MAINTENANCE AND REPAIRING WORK OF VARIOUS SCHOOL BUILDINGS LOCATED AT KANSAD, KANAKPUR, SACHIN, PARDI KANDE, IN AREA OF SOUTH ZONE -B (KANAKPUR) , SURAT.

SN ITEM Unit QTY SOR 24-25 TOTAL

Excavation for foundation includ.sorting out & stacking of useful materials & disposing of the

excavated stuff upto 50 mt. Lead & all lift, watering etc. Comp. (A) Loose or Soft soil

1 Executed With Mechanised Efforts / Machinaries

(1) Up to 1.5 Mt. depth C.M. 15.00 123.13

Excavation for foundation includ.sorting out & stacking of useful materials & disposing of the

excavated stuff upto 50 mt. Lead & all lift, watering etc. Comp. (A) Loose or Soft soil

Executed With Manual Labours

(1) Up to 1.5 Mt. depth C.M. 15.00 212.52

3 Providing & Laying C.C1:5:10 (1cement :5coarse sand :10 graded stone agg. 40 m.m Nominal C.M. 15.00 2,606.92

size )& curing comp. excl. cost of from work in :Foundation & Plinth

Providing & laying cement concrete 1:4:8 (1 cement:4 coarse sand:8 graded stone agg. 40 mm

4 nominal size) & curing comp. excl.cost of form work in (A) Foundation and Plinth C.M. 5.00

5 Providing & laying C.C 1:3:6 (1cement :3 coarse sand :6 Crushed stone agg 20m.m Nominal C.M. 5.00 3,095.25

size)&curing comp. excl. cost of form work in :(a) foundation & Plinth

6 Providing & laying cement concrete 1:1.5:3 (1 cement:1.5 sand:3 graded stone agg. 20 mm C.M. 5.00 4,250.50

nominal size)& curing comp. Includ.cost of form work but exclu. Cost of reinforcement for

reinforced concrete work in : (A) Foundation, footing, Base of columns and Mass concrete.

Providing & laying ordinary cement con.1:1.5:3 (1cement:1.5sand: 3 graded stone agg. 20 mm

nominal size) finishing smooth curing etc. comp. Incld. Cost of form work but excl. Cost of

7 reinforcement for R.C.C. Work in : Up to G.L./P.L. (A) COLUMNS:

(1)Having c/s area up to 0.08 s.mt C.M. 5.00 12,844.32

(2) Having c/s area more than 0.08 sq. mt. & upto 0.12 sq.mt C.M. 5.00 11,166.97

(3) Having cross sectional area more than 0.12 sq. mt. C.M. 5.00 9,201.68

(1)Having c/s area up to 0.08s.mt C.M. 5.00 9,102.61

(2) Having c/s area more than 0.08 sq. mt. & upto 0.12 sq.mt C.M. 5.00 8,174.41

(3) Having cross sectional area more than 0.12 sq. mt. C.M. 5.00 7,086.88

Providing & fixing IS Mark TMT Bar FE 500D reinforcement for R.C.C. work incl. bending,

8 binding & placing in position etc. comp. Upto G.L./P.L. Kg. 2000.00

Brick work using common burnt clay building bricks having crushing strength not less than 35

9 kg./Sq.Cm. in foundation and plinth in Cement C.M. 10.00

Mortar 1:6 (1- Cement : 6 -fine sand)(C) Fly Ash Bricks

10 Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in C.M. 130.39 136.92

layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and

11 Filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness C.M. 289.06 301.78

including watering, ramming and consolidating etc. complete.

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level

consisting of 12mm thick backing coat of C.M. 1:3

12 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1- sand) etc. complete. S.M. 330.88

13 Providing & laying ordinary cement con. 1:1.5:3(1cement:1.5sand:3 graded graded stone

agg. 20 mm nominal size) finishing smooth curing etc. comp. Incl.. Cost of form work but

excl. Cost of reinforcement for R.C.C. Work in :

(1)Having c/s area up to 0.08 s.mt- Ground Floor C.M. 0.50 12,844.32

First Floor C.M. 0.50 12,885.28

Second Floor C.M. 0.50 12,926.24

Terrace (third) Floor C.M. 0.50 12,967.19

(2) c/s area more than 0.08sq. mt. & upto 0.12 sq.mt - G.F C.M. 0.50 11,166.97

First Floor C.M. 0.50 11,207.92

Second Floor C.M. 0.50 11,248.88

Terrace (third) Floor C.M. 0.50 11,289.83

(3) Having cross sectional area more than 0.12 sq. mt. -- G.F C.M. 0.50 9,201.68

First Floor C.M. 0.50 9,242.63

Second Floor C.M. 0.50 9,283.59

Terrace (third) Floor C.M. 0.50 9,324.54

(1)Having c/s area up to 0.08s.mt- Ground Floor C.M. 0.50 9,102.61

First Floor C.M. 0.50 9,143.56

Second Floor C.M. 0.50 9,184.52

Terrace (third) Floor C.M. 0.50 9,225.47

(2) Having c/s area more than 0.08 s.m. & upto 0.12 s.m - G.F C.M. 0.50 8,174.41

First Floor C.M. 0.50 8,215.36

Second Floor C.M. 0.50 8,256.32

Terrace (third) Floor C.M. 0.50 8,297.27

(3) Having cross sectional area more than 0.12 sq. mt. -- G.F C.M. 0.50 7,086.88

First Floor C.M. 0.50 7,127.84

Second Floor C.M. 0.50 7,168.79

Terrace (third) Floor C.M. 0.50 7,209.75

(2) Slabs having more than 8cm. and upto 10 cm. Th'.- G.F C.M. 0.50 7,984.42

First Floor C.M. 0.50 8,025.37

Second Floor C.M. 0.50 8,066.33

Terrace (third) Floor C.M. 0.50 8,107.28

(3) Slabs having more than 10 cm. & upto 13 cm. Th'.- G.F. C.M. 0.50 7,396.96

First Floor C.M. 0.50 7,437.92

Second Floor C.M. 0.50 7,478.87

Terrace (third) Floor C.M. 0.50 7,519.83

(4) Slabs having more than 13 cm. Thickness -- G.F C.M. 0.50 6,813.01

First Floor C.M. 0.50 6,853.96

Second Floor C.M. 0.50 6,894.92

Terrace (third) Floor C.M. 0.50 6,935.87

(D) LINTELS: -- G.F C.M. 0.50 9,982.37

First Floor C.M. 0.50 10,023.32

Second Floor C.M. 0.50 10,064.28

Terrace (third) Floor C.M. 0.50 10,105.23

(E) CHAJJAS: -- G.F C.M. 0.50 5,576.81

First Floor C.M. 0.50 5,617.76

Second Floor C.M. 0.50 5,658.72

Terrace (third) Floor C.M. 0.50 5,699.67

Providing & laying ordinary cement con. 1:1.5:3(1cement:1.5sand:3 graded graded stone

agg. 20 mm nominal size) finishing smooth curing etc. comp. Incl.. Cost of form work but

14 excl. Cost of reinforcement for R.C.C. Work in :

(A) Stair cases including landings etc.

Ground Floor C.M. 1.00 7,698.11

First Floor C.M. 1.00 7,739.06

Second Floor C.M. 1.00 7,780.02

Terrace (third) Floor C.M. 1.00 7,820.97

(B) Vertical and horizontal fins

Ground Floor C.M. 1.00 11,613.07

First Floor C.M. 1.00 11,654.03

Second Floor C.M. 1.00 11,694.99

Terrace (third) Floor C.M. 1.00 11,735.94

Providing & fixing IS Mark TMT Bar FE 500d reinforcement for R.C.C. work Kg. 500.00 77.29

incl. bending, binding & placing in position etc.comp.---Ground Floor

First Floor Kg. 200.00 78.34

Second Floor Kg. 200.00 79.39

Terrace (third) Floor Kg. 200.00 80.44

Brick work using common burnt clay building bricks having crushing strength not less than 35 C.M. 5.00 4,729.83

kg./Sq.Cm. in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(C) Fly Ash Bricks

16 Ground Floor

First Floor C.M. 2.00 5,018.55

Second Floor C.M. 2.00 5,307.27

Terrace (third) Floor C.M. 2.00 5,595.99

Half brick masonry in common brunt clay building bricks having crushing strength not less

17 than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 - coarse sand ) in foundation and plinth S.M.

(C)Fly Ash Bricks

Ground Floor S.M. 10.00 712.81

First Floor S.M. 10.00 719.37

Second Floor S.M. 10.00 725.94

Terrace (third) Floor S.M. 10.00 732.50

Uncoursed rubble masonary with hard stone of approved quality in

18 foundations and plinth in cement mortar 1:6 (1 Cement : 6 sand) including leveling up etc. C.M. 10.00

19 Pointing on Coursed stone masonary with cement mortar 1:3 (1 cement : 3 Sand) ---(A) Flush S.M. 97.04 101.89

(B) Ruled Pointing S.M. 100.22 105.24

20 Pointing on Uncoursed stone masonary with cement mortar 1:3 (1 cement : 3 Sand) ---(A) S.M. 104.99 110.24

(B) Ruled Pointing S.M. 108.81 114.25

Providing Rubble Pitching with hard stone of approved quality in cement

21 mortar 1:6 (1 Cement : 6 Coarse sand) including leveling up ,Curing etc. complete C.M.

excluding pointing

22 Providing and filling rubbles including hand packing and filling interstices with quarry spalls C.M. 10.00 1,094.11

behind abutments and between returns as directed.

Providing upto floor two level precast cementconcrete jali or grill 1:2:4 mix (1- Cement : 2-

coarse sand : 4-graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia. Mild

steel wire including roughening,cleaning, fixing and finishing in cement mortar 1:3 and curing

complete. (B) 40mm thick. Ground Floor

First Floor S.M. 10.00 752.39

Second Floor S.M. 10.00 762.85

Terrace (third) Floor S.M. 10.00 773.32

Providing & Applying 10mm.th.cement plaster in single coat on brick/ concrete walls

similar surfaces for plastering & finished even & smooth with a floating coat of cement slurry

24 mixed with admixture of lime or neeru in required proportion etc. comp. in C.M 1:3 (1 S.M. 10.00

cement : 3sand) (A) For wall

and similar surfaces -- Ground Floor

First Floor S.M. 10.00 228.84

Second Floor S.M. 10.00 258.39

Terrace (third) Floor S.M. 10.00 287.94

(B) For ceilings &soffits of stairs

Ground Floor S.M. 15.00 225.34

First Floor S.M. 15.00 254.89

Second Floor S.M. 15.00 284.45

Terrace (third) Floor S.M. 15.00 314.00

Providing & Applying 15mm.th.cement plaster in single coat on brick/ concrete walls

similar surfaces for plastering & finished even & smooth with a floating coat of cement slurry

25 mixed with admixture of lime or neeru in required proportion etc. comp. in C.M 1:3 (1 S.M. 25.00

cement : 3sand) (A) For wall

and similar surfaces -- Ground Floor

20mm thick sand faced cement plaster on walls for height more than 10 metres above

ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm

26 thick finishing coat of C.M. 1:1 (1-cement : 1- sand) etc. complete. S.M. 50.00

Providing 20 mm thick double coat mala cement plaster on brick / concrete work for

plastering comprising of base coat 12 mm thick cement plaster in cement mortar (1

Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 (1

Cement : 2 Coarse sand) finished with trovel including scaffolding curing etc. complete.

