PROVISIONING OF CLUB ROOM FOR JCOS UNDER LBW, ADDITION AND ALTERATION TO FURNITURE STORE (P-57B) IN GE COMPLEX UNDER LBW AND SPECIAL REPAIR TO WALL OF BUILDING NO. P-44 UNDER SPECIAL REPAIR B/R AT NAVAL STATION BHEEMUNIPATNAM

Amount

Excavation in trenches n. exc 1.5 mtr wide and n. exc 1.5 mtr in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, taking out / laying UG cable etc. n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft /loose complete all as specified and as directed.

Excavation in trenches n. exc 1.5 mtr wide and exc. 1.5mtr in depth and n. exc 3.0 mtr in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 Sqm on plan and getting out in soft /loose complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated materials (soil) exc 250m and n. exc 500m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregates as in foundation filling and mass concrete complete all as specified.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sided and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surface of concrete completed all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular finishes rough surfaces of concrete.etc finished rough surfaces of concrete complete all as specified.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams finished rough surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs floor slab, landing and similar work not exceeding 200mm thick (Horizontal or sloping) in flat rough finished surface at concrete complete all as specified and as directed.

S&F 40mm thick flush shutter solid core construction, with block board core and plywood face panel, commercial type on both side covered with decorative face veneer with lipping/ frame to match complete all as specified and directed.

M&L well seasoned 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded on chamfered put together with glue pinned and joints complete all as specified.

M&L preparation of new wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

S&F solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed.

S&F 125 mm size MS butt hinges medium weight cold rolled fixed to frame complete all as directed.

S & F 150 mm size aluminium handles, cast type, anodised complete all as directed.

S & F 200 mm long, aluminium, anodised, barrel tower bolts of extruded section complete all as directed.

S & F 300mm long Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium allow complete all as specified and as directed

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc, (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S & F powder coated anodised aluminium window and ventilator shutters, Sliding type without sash bar, including necessary jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, roller, screws, anodised aluminium fittings such as suitable handle (01 No.) etc (thickness of powder coating not less than 50 micron) complete all as specified and as directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm each pane complete all as specified and as directed

S&F aluminium XPM wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

S&F anodised coloured aluminium grill of design No.DG-117, 10mm thick of DECOGRIL or equivalent make as approved by GE fixed with and including 'F' sections complete all as specified and as directed by the Engineer-in-Charge.

M & L reinforced cement concrete M-30 (Design Mix Concrete) using 20mm graded aggregate as in slabs supported on walls and the like complete all as specified and as directed.

M&L TMT bars 10mm dia and over, as reinforcement. cut to length, bent to shape required including cranking bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

M&L TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length , bent to shape required including cranking bending hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips complete all as specified.

M & L 40 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of floors complete all as specified and as directed.

M & L 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base/floor, complete all as specified and as directed.

M & L hardcore of broken stone or boulders of gauge n.exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface, complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection and paving finished cement concrete surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for moorum or red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L Brick work with fly ash bricks straight or curved on plan exc 6.0 mtr mean radius built in cement mortar (1:6) complete all as specified and as directed

M & L Brick Work in with fly ash Bricks straight or curved on plan to any radius in half brick thick wall, built in Cement Mortar 1:4 complete all as specified and as directed.

M&L for walling of random rubble uncourse, well bonded bedded and solidity hearted, build in CM (1:6) complete all as specified and as directed.

Cutting and removing weeds, shrubs and plants etc to carry out detailed survey complete all as specified and as directed.

M & L rendering 10mm thick on internal surfaces of brick wall or concrete surface in cement mortar 1:6 finished even and fair without using extra cement complete all as specified and as directed.

M & L rendering 15mm thick on fair faces of brick wall or concrete surface in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and as directed.

M&L rendering 5mm thick in cement mortar 1:3 as in ceiling finishing the surfaces even and fair without using extra cement complete all as specified and as directed.

M&L two coat of oil bound distemper over a coat of primer including preparation of new wall surfaces complete all as specified and as directed

M&L applying three coat of white wash on newly plastered ceiling surface including preparation of the surface complete all as specified and as directed.

