including all accessories as required. Make: Crompton or equivalent
OD31547/2023-2024:Supply of ceiling fans of the following sizes using standard accessories excluding resistance type regulator as required. 1200mm sweep size - BLDC ceiling fan ,5 star rated complete with 300mm down rod , canopies, shackles, blades and remote working on 230V/240V single phase AC. Make - Crompton or equivalent
1.25:Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
90.4.1:Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.
OD31551/2023-2024:Supply installation testing and commissioning of 3 Metre height decorative pole made of mild steel/steel tube have minimum thickness of 2.5- 3mm. The pole shall have two section, base section having length of 1metre with dia of 140mm and top section having length of 2 metre with dia of 76mm . Pole shall be mounted on square base plate of dimensions 250x250x12mm thickness. The base section of Pole shall have an in-built junction box to accommodate a heavy duty connector for loop‐in and loop‐out of UG cable and provision for fixing MCB with anti‐theft lock arrangement. The Pole shaft should be fabricated out of Steel tube of grade YST 240. Structurally designed base plate of Steel A36/A572-50 or equivalent should be welded with the pole shaft. The pole shall be designed as per EN40 for withstand basic wind speed of 169kmph. The complete structure should be hot dip galvanised and marine grade treated. Base plate fixing in existing foundation with bolt and all accessories as required. (Excluding civil foundation) .Make: KESSLEC HDGI NEMO or equivalent
OD31553/2023-2024:Supply installation testing and commissioning of 4.5 Metre height decorative pole made of mild steel/steel tube have minimum thickness of 2.5- 3mm. The pole shall have two section, base section having length of 1metre with dia of 140mm and top section having length of 3.5 metre with dia of 76mm . Pole shall be mounted on square base plate of dimensions 250x250x12mm thickness. The base section of Pole shall have an in-built junction box to accommodate a heavy duty connector for loop‐in and loop‐out of UG cable and provision for fixing MCB with anti‐theft lock arrangement. The Pole shaft should be fabricated out of Steel tube of grade YST 240. Structurally designed base plate of Steel A36/A572-50 or equivalent should be welded with the pole shaft. The pole shall be designed as per EN40 for withstand basic wind speed of 169kmph. The complete structure should be hot dip galvanised and marine grade treated. Base plate fixing in existing foundation with bolt and all accessories as required.(Excluding civil foundation). Make: KESSLEC HDGI NEMO or equivalent
OD31552/2023-2024:Supply installation testing and commissioning of 30±5W LED Decorative post top light fixture with a grey painted top made high pressure die casted aluminium and three supporting ribs made of high pressure die casted aluminium, a structured polycarbonate protector (IK08) permanently sealed with the body to achieve separate IP66 optical & IP65 control gear compartments. Suitable for post top mounting on 76mm OD diameter pipe. All hardware shall be of stainless steel for longer life. The luminaire have 3000K-5700K colour temperature, colour rendering index (CRI) >70, efficiency of luminaire shall be 100 Lm/W, suitable for outdoor applications, including all connections etc as required.Make: KESSLEC WELS or equivalent.
OD31591/2023-2024:OD : FEEDER PILLAR +STREET LIGHT PANEL Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent)- Incomer:RYBindicatorwithcontrolfuses-1set,Multifunctionmeter-1nos,100/5A CL1 5VA CT 1 set, busbar mounted surge protection device (Type-1) -1no, 100A 16kA FP TM MCCB - 1 no, Busbar: copper busbar suitable for 100A Outgoings:40A FP 40A MCB-7nos, 25A 10kA FPMCB-1nos,25A 10kA DPMCB-2nos, RYB indicator with control fuses-1set,Multi functionmeter-1nos, 40/5ACL15VACT-1set, 40A FPContactor-1no,Digital Timer -1no, Sub Outgoings: 25A FP RCBO - 16nos and all neccessories accessories as required.
OD31592/2023-2024:OD : FEEDER PILLAR C +STREET LIGHT PANEL 3 Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent)- Incomer:RYBindicatorwithcontrolfuses-1set,Multifunctionmeter-1nos,100/5A CL1 5VA CT 1 set, busbar mounted surge protection device (Type-1) -1no, 100A 16kA FP TM MCCB - 1 no, Busbar: copper busbar suitable for 100A Outgoings:40A FP 40A MCB-10nos, 25A 10kA FPMCB-2nos,25A 10kA DPMCB-4nos, RYB indicator with control fuses-1set,Multi functionmeter-1nos, 40/5ACL15VACT-1set, 40A FPContactor-1no,Digital Timer -1no, Sub Outgoings: 25A FP RCBO - 12nos and all neccessories accessories as required.