Providing & Applying 20mm. Th. Heavy Roller plaster on walls or similar surfaces at all

floor levels consisting of 12 mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) & 8 mm. th.

Finishing coat of C.M. 1:1 (1 cement: 1 sand) apply thick cement slurry and apply roller

horizontal as well as vartical ( two times ) up to good quality and size of grain in elevation as

per directed by engineer incharge.

29 Providing throating or plaster drip and moulding it to R.C.C. chajja etc. comp.. For all R.M. 41.66 43.74

30 Providing 20 mm deep finished groove in plaster in line and level etc. Comp. For all R.M. 50.00 50.00

Providing and laying precast terrazo tile 20mm thick white,black, white and black (or of

the colour specified in specification of tender item) marble

chips of sizes upto 6mm laid in floors, treads of steps and landings on a bed of 25mm average

thickness of Lime mortar 1:1.5(1-Lime putty : 1.5 coarse sand) or C.M. 1:6 (1:cement :6 -

31 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles S.M. 25.00

rubbing and polishing complete with precast tiles of.(A) Light shades using white cement

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of

cement mortar 1:6 (1-cement : 6-coarse sand) or

L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry

32 mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. S.M. 20.00

Providing and laying polished kota stone slab 25mm thick in risers of steps,skirting Dedo

and pillars laid on 10mm thick cement mortar 1:3 (1- Cement : 3 coarse sand) and

jointed with gray cement slury mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete.

Providing & Laying white glazed tiles 6mm. th. of Orient, Kajaria,

Jhonson,Nitco,Somani ,Bell make at all floor levels, in flooring, treads of steps & landings

34 laid on a bed of 12 mm. Av. Th.C.M.1:3(1cement :3 sand) finished with flush pointing in white S.M. 10.00

cement etc.com. For all floors

Providing & Laying white glazed tiles 6mm. th. Of Orient, Kajaria,

Jhonson,Nitco,Somani,Bell make at all floor levels in skirting risers of steps & dado on 10 mm.

35 th. C.M.1:3(1cement :3 sand) including necessary cement paste for fixing and joined with S.M. 10.00

white cement slurry etc. complete. For all floors

Providing and laying Ceramic tiles 6mm thick in flooring treads of steps and landing laid on a

bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing

36 in white cement. S.M. 10.00

Providing and laying Ceramic tiles 6mm thick in skrting risers of steps and dedo on

10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement

37 slurry S.M. 10.00

38 Providing & laying marble stone slab flooring over 20 mm.av. base of C.M.1:6 ( 1 S.M. 10.00 2,246.54

cement :6 coarse sand ) & jointed with grey cement slurry incl. rubbing & polishing

comp.(A) Marble slab 25 mm. Thick.

Providing & laying granite slab 18mm thick in flooring, treads of steps and landing

laid on bed of 20mm thick cement mortar 1:6 (1 Cement : 6 coarse sand) or lime mortar

39 1:1.5 laid and finished with flush pointing in white or colour cement including rubbing and S.M. 10.00

polishing complete. ( Basic Rate:-

Providing & laying granite slab 18mm thick in skirting, risers of steps, dedo and

pillars laid on 10mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) and finished

40 with flush pointing in white or colour cement including rubbing & polishing comp.. (Basic S.M. 10.00

Rate:- Rs.1347.46/S.M.)

Providing & laying granite slab 18mm thick in Window-Door seal Frame Etc laid on 10mm

thick cement mortar 1:4 (1 Cement : 4 Coarse sand) with nessary adhesive material and finished

with flush pointing in white or colour cement, including rubbing & polishing comp.. (Basic Rate:-

42 Labour Charges For Edge Finished For Granite R.M. 200.00 43.43

Providing & laying Vitrified tiles of 8mm thick of Orient, Kajaria, Jhonson, Nitco, Somani,

Bell, Asian or Euro make in flooring,treads of steps & Landing laid on bed of 20 mm

(Average) base of cement mortar 1:6 (1 Cement : 6 Coarse sand) on new surface or fixing

on existing flooring by adhesive material including dismentaling of existing flooring and

43 jointed with colour cement slurry including finished with flush pointing & cleaning the S.M. 10.00

surface etc. comp.Size 24" x 24"

For Antiskid tiles

44 Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x 24" in flooring treads of steps and Sqm. 10.00 1,092.37

landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) finishing with

flush pointing in white cement.

45 Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x 24" in skrting risers of steps and Sqm. 10.00 1,135.80

dedo on 10mm thick cement plaster 1:3 (1 cement : 3 coarse sand) and jointed with white

46 Providing and laying Vitrified tiles 8 to 10 mm thick, 36" x 36" in flooring treads of steps and Sqm. 10.00 1,531.82

landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) finishing with

flush pointing in white cement.

47 Providing and laying Vitrified tiles 8 to 10 mm thick, 36" x 36" in skrting risers of steps and Sqm. 10.00 1,592.40

dedo on 10mm thick cement plaster 1:3 (1 cement : 3 coarse sand) and jointed with white

Providing and laying chequered precast concrete tiles 22mm thick with aggregate of

sizes upto 6mm in floors treads of steps and landing on 20mm thick bed of C.M. 1:6 (1

48 cement : 6 sand) or L.M. 1:1.5 (1 Lime putty : 1.5 sand) jointed with neat cement slurry with S.M. 100.00

pigments to match the shade of the

49 Providing and laying rough chiseled dressed stone flooring over 20mm thick base of S.M. 100.00 576.79

cement mortar 1:5 (1 cement : 5 coarse sand) or L.M. 1:1.5 including pointing with

cement mortar 1:2 (1 cement : 2 stone dust) etc.

Providing and laying cement concrete flooring 1:2:4 (1 cement : 2 course sand : 4 graded

50 stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat

(A) 40mm thick S.M. 100.00 319.03

(B) 50mm thick S.M. 100.00 374.14

Providing & fixing 35mm.th. Flush Door Solid Double Core type Both Face water proof Ply

Vennered & 1.5 mm th.laminate shall be pasted on both side with adhesives as specified by

the manufacturers. The laminate shall be as per approved shade & texture, of make incl. Sal

wood frames of finished size 12cm x 7cm.incl. S.S. Hinges with nessary screws &

aluminum fixtures & fastenings For all Floor

52 Same as Above But Without Frame S.M. 20.00 2,520.00

Providing & fixing 35mm.th. Indian teak wood shutters for doors, windows & clearstory

windows incl. Indian teak wood frames of finished size 12cm x 7cm.incl. anodized

53 aluminum fixtures & fastenings incl. Primer coat of approved quality & two coats of oil S.M. 5.00

painting etc. For all Floor (A) Fully Panelled

(B) Partly Panelled and Partely Galzed S.M. 5.00 5,185.03

(C) Fully Galzed S.M. 5.00 4,836.39

54 Providing and fixing 35mm thick shutters for Doors, windows and clearstory windows S.M. 5.00 4,101.06

including anodised alluminium butt hinges with necessary screws.

(A) Indian teak wood. (i) Fully Panelled.

Providing and fixing FRP FRAME size 125 x 65 mm and 35 mm thick FRP shutter with wood

grain raised panneled design finish shutter having extra reinforcement on sides & edges in Gel

coat finish. The core of the shutter & frame is to be filed up with injected polyurethene foam

done in situ along with embedded wooden pieces for stiffening & also taking hinges & fixtures.

55 The whole FRP frame & shutter is to be water proof weather proof,termite proof &resistance to S.M. 10.00

mild acid/alkali. Rates are to be inclusive of S.S.hinges with fastener sleeve & alluminium

fixtures & fastentings.

Providing and fixing FRP of 35mm thick Fiber Glass shutter with 1.5 to 2.0 mm thick fire

retardent grade FRP skin in depressed panel design having extra reinforcement on sides &

edges & in Gel coat finish. The core of the shutter is to be filled up with injected retardent grade

56 foam done in situ alongwith embedded wooden pieces for stiffening & also taking hinges & S.M. 5.00

fintures. The whole FRP frame & shutter is to be water proof

,weather proof, termite proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S

hinges with necessary screws & alluminium fixtures & fastenings.

Providing & fixing M.S.Grills of required pattern to wooden frames of windows etc. At all floor

levels with M.S. flats at required spacing & frame around square or round bars with round

57 headed bolts & round headed bolts and nuts or by screws incl. Priming coat of Red lead paint Kg. 100.00

etc. comp. (A) Plain grill For all Floors

Providing & fixing in position collapsible steel shutters with vertical channels

20 x10 x 2 mm. Braced with flat iron diagonals 20 x5mm size with top & bottom rails of

58 T-iron 40x40x6mm. with 38mm dia. steel pulleys comp. with bolts, locking arrangements, S.M. 5.00

stoppers, handles incl. applying a priming coat of Redlead paint etc. comp.

Providing and fixing M.S. Fan clamps type 1 to 16 mm dia M.S. bar bent to shpe with hooked

59 ends to RCC slabs curing, layig including painting the exposed portion of loops, all as per Each 130.00

standard design complete.

Providing & laying ordinary C.C.1:1.5:3 mix for R.C.C. work incl. boxing, centering,

vibrating, curing & mixed with approved water proofing cement compound or

"CEMWET"or"PIDICRETE LW"integral water proofing admixture as water proofing agent to

be mixed with 50 kg. cement bag shall be as recommended by the manufacture of the

water proofing material, concrete work for top, bottom slab & side pardi for Under

ground Tank & Item incl. Necessary excavation & refilling the available earth, 15 cm th' C.C

1:4:8 for bedding concrete, Half B.M. in C.M. 1:4 outside wall, inside R.C.C. pardi as per design,

60 10mm.th. water proofing cement plaster in C.M. 1:3 with smooth finishing,watering

etc.Comp.to all inner face & bottom of tank curing etc. comp. incl. Locking arrangement,

outlet, inlet, overflow & wash out pipe arrangement as necessary & C.I. Cover 0.60 x .045

weight not less then 35kg. etc. com. as per structural drawing excluding Steel & as directed by

Engineer- in-charge

Underground tank Lit. 1000.00 6.87

Providing and filling in depressions of Bath and W.C. At all floor levels, after

61 completing plumbing work of pans, pipes,traps etc.with cinder or fly ash as directed by C.M. 10.00

Engineer in charge etc. comp..

62 NOTE :- (1) The whole work is to be executed through specialized agency with a

guarantee of 10 (Ten) years given on a prescribed proforma duly stamped (2) The rate

shall include for work at all floors & conducting water

proof test as directed. (M.R.)