M&L applying two coats of weather shield exterior emulsion paints over a coat of primer including preparation of new external wall surfaces complete all as specified and as directed.

M & L rendering 10mm thick on roof padding in cement mortar 1:3 finished even and fair without using extra cement complete all as specified and as directed.

M&L for normal water proofing treatment on roof slab portion consisting with the following operation : (i) Cleaning surface by wire brushes broom, removing dust and applying with bitumen primer conforming to IS 3384-1986 @ 0.50 kg per sqm (ii) Applying a tack coat of bitumen 85/25 @ 1.2 kg per sqm for water proofing membrane (iii) Applying of polymeric water proofing membrane weight not less than 3 kg per sqm over entire area with overlapping and sealed complete all as specified and as directed. (iv) Again applying hot bitumen 85/25 @ 1.2 kg per sqm over water proofing membrane (v) Applying a bituminous aluminium primer/ paint 0.10 kg per sqm complete all as specified and as directed.

S&F, stainless steel, curtain rod, 25 mm dia, complete all specified and as directed.

S&F fancy type CP knob round for fixing curtain rod complete all as specified and as directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 (Ist quality) as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 finished even and rough complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 350 x 250 x 7 mm/ 300 x 450 x 7mm/ 450 x 350 x 7mm thick (Ist quality) conforming to IS-13753, as in vertical surface such as skirting/dado set in neat cement slurry and pointed in coloured cement to match the surface, including 10mm thick rendering to receive tiles in CM (1:4) finished even and rough complete all as specified and as directed.

S&F grating doom 125mm dia of PTMT approved quality (minimum weight 40 gms) complete all as specified.

S & F vitreous china, water closet pedestal pattern (white) 'P' trap (including fixing bolt, low level flushing cistern of 10 ltr capacity and seat cover) complete all as specified and as directed.

S & F 15mm dia pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts. Screwed for iron pipe complete all as specified and as directed.

S & F 15 mm dia bib tap cast copper alloy chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as specified and as directed.

S & F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S & F 15mm dia stop valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed

S & F 15 mm dia two way bib cock chromium plated fancy type complete all as specified and as directed. (Jaquar Cat part No. FON-40041 or equivalent as approved by GE)

S&F 15mm bore Health faucet with 1.5m long easy flex tube in chrome finish and wall hook, complete all as specified and as directed

S & F rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top) Conforming to IS 12701-1996 three layered hoisted and fixed in position 750 ltrs capacity complete all as specified in SSR Part I complete all as specified and as directed.

S&F PP-R ball valves (brass insert) suitable for 25 mm bore PP-R pipe including connection & testing complete all as specified and as directed.

S&F PP-R gate valves (brass insert) suitable for 25mm bore PP-R pipe including connection & testing complete all as specified and as directed.

S&F three layer PP-R (Polypropylene random copolymer) pipes of outer dia 32 mm bore pipes SDR 7.4 & SDR 11 UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

All as per Srl item No. 59 here-in-above but for 25 mm dia

All as per Srl item No. 59 here-in-above but for 15 mm dia

S & F 40mm PVC (SWR) pipes single socketed in any length with rubber ring jointed to wall complete all as specified and directed.

S & F PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed.

S & F PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed.

M & L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) gully trap 110mm square or round mouthed type 'S' setting and jointing with solvent cement complete all as specified.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and as directed.

S&F stainless steel tubular towel rail 20mm dia, D type 600mm long between flanges of brass chromium plated fixed with and including CP brass screws complete all as specified and as directed

S & F soap dish, chromium plated, fixed to wall with plugs with chromium plated screws complete all as specified and directed

S & F Brass chromium plated shower rose 125 mm size with or without swivel joints including fixing to steel pipe or union complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in bed of drain including surface to be finished even and fair without using extra cement complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in wall of drain including surface to be finished even and fair without using extra cement complete all as specified and as directed.

M&L for boulder pitching, laid dry, hand packed tightly and grouting with cement sand mortar 1:6 complete all as specified and as directed.