OD31594/2023-2024:STREET LIGHT PANEL Incomer: RYB indicator with control fuses - 1 set, Multi function meter - 1 nos, 32/5A CL 1 5VA CT - 1 set, busbar mounted surge protection device (Type-1) - 1no, 32A 10kA FP RCBO-1, 32A FP Contactor -1no, Digital Timer -1no Busbar: copper busbar suitable for 32AOutgoings: 16A 10kA FP MCB - 12nos and all neccessories accessories as required
OD31595/2023-2024:KIOSK SUB PANEL OD : Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent) Incomer: Busbar mounted surge protection device (Type-1) - 1no, 63A 16kA FP TM MCCB - 1 no, Busbar: copper busbar suitable for 63A,Outgoings: 40A 10kA DP MCB - 8 nos, 63A Fuse base & 40A fuse link -3nos, 40A Neutral Link-3no, Provision for fixing single phase energy meter - 6nos, and all neccessories accessories as required
OD10732/2024-2025:OD; Supply, installation testing and commissioning of 5KVA UPS 3phase input & single phase output with 1 hour battery back up complete with all accessories as required. (Including base frames , earthing, termination with FP Isolator/MCB fixing wit sheet stee; enclosure on surface - incoming & outgoing side etc)
Appendix K - Electrical Substation
OD31439/2023-2024:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 240 sqmm XLPE Al
OD10875/2024-2025:OD: od325362/2021_2022 : Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required 1000 MM WIDTH X 50 MM DEPTH X 2 MM THICKNESS
OD10876/2024-2025:OD: Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required 100 MM WIDTH X 50 MM DEPTH X 2 MM THICKNESS
OD10877/2024-2025:OD: Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required 600 MM WIDTH X 50 MM DEPTH X 2 MM THICKNESS
OD10878/2024-2025:OD: Fabrication, supply and installation of following size of Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M8 threaded rod and all necessery accessories as required 300 MM WIDTH X 50 MM DEPTH X 2 MM THICKNESS
OD10726/2024-2025:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 95 sqmm XLPE Al
OD10727/2024-2025:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required 3.5C 185 sqmm XLPE Al
OD10730/2024-2025:Supply of one number PVC insulated and PVC sheathed / XLPE armoured Copper power cable of 1.1 KV grade of following sizes as required 4C 6 sqmm XLPE Cu
OD10731/2024-2025:Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required.4C 6 sqmm XLPE Cu"
9.1.24:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)
9.1.27:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)
9.1.29:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)
OD31606/2023-2024:Supplying and providing of maintenance free earthing system comprises of molecularly bonded copper of 99.9% purity on low carbon steel of min 3048mm length (10 feet), having a diameter of 20mm with copper bonding thickness of 250 microns. The Rod has to be either continuous or with self-coupling peg & bore arrangement with fault current withstand capability of 30 kA rms value for 1 second and I peak of 76 kA. The rod must be having corrosion test, peel off test for uniform coating, 180 degree bend test with out peel off of copper bonding. Exothermic welded clamp for clamping as suggested as per NBC 2016. Ordinary stainless steel/Copper alloy universal clamps are not recommended. For self coupling peg & bore arrangement rod needs Impact point on the bottom rod for easy insertion. Earth enhancing mineral compound is used for improving the soil conductivity. The material shall be mineral inert to sub soil and shall not pollute the environment and non corrosive to earth rod. The material should have a resistivity less than 0.2 Ωm. It should be free from hazardous substances. The mineral compound is required to have minimum 17.5 Kg of the total composite. The compound should be chemically inert. Concrete earth electrode inspection chamber with weight bearing capacity of 30kN. The dimension shall be 320mmX 320mmX 190mm. Make: Cape or equivalent
OD31607/2023-2024:Supply and fixing following size earth bench, fixing on surface of wall/parapet using iron screws, bench having holes for connecting earth strip/wires, making good the damages, colour washing etc as required. 25x3x400 mm Cu earth bench.
OD10728/2024-2025:Supply and fixing of 450 x 450 mm SFRC Heavy duty manhole cover with frame having clear opening 450 x450 mm and outer frame size 770x770x165mm and cover size 590x590x90mm, the weight of the cover to be not less than 185kg.
