SPECIAL REPAIR TO BLDG NO P34 SUGAR STORAGE SHED OF 311 COY ASC SUP TYPE B UNDER GE MISAMARI

Amount

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Taking down cement or cement lime plaster of any description incl dado/ skirting of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water, remover debris etc complete all as specified and as directed by the Engineer-in-Charge

M & L 40 mm thick & PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floors, finishing cement concrete surface even and smooth w/o using extra cement complete all as specified and directed.

S&F for glass dividing strips, 3 mm thick and and 38mm wide inserted in position, complete all as specified and directed.

M & L for PCC 1:2:4 type B-1, 100mm thick using 20mm graded aggregate as in floors in alternate bays, complete all as specified and directed.

M & L for rendering in cement mortar (1:6), 15 mm thick on brick wall or on concrete surfaces finished fair & even complete all as specified and directed

M&L for preparation of newly plastered surface of walls and apply two coats of oil bound distemper over and including a coat of 1mm average thick wall putty, complete all as specified & directed.

M&L for complete removal of existing treatment of old plastered surface of walls and apply two coats of oil bound distemper over and including a coat of 1mm average thick wall putty, complete all as specified & directed.

M & L for rendering in cement mortar (1: 4), 15mm thick on concrete/ brick masonry wall surfaces, finished fair and even, complete all as specified and directed.

M&L Rendering 15mm thick on Brick Work or Concrete Surfaces (in drain, etc.) in Cement Mortar 1:4, mixing with WPC as per Manufacturer’s Instructions, finishing Plastered Surfaces Even and Smooth without using extra Cement, complete all as specified and as directed. NOTE:- Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item as 'Supply only'.

Supply only Integral Water Proofing Compound, conforming to IS 2465-1975 complete all as specified.

M&L for preparation of newly plastered surface of walls of wall and applying two Exterior Acrylic Emulsion paint over a coat of alkali resistant primer, complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered surface of wall and applying two Exterior Acrylic Emulsion paint over a coat of alkali resistant primer, complete all as specified and directed.

M&L Cement Concrete 1:2:4 (20mm graded aggregate) in Channels, etc. in Manhole including necessary Formwork (if required), complete all as specified and as directed.

M&L Extra forming Fair Finished to Drains or Channels 30 Cm Inner Girth in Cement Concrete using Extra Cement including Forms Moulds Mitred/ Stopped Ends, etc., complete all as specified and as directed.

M & L for 75mm thick Cement concrete 1:3:6, type C-2 using 40mm graded aggregate as in floor finishes / plinth protection laid in alternate bays not exceeding 2 mtr in length each bay including cutting groove of 6mm wide and 10mm deep filled with bituminious mastic , finished fair and even complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed by the Engineer-in-Charge

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed

S&F sheet glass, ordinary quality 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane complete all as specified and directed.

Hacking out old, broken glass (any thickness, size quality or description) from wooden/steel frames, glazed with oil putty or fixed with beads .

S&F in repair framed work as in doors or gates of approved pattern & design of angle or other section conforming Fe 290 (Gde-E- 165) with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering of doors, etc. to be prepared for hanging or sliding with and including either hooking and hinges or steel hanging door fittings (including of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, complete all as specefied and and directed.

S&F in repair rolled section as in main and cross beams, hip and jack rafters, purline where connected to common rafters and rainning rails and guides for sliding doors fixed with angle cleats or other connecting plates of grade Fe-410W (gde-E-250) quality-A, complete all as specified and directed.

M&L for Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes ,Fe 410-W (Gde-E- 250) quality- A, complete all as specified and directed.

M&L 1.25mm Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified.

M&L for prepration of new or untreated steel surfaces and applying two coats of synthetic enamel paint over a cot of red oxide zinc chrome primer, complete all as specfied and directed.

M & L for preparation of old painted steel surfaces of any description over 10cm width or girth & applying two coat of synthetic enamel paint of approved quality, tint to achieve glossy finish, complete all as specified and directed.

M&L cement concrete type D-2, 1:4:8(40 mm graded aggregate), 100 mm thick as in sub base, complete all as specified and directed.

M & L for PCC inter locking paver block 50 to 60 mm thick ,coloured, reflective type, of approved quality, M-35 Grade with grey cement and pigment laid over and incl 25 mm thick sand cushion vibrated with mechanical vibrator, complete all as specified and directed.

Demolition Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any description, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in coping etc including necessary form work, weathering slightly rounded or chamfered angles and throating complete all as spfd and directed.

Dismantling AC/galvalume/fiber glass sheet (corrugated or semi corrugated) in roof coverings complete all as specified and directed

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S & F Pre- painted galvatume aluminum zinc coating GI based plain ridge sheet of suitable profile for roof sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof including taking down old, complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

M&L for 1.25mm thick Mild steel sheet eaves gutters, galvanised class 3, half round exc. 150mm dia with rounded edges, complete all as specified and directed.