(A) Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C.,kitchen and the like consisting of :

(a) I course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS : 2645 in recommended proportions.

(b) II course of a layer of plaster in C.M. 1:3 with water proofing compound confirming to

IS:2645 about 25 mm. th' in the floor of the depression & about 18mm th' On the side walls of

the depression up to the floor level, water proofing plaster about 18 mm. th' be continued on

the walls above the floor level for a height of 600 mm. with surface suitable to receive further S.M. 20.00

(c) Finishing top with stone aggregate 10mm to 12mm nominal size spreading @0.008

C.M./S.M., thoroughly embedad in plaster layer.

as per specifications & instructions of Engineer in charge (Cement consumption 0.316 Bags /

(B) Providing and laying integral cement based water proofing treatment including

preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of

following operations.

(a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed

with proprietary water proofing compound comforming to IS:2645 over the R.C.C. slab

including cleaning the surface before tratment.

(b) Laying cement concrete using broken bricks/brick bats 25 mm to 100 mm size with 50% of

cement mortar 1:5 (1 Cement : 5 Coarse sand) admixed with proprietary water proofing

compound conforming to IS:2645 ,brick bats is finally covered by jointless cement plaster S.M. 10.00

20mm th. in C.M. 1:4 added with special water proofing compound confirming to IS:2645 & top

smooth finished with trowel with false chequered marking of 300 mm.size.The treatment is

carried along the vertical surface of the parapet & other adjoining wall up to height of about

300 mm in a shape of quarter round vata Incl. curing etc. Comp. With average thickness of

mm and minimum thickness at khurra as 65 mm.

(c) The whole terrace so finished shall be flooded with water for a minimum period of two

weeks for curing and for final test. All above operations to be down in order and as directed and

specified by the engineer-in-charge. With average thickness of 120 mm and minimum thickness

at khurra as 65 mm. (Cement consumption 0.511 Bags / S.M.)

Proiding & laying water proofing treatment to vertical and horizontal surfaces like consisting

of (a) I course of applying cement slurry 4.4 kg per sq.mt. mixed with water proofing compound

confirming to IS:2645 in rcommended proportions. (b) II corse of 20mm cement plaster 1:3

mixed with water proofing compound in recommended proportion (c) III course of applying

63 blown or / resideal bitumen applied hot at 1.7 kg per sqm of area. (d) IV course of 400mm S.M. 10.00

micron th. PVC sheet. (Overlaps at joints of PVC sheet should be 200mm wide and pasted to

each other with bitumen about 1.7 kg./ sqm.)

64 Providing & fixing G.I. Rain water spout of 50 mm.dia & 30 cm length etc. No. 10.00 101.91

65 Providing & fixing at all floor levels,both face polished machine cut edge green kota S.M. 10.00 900.00

stone slab (30mm) for urinal partition joined with grey cement slurry (1:1) incl. Rubbing &

polishing etc. complete. (M.R.)

66 Providing & fixing at all floor levels,both face polished machine cut edge Marble slab for S.M. 10.00 1,050.00

urinal partition joined with grey/White cement slurry (1:1) incl. Rubbing & polishing etc.

complete. (M.R.)( Basic Cost- Rs. 450/S.M.)

WATER SUPPLY AND SANITARY ITEMS

Prov.& Fixing water closet squatting pan (Indian type W.C.pan) at all floor

levels, size 580mm incl. 100 mm size "P'or "S" trap for water closet squatting pan joining the

67 trap with the pan & soil pipe in C.M. 1:1 (1cement :1 fine sand) etc. Comp.(A) Vitreous No. 10.00

china long pattern of approved colour For all

68 Providing and fixing Wash Down Water closet European type W.C. pan with integral P or S Each 10.00 1,356.81

trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1 find sand)

(seat and cover to be measured and paid for separately) (A) Viterous china pattern - I (i) in

approved colour

69 Providing and fixing plastic seat and cover for wash down water closet with Each 291.33 291.33

C.P. brass hinges and rubber buffers (B) Plastic seat and cover.

Providing & fixing wash basin with single hole for pillar tap at all floor levels, with C.I. or M.S.

Brackets painted white incl. cutting holes & making good the same incl. fittings such as pillar

tap, capstan head screw down high pressure with screws, shanks & back nuts, C.P. Brass waste

70 trap, screw down stop tap 15 mm. dia. etc. complete. (A) Vitreous china flat back wash basin No. 10.00

550 mm.x 400 mm. size in approved colour For all Floor

Providing & fixing Urinal or approved quality including conecting the Urinal

71 with waste pipe, tap etc. complete. (A) White earthenware flat back or corner type size 430 mm Each 10.00

Providing & fixing 600 mm.x 450 mm. mirror of superior glass at all floor

72 levels, mounted on 6 mm. th. A.C. sheet or plywood sheet & fixed to wooden plugs with C.P.brass No. 10.00

screws and washers etc. For all Floor

Prov. & Fixing S.W. Gully trap with C.I.grating brick masonary (C.M 1:5)chamber &

water tight C.I. cover with frame of 300mmx300mm size (inside) with weight includ.

73 plastering smooth inside & outside 15mm. th' in C.M.1:3 etc. comp. (i) Square mouth traps--- No. 10.00

(A) 100mm x 100mm Size -P type

(B) 150mm x 100mm Size- P Type No. 10.00 1,246.92

Prov. & Fixing S.W. Gully trap with C.I.grating brick masonary (C.M 1:5)chamber & No. 10.00 1,098.05

water tight Pre cast R.C.C. cover of 300mmx300mm size (inside) includ. plastering smooth

inside & outside 15mm. th' in C.M.1:3 etc.

comp. (i) Square mouth traps---(A) 300mm x 300mm Size -P type

(B) 150mm x 100mm Size- P Type No. 10.00 1,052.77

Prov. & Fix. 10 cm.x15 cm.(4" x 6") S.W. trap with Inside dimension ,455 x 610 mm & 450

mm deep sewer trap chamber with 23 cm th' B.B. masonary walls in C.M 1:5 with cement

plaster 15 mm th' in C.M. 1:3 inside & outside to exposed faces, R.C.C. top slab with 1:2:4 mix (

75 cement: 2 Sand : 4 Grade stone aggregate 20mm size) ,Foundation concrete 1:5:10 & fixing C.I. No. 10.00

cover with frame to be not less than 38 kg. On top etc. comp. for single pipe.

.(A).Same as above but Precast RCC heavy duty Cover instead of C.I. Cover No. 10.00 2,915.61

Extra for every additional depth of 0.1 mt beyoung 0.45 mt Each 10.00 233.85

Providing & construction simple chamber of 23 cm. th' B.B. Masonary in C.M 1:5 with cement

plaster 15 mm th' in C.M. 1:3 inside & outside to exposed faces, R.C.C. top slab with 1:2:4

76 mix ( 1 cement: 2 Sand : 4 Grade stone aggregate 20mm size) ,Foundation concrete No. 10.00

1:5:10 & fixing C.I. cover with frame to be not less than 38 kg. On top etc. comp. Inside

dimension,455 x

610 mm &450 mm deep for single pipe

(A) Same as above but Precast RCC heavy duty Cover instead of C.I. Cover No. 10.00 2,681.76

Extra for every additional depth of 0.1 mt beyoung 0.45 mt Each 10.00 242.39

77 Providing, Lowering & laying joining R.C.C. NP2 CLASS Pipe In C.M. 1:1 of

following nominal internal diameters incl. Testing of pipes and joints etc. Comp

Providing & laying in trenches galvanised mild steel tubes(medium grade) TATA / ZENITH /

78 ASIAN / JINDAL MAKE of the following nominal bore & tube fittings etc. comp..- 25mm.dia. R.M. 10.00

Providing & Fixing to wall, ceiling floor at all floor levels, galvanised mild steel

tubes(medium grade) TATA / ZENITH / ASIAN / JINDAL MAKE of the following nominal bore,

79 tube, fittings & clamps incl. making good the wall ceiling and floor etc. complete. R.M. 50.00

(A) 15 mm. dia.

Providing & Fixing C.P. Brass screw down bib tap at all floor levels, polished bright etc. comp.- No. 10.00 186.83

80 (A) 15mm dia. For all Floors

Providing & Fixing gun metal check or non return full way wheel valve at No. 10.00 186.83

all floors levels, etc. complete. (A) 15 mm. dia.

81 Providing & Fixing chromium plated brass half turn flush cock at all floor No. 10.00 263.77

levels, of approved quality incl. fixing in pipe line etc. Comp.-- 25 mm dia.

82 Providing & Fixing abonite ball cock of approved qualities directed etc. No. 10.00 102.91

comp. (A) 25 mm. dia.

83 Providing and fixing C.I. Machinehole cover 0.60 x 0.45 mt. Size having No. 10.00 958.17

weight not less than 35 Kg. etc. complete.

Providing & Fixing U-PVC pipe (SWR) confirming to IS no. 13592 (Type "B") of

Prince/Supreme/Jain/Astral/Tulsi/Finolex make for soil and waste discharge system

84 at all floor levels incl. All fixtures like bends, tees, shoe etc. jointed with resin of approved R.M. 50.00

brand & manufacture etc. comp. (M.R.) (a)

Providing & fixing U-PVC pipes Confirming to IS no. 13592 (Type "A") of R.M. 50.00 203.00

Prince/Supreme/Jain/Astral/ Tulsi/Finolex make for rain water at all floor levels incl.

fixtures like bends, tees, shoe etc joined with resin of approved

brand & manufacture etc. comp. (M.R.) (A) 75 mm. Dia.

Providing, Laying and jointing on true line and level UPVC pipe (SCH-40) line of

Prince/Supreme/Jain/Astral/ Tulsi/Finolex make including fittings make or equivalent

as approved by angineer-in-charge. Pipe shall be fixed on the wall the help of clamp at every

86 two meter C/C or shall be concealed as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent, including cost of all

Providing & Fixing P.V.C. pipes (SCH-80) of Prince/ Supreme/ Jain/ Astral/ Tulsi/Finolex

make for water supply line at all floor levels incl. fixtures like bends, tees, shoe etc joined

with resin of approved brand & manufacture etc. comp. Pipe shall be fixed on the wall the help

87 of clamp at every two meter C/C or shall be concealed as directed including necessary

fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent,

cost of all materials.

88 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 110x110 mm diameter with jali NO 20.00 586.27

of the following nominal diameter of self cleaning design with

C.I. scread down or hinged grating including the cost of cutting and making good the walls.

89 Providing & Fixing in position PVC Cowl vent to pipes of

Prince/Supreme/Jain/Astral/Tulsi/Finolex make etc.Comp. (A) 75 mm. dia. NO 20.00

Providing & fixing M.S. Holder Bat clamps at all floor levels of approved

90 design to C.I. Or S.C.I pipes including the cost of cutting holes & making good the wall etc. No. 20.00

Complete - 100 mm. dia. (M.R.)