All as per Srl item no. 76 here-in-before but except boulder

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 including gusset plate, including erection of vertical supports for holding purlins, rafters, base plates, nuts & bolts etc. complete all as specified and as directed.

M & L applying two coats of synthetic enamel paint over a coat of red oxide Zinc chromate primer including preparation of new steel surfaces over 10cm width or girth complete all as specified and as directed.

Demolition of Brick work or stone boulders masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed

Excavation over area, n.exc 1.5 deep and getting out in any type of soil complete all as specified and as directed

Removing excavated material from site to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre from the starting point complete all as specified.

M & L 50 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of floors complete all as specified and as directed.

M&L applying three coat of white wash on newly plastered wall surface including preparation of the surface complete all as specified and as directed.

M & L designer chequered cement concrete tiles rubber moulded 30 cm x 30cm x 25 cm thick with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors including 20mm thick screed bed or bedding layer of CM (1:4) complete all as specified and as directed

M&L Brick work with fly ash bricks straight or curved on plan exc 6.0 mtr mean radius built in cement mortar (1:4) complete all as specified and as directed

M & L rendering 15mm thick on fair faces of brick wall or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia drain pipe complete all as specified and as directed.

M&L for underground drainage double wall plain HDPE pipe 150 mm SN4 conforming to IS : 16098 (Part-II) single socketed in any length laid in trenches or in floors complete all as specified and as directed.

M&L precast reinforced cement concrete 1:2:4 type B-1 (Using 20mm graded stone aggregate) as in landings, cover slab (for manhole), chullah hood, chajjas, water trough, mangers, shelves etc and similar articles with plain faces set in CM 1:6 complete all as specified and as directed.

M & L providing cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as cast in situ in lintels upto 1.5m span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in coping complete all as specified and as directed.

Removing excavated materials (soil) exc 50 mtr and n. exc 100 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed

Demolition of reinforced cement concrete in roof, floors (other than ground level), beams, stair case, landing, chajjas and similar suspended work complete all as specified and as directed.

Demolition of cement concrete (Unreinforced) in ground floor and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed

Excavation over area, n.exc 1.5 deep and getting out in soft/ loose soil complete all as specified and as directed

M & L reinforced cement concrete M-30 (Design Mix Concrete) using 20mm graded aggregate as in foundations, including rafts, footings, plinth beams, bases for columns, etc. complete all as specified and as directed.

M & L reinforced cement concrete M-30 (Design Mix Concrete) using 20mm graded aggregate as in columns etc complete all as specified and as directed.

M & L reinforced cement concrete M-30 (Design Mix Concrete) using 20mm graded aggregate as in chajja etc complete all as specified and as directed.

M & L reinforced cement concrete M-30 (Design Mix Concrete) using 20mm graded aggregate as in beams, cantilever, bressumers, lintel over 1.5 mtr span etc complete all as specified and as directed.

M & L reinforced cement concrete M-30 (Design Mix Concrete) using 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished concrete surfaces complete all as specified and as directed

M&L 15 mm thick rendering on fair faces of brick/concrete surfaces in cement mortar 1:4 in two layers of 10mm thick and 5mm thick, finished fair and smooth and water proofing compound shall be added on top layer as per manufacturer instruction complete all as specified. (Note :- WPC will be measured and paid separately under appropriate item as supply only).

Supply only integral water proofing conforming to IS-2645-2003 complete all as specified.

M & L rendering 10mm thick on internal surfaces of brick wall or concrete surface in cement mortar 1:3 finished even and fair without using extra cement complete all as specified and as directed.

M&L applying two coats of weather shield exterior emulsion paints including preparation of old external wall surfaces complete all as specified and as directed.

M&L for preparation of new plastered / unplastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of oil putty with chalk whiting complete all as specified and as directed.

M & L hardcore of broken stone or boulders of gauge exc. 63mm but n.exc. 100mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface, complete all as specified and directed.

M & L 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate for sub base to floor/ path/ paver block etc complete all as specified and as directed.

