Balance work for construction of 1st Floor Teaching Block BBA and BCA Block for S.C.V.B Govt. Degree College at Palampur Distt. Kangra (HP) (SW- Balance work of Main Building and Water Supply and Sanitary Installation)

Amount

Providing form work with steel plates of 3.15mm (Three decimel one five milimetre (Three decimel one five milimetre thick, welded with angle iron in frames of 30mmx30mmx5mm (Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and balconies and acess plat form the like floor etc. as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing form work with steel plates of 3.15mm (Three decimel one five milimetre thick, welded with angle iron in frames of 30x30x5mm, (Thirty into Thirty into Five millimeters) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing form work with steel plates 3.15mm (Three decimel one five milimetre thick welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto all heights of propping and centring below supporting floors and removal of the same for in-situ-reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls under 20cm(Twenty centimetre) wide in all width as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1cement : 1.5 coarse sand) : 3 graded stone aggregate20 mm (Twenty milimetre)nominal size) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm (Twenty milimetre)nominal size) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1cement : 1.5 coarse sand) : 3 graded stone aggregate20 mm (Twenty milimetre)nominal size) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Steel reinforcement for reinforced cement concrete work including strengthening, cutting, bending, binding and placing in position complete and binding all complete above plinth level TMT bar grade Fe-500, as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :CM 1:6 (One cement : Six Sand) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.with CM 1:4 ( One cement : Four Sand) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

12 mm thick one side Pre-laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - 1, medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade -1, Type II marked : as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing cup board shutters 25 mm (Twenty five milimetre) thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm (Twenty five milimetre) wide x12 mm (Twelve milimetre) thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charg as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately).Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 18 mm thick confirming to IS:14587 as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing 6 mm (Six milimetre) thick ply wood lining with butt jointing and nails ( frame work and cover fillets to be measured and paid for sepertely) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of : (Note:- Butt hinges and necessary screws shall be paid separately) 12 mm thick plain grade -1, medium density flat pressed three layer particle board FPT -I or graded wood particle board FPT- I, IS : 3087 marked, bonded with BWP type synthetic resin adhesive as per IS : 848 as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing aluminium hanging floor single rubber door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. Complete, as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. Complete Size 65 mm (Sixty five milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to steel windows by welding as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm ( Three hundred into sixteen milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :150x10 mm (One hundred fifty into ten milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 asper IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. Complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

125mm (One hundrted twenty five milimetre)

75 mm (Seventy five milimetre)

Providing and fixing oxidised M.S. casement stays(straight peg type) with necessary screws etc. complete, 200mm (Two hundred milimetre) weighting not less then 120gms. as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Precast terrazo tiles 22 mm (Twenty two milimetre)thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm (Twenty milimetre)thick bed of cement mortar 1:4 (1 cement:4 coarse sand) :Medium shade pigment using 50% white cement and 50% ordinary cement as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Chequerred precast cement concrete tiles 22 mm (Twenty two milimetre)thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm (Twenty milimetre)thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) Medium shade pigment using 50% white cement, 50% ordinary cement as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Precast terrazo tiles 22 mm (Twenty two milimetre)thick with graded marble chips of sizes upto 12 mm, in skirting and risers of steps not exceeding 30 cm in height, on 12 mm thick cement plaster 1:3 (1 cement : 3 coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete with tiles of Medium shade pigment using 50% white cement and 50% ordinary cement as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm (One hundred ten milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm (Twenty milimetre)nominal size) and cost of cutting holes and making good the walls etc. :100 mm (One hundred milimetre)as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimetre) gap for thermal expansion. as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Bend 110 mm (One hundred ten milimetre)

Shoe 110 mm (One hundred ten milimetre)

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete asn per the direction of Engineer-In-charge, as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing M.S. channels for doors, windows, frames manufactured from M.S. section 40mmx75mmx4mm with M.S. flat 75mmx4mm in combination as per drawing and design including hinges, jamb, lock jamb beed and if required thrashold i/c thrashold of M.S. angles means lugs, with split and tails to each jamb including iron butt hinges 2.5mm thick with a provision of locking arrangement and shock observers as specified and applying a coat of approved steel primer after pre-treatment of the surface , as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints, vented and welded with 16mmx3.15mm (Three decimel one five milimetre lugs 10cm long embedded in cement concrete block 15cmx10cmx10cm (fifteen centimeter into ten centimeter into ten centimeter) size of 1:3:6 (One cement : three sand: Six stone aggregade 20mm (Twenty milimetre) nominal size or with wooden and screws of rawl plugs and screws or with fixing clips or with belts and nuts as required and iron fittings including providing and fixing of glass pans with glazing clips and special metal sesh butt of approved make complete including applying a priming coat of red lead paint as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Fixed steel Windows

Providing and fixing factory made double steel shutter side hungs ( one glazed and one wire gauge)of standred rolled steel sections, jointing mitered welded with manufactured to relevant ISI standred specification with steel plugs and screws or rawl plugs screws or with fixing clips or with bolts and nuts as required and iron fitting i/c providing and fixing glass pans with special putty of glazed side of shutter and wire gauge of IS desgination 85G with metal beading on other side complete i/c priming coat of red lead paint as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Prividing and fixing railing for stair case having baluster of 40x40mm square hollow MS pipe SWG-16 gauge with a clear height of 85 cm @ 60 cm center to center jointing in cement concrete step and jointing with electric / gas welding at top along with hand rail of hollow MS pipe of 50 mm dia(SWG-18) vertical baluste welding/ jointed with each other with 2 Nos MS flat of 50x5 mm complete with applying priniming coat of red lead paint as per specification and direction of Engineer in charge as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (Three hundred into three hundred milimetre) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm (Twenty milimetre)thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete as per specification and direction of Engineer in charge as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood), as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