OD10729/2024-2025:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required (for horizontal run)25 x 3 mm copper strip
OD31598/2023-2024:MAIN PANEL/METERING PANEL OF CA2 Item code - OD Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent) Incomer: RYB indicator with control fuses - 1 set, Multi function meter - 1 nos, 400/5A CL 1 5VA CT - 1 set, busbar mounted surge protection device (Type-1) -1no, 400A 36kA FP micro processor based MCCB - 1 no, Busbar: copper busbar suitable for 400AOutgoings: 160A 25kA TPN MCCB - 1 no, 125A 25kA TPN MCCB - 1 no, 100A 25kA TPN MCCB - 1 no, 160/5A CL 0.5S 15VA CT - 2 set, 160A Fuse base & fuse link -6nos, 160A Neutral Link-1no, 125A Neutral Link-1no, Provision for fixing three phase CT energy meter - 2nos , Dummy provision shall be given as per schematic diagram and all neccessories accessories as required.
OD31596/2023-2024:OD : SUB MAIN LT PANEL Item code - OD Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent) -Incomer: RYB indicator with control fuses - 1 set, Multi function meter - 1 nos, 400/5A CL 1 5VA CT - 1 set, busbar mounted surge protection device (Type?1) -1no, 400A 25kA FP TM MCCB - 1 no, Busbar: copper busbar suitable for 400A, Outgoings: 160A 16kA TPN MCCB - 2 nos, 100A 16kA TPN MCCB - 2 nos,63A 16kA TPN MCCB - 4 nos,40A 16kA TPN MCCB - 1 nos and all neccessories accessories as required.
OD31597/2023-2024:KISOK MAIN PANEL Item code - OD Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent) Incomer: RYB indicator with control fuses - 1 set, Multi function meter - 1 nos, 400/5A CL 1 5VA CT - 1 set, busbar mounted surge protection device (Type?1) -1no, 315A 25kA FP TM MCCB - 1 no, Busbar: copper busbar suitable for 315AOutgoings: 125A 16kA TPN MCCB - 1 nos ,63A 16kA TPN MCCB - 7 nos and all neccessories accessories as required
OD31599/2023-2024:OD : Supply and fixing framed shock treatment chart as required
OD31600/2023-2024: OD :Supply of first aid box as required
OD31601/2023-2024:OD : Supplying of Rubber hand gloves suitable for 11 KV
OD31602/2023-2024:OD : Supply and fixing 9 litre capacity fire bucket as required
OD31603/2023-2024:OD : Supply and fixing of 6kg capacity ABC type dry chemical powder fire extinguisher as required
OD31604/2023-2024:OD : Installation, testing and commissioning of 400kVA, 11KV/433V, 3 phase, Vector DYN-11 dry type Indoor transformer as required.
OD31605/2023-2024: OD : Supply of 400kVA, 11KV/433V, 3 phase, outdoor type, vector DYN-11 Cast Resin transformer with CRGO Core, off load tappings from +5% to -10% in steps of 2.5%, changeable on offcircuit by tap links provided, with WTI & LV terminals suitable 2 runs of PVCA cable and HV terminals connected to 11KV, 26.3 KA, 630A VCB Panel, with incoming suitable for XLPE cable and output connected to 11KV seal off bushings to the transformer. with all other standard fittings and accessories confirming to IS:11171/1985, 2026/2011 etc as required. offcircuit by tap links provided, with WTI & LV terminals suitable 2 runs of PVCA cable and HV terminals connected to 11KV, 26.3 KA, 630A VCB Panel, with incoming suitable for XLPE cable and output connected to 11KV seal off bushings to the transformer. with all other standard fittings and accessories confirming to IS:11171/1985, 2026/2011 etc as required
OD10892/2024-2025:60 KVAR APFC PANEL -kiosk side OD : Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent) Outgoing switchgear etc. (all feeder unit Would be compartmentalized), color coded PVC sleeved vertical / horizontal Aluminium busbar of required size of length, (bus-bar distances shall be minimum 32 mm ) insulators, hardware, neoprene gasket , hinged door, interconnecting single core multi strand lugged copper wire having current density of 2A / sqmm of suitable capacity &amp; size with lugs from busbar to switchgears / MCCB / MCB or where ever required, control wiring with 1.5 sqmm FRLS cable, ON/OFF, RYB phase indicators, two earthing terminal busbar of size 25 x 5 mm copper with nut &amp; bolts at outside of the panel, rating and name plates for all incoming &amp; outgoings etc. comprising with the followings as per the KEI standard. Switch gears &ndash; ABB/ Equivalent, Contactors &ndash; ABB, L&amp;T/Equivalent. Incomer: - 160A, 4P 23KA MCCB. Outgoing: 63A 10kA 3P MCB - 2 no, 50A 10kA 3P MCB - 1 nos, 32A 10kA 3P MCB - 1 nos ,16A 10kA 3P MCB - 2 nos. Capacitors: 20KVAr - 1 no, 15KVAr - 1no, 10KVAr - 2 no &amp;5 KVAr - 1 no capacitors in steps with capacitor duty contactors.