S & F steel rolling shutter 1.25 mm thick of lath steel with ball bearing and safety lever lock mild steel, with 4 levers for rolling shutter as specified including top cover anchoring rod, hasp and staple and one coat of primer erected in position as indicated complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for fencing etc. and removing unserviceable materials from site of work complete all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to grade Fe-290W (Gde E-165) complete all as specified and as directed.

M&L for bands, straps, supports or stays for rainwater, ventilating pipes, hold fasts, wind ties, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F mild steel frame work as in doors or gates of angle or other section with gusset plates rails braces, etc (Fe-410-W Gde-E-250) quality -A complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and as directed.

Demolition of asbestos cement (corrugated, semi corrugated etc.) sheets in roof covering including AC ridge complete all as specified and as directed.

M&L machine cut polished kota stone slab flooring 20 to 25 mm thick over screed bed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M & L 15 mm thick screed bed or bedding layer of cement mortar (1:4) for laying floor finishes complete all as specified and as directed

S & F powder coated anodised aluminium window and ventilator shutters, side hung without sash bar, including necessary jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, roller, screws, anodised aluminium fittings such as suitable handle etc (thickness of powder coating not less than 50 micron) complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in coping complete all as specified and as directed.

M&L PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in surface channel and drain including necessary use and waste of form work complete all as specified.

M&L extra for forming fair finished drain or channel 60 cm inner girth in cement concrete using extra cement etc including forms, moulds , mitred / stopped ends complete all as specified.

M & L for factory made chequered cement concrete coloured tiles 300mmx300mmx25mm thick with grey cement and pigments, set jointed and pointed in neat cement slurry in floor complete all as specified and as directed.

Dismantling of wall and ceiling boards (fiber,pulp insulation etc) or insulation board /slab/blankets any thickness including cover fillets, including removing of dismantled material from work site all as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet in decorative pattern fancy type inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as specified and as directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed

M&L vitrified ceramic light shade tiles 10mm thick (Square/Rectangular) polished area of each tiles n.exc 0.36 Sqm as in floor etc. set and jointed in neat cement slurry and pointed in white and coloured cement to match the surface over and including screed bed layer 15 mm thick in CM 1:6 complete all as specified and as directed.

M&L vitrified ceramic light shade tiles 10mm thick (Square/Rectangular) polished area of each tiles n.exc 0.36 Sqm as in skirting etc. set and jointed in neat cement slurry and pointed in white and coloured cement to match the surface over and including 10 mm thick backing coat in CM 1:4 complete all as specified and as directed.

M & L for Non skid ceramic coloured tiles 6 to 7 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exc 0.09 (Ist quality) as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:6 finished even and rough complete all as specified and as directed.

M&L16-18mm thick granite (of any type) work table rubbed and polished in steps, jambs, pillars, window-sills, cooking platforms etc in cement mortar 1:4 bedded & jointed in neat cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M & L for rounding edges of stone slab, such as steps, cooking platform and other similar situation complete all as specified and as directed.

M&L cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed.

M & L reinforced cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roof, landings, deck slabs and in shelves and the like complete all as specified and as directed.

M & L Reinforced Cement Concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in chajjas, kerb, mud stone etc complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc built in cement mortar complete all as specified and as directed by the Engineer-in-Charge.

M&L repair to beam/ chajja/ drop/ facia (broken/ damaged), making good with PCC 1:2:4 type B1 or cement mortar 1:3, rendering 15 mm thick with using water proofing compound, sides and soffits in cement mortar 1:4 including necessary form work wherever damaged, including re-inforcement duly welded if required, including demolition of broken / loose PCC for taking down old plaster upto 8 mtr height complete all as specified and as directed.

M&L 100mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutter from the frame) each area n.exc 1.50 sqm each complete all as specified and as directed.

M&L TMT bars of 8mm dia and over, as reinforcement. cut to length, bent to shape required including cranking bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

M&L for complete removal of existing treatment on internal walls and applying two coat of oil bound distemper over a coat of primer complete all as specified and as directed

M&L one coat of oil bound distemper over a coat of primer including preparation of old ceiling surfaces complete all as specified and as directed

M&L applying two coats of weather shield exterior emulsion paints over a coat of primer including complete removal of existing treatment of old external wall surfaces complete all as specified and as directed.