6 mm cement plaster to ceiling with Cm 1:3 (One cement: Three sand) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing 12 mm ( Twelve milimetre) thick water proof panes ISI marked and 1.00 mm thick aluminum sheet upto 100 mm ( One hundred milimetre) towards toiltet side with frame DD wood as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

15 mm (Fifteen milimetre) cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

White washing with lime to give an even shade New work (three or more coats) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Distempering with oil bound washable distemper ofapproved brand and manufacture to give aneven shade:New work (two or more coats) over and including water thinnable priming coat with cement primer as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (Twenty milimetre)(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand)Flush / Ruled/ Struck or weathered pointing as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing G.I. pipes complete with G.I. Fittings including trenching and refilling etc. :15 mm (Fifteen milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing G.I. pipes complete with G.I. Fittings and clamps, i/c cutting and making good the walls etc as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

15 mm (Fifteen milimetre)

20 mm (Twenty milimetre)

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main 15 (Fifteen milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (One hundred milimetre) sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cistern, includingflush pipe, with manually controlled device (handle lever)conforming to IS : 7231, with all fittings and fixturescomplete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C.pan of size 580x440 mm (Five hundred eighty into four hundred forty milimetre) with integral type foot rests as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm (Four hundred thirty into twohundred sixty into three hundred fifty milimetre) or 340x410x265 mm (Three hundred forty into four hundred ten into two hundred sixty five milimetres) sizes respectively, as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :Flat back wash basin of size 550x400 mm (Five hundred fifty into four hundred milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for then reception of pipes and fittings as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing rubber plug for wash basin or sink 32 mm (Thirty two milimetre) Dia as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing CP brass waste for wash basin or sink 32 mm (Thirty two milimetre) Dia as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing M I Union for wash basin or sink 32 mm (Thirty two milimetre) Dia as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing CP brass S trrap for wash basin or sink 32 mm (Thirty two milimetre) Dia as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing CP brass 32 mm (Thirty two milimetre) dia Bottel trap of approved quality and mke as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing 600x450 mm (Six hundred into four hundred fifty milimetre) beveled edge mirior supperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm (Six hundred milimetre) long towel rail with total length of 645 mm, (Six hundred forty five milimtre) width 78 mm (Seventy eight milimetre) and effective height of 88 mm (Eight eight milimetre), weighing not less than 190 gms as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing toilet paper holder C.P. Brass as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing chromium plated brass soap dish of Jaguwar or contra with C.P. brass brackets fixed to wooden cleats with C.P. brass screws as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm (Fifteen milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 1500 (Fifteen milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm (Fifteen milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing uplasticised PVC connection pipe with brass unions 450 mm (Four hundred fifty milimetre) length 15mm (Fifteen milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing G.I./ M I Union as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

15 mm (Fifteen milimetre) nominal size

20 mm (Twenty milimetre)nominal size

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor etc. Complete. as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

110x90 mm (One hundred ten into ninety milimetre)

110x75 mm (One hundred ten into seventy five milimetre)

Providing and fixing high pressure PVC spigot and socket soil, waste and ventilating pipes ISI Marked i/c fixing with approved adhesive etc. Complete. as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

150 mm (One hundred fifty milimetre) Dia

Providing and fixing PVC Single Equal Branch with oval asses Door ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete i/c fixing with approved adhesive etc. Complete. as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC door bend with oval acess door intersection rubber washer 3 mm thick bolta and nuts ISI Marked i/c fixing with approved adhesive etc. Complete 110 mm (One hundred ten milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

Providing and fixing PVC Single Equal Branch with oval asses ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete i/c fixing with approved adhesive etc. Complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC coller ISI Marked insertion rubber washer 3 mm thicK bolt and nuts complete i/c fixing with approved adhesive etc. Complete.

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC Plain bend with oval asses ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete i/c fixing with approved adhesive etc. Complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC offset 45° ISI Marked i/c fixing with approved adhesive etc. Complete, as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals .

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC duel Double Equal Branch with oval asses ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete i/c fixing with approved adhesive etc. Complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC plain Double Equal Branch ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete i/c fixing with approved adhesive etc. Complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC Y Junction with oval acess door intersection rubber washer 3 mm thick bolta and nuts ISI Marked i/c fixing with approved adhesive etc. Complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC plain Double Equal Junction ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete i/c fixing with approved adhesive etc. Complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

75 mm (Seventy five milimetre) Dia

110 mm (One hundred ten milimetre) Dia

Providing and fixing PVC P or S trap for water closet squating pan ISI Marked insertion rubber washer 3 mm thick bolt and nuts complete i/c fixing with approved adhesive etc. Complete. 110 mm (One hundred ten milimetre) as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.10 litre (full flush) capacity-white as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

Providing and fixing 100mm dia CP iron grating of ESS-KSS for nalhni trap, as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

Providing and laying cement concrete 1:5:10 (One cement: FIve sand: ten graded crushed/broken stone aggregate) 40mm (Forty milimetre) nominal size in PVC. pipes of the 150 mm internal diameters i/c concrete for bedding necessary form work and curing complete as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

Constructing masonry Chamber 60x60x75 cm (Sixty into sixty into seven five centimetre) inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design ,as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge as per the satisfaction of Engineer-in-charge including carriage of materials within all leads and lifts of materials and other incidentals.

TANUJ SHARMA