OD10893/2024-2025:70KVAR APFC PANEL - Main LT side OD : Supply, installation, testing and commissioning of outdoor floor mounting feeder pillar panel made of Glass Reinforced Plastic (GRP)/Polycarbonate. The Degree of Ingress Protection IP 65,/66 impact protection shall be IK08/10.The panel shall be comprising of the following and shall be fully wired as per latest electrical standards with hot dipped MS canopy, MS mounting frame and all necessary accessories, ready to use (Make: Cape or equivalent) Outgoing switchgear etc. (all feeder unit Would be compartmentalized), color coded PVC sleeved vertical / horizontal Aluminium busbar of required size of length, (bus-bar distances shall be minimum 32 mm ) insulators, hardware, neoprene gasket , hinged door, interconnecting single core multi strand lugged copper wire having current density of 2A / sqmm of suitable capacity &amp; size with lugs from busbar to switchgears / MCCB / MCB or where ever required, control wiring with 1.5 sqmm FRLS cable, ON/OFF, RYB phase indicators, two earthing terminal busbar of size 25 x 5 mm copper with nut &amp; bolts at outside of the panel, rating and name plates for all incoming &amp; outgoings etc. comprising with the followings as per the KEI standard. Switch gears &ndash; ABB/ Equivalent, Contactors &ndash; ABB, L&amp;T/Equivalent. Incomer: - 160A, 4P 23KA MCCB. Outgoing: 63A 10kA 3P MCB - 2 no, 50A 10kA 3P MCB - 1 nos, 32A 10kA 3P MCB - 1 nos ,16A 10kA 3P MCB - 2 nos. Capacitors: 20KVAr - 2 no, 15KVAr - 1no, 10KVAr - 1 no &amp;5 KVAr - 1 no capacitors in steps with capacitor duty contactors.
Appendix L - Solar PV System
OD31560/2023-2024:Supply, Installation, Testing and Commissioning of 10 kW Off-grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Solar PV panel, necessary protections, earthing, lightning protection and PV panels mounted on Aluminium structure of suitable strength with following components complete as required:- 1)Solar Photovoltaic Module Mono Per half cut of capacity 545Wp Wp or above, manufactured in India, conforming to IS14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photo Voltaic Module conversion efficiency shall not be less than 18.3%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. 2) Two units of Solar Off-grid MPPT pure sine wave Inverter 5KVA/48V with parallel PCBA ports for parallel connection of Inverters, USB port and RS232 port with RJ45 connector and with Communication Modbus protocol with LAN/WAN/GSM/Wi-fi options along with remote access facility and SNMP monitoring device and latest remote monitoring software, with surge protections and battery overcharge protection for Lithium-Ion battery and LCD display with measurable parameters dispalyed on it and IP-21 rating for enclosure. 3) Two units of High capacity Lithium Ion batteries for the Inverter, 100AH/48V 5KWh with 5 year warranty, with charge efficiency more than 90%, also features current limiter and other protection features, with RS232 communication ports and LED interface, it should be extendable with parallel connecting modules upto 8(with CBMS), Long cycle life : 3000 cycles @ 80% DoD at STC, wide working temperature and cabinet/rack/wall mountable. 4) Lightning and surge voltage protection. Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control and solar DC cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing necessary channel/conduit lugs and other accessories etc. as required including all equipment required for the same such as breakers, isolators, lightning arrestors, panels, protection equipment, cables, conductors and SPV Panel yard etc. as per statutory requirements and comply with the CERC Grid code. Each of the equipment/ components utilised shall be compliant and be subjected to all routine and acceptance tests prescribed in the relevant Indian Standard Specification/IEC. 5)Comprehensive AMC of the entire solar power plant for 5 years from the date of handing over. The cost includes all spares, cleaning charges, data and recurring charges for communication equipment, etc. as required.
OD31570/2023-2024:Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/PolyCrystalline silicon solar cells, netmetering facility, necessary protections, earthing, mounted on Aluminium/GIstructure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to IS14286/IEC61215,IS/IEC61730-Part-1,IS/IEC61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b)Power Conditioning Unit (PCU)of 350-800V DC Input voltage range and 400VAC, three phase, 4 wire, 50Hz+/-2.5Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d)Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f)Connections &I nterconnections by supplying & fixing required size XLPE insulated copper conductor 1.1kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.
