OPEN GYM AND BEAUTIFICATION WORK at KUNNALKAD WARD-4 MARADU MUNICIPALITY

Amount

CIVIL WORKS

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.2 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

od293228/2023_2024 : Providing and fixing 60x30x2 cm or nearest available size Granite stone block Flamed surface on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

od293229/2023_2024 : Supplying and fixing machine finished granite stone sitting bench of 1.5 m length, slab thickness not less than 50 mm, 450 mm clear height from ground level, 450 mm wide sitting slab, 450 mm wide back rest including cost of conveying, loading, unloading,material and labour charges etc. complete as per the direction of departmental officers.

od293230/2023_2024 : Providing and fixing Entrance pergola using Natural stone (SHELL WHITE) using, granite stone (Smooth finish) 15X15X240cm - 4 nos for Pergola Pillars, granite stone (Smooth finish) 240X7.5X15cm - 2 nos for Pergola Beams, granite stone (Smooth finish) 240X5X15cm - 6nos for Pergola Rafters including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293231/2023_2024 : Designing and Fixing Inauguration/signage Board including cost of board, lettering, fixing, conveying etc all complete As per the Direction Of Departmental officers

od293232/2023_2024 : WALKER SINGLE- Providing and fixing Walker single- FNF 004 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe- for MAIN FRAME, minimum 32 NB GI B-CLASS Pipe- for LEG FRAME, Minimum 25 NB GI B-CLASS Pipe for HANDLE FRAME, NYLON 66 INJECTION MOULDED CASING CLAMPS, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" FOOT REST, Nylon 66 injection Moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293233/2023_2024 : RIDER- Providing and fixing Rider - FNF 002 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe- for MAIN FRAME, Minimum 32 NB GI B-CLASS pipe for SEAT FRAME, Minimum 40 NB & 25 NB B CLASS GI B-CLASS Pipe for HANDLE FRAME, Minimum 32NB & 25NB GI B-CLASS pipe with two handles for LEG REST, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for FOOT REST & SEAT REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293234/2023_2024 : STEP TRAINER- Providing and fixing Ski trainer - FNF 007 (Make FUN PLAY )using, Minimum 100 NB G.I. C CLASS pipes for MAIN FRAME, Minimum 40 NB G.I. pipe for FOOT REST PIPE, Minimum 40NB & 25 NB G.I. pipe for HANDLE, Minimum 25 NB & 40 NB GI B-CLASS Pipe for CONNECTING PIPE, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for FOOT REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293235/2023_2024 : CHEST PRESS CUM SHOULDER PRESS- Providing and fixing Chest press cum shoulder press - FNF 016 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe for CENTER FRAME, Minimum 40 NB & 32 NB GI B-CLASS Pipe for MAIN FRAME, Minimum 32 NB & 25 NB GI B-CLASS Pipe for HANDLE FRAME, Minimum 32 NB & 25 NB & 40 NB GI BCLASS Pipe for CONNECTING PIPE, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for SEAT & BACK REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293236/2023_2024 : LEG PRESS- Providing and fixing Cycle - FNF006 (Make FUN PLAY )using, 25 NB & 40 NB GI B-class Pipe for MAIN FRAME, 32 NB GI B-CLASS Pipe for SEAT FRAME, 25 NB GI B-CLASS Pipe for HANDLE FRAME, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293237/2023_2024 : CYCLE- Providing and fixing Cycle - FPSPCL208 (Make FUN PLAY )using, 25 NB & 40 NB GI B-class Pipe for MAIN FRAME, 32 NB GI B-CLASS Pipe for SEAT FRAME, 25 NB GI B-CLASS Pipe for HANDLE FRAME, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293238/2023_2024 : SHOULDER TWIRL NEW- Providing and fixing Bench with fix weight - FPSPCL247 (Make FUN PLAY )using, 100 NB G.I C-Class pipe for main frame, 32 NB G.I B-Class pipe for Bench frame, 20 NB G.I B-Class pipe for Handle frame, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293239/2023_2024 : LEG EXTENTION- Providing and fixing Cycle - FNF020 (Make FUN PLAY )using, 25 NB & 40 NB GI B-class Pipe for MAIN FRAME, 32 NB GI B-CLASS Pipe for SEAT FRAME, 25 NB GI B-CLASS Pipe for HANDLE FRAME, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293240/2023_2024 : ABB TRAINER- Providing and fixing ABB Trainer - FPSPCL187 (Make FUN PLAY )using, Minimum 80 NB GI B-class Pipe for MAIN FRAME, Minimum 32 NB GI B-class Pipe for SIDE FRAME, Minimum 25 NB G.I. PIPES for INTERMEDIATE PIPE, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od293241/2023_2024 : ONE SEATING CUM 2 STANDING TWISTER- Providing and fixing Tai chi cum twister - FPSPCL215 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe for MAIN FRAME, Minimum 25 NB GI B-CLASS Pipe for HANDLE FRAME, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for TWISTER DISC, Minimum 25 NB & 20 NB GI B-class Pipe for SEATING FRAME, Minimum 80 NB GI B-class Pipe for SEATING FRAME STAND, Minimum 80 NB GI B-CLASS Pipe for TWISTER STAND, Minimum 25 NB GI B-CLASS Pipe for TWISTER HANDLE FRAME, LLDP Plastic- TWISTER DISC, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

BUILD OWN ASSOCIATES (BID ID -2107426)

P. M Abdul kareem (BID ID -2107956)