Providing & fixing G.I./Aluminum Patti clamps at all floor levels of approved

91 design to C.I. Or S.C.I pipes including the cost of cutting holes & making good the wall etc. No. 20.00

Complete - 100 mm. dia. (M.R.)

Providing erecting and fixing double coated Sintex/Super/Reno PVC (ISI) mark water

92 tank of required capacity each with all necessary fittings & connection etc. complete on Lit. 10000.00

Providing & Fixing Kathi around the vertical PVC drainage pipes for

93 concealing with cement plaster 20 mm avg thickness(CM 1:3 [1 cement :3 coarse sand])

finishing as per instruction given by Eng. incharge. for

(A) 75 mm PVC PIPE R.M. 50.00 173.00

(B) 100 mm /110 mm PVC PIPE R.M. 50.00 180.00

ITEMS FOR COMPOUND WALL & OTHER MISC. ITEMS :-

Boring holes 3.5 mt.deep in ordinary soil ( for cast in situ piles) & disposal of

94 the surplus excavated soil as directed within a lead of 50 M. For following diameter of

95 Providing & laying cement concrete 1:2:4 (1 cement:2 sand:4 graded stone agg. 20 mm C.M. 5.00 3,741.69

nominal size)& curing comp. Includ.cost of form work but exclu. Cost of reinforcement for

reinforced concrete work in : (A) Foundation, footing, Base of columns and Mass

Providing & laying ordinary cement con.1:2:4 (1cement:2sand: graded stone agg.

20 mm nominal size) finishing smooth curing etc. comp. Incld. Cost of form work but excl.

Cost of reinforcement for R.C.C. Work in :

Up to G.L./P.L. (A) COLUMNS:

(1)Having c/s area up to 0.08s.mt C.M. 1.00 12,335.51

(2) Having c/s area more than 0.08 sq. mt. & upto 0.12 sq.mt C.M. 1.00 10,658.16

(3) Having cross sectional area more than 0.12 sq. mt. C.M. 1.00 8,692.87

(1)Having c/s area up to 0.08s.mt C.M. 1.00 8,593.80

(2) Having c/s area more than 0.08 sq. mt. & upto 0.12 sq.mt C.M. 1.00 7,665.60

(3) Having cross sectional area more than 0.12 sq. mt. C.M. 1.00 6,578.07

Providing & laying C.C 1:3:6 (1cement :3 coarse sand :6 crushed stone agg. 20 m.m Nominal

97 size)& curing comp. incl. cost of from work in: wall caps/ C.M. 1.00

Steel work welded in built up sections, framed work including cutting, hoisting, fixing in

position and applying a priming coat of red lead paint

(A) in beams & joists channels angles, tees, flats with connection plates or

angle cleats as in main & cross beams,hip & trussed purlins connected to common raffers Qtl. 5.00

(B)For work like chain link fencing, above compound wall etc. Qtl. 5.00 9,108.48

(C)in trusses & trussed purlins upto 25m.Span &15m.Overall height Qtl. 5.00 10,197.11

99 Providing and fixing G.I. chain link of 50mm x 50mm size x 10 guage thick with nuts, bolts, SM 100 311

washer or G.I. pins, excluding M.S. angles etc.complete as per relevent IS specification &

directed by engineer in charge. (TATA or Jindal

Providing and fixing hot dip Concertina coil of 610 mm dia. made out of

2.59mm (12 SWG) hot dip galvenized (G.I. coating not less than 200 gm/sq.m) th. wire

having 80 nos. of spikes and 200 nos. of clip made out of stainless steel (AISI 304 1.5 mm th. dia.,

G.I. strips 0.5 mm th. (C.I. coating not less than 120 gm/sq.m.) weight of one coil should not be R.M. 300.00

less than 15 kg. etc. complit, at the top of compound wall fixed with S.S. clips and binding

wires wherever necessary etc. complit. (Note :- Stretching lehgth of one coil should not be more

100 Providing and fixing and fitting TATA or Jindal make G.I. barbed wire fencing with necessary Kg. 200.00 125.00

barbed wire (12 x 14 guage, weight not less than 0.14 kg. / mt.) pins, hooks, excluding M.S.

angles etc. complete as per relevent IS specification.& directed by engineer in charge

Providing & fixing colouron galvaniced steel, zinc / aluminium allus coated sheet 0.5 mm.

thick roofing fixed with gslvanised grom J or L hook bolts and bolt 8mm dia with bituman

101 and impet washer filled with white lead etc. Excluding the cost of purlins rafter and trusses. S.M. 20.00

(Tata / Jindal or equivalent)

Providing corrugated G.I. Sheets of class-3 roofing fixed with glavanished iron J or L Hooks,

Bolts and nuts 8m diameter with bitumen and G.I. limpet washer or G.I. limpet washer. filled

102 with white lead complete excluding the cost of purlins, Rafters and Trusses. (1) 0.80 mm S.M. 20.00

thick sheet. (Tata / Jindal or

Providing corrugated G.I. Sheets of class-3 roofing fixed with glavanished iron J or L Hooks,

Bolts and nuts 8m diameter with bitumen and G.I. limpet washer or G.I. limpet washer. filled

103 with white lead complete excluding the cost of purlins, Rafters and Trusses. (1) 0.63 mm S.M. 20.00

thick sheet. (Tata / Jindal or equivalent)

Providing & fixing 150mm wide 450mm over all semicircular plain G.I. sheet class-3

gutter with iron brackets 40mm x 3mm size bolts, nuts, washers etc. including marking

104 necessary connection with rain water pipes. R.M. 50.00

(i) 0.8 mm thick

Providing ridges or hips 600mm over all in plain G.I. sheet fixed with G.I. "J" of "L" hooks

105 bolts and nuts 8mm dia G.I. limpet and bitumen washer R.M. 50.00

complete (1) 0.80 mm thick

Providing & fixing 150mm wide 450mm over all semicircular plain G.I. sheet class-3

gutter with iron brackets 40mm x 3mm size bolts, nuts, washers etc. including marking

106 necessary connection with rain water pipes. R.M. 50.00

(i) 0.63mm thick

Providing ridges or hips 600mm over all in plain G.I. sheet fixed with G.I.

107 "J" of "L" hooks bolts and nuts 8mm dia G.I. limpet and bitumen washer complete (1) R.M. 50.00

0.63mm thick sheet

Providing & Fixing UV stabilise FRP Sheet roofing with overlapping the main cladding on both

edges. All fixing holes must be predrilled oversize as specified for the sheet length and fastener

being used. Fasteners must be fitted with approved washers. Fixings should be tightened to

ensure a weatherproof seal but they must not be over tightened Side-lap fasteners must also be

installed at specified centers with the FRP sheet having clearance holes provided as per the

108 main fasteners Weatherproofing shall be provided at all flashing points under the normal

flashing by the fitting of a foam closure strip to match the profile being used. Closure strips will

be sealed to the sheet with an appropriate non setting silicone sealant. Excluding the cost

of purlins rafter and trusses.

(a) 1.5 mm thick SM 20.00 992.00

(b) 2 mm thick SM 20.00 1,100.00

Providing & Fixing Polycarbonate sheet roofing with surface of the sheet is coated with an

anti-UV Co-extrusion layer having good weather resistance, it can maintain its optical properties

and mechanical performance for a long time. Fasting is usually done by screws. , The fastening

screws should be inserted about 500 mm apart and 300mm apart Along the supporting

internal purlin and edge pulin.All fixing holes with diameter at least 2 mm larger than screw

109 must be predrilled into each screw location. The screws should be 6mm diameter with length

according to sheet thickness and corrosion resistant, with at least heavy duty hot dripped

galvanized or stainless steel. Excluding the cost of purlins rafter and trusses.

(a) 1.5 mm thick Solid Sheet SM 10.00 1,261.00

(b) 2 mm thick Solid Sheet SM 10.00 1,510.00

110 Providing & Fixing 80 mm dia M.S. pipe as vertical post are beded in 1:1.5:3 concrete also R.M. 10.00 750.00

horizontaly in line and connecting to purline angle etc by welding rereting etc. (a) Medium

111 Providing & Fixing 50 mm dia M.S. pipe as vertical post are beded in 1:1.5:3 concrete also R.M. 10.00 485.00

horizontaly in line and connecting to purline angle etc by welding rereting etc. (a) Medium

Providing & fixing black board on walls of 1.8mt.x1.2mt size made up to 12 mmth.B.W.P

.Plywood (Brand Saras,Kitply,Uniply, Anchor, Green,Wood Stock or century) fixed with teak

wood beading of 65 mmx 50mm size, rubbing & sanding comp., incl. applying two coats of black

112 board paint over a priming coat on plywood & French polishing the frame all round etc. No. 5.00

Comp. as per instruction of Engineer in charge (M.R.)

Providing & fixing Green board on walls of 1.8mt.x1.2mt size made up to 18 mm th.ply

(using IS 710 Marin ply) with 1 mm thick outside green board & 0.8mm backside white

laminate & with good Quality of adhesive with appropriate fittings of Alluminium fittings

or teak wood bedding 65 mmx 50mm size, rubbing & sanding comp., as per instruction of

Engineer in charge (M.R.)

114 Providing & fixing White board on walls of 1.8mt.x1.2mt size of 12mm thick with appropriate No. 5.00 4,230.00

fittings and Alluminium fittings comp., as per instruction of Engineer in charge (M.R.)

Providing & Fixing Reading table size 8' x 4' and height 2'-6" with table top 18mm thick

(Brand Saras,Kitply,Uniply, Anchor, Green,Wood Stock or century) commercial plywood with

1.0mm thick lamination sheet fitting with teakwood moulding table top supported on 3" x 3"

115 teakwood leg & 3" x 11/2" teakwood framing top and bottom with french polish labour work NO 1.00

hardware etc. as per site in charge instruction and as per drawing.

Providing & Fixing Librarian table with 18mm thick commercial plywood (Brand

Saras,Kitply,Uniply, Anchor, Green,Wood Stock or century) )with 1.0mm thick lamination sheet

table top supported on 2" x 2" teakwood leg & make 3 nos. drawers of 1' 3" width on both side

116 with necessary french polish hardware labour etc. as per site incharge instruction and as per NO 1.00

drawing ( Size 4' x 2'-6" x 2'-6", all framing other then legs are teak wood of size 2" x 1")

Providing & Fixing simple 12mm thick commercial plywood (Brand Saras,Kitply,Uniply, Anchor,

Green,Wood Stock or century) Rack of size 6' x4' and depth 1'-6" 5 Nos. horizontal partition,

supported 2" x 1" framing with necessary french polish hardware labour etc. as per site

incharge instruction and as per drawing.

Providing & Fixing fitting commercial 8mm thick plywood (Brand Saras,Kitply,Uniply, Anchor,

Green,Wood Stock or century) magazine stand of Size 6' x 4' with 3" x 11/2" vertical

supporting and adjustable lag support and horizontal simple 2" x 1" teakwood patti for

magazine support with necessary french polish hardware labour etc.as per site in charges

instruction and as per drawing.