Appendix M - Miscellaneous works ( Foundation for light poles, signage , cycle track, planter box )
2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil
2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil
2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
OD13677/2023-2024: Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete."
16.78.1:Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30
13.65.1:Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work
4.20.1.2:Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note : 1) Excess /less cement used than specified in this item is payble / recoverable separately.M-15 grade plain cement concrete (cement content considered @ 220 kg/cum)
20.2A.1:Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.600 mm dia piles
OD27931/2023-2024:Providing and laying in position machine batched and machine mixed design mix M40 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge . All works above plinth level upto floor V level
OD14021/2023-2024:Supplying and placing high corrossion resistant steel (HCR) for RCC work including straightening g<br>,cutting,bending ,placing in position and binding all complete .HCR bars of grade Fe<br>500d or more- "
5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
22.22A:Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.
10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)
Appendix N - Floating Jetty
OD11893/2024-2025:Providing installing monolithic float module cast monolithically in single pour and covered in concrete in all six sides closed cells expanded polystyrene is encased inside the concrete shell giving maximum strength and low water absorbtion ,with proven water and thru-rods connection method optimum for marine environment ,state of the art FRP thru rods ,cast in race ways to provide maximum protection and preserve a clean appearance including all cost of design supply installation labour materials etc complete as directed by engineer in charge .
Appendix O - Civil work STP and WTP and Electrical works
2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil
2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil
2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
OD28133/2023-2024: Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete."
4.20.1.2:Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS:9103 to accelerate/retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. Note : 1) Excess /less cement used than specified in this item is payble / recoverable separately.M-15 grade plain cement concrete (cement content considered @ 220 kg/cum)
5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level
OD28137/2023-2024:Supplying and placing high corrossion resistant steel (HCR) for RCC work including straightening g<br>,cutting,bending ,placing in position and binding all complete .HCR bars of grade Fe<br>500d or more- "
5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
APPENDIX P - ELV
OD10751/2024-2025:OD :Supply and laying of Outdoor Cat 6 UTP Cable through exisiting conduits
1.53.1:Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable
1.21.1:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm
1.21.2:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm
OD10756/2024-2025:Supply and installation of Cat 6 RJ 45 Connectors with boot.
OD10758/2024-2025:Supply and installation of 1 Meter Cat 6 UTP Patch Cord
OD10759/2024-2025:Supply and installation of Cat6 UTP , Patch Panel - 24 ports fully loaded patch panel with rear strain release bar.
OD10761/2024-2025:Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including 3x3 or suitable size moulded plastic Camera Co box on surface
OD10793/2024-2025:Supply & Fixing of 4x4 or suitable weatherproof moulded plastic co box on surface with cover plate for CCTV ,IP Rated.
OD10794/2024-2025:Supply, installation, testing and commissioning of GI pole of 3.5m height, 3 inch
OD10815/2024-2025:Supply and installation of 19" 21U Floor Mount Network Rack with Glass Door,2 No of candiliver shelf, 4 No of Rack Mountable Fan, 2 No of Rack mountable Vertical PDU with Minimum 6 Sockets 5/15A indian round pin , Lock & Key and Mounting Accessories.
OD10814/2024-2025:Supply installation testing and commissioning of 4.5 Metre height decorative pole made of mild steel/steel tube have minimum thickness of 2.5- 3mm. The pole shall have two section, base section having length of 1metre with dia of 140mm and top section having length of 3.5 metre with dia of 76mm . The pole shall be with a overhang of 1m. Pole shall be mounted on square base plate of dimensions 250x250x12mm thickness. The base section of Pole shall have an in-built junction box with anti?theft lock arrangement. The Pole shaft should be fabricated out of Steel tube of grade YST 240. Structurally designed base plate of Steel A36/A572-50 or equivalent should be welded with the pole shaft. The pole shall be designed as per EN40 for withstand basic wind speed of 169kmph. The complete structure should be hot dip galvanised and marine grade treated. Base plate fixing in existing foundation with bolt and all accessories as required.(Excluding civil foundation). Make: KESSLEC HDGI NEMO or equivalent
OD10845/2024-2025:Supplying and laying of following size DWC HDPE pipe lSI marked along with all accessories like socket, bend, couplers etc. 40 mm Size
OD10847/2024-2025:Supply and installation of Weatherproof Junction Box with Minimum Dimensions W 275 x H 575 x D 195 mm Including 4Nos 20mm Grommets, 4Nos 20mm Cable glands, Pole Mount Bracket and Accessories
OD10850/2024-2025:Supply and installation of Base-Lx to 1000 Base-T PoE Media Converter
OD10853/2024-2025:Supply and installation of 8 Port Manageable PoE Switch with min 2 x 1G Uplink Port.