S&F in repair PVC (SWR) pipe 110mm bore (dia), single socketed with Rubber Ring Joints, in any length and fixing to Walls, clamp/hook for holding of pipe etc. including taking down unserviceable Pipe, complete all as specified and as directed.

S&F in repair PVC (SWR) 110mm bore (dia) Bend any type, provided with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

Demolition of re-inforcment cement concrete of any description and in any position not otherwise specifically provided, complete all as specified and directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M & L for mild steel TMT bars of 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge

M&L RCC (1:2:4) type B1 as in columns and similar works, complete all as specified and directed. NOTE : Reinforcement will be Measured and Paid separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Cover Slab of Manholes, Septic Tanks, etc., set in Cement Mortar 1:4 including necessary forms, moulds, etc., complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid separately under appropriate Items.

M&L for formwork to sides of concrete columns (Square, rectangular or polygonal etc) for rough finished surfaces of concrete, complete all as specified and directed.

Dismantling wall and ceilling boards of any description including cover fillets complete.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in framed works.

S&F 2nd class HW plain fillets square rectangular triangular in section, clean sawn secured with nails sectional area exc. 13 sqcm but n.exc 25 sqcm

All as per item No 48 above but sectional area exc 3 sqm & n.exc 6 sqcm.

M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with nails as in ceiling, complete all as specified and directed.

S&F for Turbo Ventilators Industrial/ domestic turbo ventilator as in Manufactureres Instruction:- (i)(Turbine Dia 28 Inch (760mm)),(Neck/Throat:-24"),(Height:-18"/610mm) (Vanes(Blades):- 42 Vanes, Aluminium 0.50 mm Alloy 8011), ( Base Ring MOC (Mounting ring:- Stainless steel),( Top Plate MOC :- Stainless Steel 0.80 mm thickness ) (ii) Rotation:- Twin Sealed 6203ZZ bearing with self lubricating Duponty Zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity Twin Sealed 6201ZZ bearings with self lubricating Duponty Zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity (iii) ( Centre shaft : 18mm high carbon steel zinc plated, ) ( Inner Arms :- M.S. with electro zic plating), ( Outer Arms:- M.S. with electro znc plating ), ( Frp base plate:- 2mm thick clear 1.020 mtr wide 1.65 mtr long matching your sheet profile Weight 8 kg -Approx), (Centre Width:- 800mm+/-5mm ), ( Dia of Bottom Ring :- 600mm +/- 15mm ), ( Nos of Bearings:-02 Nos ), (Bearing Type :- skf-6001ZZ & 6003ZZ ) (Rivets :- Aluminium Alloy with Washer) Make:- Turbo Ventilatior India (INDUSTRIAL VENTILATING SOLUTIONS)/ Equilent

Taking down carefully existing unserviceable copper/ aluminium point wiring (light,call bell, two way, socket or power point etc) complete with fittings/fixures such as switches sockets, ceiling rose, fan regulators,bracket light fittings and making good to the disturbed surface complete all as directed by Engr-in-Charge.

Taking down the existing unservicable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down existing unserviceable Landscape light/Street Light/ Building Security light of any description/type/ size ,carefully from Pool/Pole/Building, including removal of batten/ conduit/ gutties/ Poly Carbonate boards complete all as specified and directed by Engr-in-charge.

Taking down carefully unsv aluminium submain wiring of any type /loc including conduit /casing and earth wire and making distributed surface of walls /ceiling matching with existing colour.

Taking out unsv UG Cable any cross sectional area and connection of any description of any description laying in trenches or fixing with wall or poles all as specified and directed.

M & L for Point wiring with 1.5 Sq mm copper conductor single core FRLSH PVC insulated unsheathed 1100 Volts multistranded drawn through and including rigid PVC Concealed Conduit pipe and its accessories of suitable size, high grade ISI marked in walls /roof and PVC boxes of suitable size including fixing/grouting PVC Board as per site requirement for mounting the switches / sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLSH PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for One light point controlled by one, one way switch 5 Amps

One ceiling fan / exhaust fan point controlled by one , one way switch and regulator

One 3 point 5 Amps socket outlets point controlled by one switch on the same board

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

All as per item No 1 above but with 2.5 sqmm multi stranded copper conductor 1100 volts grade FR-LSH PVC insulated sheathed cable with FR-LSH PVC 2.5 Sqmm multi standard insulated unsheathed copper wire for continues earth on independent board.

S & F Switch piano flush type single pole one way 5 Amp, 230 Volts complete all as specified.

S & F Socket outlet 2 in 1, 3 pin, 5 Amps complete all as specified and directed.

S & F Switch socket combination flush type multipurpose 2/3 pin 5 Amps two in one , 230 volts complete all as specified

S&F Switch socket combination 2 in 1 3 pin, 15 Amp flush type universal.

S&F ceilling rose three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm complete all specified

S & F ceiling fan regulator step type, flush type heavy duty suitable to work on 230 Volt AC supply complete all as specified.