M&L for preparation of new/ old plastered surfaces and applying 2mm thick layer of wall care putty complete all as specified and as directed.

M & L rendering 15mm thick on fair faces of brick wall or concrete surface in cement mortar 1:6 finished even and fair without using extra cement complete all as specified and as directed.

S & F rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top) Conforming to IS 12701-1996 three layered hoisted and fixed in position 500 ltrs capacity complete all as specified in SSR Part I including dismantling old existing tank complete all as specified and as directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 20mm dia iron pipe and fixed.(Minimum weight 455gm) complete all as specified and as directed

S&F in repair three layer PP-R (Polypropylene random copolymer) pipes of outer dia 32 mm bore pipes SDR 7.4 & SDR 11 UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

All as per Srl item No. 148 here-in-above but for 25 mm dia

All as per Srl item No. 148 here-in-above but for 15 mm dia

M&L cutting chases, pinning in, making good to facing were required and pointing in cement mortar 1:3 for concealed water tubing and making good cutting not exceeding 10cm girth complete all as directed.

S & F in repair 15 mm dia bib tap cast copper alloy chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as specified and as directed.

S & F in repair 15 mm dia two way bib cock chromium plated fancy type complete all as specified and as directed.

S & F in repair 15mm dia pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts. Screwed for iron pipe complete all as specified and as directed.

S & F in repair 15mm dia stop valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed

S&F in repair stainless steel tubular towel rail 20mm dia, D type 600mm long between flanges of brass chromium plated fixed with and including CP brass screws complete all as specified and as directed. (Jaquar Cat Part No. ACN-1111SM or equivalent as approved by GE)

S & F in repair vitreous china, water closet pedestal pattern (white) 'P' or 'S' trap (including seat cover) complete all as specified and as directed.

S&F in repairs vitreous china urinals, half stall type, white (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement , including fixing urinal spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and as directed.

S & F in repairs half pedestal wash basin vitreous china flat back/angle back white of size 550x400 mm including a pair of bracket cutting for pinning in ends of brackets or erecting stand including 32 mm dia CP waste coupling , PVC waste pipe 32 mm dia of standard length complete all as specified and as directed

S & F in repairs 3 hole basin mixer with pop up waste assembly, fancy type and connection with quarter turn fitting complete all as specified and as directed. (Jaquar Cat Part No: FLR-5191N or equivalent as approved by GE)

S&F in repair Health faucet CP with 1.0 m long easy flex tube in chrome finish and wall hook, complete all as specified and as directed. (Jaquar Cat Part No. ALD-565 or equivalent as approved by GE)

S&F in repair brass CP grating 100 mm bore complete all as specified and as directed.

S & F in repair brass CP towel ring round with round flange complete all as specified and directed. (Jaquar Cat Part No. ACN-1121N or equivalent as approved by GE)

S&F in repair toilet paper holder, brass CP fixed to walls with CP screws complete all as specified and as directed. (Jaquar Cat Part No. ACN-1151N or equivalent as approved by GE)

S & F in repair soap dish, chromium plated, fixed to wall with plugs with chromium plated screws complete all as specified and directed. (Jaquar Cat Part No. ACN-1131N or equivalent as approved by GE)

S&F in repairs corner glass shelf IVC (with bracket) complete all as specified and directed. (Jaquar Cat Part No. ACN-1173 or equivalent as approved by GE)

M&L for concealed point wiring with 1.5 Sqmm (nominal cross-sectional area) FRLS PVC insulated and unsheathed 1100 V grade multi stranded copper conductor single core cable drawn through and including 20 mm PVC conduit with all fittings and accessories including one run of FRLS PVC insulated and unsheathed single core multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity conductor to common earth and earth dolly including new pressed steel sunken boxes readily available (having thickness not less than 1.22 mm for boxes upto a size of 200 mm x 300 mm and beyond that the wall thickness shall not be less than 1.63 mm) concealed type with 3 mm thick bakelite sheet cover for mounting switches, sockets, fan regulator etc including testing complete all as specified and as directed for the following :- item Nos 169 to 173

All as per Srl Item No. 168 here-in-above but for One light point controlled by one, one way switch.