OD10855/2024-2025:Supply and installation of 16 Port 1G SFP Fiber Switch with min 2 x 1G Uplink Port
OD10856/2024-2025:Supply and installation of 1G SFP Module
OD10857/2024-2025:Supply, Installation Testing and Commission of 2MP PTZ Camera IR Outdoor PTZ Camera : 1/1.8" Progressive Scan CMOS Up to 1920 × 1080 resolution Min. Illumination: Colour: 0.002 Lux @(F1.5, AGC ON), B/W: 0.0002 Lux@(F1.5, AGC ON) with IR CCTV shall have inbuild SD card slot 32 × optical zoom, 16 × digital zoom Range : up to 200m, 360° PAN ,-15° to 90° (auto flip): Tilt 140 dB WDR, 3D DNR, HLC Support H.265+/H.265 video compression Support Rapid focus IK10, IP67. with all required accessories for mounting. Make: AXIS Q6315-LE/ Bosch/ Pelco
OD10858/2024-2025:Supply, Installation Testing and Commission of 4MP IP Dome Camera, 2.8mm or optional fixed lens , H.265 /H.264 encoding, Day/Night(ICR), DWDR, IR LEDs Length 30m or higher Ip66, PoE. Three year warranty and onsite support.Make: AXIS M3116-LVE/ Bosch/Pelco
OD10859/2024-2025:Supply, Installation Testing and Commission of 2MP IP Outdoor Bullet Camera, 3.6mm or optional fixed lens , H.265 /H.264 encoding, Day/Night (ICR), 120WDR, IR LEDs Length 30m, On vif, IP66 or Higher, PoE. Make: AXIS P1465-LE/ Bosch/ Pelco
OD10860/2024-2025:Supply, Installation Testing and Commission of 32 Channel NVR support upto 8MP at 320mbps or higher , Supports 4K, 4 HDD SATA supports , HDMI,VGA support, H264/H.265 Compression, RAID 5 Support, Onvif profile.Three year warranty. Make Axis s1232/Bosch/Pelco
OD10861/2024-2025:Supply and installation of 6 TB Surveillance hard disk
OD10862/2024-2025:Supply and installation of Wireless Keyboard & Mouse
OD10863/2024-2025:Supply and installation of 43" HD LED 24 x 7 monitor
OD10864/2024-2025:Supply and installation of 10 mtrs HDMI cable
OD10881/2024-2025:Supply and installation of 12 core Single Mode OS2 armoured fibre cable
OD10885/2024-2025:Supply and installation of Single Mode fibre cable Spicing Box.
OD10886/2024-2025:Supply and installation of 24 port rack mountable LIU fully loaded with LC duplex adaptor, couplers, 1.5mtr SM OS2 LC pigtails, blank plates with rack mounting accessories
OD10888/2024-2025:Supply and installation of Fiber Optic Patch Cord LC-LC, Duplex, Single Mode, 3 meter
OD10890/2024-2025:Providing Splicing Charges
90.12.9.2:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench50/38 mm or nearest size
14.14.2:Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.150 mm dia
APEENDIX- Q -STP AND WTP
OD10774/2024-2025:Erection and commissioning charge for completing the works
OD10775/2024-2025:Supplying and installation of Interconnection piping works using UPVC pipe, UPVC pipe, NRV , PVC ball valves etc. and necessary other fittings etc., complete.
OD10776/2024-2025:Supply and Installation charges for Electrical work including Control panel, DOL Motor Starter Panel For Raw Water Pump near the plant, Electrical Cable from Raw Water Pump to Starter,On /off switch,mcb etc
OD10777/2024-2025:Supply of Hypochlorite Dosing System Pump of capacity 0-6 LPH at 4 KG,100 ltrs, LDPE with necessary unions, flanges etc., complete.
OD10778/2024-2025:Supply of back wash pump having capacity 15cum/ hr, 10 MLC head of Monoblock type made of cast iron (1W+1S)
OD10779/2024-2025:Supply of Filter feed pump having capacity 6.5cum/ hr, 35 MLC head of Monoblock type made of cast iron (1W+1S)
OD10780/2024-2025:Supply of Activated Carbon Filter 6500Ltrs/hr capacity with FRP vessel having size 0.76 m dia x 1.8 m height with necessary frontal piping, valves, suitable support for mounting, pressure gauge with filtering media of Activated Carbon,Graded Pebble.