S & F Lamp holder with insulated body, with back plate suitable for batten fittings complete all as directed.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified.Make-Make- Havells, Cat No: LHLDEUEBML8Z010 or equivalent in CG or Polycab.

S & F sheet metal enclosure MCB VTPN 8 way Double door Ready to use DBs - Provided with insulated vertical phase bus-bars |neutral bar/s with shroud/s | earth bar/s | sticking saddles | cement spill protector | color-coded interconnecting wire set | cable ties | blanking plates and circuit identification labels With provision for 4 Pole MCCB 200 A as incomer and SP/SPN MCBs as outgoing complete all as specified and directed.Make- L&T, Cat No: DBVTH008DD and equivalent in Legrand and Indo Asian.

S & F MCCB 4 Pole 200 Amps, thermal magnetic type DN2-250D with breaking capacity 36 KA with thermal magnetic release at 415 volts, including spreader terminal, make: L&T Cat part No. CM92108OOL1OG Each complete all as specified.

S&F 63 A ,5 Pin (3 P+N+E) Metal Plug & Socket Enclosure for Three Phase connection all as specified and directed. Model:- DBMPS463SD, Make :-L&T or equivalent in Schinider and Legrand.

S & F MCB TPN 415 volts suitable for fixing in Industrial 3 Phase Socket 63 A complete all as specified and directed.Model:-BB40630D Make :-L&T or equivalent in Schinider and Legrand.

S & F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified.

S & F MCB Double Pole 20 Amps 240/415 Volt, confirms to IS/IEC 60898 Braeking Capacity of 10 kA, C-curve, complete all as specified and directed.Make- L&T, Cat No: BB20320C or equivalent in Schinder/ Legrand.

S & F MCB SP, 240 volts, 6A Amps 50 Hz ,confirms to IS/IEC 60898 Braeking Capacity of 10 kA, C-curve, complete all as specified and directed. Make -L&T,Model No-BB10320C/Schinder/ Legrand.

S & F wall mounted LED 18 watts ,Batten type T 8 light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including Ultra bright LED polycarbonate (T8) tube (Single side connection) 4' x 18 watts with G13 lamp holder complete all as directed by Engineer-in-Charge.Model -REGALBATTENT8UPTO1X18WDSBSWH For Batten Fitting and Model-PHOTONULTRAE2.01213T8SSTL18WLED865SPC For T8 Tubelight ,Make Havells, or equivalent in CG, Polycab, all as specifed and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 45 watts with pre wired and necessary mounting arrangements and provision of 3 mtr 2.5 sq mm 3 core copper conductor cable multi stranded from light fitting to over head line run through street light bracket and flexible pipe to connected to phase ,neutral and running earth wire and making good connection with suitable connectors to overhead conductor of any description complete all as directed by Engineer- in-charge. Make: Havells ,Cat No ENDURAPEARLNEOSL45WLED757SASYTOPC, or eqv in Surya or Crompton.

Excavation in trenches n exc 1.50 m wide and n exc 1.50 m depth in soft /loose soil and getting out for lying of cable and errection pipe etc complete all as directed.

Returning, filling in, trenches in soft /loose soil including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as directed.

Removal of excavated soil to a distance n. exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M & L sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation complete all as directed.

Supply & Laying well burnt brick , locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified.

Supply & Laying LT UG Cable of size 50 Sqmm 3.5 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed

S & F GI Tubing light grade of size 50mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clam as per site requirement etc all as specified and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 Flood light fitting luminaire, with system efficiency ≥110 lumen/W,AC120-300 V with high power LEDs as light source and Secondary lenses 10KV SPD included with high efficiciency electronic driver of capacity 80 watts, with pre wired and necessary mounting arrangement and provision of 4.00 sq mm three core flexable copper conductor cable multi stranded ,connected to existing points in Hanger beam angle of any description complete all as directed by Engineer- in-charge.Make: Make:Crompton, Cat No LFL-80-CDL/60-M, Model- PLUTO NEO, Make- CG or eqv in Havells/Crompton Greaves/Philips

Taking down ceiling fan/ Exhaust Fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv core PVC insulated PVC sheathed 3 core multistranded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.

M & L Submain wiring with 2 runs of single core 4 sqmm PVC insulated unsheated (FRLSH) multistranded 1100 volts grade with copper conductor drawn through and including non-metalic Rigid PVC Conduit ISI marked and its accessories including one run of single core 4.0 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board complete all as specified and directed.

M&L for replacement Sub main wiring 2 x 6 Sqmm multi-strand PVC insulated copper conductor unsheathed cable including concealed conduit and continuous earth wire of PVC insulated multi-strand copper conductor of size 6.0 sqmm complete all as specified and directed. Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

M & L Submain wiring with 4 runs of single core 10 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor drawn through and including non-metalic rigid PVC concealled conduit ISI marked and its accessories including two run of single core 10 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board complete all as specified and directed.

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I.

Sunrise Enterprise

Saraswati Auto Works