Providing, supplying & placing precast RCC Woodeny benches as per given specifications.

(Seating plank dimensions : Seating Length of the Bench : 1380 mm, Seating width of the Bench :

119 450 mm, Seating height of the Bench : 450 mm, Seating plank thickness : 60 mm, Total height of NO 1.00

M-30 grade of Concrete using vibration compaction process. Benches consists of 2 Nos.

L-shape base support in wooden texture and 1 Nos. flate back and 1 Nos. bottom plank leg

thickness :90 mm, Leg hight : 830 mm, Leg width : 600 mm, backside plank width : 350 mm,

backside plank length :

mm, backside plank thickness : 60 mm.

Bench top and back planks are treated with special anticorrosive, water proof

coating, prevent sun, rain, light and fungal attack, as to make surfaces glossy and water proof.

The back rest should show as details given by SMC in embossed at casting

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing, polishing and making curvature (wherever

required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c

fixing the railing with necessary accessories & stainless steel dash fasteners , stainless

steel bolts etc., of required size, on the top of the floor or the side of waist slab with

suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight

of stainless steel members shall be considered excluding fixing accessories such as nuts,

bolts, fasteners etc.).

Providing & fixing Z - clamps at all floor levels of approved design to C.I. S.C.I. or PVC pipes

121 including the cost of cutting holes & making good the wall etc.

Complete - 100 mm dia as per architect instructions.

(C) 110 mm dia to upto 150 mm dia No. 20.00 90.00

(C) 150 mm to 200 mm dia No. 20.00 98.00

Providing and constructing sandwitch type Polish Kota Stone cooking platform 0.6 mt.

wide & 0.75 mt. height, including one end side Polish Kota stone (Double Polish) of 1.25 mt.

height & front Polish Kota stone patti of 10 cm wide, vertical partitions of half B.M. wall in C.M.

1:4 and 10mm th. plaster in 1:3 with finishing smooth with cement slurry as required and

122 Stainless Steel sink of 0.45 mt x 0.45 mt size of approved quality and make with required all Rmt. 5.00

fitings & fixitures etc. comp as per instruction given by site in charge at all floors.

Providing and constructing sandwitch type Granite stone cooking platform

0.6 mt. wide & 0.75 mt. height, including one end side granite stone (Double Polish) of 1.25 mt.

height & front granite stone patti of 10 cm wide, vertical partitions of half B.M. wall in

123 C.M. 1:4 and 10mm th. plaster in 1:3 with finishing smooth with cement slurry as Rmt. 5.00

required and Stainless Steel sink of

0.45 mt x 0.45 mt size of approved quality and make with required all fitings &

fixitures etc. comp as per instruction given by site in charge at all floors. (Basic rate of

Granite Rs.1,200.00 / S.M.)

Providing and fixing 150 mm wide, approved quality chicken wire mesh (FRP / PVC)at junction

of brick work and RCC work or two dissimilar surfaces, at all heights fixed by nails, rowal plugs

124 or tag by cement mortar 1:3 before applying the plaster, including curing, scaffolding all S.M. 10.00

complete as directed.

125 Providing and filling Epoxy grout of approved or suggested brand by consultant / Rmt. 40.00 40.00

Engineer in charge in 4mm to 6mm thick tiles joint including spacer with cleaning of joint

by vacuum or blower etc

Providing and fixing rebar of following diameter using chemical grout of

Swanchore/Hilti/Fischer or equivalent make including cost of all equipments, tools, material,

labour, etc. Standard procedure as mentioned in manufacturer's specifications shall

be strictly followed, which shall be submitted and got approved from the authority prior to

start of work. The rate shall also include cost of drilling of hole of required diameter and

depth as mentioned in manufacturer's specification, cleaning the hole with required air blower

126 and other necessary tools and tackles, positioning, providing and grouting chemical, allied

fixtures and fasteners, etc. but excluding the cost of reinforcing bar etc. complete. Item

includes necessary scaffolding, staging, labour, tools and equipments, etc. complete as

directed by the engineer-in- charge.

Carring out plinth treatment to post construction / existing structure by spraying chemical

solution for termite control treatment including labour and material consistment with ISI

specification. Using Chlordene and Chiorpurfiles

20 EC. As per 6131_paret-II Consentration Weight one percent is recommended i.e.

one litre 20 EC chemical emulsion with 19 liter give 1% concrentration inclusive of one

litre chemical emulsion appication at the rate of 5 litre chemical / Sqm of surface is

recommended as per IS.

Providing and fixing rolling shutters of approved make made of 80 mm wide

M.S. laths inter locked together through their entire lenght and jointed together at the ends by

end locks mounted on specially designed pipe shaft with bracket plates, guide channels

128 and arrangements for inside and outside locking with push-pull operation including the cost Smt. 10.00

of hood cover and spring etc. complete (A) Shutters having width below 3.5 M.

Providing and fixing rolling shutters of approved make made of 80 mm wide

M.S. laths inter locked together through their entire lenght and jointed together at the ends by

end locks mounted on specially designed pipe shaft with bracket plates, guide channels

129 and arrangements for inside and outside locking with push-pull operation including the cost Smt. 10.00

of hood cover and spring etc. complete. (B) Shutters having width 3.5 M and above

Providing & Fixing 3 mm thick metal sheet with CNC cutting to fix it on vertical

surface.Steel work welded in built up sections, framed work including cutting, hoisting, fixing in

position and applying a priming coat of red lead paint in beams & joists channels angles, tees,

flats with connection plates or angle cleats as in main & cross beams, hip & trussed purlins

connected to common

raffers & the like.

Providing and laying broken china mosaic flooring for terrace using 12mm to 20mm broken

pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered

131 to bring mortar creme out upto surface using white cement including rounding off junctions Sqm. 10.00

and extending them upto 15 cm along the wall clearing with water and oxalic acid etc. as

132 Providing and Fixing Hollow steel Sections Framed Work including Cutting, Hoisting, Kg 10.00 126.00

Welding & Fixing in position Purlin, Main Chord etc. as per Engineer- in-charge.TATA / JINDAL /

133 Providing cement vata (10 cm x 10 cm size) quarter round in cement mortar Rmt. 10.00 24.28

1:1 including neat cement finishing, watering etc. complete.

Piping for Fire Safety Works

Providing & Laying 'C' Class Heavy G.I. pipe laying. Supply, fabrication, installation, hydro

testing & painting of above ground pipe. with necessary pipe fitments (Flanges, Bands,

Socket etc.) Vertically every 3 mt. & Horizontaly every 2.5 mt. painted with one coat of

primer (Zinc Oxide) & two coats of finshing paints

134 GI support / Clamps / Hangers etc. Hardware (Gaskets, Nut-Bolts, Paint etc.)

Consumables (Welding Rod etc.) and labour charge. Quality : GI, C-Class (Heavy).

Make - Jindal / Asian

d 80mm Dia Rmt. 10.00 1,145.23

e 50mm Dia Rmt. 10.00 726.95

f 40mm Dia Rmt. 10.00 536.55

g 25mm Dia Rmt. 10.00 356.71

Fire extinguisher - ABC powder type 6 Kg.

Supply, installation and testing of ABC powder fire extinguisher necessary hardware and

135 Stored pressure mechanism. No. 10.00

Charged with MAP-50% (ABC) Dry powder. with wall mounting clamp.

UOM - Price per each No. Make - Kanex / Safex / Secure Zone

Fire extinguisher - CO2 Gas type 4.5 kg.

Supply, installation and testing of CO2 Gas fire extinguisher with necessary hardware and

136 consumables. No. 10.00

Standard - Confirming to IS:15683-2006 with ISI mark.

UOM - Price per each No. Make - Kanex / Safex / Secure Zone

137 Supplying FIRE bucket round bottom of 9 ltr. capacity made out of 24 gauge No. 10.00 350.00

G.I. sheet with extra handle at bottom duly painted white inside and Red out side with FIRE

mark, filled with dry-sand and kept on existing stand provided or hung on wall hook.

Supplying and erecting floor mounting stand for keeping four nos. of FIRE buckets

comprising 1500mm in lenght, 900mm height frame made out of 30mm x 30mm x 4mm

138 angle from with cross supports for legs, welded with 4 hooks and duly painted with one coat of No. 10.00

red lead and two coats of approved enamelled silver paint.

Hoarding Printing and Mounting

139 Hoarding Printing and Mounting Sft. 12.00 16.50

140 Flex Banner (Any size 240 gsm) Sft. 12.00 8.50

141 Flex Banner with MS (Mild Steel) framing (Any size 240 gsm (Pipe size 25 x Sft. 12.00 53.10

142 Cloth Banner (Upto 8 x 4 feet 140 gsm) Sft. 12.00 23.60

143 Cloth Banner with MS (Mild Steel) framing (Up to 8 x 4 feet 140 gsm) (Pipe Sft. 12.00 65.00

size 25 x 25 x 1.5 mm)

144 Cloth Banner with Wooden stick at both end for rally display (Any size 140 Sft. 12.00 32.85

145 Cloth banner standee (Any size 140 gsm Pipe size 25 x 25 x 1.5 mm) Sft. 70.00 69.50

146 Wall Vinyl Sticker Sft. 28.00 28.00

147 Eco Solvent Vinyl Sticker (120 gsm) with Lamination (100 gsm) Sft. 38.00 38.00

148 Solvent Vinyl Sticker (120 gsm) with Lamination (100 gsm) Sft. 22.00 22.00

149 5mm PVC sheet Eco Vinyl (Any size) Sft. 55.46 55.46

150 Decorative theme base designing & painting with all waterproof materials Sft. 63.00 63.00

SN I T E M Unit QTY SOR 24-25 TOTAL

Without GST & With

White Washing with lime on wall surface to give an even shade & surface incl. throughly brooming the surface to

1 remove dirt, dust mortar drops & losse scales of lime wash &

other foreign matter Two coats.

(B) Ceiling S.M. 100.00 14.21

---do Extra Subsequant coat over above Item

(A) walls S.M. 100.00 6.01

(B) Ceiling S.M. 100.00 6.51

Colour washing with lime on wall over & incl. a primary coat of white washing to give an even shade & surface incl.

2 throughly brooming the surface to remove all dirt, dust mortar

drops & loose scales of lime wash & other foreign matter.Two coats.

(B) Ceiling S.M. 100.00 15.37

---do Extra Subsequant coat over above Item

(A) walls S.M. 100.00 8.35

(B) Ceiling S.M. 100.00 10.53

Distempering two coats with oil bound washable distemper of approved brand & manufacture & of

required shade on wall surface to give an even shade over and & including a priming coat of alkali resistance

3 primer of approved brand after throughly brushing the surface to give an even shade after throughly brushing the

surface free from mortar droppings and other foreign matter and also including preparing the surface even

(B) Ceiling S.M. 100.00 84.37

---do Extra Subsequant coat over above Item

(B) Ceiling S.M. 100.00 35.25

Apply two coats of putty and two coats of primer of approved brand and manufacture on new wall surface to give 100.00 40.59

4 an even shade including thoroughly brushing the surface free S.M.

from mortar dropping and other matter and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on S.M. 100.00

5 undecorated wall surface to give an even shade including throughly brushing the surface free from mortar

droppings and other foreign matter and sand

papered smooth.