OD10781/2024-2025:Supply of Pressure Sand Filter of 6500 Ltrs/hr capacity with FRP vessel having size 0.76 m dia x 1.82 m height with necessary frontal piping, valves, suitable support for mounting, pressure gauge with filtering media of Graded pebble, coarse Silex and Fine Sand.
OD10795/2024-2025:Supplying and installation of FRP Tank
OD10796/2024-2025:Ultra Filteration Supplying and Fixing of 3cum/hr Ultra Filteration Plant
OD10797/2024-2025:Erection and Commissioning
OD10798/2024-2025:Chemical Dosing Supplying and Fixing of Chemical Dosing Pump with capacity 0- 4LPH including 50ltrs Dosing Tank
OD10799/2024-2025:Hypo Dosing Supplying and Fixing of Hypo Dosing Pump with capacity 0- 4LPH including 50ltrs Dosing Tank
OD10800/2024-2025:Supplying and Fixing of Electrical Panel consisting of PLC(Delta /equivalent)phase indicator, LP/HP indicator, Pump ON-OFF, MainSwitch, Contactor with Overload relay, Fuse fittings, Interconnecting wires,TOD meter. etc
OD10801/2024-2025:Supply and fixing of Electrical Accessories and instrumentation
OD10802/2024-2025:Supply and fixing of Inter connecting pipes and fittings using UPVC/CPVC Pipes and Fittings
OD10803/2024-2025:Anaerobic Media Supply and fixing of Anaerobic media of Required Size
OD10804/2024-2025:Supply & Fixing of Vertical Type Activated Carbon Filter of FRP make vessel having a flow rate of 3m3/hr and size of 600mm dia x 1820mm ht operating at 5 kg/cm2 including necessary frontal piping(UPVC/PVC), valves, suitable support for mounting, pressure gauge with filtering media of Silex, Graded Pebbles, Gravels/ACF
OD10805/2024-2025:Supply & Fixing of Vertical Type Pressure Sand Filter of FRP make vessel having a flow rate of 3m3/hr and size of 600mm dia x 1800mm ht operating at 5 kg/cm2 including necessary frontal piping(UPVC/PVC), valves, suitable support for mounting, pressure gauge with filtering media of Silex, Graded Pebbles, Gravels media
OD10806/2024-2025:Supply & Fixing of Filter Feed Pump( Horizontal Centrifugal) of CI construction capable of giving 3.25m3/Hr at 30m head & working on 3PH,50 Hz, with necessary accessories such as Base Plate, Coupling, Valves,etc complete. Pump should be 1 no. 1working + 1 no. standby= 1SET
OD10807/2024-2025:Supply & Fixing of 0.5 KW Anoxic Recirculation Pump of CI construction capable of giving 9m3/Hr at 10-12m head with self priming type , with necessary accessories such as Base Plate, Coupling, Valves,etc complete.
OD10808/2024-2025:MBBR Media. Supply & Fixing of Cylindrical type White colour MBBR media of size 22mm dia x 16mm thick having an effective surface area of 400m2/m3.
OD10809/2024-2025:Supply & Fixing of Disc Type Diffuser with Air Flow made of EPDM with 3/4” NPT male connection,PVC Support and necessary valves and fittings This includes jointing of pipes & fittings with one step solvent cement.