All as per Srl Item No. 168 here-in-above but for One Exhaust/ fan point controlled by one, one way switch 5 Amp and regulator

All as per Srl Item No. 168 here-in-above but for One socket outlet point 3 pin 5 A on independent board.

All as per Srl Item No. 168 here-in-above but for One switch socket outlet point 5 A on same board with other switches

All as per Srl Item No. 168 here-in-above but for one switch socket out let for 16 Amps 3 & 5 pin on independent board with 4.0 Sqmm cable and 4.0 Sqmm earth wire.

Supply and fixing switch piano flush button single pole one way 5 amps all as specified and as directed

Supply and fixing ceiling rose surface bakelite 65 x 30 mm three terminals all as specified and as directed.

Supply and fixing switch socket combination 2 in 1 3 pin, 5/15 amp flush type all as specified and as directed

Supply and fixing switch socket combination 2 in 1 3 pin, 5 amp flush type all as specified and as directed

Supply and fixing fan regulator electronic deluxe rotary step type complete all as specified and as directed.

S&F 1x18 watt indoor type retrofit batten type luminaries extruded polycarbonate / powder coated aluminum complete with LED retrofit T8 LED polycarbonate tube of capacity 18/19/20 watt with decorative holder and including connecting up with three core twisted flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and as directed. (Havells Cat part No. REGALBATTENT8UPTO1X22WSSBSWH (batten) and PHOTONULTRA1213T8SSTL18WLED865SPC (LED lamp) or equivalent as approved by GE)

S&F 1x18 watt indoor type luminaries extruded polycarbonate / powder coated aluminium complete with LED polycarbonate tube of capacity 09/10/12 watt with decorative holder and end cap and including connecting up with three core twisted flexible copper conductor cable of suitable size with taking down existing complete all as specified and as directed. (Havells Cat part No. LUMILINEBS9WLED865SPCWH or equivalent as approved by GE)

S&F energy saving & environment friendly long life 25 W, CT >= 5700 K, LED building security light made up of pressure die-cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance not less than IK-07 complete with integrated type, with high efficiency electronic driver, surge suppressor of 5 KV or more and high brightness LEDs, luminaire efficacy > 110 lumens / Watt, power factor >= 0.90 operating range – 140 to 270 V, 50 Hz complete including connecting up with and including twin / three core twisted flexible copper conductor cable of suitable size complete all as specified and as directed. (Havells Cat Part No. ENDURAPEARLSL25WLED757SASYTOPCMP or equivalent as approved by GE)

S&F street light bracket made out of 25 mm dia medium grade GI pipe bent to shape not exceeding 1.5 m long alongwith 2 nos clamp of size 25 x 4mm flat iron and including nut, bolts, washers suitable for fixing on building including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Supply and fixing sheet metal enclosure for MCB, DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 12 way with dim rail earth and neutral bar all as specified and as directed. Make: Legrand or equivalent as approved by GE

Supply and fixing in repair MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed. Make: Legrand or equivalent as approved by GE

Supply and fixing in repair MCB TPN of capacity 63 amps, 415 Volts C-series with 10kA breaking capacity all as specified and as directed. Make: Legrand or equivalent as approved by GE

M&L for earthing complete with galvanized steel earth plate electrode 600x 600 x 6.3 mm buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below ground level, connected to galvanized earth lead wire 4mm dia (upto 7.5 m in length from earth plate) by means of galvanized iron or steel bolts, nuts, check nuts and washers, and connected to equipments as directed, including funnel with GI med grade watering pipe 20mm bore, wire mesh charcoal or coke and common salt in alternate layers, of 15cm compacted thickness all around the earth electrode, with concrete pit in PCC 1:3:6 type C-1, 50mm thick pre cast RCC 1:2:4 type B1 cover slab reinforced with 8mm dia reinforced bar 15cm C/C and earth lead handle protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50m and necessary testing complete all as shown on electrical plate No. 3 of MES SSR Part-I and as directed

Supply, installation, testing and commissioning of Heavy Duty exhaust fan 300 mm sweep, 900 RPM, single phase, 230 Volts, AC, 50 Hz and connecting up with 1.5 sqmm copper conductor flexible wire from ceiling rose complete including louvers and provision of hold fast for fixing fan and louver shutter with cutting of hole and necessary PCC (1:3:6) and making good the disturbed surfaces (if any) complete all as specified and as directed.