For every subsequent coat Extra over item no.above S.M. 100.00 35.41

6 Distempering two coats on previously distempering wall (without primer) with oil bound washable S.M. 100.00

distemper of approved brand & required shade on wall surface to give an even shade after throughly brushing the

surfaces clean of all grease, dirt loose places

of sceles & also including preparing the surface even and smooth.

7 Applying Priming coat over new steel and other metal surface after over and including preparing the surface by S.M. 100.00

throughly cleaning oil, grease dirt and other foreign matter and scoured with brushed fine steel wool, scrapers and

sand paper with ready mixed priming

paint brushing red lead.

Painting two coat (excluding priming coat) on new steel and other metal surface 100.00 68.57

8 with synthetic enemal paint, burshing to give an even shade including cleaning the surface of all dirt, dust and S.M.

other foreign matters.

9 Painting one coat (excluding priming coat) on Previously Painted steel and other 100.00 39.93

metal surface with synthetic enemal paint, burshing to give an even shade including cleaning the surface of S.M.

all dirt, dust and other foreign matters.

For every subsequent coat Extra over item no.above S.M. 100.00 40.09

Applying Priming coat over new wood & wood surface after & incl. preparing the surface by throughly 100.00 43.10

10 cleaning oil grease dirt & other foreign matter sand papering & S.M.

knetting Really mixed paint brushing priming for enamel.

Painting two coats (excluding priming coat) on New wood & wood based surface 100.00 92.87

11 with enamel paint to give an even shade & surface incl. cleaning of all dirt, dust & other foreign matter. S.M.

Painting two coats (excluding priming coat) on previously painted wood & wood 100.00 47.44

12 based surface with enamel paint to give an even shade & surface incl. cleaning of all dirt, dust & other foreign S.M.

Polishing with french polished on New wood & wood based surface to give an even surface incl. cleaning the 100.00 142.49

13 surface of all dirt, dust & sand papered smooth incl. a cost of S.M.

Polishing with french polished on previously polishing wood & wood based surface to give an even surface incl. 100.00 73.34

14 cleaning the surface of all dirt, dust & sand papered smooth S.M.

incl. a cost of wood filler.

Painting two coats of enamel paint over priming coat (including priming coat) on 100.00 90.00

15 wall after removing entire surface dirt, dust foreign matter & also incl. preparing the surface even & sand S.M.

papered smooth etc. comp.(M.R.)

Painting two coats of enamel paint (Excluding priming coat) over previously painted 1000.00 60.00

16 wall after removing entire surface with even shade & surface after removing dirt, dust foreign matter etc. S.M.

Providing & applying two coats of weather shield max paint (3 coats may be required in case of darker 100.00

colours.)of ICI Dulux or Apex Ultima of Asian Paint including applying exterior acrylic primer coat as per

manufacturers specification and directions in shade and colour approved by architects, on exterior

surfaces of the building including scaffolding, preparing the surface, watering, curing etc. complete and as

directed by the architects and manufacturers.

Surface Preparation :

surface is thoroughly clean, dry and free from all loose dirt, chalk, grease, fungi, algae and flaking paint. This can be

achieved by brushing with a wire/ stiff coir brush, followed by water jetting if required. Fill up all minor cracks

and defects with white cement and sand mixture in the ratio 1:3. For application on previously painted wall,

previous coatings of paint must be thoroughly scraped off and Clean the surface thoroughly using wire

Apply a liberal coat of exterior acrylic primer and allow it to dry for 4-5 hours. Application of putty is not

Minimum 4-6 hours duration is required between each coat of weather shield max paint

Aluminium works

SN Description Unit QTY SOR 24-25 TOTAL

Providing and fixing window having extruded aluminum Colour anodized section frame main outer size 127mm x

38.10mm x 1.35mm @wt. 1.384kg/m, horizontal Four track member size 122.20mm x 31.75mm x 1.10mm@ wt

1.205 kg/m, vertical member of size 122.20mm x 31.75mm x 1.50mm @1.398 kg/mt with sliding

shutters of horizontal member size 40mm x 18mm x 1.29mm@ 0.456kg/mt ,vertical member of size 40mm x

18mm x 1.29mm @ 0.456 kg/mt with 5 mm thick transparent bronze colour tinted float glass with powder coated

aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for

(A) Same as above but Colour anodized S.M. 5.00 2,140.33

Providing and fixing window having extruded aluminium Powder Coated section frame main outer size 95 mm x

24 mm x 1.17 mm (of jindal section no:2459 @ Wt. of 0.738 Kg/mt), horizontal Three track member size 92 mm x

31.75 mm x 1.30 mm (of jindal section no;8688, @ Wt. 1.07 Kg/mt), vertical member of size 92 mm x

1.50 mm (of jindal section no:8933, @ Wt. 1.06 Kg/mt) with sliding shutters of horizontal member size

2 mm x 18 mm x 1.29 mm (of jindal section no:8947 @ wt. of 0.456 kg/mt), vertical member of size 40 mm x 18 S.M. 5.00

mm x 1.29 mm (of jindal section no:8949 @ wt. of 0.456 kg/mt) with 5 mm thick transparent bronze colour

tinted float glass with powder coated aluminium fittings & fixtures and transparent silicon sealant glass fixing to

frame as per details etc.

(A) Same as above but Colour anodized S.M. 5.00 1,591.87

Providing and fixing window having extruded aluminium Powder Coated section frame main outer size 63.50 x

38.10 x1.95 mm (of Jindal section no.4605, @ Wt. 1.094Kg/mt) horizontal Two track member size

mm x 31.75 mm x 1.20 mm (of jindal section no:8687, @ Wt. 0.695 Kg/mt.) vertical member of size 61.85 mm x

31.75 mm x 130 mm (of jindal section no:8758 @ wt. of 0.659 kg/mt) with sliding shutters of horizontal member

size 40 mm x18 mm x 1.29 mm ( of jindal section no:8949, @ Wt. of .456 Kg/mt) vertical member of size 40 mm x

3 18 mm x 1.29 mm (of jindal section no:8947, @ Wt. of 0.456 Kg/mt/section 8948, @ Wt. of 0.457 Kg/mt) with 5 mm S.M. 5.00

thick tranparent bronze colour tineted float glass with powder coated aluminium fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details etc. complete for window.

(A) Same as above but Colour anodized S.M. 5.00 1,705.67

Providing and fixing standared extruded ofalluminium section of size 63mm x 38.10mm x1.2mm , @ Wt. 0.643

Kg/mt with colour Powder

4 Coated alluminium frame for ventilation with 5 S.M. 5.00

mm thick frosted glass as details etc complete for Ventilation

(A) Same as above but Colour anodized S.M. 5.00 1,175.56

5 Providing and fixing standared extruded of aluminium section of size 61 x 37.0 x0.90 mm (of Jindal section S.M. 5.00 1,833.29

no.14080, @ Wt. 0.471 Kg per mt) with Powder Coated alluminium frame with 5 mm thick transparent

bronze colour tinted float glass as details

etc. complete for fix window.

(A) Same as above but Colour anodized S.M. 5.00 1,833.29

Providing & fixing partly panel & partly glass Powder Coated Aluminium doors with aluminium section of

Hindalco, Jindal , Narmada,Banco or Equivalent approved make having Poder Coated outer frame Leg Partition

section of 63.50 mm x 38.10 mm having weight 1.158 kg. / R.M. shutter section having size 83.5 mm x 44.45mm

( top & bottom: 1.384 kg./rmt. and middle 1.139 kg./rmt.) door vertical 47.62mm x 44.45 mm ( vertical:0.881

kg./rmt. & top hing side:0.974 kg./mt.), Glazing Clip (Jindal Section No. 19370 Wt. 0.109 Kg./ Mt.) with 5mm thick

sheet glass in acid frogting and 12 mm thick prelaminated sheet of Greenlam, Panama or archid make as approved

by Engineer-in- charge including fixing brass pivot, handle, lock etc. complete.

(A) Same as above but Colour anodized S.M. 5.00 3,237.00

Providing & fixing Powder Coated Aluminium partly glazed and partly panelled partition using medium

duty sections of Hindalco,Zindal, Narmada, Banco or Equivalent approved make having section 63.50 mm x

38.10mm ( Frame-.758 kg/rmt & Middle section- 0.819 Kg./rmt), Galzing Clip with 5 mm thick clear float

glass of approved make including all other necessary fittings and fixtures. Entire work will have to be made water

7 proof using necessary rubber sectioned wherever required. Gaps all round the frame to be filled with approved S.M. 10.00

water proof sealent. Bottom portion of doors both side to be covered with 12mm thick prelaminated particle

board of approved

make and quality and as per design.

(A) Same as above but Colour anodized S.M. 5.00 2,400.00

ITEMS FOR GROUND DEVELOPMENT WORK

SN Item Unit QTY SOR 24-25 TOTAL

Box Cutting the road surface to proper slope and camber for making base

1 includinng removing the excavated stuff and depositing on the road side slope as directed up to C.M. 10.00

2 Preparation of subgrade with Compacting, Levelling and consolidation of subgrade with S.M. 5.00 9.00

miniroller /plate vibrator machine including watering and filling in depressions which occur

during the process as directed by engineer in

3 Providing & filling with Mix soil in layers of 20 cm. Th'. Incl. watering, C.M. 20.00 225.00

ramming & consolidation etc. complete.

4 Supplying & filling fine sand(pana) in 75 mm / 100 mm / 150 mm compacted thickness over C.M. 5.00 1,016.00

the base including necessary compaction, watering etc. complete. Item includes leveling by

using vibratory plates compacted

machine and as directed by engineer in charge.

5 Providing and laying cement concrete 1:5:10 (1- Cement : 5- Coarse sand : 10- hand broken C.M. 5.00 2,606.92

stone aggregates 40 mm nominal size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

Providing 100mm thick readymade C.C. kerb of strength M-20 (size 300mm x 380mm)

purchased from SMC's approved paverblock manufacturer & setting in line, level and in truly

vertical position, including filling joints in C.M. 1:1 (1 part of cement : 1 part of stone dust)

smooth pointing in C.M. 1:1 (1 part of cement : 1 part of coarse sand) including watering etc.

as directed by engineer in charge.

For rounding at the edge of footpath (For fanning portion) R.M. 10.00 274.00

Providing interlocking type Rubber moulded cement concrete paver block of approved

shape, design & colour having 60mm thickness (M-35) purchased from SMC's approved

paverblock manufacturer only & fixing of fine sand bedding. Item includes levelling by using

7 vibratory plates compacted machine. Item also includes all materials, labour, equipments, tools, S.M. 10.00

plants, watering, cleaning etc. complete.