OD10810/2024-2025:Supply & Fixing of Twin Lobe Rotary Air Blower having 80m3/hr capacity and 0.3kg/cm2 pressure with ,1400rpm and working on 3PH,50 Hz, with accessories such as Base frames, Air filter for Suction line and silencer for discharge line, Safety guard for belt drive , vibration elimination pads. (1 working + 1 stand by)
OD10811/2024-2025:Supply & Fixing of 1 HP / 0.75 KW Waste water transfer Pump(Submersible type) of CI construction capable of giving 3.25 m3/Hr at 10m head & working on 3PH,50 Hz, with necessary accessories such as Base Plate, Coupling, Valves,etc complete.Pump should be 1 no. 1working + 1 no. standby= 1SET
OD10812/2024-2025:Bar Screen Supply & Fixing of Bar screen Made of SS 304 suitable for placing inside the screen chamber, With Designed Flow of 3.25m3/day and spacing of 10mm ,with Angle Of Inclination 45 deg for collecting Debris such as Plastic bag, Paper Cups, Sanitary Napkins, Dishes Etc Comple
APPENDIX R-IRRIGATION
50.18.9.7.1:Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm2
50.18.9.8.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2
OD10923/2024-2025:Providing and fixing PVC pipes includes joints of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work -BuriedOd Derived 50.18.9.8.1 90 mm dia 6.Kgf/cm2
50.18.9.9.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2
50.18.9.20.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend
50.18.9.20.9:Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling
50.18.9.20.8:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia End cap
50.18.9.21.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend
50.18.9.21.9:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling
50.18.9.21.10:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x63 mm dia Reducer
50.18.9.22.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend
50.18.9.22.11:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling
50.18.9.22.12:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer
OD10902/2024-2025:Supply, Fixing & Commissioning of 2" Valve Max. Flow - 20 M3/H @0.2m Head Loss,15nos DC Latch Coil for Field Valve with Quick Pressure Relief Safety Valve for Mainlineetc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10906/2024-2025:Supply,Fixing & commissioning of Supply,Fixing & commissioning of Pressure release valve 2" with pressure setting from 0 to 7 Bar etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge
OD10907/2024-2025:Supply,Fixing & commissioning of a double acting air and vaccum release 1/2 " Air release valve . The Air release valve shall be capable of both releasing and admitting air from and into the line. The working pressure shall be 5 bar. Only for Drip Irrigation etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10908/2024-2025:Supply,Fixing & commissioning of pressure gauge of 250mm Dial with maximum working pressure for 8bar,1/4"BSP etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10909/2024-2025:Supply,Fixing & commissioning of 4'' control Valve, Butterfly Valve flange & Tail Piece in mainline for bypass and flow diversion of approved quality with pressure rating of PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10910/2024-2025:Supply,Fixing & commissioning of 4'' Non Return Valve to prevent back flow have flap type or spring type with pressure rating of PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10911/2024-2025:Supply,Fixing & commissioning of 63mm dia valves that are installed at the end of the irrigation line for effecting flushing of the line at the beginning of every irrigation cycle, thus avoiding the clogging of the emitters /sprinklers through removal of particles, sediments and other impurities from the water. etc., complete, as per the instructions of Architect/Landscape
OD10913/2024-2025:Supply,Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Unique Barb Design to Reduce Insertion Force. Non - Obtrusive Brown Colored Fittings of 17mm Tee . etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10914/2024-2025:Supply,Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Unique Barb Design to Reduce Insertion Force. Non - Colored Fittings of 17mm Reducer ELBOW. etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge
OD10915/2024-2025:Supply,Fixing & commissioning of 17mm End cap S Type for dripline closure at the end of the dripline etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10916/2024-2025:Supply,Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Unique Barb Design to Reduce Insertion Force. Non - Obtrusive Brown Colored Fittings of Take Off Nipple . etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge
OD10917/2024-2025:Supply,Fixing & commissioning of Gromatetake off Connects Drip Line and Blank Tubing to PVC Mainlines at Low Pressures. 17mm GTO etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10918/2024-2025:Supply, Fixing & Commissioning of flexible 16mm inline tubing, Pressure compensating Dripper 40cm spacing and 2L/H discharge, etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10919/2024-2025:Supply, Fixing & Commissioning of flexible 16mm inline tubing Pressure compensated Drip line 0.6L/H Discharge @ 20cm Spacing , Dripper Spacing at 20 Spacing wall thickness 1.2mm etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge
OD10920/2024-2025:Supply, Fixing & Commissioning of flexible 16mm inline tubing with resistance to UV damage, algae growth brown in colour, Longer lateral run lengh with flow rate 2.3lph to 3.4 lph, pressure rating 2.5 bar , Dripper Spacing at 30 cm , 40 cm & 60 cm Spacing wall thickness 1.2mm etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.
OD10921/2024-2025:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 90 mm dia Socket /coupling
OD10922/2024-2025:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 90 mm dia Bend
50.18.9.6.2:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 6 Kgf/cm2
OD10993/2024-2025:Supply ,fixing and commissioning of RTU unit with cable,solar pannel and antenna for solenoid valve with all complete as per direction of the engineer in charge
OD10994/2024-2025:Providing, fixing, and commissioning of Valve box for solenoid valve, UV protectant made by rain bird or equivalent including labour charges as per direction of engineer in charge
PAULOSE GEORGE CONSTRUCTION COMPANY PVT LTD (BID ID -1922523)
Bidder Name
THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY
PAULOSE GEORGE CONSTRUCTION COMPANY PVT LTD
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.05 MB
Download all tender documents and submit your bid