S&F for ceiling fan 230 Volts 1200mm sweep, 5 STAR rating complete incl fan hook made out of 16 mm dia mild steel hook with all accessories including taking down old ceiling fan and kept in MES store yard with necessary accessories complete all as specified and directed. (Make : Havells Model No. Samraat 50 HS or equivalent as approved by GE)

Material and labour for XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 4 core laid in trench /poles/on wall and all as specified and as directed

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt bricks, Sub class 'B' bricks of size 230 x 115 x 75 mm best quality locally available laid flat, dry in trenches for cable protection complete all as specified and as directed.

M&L for cutting to existing road/ PCC drain for taking out/ laying UG cable and including necessary earth work and making good to match with the existing surface with PCC 1:3:6 type C1 using 20 mm graded stone aggregate complete all as specified and as directed.

Material and labour for galvanized iron tubing 25 mm bore light grade with all fitting for protection of FRLS cable, laid in trenches/wall/floor including necessary clamp, bolt/nut if any all as specified and as directed.

Taking down carefully existing aluminium conductor point wiring (light / fan / socket or power point) complete, with all fittings such as switches, socket, regulator, ceiling rose, utility light fittings and lamp holders etc and removing materials from site and making good the disturbed surfaces of walls, roof and floor etc as per existing specification complete all as specified and directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and fan regulators etc. for reuse at site complete all as specified and as directed. (Note : To be measured only when found serviceable in all respects complete for reuse)

M&L for concealed Sub main wiring with two run of 6.00 Sqmm (nominal cross-sectional area) FRLS PVC insulated and unsheathed 1100 V grade multi stranded copper conductor single core cable drawn through and including PVC medium grade conduit of 25 mm dia with all fittings and accessories concealed in walls, floors and ceilings complete including one run of FRLS PVC insulated and unsheathed single core multi stranded copper conductor cable of size 6.00 Sqmm as earth continuity conductor connected to common earth and earth dolly for main DB to sub DB including cutting chases pinning in making good to facing and pointing in using cement mortar 1:3 to the ends with taking down old unserviceable sub main wiring and making good the disturbed surfaces complete all as specified and as directed. NOTE: 3 runs of 6 Sqmm and one run of PVC concealed conduit 25mm dia will be measured as one unit i.e. RM

S & F Switch modular flush type single pole one way 6 Amp, 250 volt , complete all as specified and as directed.

Fixing only Switch flush button single pole one way 5 Amp, 240 volt , complete all as specified and as directed. (Note : Material obtained from Srl item No. 195 here in before shall be used)

S & F Switch flush button single pole two way 5 Amp, 240 volt , complete all as specified and as directed.

S & F modular plate switch flush type single pole one way 16 Amp, 250 volt , complete all as specified and as directed.

M&L modular socket 6 Amps 5 pin complete all as specified and as directed.

Fixing only switch socket outlet 5 Amps flush type complete all as specified and as directed. (Note : Material obtained from Srl item No. 195 here in before shall be used)

M&L modular socket 6-16 Amps 2/ 3 pin combined shutter complete all as specified and as directed.

S&F modular step type fan regulator 120 watt two module five steps and back plate complete all as specified and as directed.

S&F modular plate white colour suitable for flush metal boxes for mounting modular switches or sockets etc for 8 modules complete all as specified and as directed.

All as per Srl Item No. 205 here-in-above but for 6 modules

All as per Srl Item No. 205 here-in-above but for 3 modules

All as per Srl Item No. 205 here-in-above but for 2 modules

S&F flush metal box 1/2 module complete all as specified and as directed.