Without colour S.M. 10.00 524.00

Providing & fixing interlocking type Cement Concrete paver block of approved shape & design

having 60 mm thickness (M-40) purchased from SMC's approved paverblock manufacturer

8 only on fine sand bedding. Item includes leveling by using vibratory plates compacted machine. 10.00

Item also includes all materials, Labour, euipments, tools, plants, watering, cleaning

For Road Junction 80 mm thick ( M-50) S.M. 10 714

Providing & laying Granular sub base (GSB)confirming to Grading-V of Table 400.0 of

compacted thick of 150mm with specified graded stone metal and sand mixed in place and

laid with mechanical means spreading with motor grader and compacting with vibratory

9 roller having minimum 80-100 KN static weight to acheve desired density of 98% of MDD C.M. 5.00

including all material, labour, machinery with all leads and lift etc. complete.

10 Providing & laying cement concrete Pavement using 1:1.5:3 (1 cement:1.5 sand:3 graded C.M. 5.00 5,981.00

stone agg. 20 mm nominal size) & Vaccuum Dewatering technique including floating surface

with a skim powder floater, curing etc.

11 Providing & laying cement concrete Pavement using 1:2:4 (1 cement:2 sand:4 graded stone C.M. 5.00 5,245.25

agg. 20 mm nominal size) & Vaccuum Dewatering technique including floating surface with a

skim powder floater, curing etc.

12 Providing and laying 200 micron plastic sheet on prepared sub base For S.M. 26.00 26.00

13 Cutting of Groove 5 to 7 mm thick in VDS for depth 1/3 of total thickness with R.M. 50.00 50.00

filling of epoxy sealent as directed by engineer in charge

S.N. ITEM UNIT QTY RATE for 24-25 TOTAL

1 Providing & fixing C.P. brass pillar cock with copper connection, C.P.

brass screws complete

Make- Cera F2013101, HindWare Cat. No.: F650003, Jaquar FLR- NO. 25.00 1457.97

2 Providing & Fixing 15 mm Dia bib tap with wall Flange at all floor

levels, polished bright etc. comp.

Make- Cera F2013151 BIB COCK, HindWare F280002 BIB COCK, NO. 20.00 1353.77

Jaquar FLR-5047 N BIB COCK

3 Providing & Fixing 15 mm Dia 2 way bib tap with wall Flange at all

floor levels, polished bright etc. comp.

Make- Cera F2013163, HindWare Cat. No.: F530004, Jaquar FLR- NO. 20.00 1828.81

4 Providing flush cock consisting lever, cartridge sleeve & flange &

Make- Cera EXPOSED PART F2013751 &Concealed part F4060101 , Jaquar FLR 5083 NO. 20.00 2056.47

KN , CONCEALED BODY ALD-081,HINDWARE F730013 & CONCEALED STOP COCK

5 Providing & fixing 15mm C.P. brass angle valve (Stop Cock) with

C.P. copper connecting pipe 450 mm long and nuts, washer and brass flange

complete, including cutting and making good the wall where required.

Make- Cera F1020362, HindWare Cat. No.: F440020 F850094, NO. 20.00 1564.36

jaquar CON 053 KN

Providing and fixing Wash Down Water closet European type W.C. pan with integral

P or S trap with normal closing seat cover L bend ncluding jointing the trap with soil

6 pipe in cement mortar 1:1 (1 cement

: 1 find sand) (A) Viterous china pattern - I

Make- Cera CONVENTIONAL B1510121 , HindWare sleek 20011, NO. 20.00 3530.09

Jaquar- CNS-WHT-751P180SPPZ

7 Providing & fixing Wash Hung basin with single hole for pillar tap , Size- 550 x 400

mm at all floor levels, with C.I. or M.S. Brackets painted white incl. cutting holes &

making good the same etc.

complete. For all Floor

Make- Cera Cat. No. S2040121, Jaquar SLS- WHT -6801 NO. 20.00 3276.63

Providing & fixing white vitreous china urinal of size 450 x325mm as per IS-2556

(Part-2 ) with C.I. hangers and 15mm dia. C.P. spreader,32mm dia CP bottle trap and

8 pipe to wall with C.P. flange complete including cutting and making good the walls

wherever required.

Make- CeraCat. No. S4020103, Jaquar URS-WHT-13261H ,HindWare NO. 20.00 2535.70

Providing & fixing of overhead shower 80 mm (3”) dia with 3 flow with Overhead

9 Shower arm 200 mm with wall flange complete

Make- Cera F7010602AB, Jaquar OHS-1989 ,HindWare Cat. No.: NO. 20.00 1526.42

10 Providing and fixing Towel Ring fabricated from seamless stainless steel tube 2mm

thick in bath room with polished wall flange at end of bars with heavy duty anchor

fasteners & accessories.

Make- Cera F5014115CH, Jaqua ACN-1121N ,HindWare F880007 NO. 20.00 924.24

Providing & fixing S.S.towel rail of 600 mm long approved make including,

11 providing & fixing C.P. brass screws, making holes in walls

Make- Cera F5015103CH,Jaquar 1111BSM ,HindWare F880005T NO. 20.00 1100.42

Providing & Fixing stainless steel recessed type Soap dish of

12 approved make. Including providing & fixing screws, washers, cutting & making

good the walls.

Make- Cera F5007106, Jaquar ACN-1131N ,HindWare F880011 NO. 20.00 839.91

Prov.& Fixing water closet squatting pan (Orissa type W.C.pan) at all floor levels,

size 500mm x 400 mm incl. 100 mm size "P'or "S" trap for water closet squatting pan

13 joining the trap with the pan & soil pipe in

C.M. 1:1 (1cement :1 fine sand) etc. Comp.(A) Vitreous china long

Make- Cera S3010109, Jaquar ,HindWare 20143 NO. 20.00 3277.39

14 Prov.& Fixing Health Faucet ABS Body with wall Hook and 1 Meter

chrome plated PVC Hose Pipe.

Make- Cera F8030106AB, Jaquar ALD-587 ,HindWare F160109 NO. 20.00 1009.90

15 Providing & fixing white vitreous china Ladies urinal of size 470 x360X100 mm and

15mm dia. C.P. spreader, and pipe to wall complete including cutting and making

good the walls and floors

wherever required.

Make- Cera 4040101 ,HindWare 60003 NO. 20.00 2316.05

Providing & fixing Paper holder with flap guard of 150 mm long

16 approved make including, fixing C.P. brass screws, making holes in walls & making

Make- Cera f5002110, Jaquar AHS-1551 ,HindWare F890003 NO. 20.00 1751.51

17 Providing & Fixing pressmatic bib tap with wall Flange at all floor

levels, polished bright etc. comp.

Make- Cera F9020151, Jaquar PRS-043 ,HindWare F310016 NO. 20.00 1842.06

18 Providing Metropole Flush Valve Dual Flow 40mm

Size (Concealed Body)

Make- Cera F8010202 , Jaquar FLV-1089NSQ ,HindWare F860075 NO. 20.00 3500.99

19 Providing Sink Cock with Regular Swinging Spout

Make- Cera F2008251, Jaquar FLR-5347N ,HindWare F650013 NO. 18.00 1785.90

Rehabilitation Work Items

'Fixing clerestory window chowkhats in existing openings including cutting

masonry for hold fasts, embedding hold fasts in cement concrete blocks with

cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate

1 mm single size), painting two coats of coal tar to sides of chowkhats and making 1.00

good the damge to walls complete including disposal of rubbish to the dumping

Providing and applying cement mortar (1:3) modified by using polymer and

expanding grout additives at 25mm thickness for repair/strengthening of various

RCC elements at all floor levels, lead, lift, including breaking, chipping, dismentling

existing cover concrete and exposing existing reinforcement, applying wirebrush

for making surfaces of steel and concrete free from rust and other loose materials,

applying rust removing chemical on existing reinforcement, applying anti-

2 corrosive coating on existing reinforcement, applying polymer bonding agent on Sq.mt 1.00

existing concrete surfaces before applying polymer modified mortar in specified

thickness as directed by the Engineer-in-charge.

Providing and applying cement mortar (1:3) modified by using polymer and

expanding grout additives at 50mm thickness for repair/strengthening of various

RCC elements at all floor levels, lead, lift, including breaking, chipping, dismentling

existing cover concrete and exposing existing reinforcement, applying wirebrush

for making surfaces of steel and concrete free from rust and other loose materials,

applying rust removing chemical on existing reinforcement, applying anti-

3 corrosive coating on existing reinforcement, applying polymer bonding agent on Sq.mt 1.00

existing concrete surfaces before applying polymer modified mortar in specified

thickness as directed by the Engineer-in-charge.

Providing Cement Concrete work 50% - M30-(design mix) and 50% micro concrete

plus recron - 3s (12mm long polyester fiber) plus appropriate dose of super

plasticizer with curing, finishing smooth, etc. complete for jacketing of structural

members at all floor levels, lead, lift, including breaking, chipping, dismentling

existing loose cover concrete and exposing respective existing reinforcement as

directed by the engineer-in-charge, applying wirebrush for making surfaces of steel

and concrete free from rust and other loose materials, applying rust removing

chemical on existing reinforcement, applying anti-corrosive coating on existing

reinforcement, applying polymer treatment and bonding agent on existing

concrete surfaces as directed by the Engineer-in-charge, etc. complete. The make

4 and quality of rust removing chemical, anti-corrossive coating, polymer / epoxy C.M. 1.00

bonding agent shall be approved by engineer-in- charge. The procedure for

application shall be strictly in accordance with manufacturer's detail specification,

which shall be submitted before start of work and shall be approved by the

Engineer-in-charge.

Providing Cement Concrete work 75% - M30-(design mix) and 25% micro concrete

plus recron - 3s (12mm long polyester fiber) plus appropriate dose of super

plasticizer with curing, finishing smooth, etc. complete for jacketing of structural

members at all floor levels, lead, lift, including breaking, chipping, dismentling

existing loose cover concrete and exposing respective existing reinforcement as

directed by the engineer-in-charge, applying wirebrush for making surfaces of steel

and concrete free from rust and other loose materials, applying rust removing

chemical on existing reinforcement, applying anti-corrosive coating on existing

reinforcement, applying polymer treatment and bonding agent on existing

concrete surfaces as directed by the Engineer-in-charge, etc. complete. The make

5 and quality of rust removing chemical, anti-corrossive coating, polymer / epoxy C.M. 1.00

bonding agent shall be approved by engineer-in- charge. The procedure for

application shall be strictly in accordance with manufacturer's detail specification,

which shall be submitted before start of work and shall be approved by the

Engineer-in-charge

Providing and appliying thixotropic Making up lost section of concrete / mortor 1

with thixotropic repair mortor of one- component, normal-setting, shrinkage-

compensating, thixotropic mortar for layers up to 25 mm thick. Supply and

application of one-component, normal-setting, shrinkage- compensating

thixotropic mortar made from cementitious binders, selected aggregates, special

additives and synthetic polyacrylonitrile fibres, for reconstructing deteriorated

concrete structures. Apply the mortar after adequate preparation of the substrate

by removing all deteriorated concrete to form a sufficiently-rough, solid substrate

with no detached portions. Clean the steel reinforcement down to bare metal and

apply a passivating treatment by brush- applying two coats of one-component, anti-

corrosion cementitious mortar. Apply the product by trowel or spray with a

continuous-feed rendering machine on a clean substrate saturated with water in

6 layers up to 20 mm thick.

To improve expansion in the open air during the first few days of curing, add a

special curing additive when mixing the mortar to reduce both plastic and

hydraulic shrinkage at a dose of 0.25% in weight on the weight of the mortar. The

product must comply with the minimum requirements of EN 1504-3 for structural

mortars and have the following performance characteristics:

Compressive strength (EN 12190) (MPa):> 40 (after 28 days) Flexural strength

(EN 196/1) (MPa): 7 (after 28 days) Compressive modulus of elasticity (EN 13412)

(GPa): 25 (after 28 days)

Adhesion to substrate (EN 1542) (MPa):> 2 (after 28 days) Capillary absorption

(EN 13057) (kg/m²•h0.5): < 0.20 Thermal compatibility measured as adhesion

according to EN 1542 (MPa): – freeze-thaw cycles with de-icing salts (EN

13687/1): > 1.5 (after 50 cycles)

Storm cycles (EN 13687/2):> 1.5 (after 30 cycles)

– dry thermal cycles (EN 13687/4):> 1.5 (after 30 cycles) Reaction to fire (EN

13501-1) (Euroclass):1

Consumption (per cm of thickness) (kg/m²): approximately

included and calculated in the price for work carried out according to specification:

(1) hydro-cleaning of adhesion surfaces and saturation of substrate with water Sq.mt 1.00

immediately before applying the mortar;

(2) application of the mortar by trowel or spray around steel reinforcement;

(3) levelling off surfaces with a straight edge and final tamping;

(4) careful curing of the mortar by spraying on water for at least 7 days (3times)

after application.

Providing and appliying thixotropic Making up lost section of concrete / mortor 1

with thixotropic repair mortor of one- component, normal-setting, shrinkage-

compensating, thixotropic mortar for layers up to 50 mm thick. Supply and

application of one-component, normal-setting, shrinkage- compensating

thixotropic mortar made from cementitious binders, selected aggregates, special

additives and synthetic polyacrylonitrile fibres, for reconstructing deteriorated

concrete structures. Apply the mortar after adequate preparation of the substrate

by removing all deteriorated concrete to form a sufficiently-rough, solid substrate

with no detached portions. Clean the steel reinforcement down to bare metal and

apply a passivating treatment by brush- applying two coats of one-component, anti-

corrosion cementitious mortar. Apply the product by trowel or spray with a

continuous-feed rendering machine on a clean substrate saturated with water in

7 layers up to 40 mm thick. To improve expansion in the open air during the first few

days of curing, add a special curing additive when mixing the mortar to reduce

both plastic and hydraulic shrinkage at a dose of 0.25% in weight on the weight of

the mortar. The product must comply with the minimum requirements of EN 1504-

3 for structural mortars and have the following performance characteristics:

Compressive strength (EN 12190) (MPa):> 40 (after 28 days) Flexural strength

(EN 196/1) (MPa): 7 (after 28 days) Compressive modulus of elasticity (EN 13412)

(GPa): 25 (after 28 days)

Adhesion to substrate (EN 1542) (MPa):> 2 (after 28 days) Capillary absorption

(EN 13057) (kg/m²•h0.5): < 0.20 Thermal compatibility measured as adhesion

according to EN 1542 (MPa): – freeze-thaw cycles with de-icing salts (EN

13687/1): > 1.5 (after 50 cycles)

Storm cycles (EN 13687/2):> 1.5 (after 30 cycles)

– dry thermal cycles (EN 13687/4):> 1.5 (after 30 cycles) Reaction to fire (EN

13501-1) (Euroclass):1

Consumption (per cm of thickness) (kg/m²): approximately

included and calculated in the price for work carried out according to specification:

(1) hydro-cleaning of adhesion surfaces and saturation of substrate with water Sq.mt 1.00

immediately before applying the mortar;

(2) application of the mortar by trowel or spray around steel reinforcement;

(3) levelling off surfaces with a straight edge and final tamping;

(4) careful curing of the mortar by spraying on water for at least 7 days (3 times)

after application.

8 Pointing on brickwork with cement mortar 1:1 (1-cement : 1- Sq.mt 1.00 199.00

coarse sand) (B) Ruled pointing.

9 Aluminum section Window opening and refixing with all Sq.mt 1.00 481.00

necessary fix & fiting etc maid in wisely.

Providing & Applying 20mm.to 35mm Th.(Max. 35mm thickness consider) Heavy

Roller plaster on walls or similar surfaces at all floor levels consisting of 12 mm av.

Backing coat of C.M. 1:3 (1 cement:3 sand : racron 3s ( 0.5 nos per bag )) also

plaster master wterproofing chemical 100 ml /bags as per companey manual &

10 approved by E.I.C or consultant & 8 mm. th. Finishing coat of C.M. 1:1 (1 cement: 1 Sq.mt 1.00

sand) apply thick cement slurry and apply roller horizontal as well as vartical ( two

times ) up to good quality and size of grain in elevation as per directed by engineer

Providing & fixing G.i mesh 25X25X3mm used for celling repair fixed with celling

11 rebar column as per directed by Sq.mt 1.00

enginner incharge rate excluding the rebar cost .

RCC Core Cutting is about making precise, circular cuts for creating holes of

required diameters for Rehabilitation in civil works. The core drilling rod is fitted

with diamond pieces at the drilling end. The core cutting machine can be used for

both horizontal and vertical hole making purposes.

Apply hacking on RCC member manual or by mechanical as discoused by engineer

incharge. 350 - 400 notches (dents) per sqmt. Process of making the back ground

14 rough before plastering for better bonding of mortar with RCC (Tacha) Sq.mt 1.00

15 Polishing flooring after repair work done as direct by E.I.C Sq.mt 1.00 172.00

16 Providing & Fixing Nylon net (having net weight-0.065 kg/sq.mt) in outside as well Sq.mt 1.00 32.00

as inside plaster / terrace water proofing at any height (no load or lift will be paid

same) etc as direct by E.I.C

Providing & Applying Surface Water Proofing treatment on existing Water

(1) Cleaning Surface Slab up to Mother slab & free from any Loose Material. Paint,

Dust, Greaze or Remove all existing bituminious Coating Completely. It is

recommended to use intense wise brushing on high speed Water jet for through

(2) The Substrate must be checked for its Soundness using Small hammer. All

Cracks at corner joint, Channels and Parapet Should be Properly treated.

(3) Cracks/construction joints treatment: Opening the cracks/construction joints,if

any, in V/U shape using electrically operated cutting machine. Cleaning the surface

thoroughly from dust and loose partical using wire brush and air blower. Filling the

cracks if any with polymer modified cement mortar hybrid PU Sealant depending

on the width of crack/joint.

17 (4) Epoxy primer:The Epoxy primer must be applied on clean and dry surface by Sq.mt 1.00

mixing base and hardner in equal proportions with the help of strirrer and adding

equal amount of water and appling on the surface at 80-100 grams per sqmt and

allowed it to dry untill tack free.

(5) Hybrrid polyurea part-A(base) and part-B(hardner) are packed in two separate

containers having the correct predetermined mixing ratio by weight.Stir individual

container separately,Part-A and PArt-B very well, to get homogeneous

material. The whole quantity of Part-B is added into Part-A.

18 Providing & Applying vata (10 cm x 10 cm size) quarter round in cement mortar R.M. 1 100.00

(1:3) modified by using polymer and expanding grout additives including neat

cement finishing,

watering etc. complete.

Carrying out Injection grouting for cracks in RCC structural members by drilling

holes of 15 mm diameter upto minimum depth of 75 mm, fixing aluminium nozzle

/ rubber pipe using non-shrink epoxy putty, injecting epoxy grout material at

specified pressure with grouting pump till it the material refuses to impregnate

inside the hole. If required or suggested by the Engineer-in-charge, injection

grouting shall be carried out more than once for a hole to assure proper spreading

19 of grout material and filling of capillaries / voids within the element. After

satisfactory injection grouting, the nozzle/pipe shall be cut and sealed by non-

shrink epoxy putty.

The surface shall be finished smooth with C:M (1:4) and reinstated to the original

condition as directed by the Engineer-

The rate shall include the cost of providing and supplying all tools, materials, labour,

scaffolding, props, formwork, etc. complete. The make and quality of epoxy grout,

epoxy putty, etc. shall be approved by the Engineer-in-charge. The procedure for

application shall be strictly in accordance with manufacturer's detail

specification, which shall be submitted before start of work and shall be Sq.mt 1.00

approved by the Engineer-in-charge. (Actual no of holes

and their locations shall be as decided by the Engineer-in-charge)

Carrying out Injection grouting for cracks in RCC structural members by

drilling holes of 15 mm diameter upto minimum depth of 75 mm, fixing aluminium

nozzle / rubber pipe using cementitious compound, injecting polymer modified slurry

(SBR+cement+water) 1:1:1 material at specified pressure with grouting pump till

it the material refuses to impregnate inside the hole. If required or suggested by

the Engineer-in-charge, injection grouting shall be carried out more than once for a

hole to assure proper spreading of grout material and filling of capillaries / voids

within the element. After satisfactory injection grouting, the nozzle/pipe shall be cut

and sealed by non-shrink epoxy putty. The surface shall be finished smooth with

C:M (1:4) and reinstated to the original condition as

directed by the Engineer-in-charge.

The rate shall include the cost of providing and supplying all tools, materials, labour,

scaffolding, props, formwork, etc. complete. The make and quality of epoxy grout,

epoxy putty, etc. shall be approved by the Engineer-in-charge. The procedure for

application shall be strictly in accordance with manufacturer's detail

specification, which shall be submitted before start of work and shall be Sq.mt 1.00

approved by the Engineer-in-charge. (Actual NOS of holes

and their locations shall be as decided by the Engineer-in-charge)

Providing and applying cement mortar 1:4 enriched with expanding grout additive in

required proportion in cement for repair of cracks in RCC and non-RCC members

after making 25mm x 25mm groove, cleaning the surface and applying coat of

bonding, finishing smooth the repaired surfaces, providing and applying curing agent

on the repaired surfaces, etc. complete at all floor levels as directed by engineer-in-

charge. The make and quality of expanding grout additives, bonding agent, curing

21 agent, etc. shall be approved by the engineer-in-charge. The procedure for application Sq.mt 15.37

shall be strictly in accordance with manufacturer's detail specification, which shall be

submitted before start of work and shall be approved by

the Engineer-in-charge.

EXECUTIVE ENGINEER

SOUTHZONE-B(KANAKPUR)

SURAT MUNICIPAL CORPORATION