All as per Srl Item No. 209 here-in-above but for 6 modules

All as per Srl Item No. 209 here-in-above but for 3 modules

All as per Srl Item No. 209 here-in-above but for 8 modules

Fixing only ceiling rose, surfaces bakelite three terminal complete all as specified and as directed. (Note : Material obtained from Srl item No. 198 here in before shall be used)

S&F of MCB, DB, TPN, 4-ways, DOUBLE DOOR, IP-43, Ik-09 with metal door, rated bus bars, earth bar, neutral links complete including blanking plates as required and fixed flush to wall / other surface complete all as specified and as directed.

S&F of MCB, DB, SPN, 8-ways, DOUBLE DOOR, IP-43, Ik-09 with metal door, rated bus bars, earth bar, neutral links complete including blanking plates as required and fixed flush to wall / other surface complete all as specified and as directed.

Supply and fixing in proper position MCCB four pole of capacity 100 amps, 415 Volts 25kA breaking capacity all as specified and as directed.

S&F MCB, FP, rupturing capacity 10 kA, ‘C’ curve, 63 Amp, 415 volts ISI marked complete all as specified and as directed.

Supply and fixing MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed. Make: Legrand or equivalent as approved by GE

S&F MCB, DP, rupturing capacity 10 kA, ‘C’ curve, 40 Amp, ISI marked complete all as specified and as directed.

S&F single pole and neutral enclosure with two pin earth plug with 01 Nos of MCB DP 20 Amps 'C' series complete all as specified and as directed.

Supply and fixing indoor luminaire decorative batten for wall/ceiling mounting box type Extruded aluminium housing ,PC Diffuser, energy efficient saving LED BATTEN LIGHT 20W,230 V,50 HZ, slim integrated design easy install including twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed. [Make:CG Cat Part no.CCS-100-20-65-HL2-DP-NWH or equivalent as approved by GE]

S&F Recess Mounting luminaries LED down lighter of 28/30 W white in the shape of Square complete all as specified and as directed. (Havells Cat Part No. PLUTONEO2X2PLR28WLED857S or equivalent as approved by GE)

S&F Recess Mounting luminaries LED down lighter of 12 W white in the shape of Square complete all as specified and as directed

S&F 10 Watt LED decorative CITY 3 wall/ surface mounting polycarbonate body suitable for retrofit LED lamp base B22 including lamp complete all as specified and as directed. (Make : Havells Model No. LHDL06160099 or equivalent as approved by GE)

S&F LED mirror light fittings 07 watt, 230 volt, 50 Hz suitable for indoor and outdoor applications complete all as specified and as directed.

S&F water heater (Geyser) storage capacity 25 ltrs vertical type 5 star rated along with electric wiring 04 Nos GI Anchor bolts 12mm dia, 100mm long nuts and washer complete all as specified and as directed.

S&F AC single phase static electronic KWH energy meter of accuracy class 1.0, 240V, 50 Hz with Backlite LCD display of rating 10-60 Amp six months history with transparent hinge type box complete all as specified and as directed. (Make : HPL Model No. SPPL15200100002OC00 or equivalent as approved by GE)

S&F exhaust fan 300 mm sweep PVC body, 230 Volts single phase AC with louver shutter/ grill including 3 core copper cable from ceiling rose to exhaust fan & required hold fast, cutting holes on walls of suitable size complete all as specified and as directed. (Make : Havells Cat No. Ventil Air-DX white or equivalent as approved by GE)

M&L for earthing complete with 7.5m CI pipe 80 mm dia with flanged ends, centrifugally cast, class A, in any length, joints with stainless steel nuts and bolts and sufficient slot upto 2.5 mtr length buried directly and preferably vertically in ground with top flanged ended 2.5 mtr below ground level welded/ connected with GI strip 32 x 6 mm size on the top edge of the flange to bottom edge of the flanged for earthing including filling the pit with charcoal common salt surrounding the earth pipe including drilling 400 mm dia bore any strata of soil to lower the CI pipe complete all as specified and as directed.

S A R CONSTRUCTIONS

LEE INFRAS