REPAIRSMAINTS TO ROOF COVERINGCEILINGJOINERY AND MISC B R REPAIRS INCL REPLACEMENT OF PLUMBING ITEMS FITTING FOR ZONEII AT PATTAN UNDER GE 969 EWS

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level). Complete all as specified and directed by Engineer-In-Charge.

Demolition of stone slabe slabs & tiles of any description or thickness in floor, aprons, plinth protection etc laid bedded and pointed in any mortar. Complete all as specified and directed by Engineer-In-Charge.

Dismantling floor hearth wall tile incl cement mortar bedding, removing serviceable tiles to store and rubbish off the premishes. Complete all as specified and directed by Engineer-In-Charge.

Taking down chowkats or frames but with shutters (without taking off shutters from the frame) exc 1.50 sqm but n. exc 4.00 sqm . Complete all as specified and directed by Engineer-In-Charge.

Taking down shutter only exc 1.00 sqm but n.exc 2.00 Sqm each and refix in the same opening. Complete all as specified and directed by Engineer-In-Charge.

Demolition of brick work, PCC block masonary, stone masonary or boulder masonary built in cement mortar. Complete all as specified and directed by Engineer-In-Charge.

Dismantling of plain corrugated steel sheeting any guage thickness including Nainital or Similar pattern roof coverings (at any height). Complete all as specified and directed by Engineer-In-Charge.

Taking down cement plaster or screed bedding layer of any description from concrete slab/terrace surfaces etc including racking out joints hacking for key, scrubbing down with water etc. Complete all as specified and directed by Engineer-In-Charge.

M&L for brick work with sub class 'B' bricks (Old size) straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6. Complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 15 mm thick plastering on brick work or concrete surface in CM (1:6) and rendering is to be finished even and smooth w/o using extra cement. Complete all as specified and directed by Engineer-In-Charge.

M&L for non-skid coloured ceramic tile 7 to 8mm thick (Square/rectangular/in joint less) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over 15 mm thick screed bed in CM (1:4). Complete all as specified and directed by Engineer-In-Charge.

M&L for glazed ceramic tiles in vertical surface 450 x 350 x 7mm thick colour and design (as approved) in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over 15mm thick cement plaster using CM (1:4). Complete all as specified and directed by Engineer-In-Charge.

M&L for vitrified ceramic tiles dark shade 10mm thick (square/rectangular ) polished ,area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm in floors ,in floors and dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM (1:6). Complete all as specified and directed by Engineer-In-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed bed in (1:6) laid and jointed in neat cement slurry mixed with pigment to match the shed of the slab including rubbing and polishing. Complete all as specified and directed by Engineer-In-Charge.

M&L for hardcore of gauge n exc 63 mm, broken stone or boulders, deposited ,spread and levelled in layers n exc 15 cm thick ,watered and rammed to a true surface. Complete all as specified and directed by Engineer-In-Charge.

M&L for 100mm thick PCC type B-2 (1:2:4) using 40mm graded stone aggregate as in flooring finished even and smooth w/o using extra cement. Complete all as specified and directed by Engineer-In-Charge.

M&L for pre-cast cement concrete rubber moulded glossy finished interlocking paver block of 60 mm thick M-35 grade any colour (as approved) and design over sand cushioning complete including with using grey cement and pigment any shape and size confirming to IS-15658-2006. Complete all as specified and directed by Engineer-In-Charge.

M&L for sand filling under floor or in foundation including watering and consolidation. Complete all as specified and directed by Engineer-In-Charge.

M&L for type D2 1:4:8 (40mm graded aggregate ) cement concrete in foundation filling and mass concrete. Complete all as specified and directed by Engineer-In-Charge.

S & F rubber moulded chequered cement concrete endura tiles 30cm x 30cm x 25mm thick,set, jointed and pointed in neat cement slurry in floors over 20 mm thick screed bed in CM (1:6) finshed with coloured cement to match the shed of the slab. Complete all as specified and directed by Engineer-In-Charge.

M&L for PCC 1:2:4 type B-1 using 20 mm graded aggregate as in bed blocks, bed blocks of hold fasts, coping and chamfered angles and throating etc. Complete all as specified and directed by Engineer-In-Charge.

M & L for 75mm thick PCC 1:3:6 type C-2 using 40 mm graded agg as in plinth protection finished even and smooth w/o using extra cement. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair for 4 mm thick veneered decorative plywood grade 1 (with BWR resin) with decorative veeneers of one side fixed with nails to the surface complete in wall. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair for 4 mm thick veneered decorative plywood grade 1 (with BWR resin) with decorative veeneers of one side fixed with nails to the surface complete in ceiling. Complete all as specified and directed by Engineer-In-Charge.

M&L for plain fillets sequare/ rectangular or traingular in section using 2nd class soft wood clean swan secured with nails exc 3 sqcm but n,exc 6 sqcm in section. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair 2nd class hard wood in scantling clean swan timber framed and fixed to the position to replace old and decayed timber. Complete all as specified and directed by Engineer-In-Charge.

S&F plain framed 2nd class HW rail and style 35mm plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, size of rail and stile as per IS :1003. Complete all as specified and directed by Engineer-In-Charge.

S&F aluminium handles, cast type, anodised 125mm long. Complete all as specified and directed by Engineer-In-Charge.

S&F aluminium, anodised barrel tower bolts of extruded section and fixed of size 150 mm long. Complete all as specified and directed by Engineer-In-Charge.

S&F aluminium alloy , anodised sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded section and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy and fixed lenght of bolt 300mm. Complete all as specified and directed by Engineer-In-Charge.

S&F 100mm butt hinges ,extruded aluminium alloy with galvanisad mild steel hinge pin ,anodised and fixed ,type B-21.Complete all as specified and directed by Engineer-In-Charge.

M&L for two coats of synthetic enamel paint on wood and wood base surface of any description not otherwise described, over 10 cm width or girth over a coat of pink primer incl preparation of surfaces. Complete all as specified and directed by Engineer-In-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering / clading to wall, fixed with self tapping screw. Complete all as specified and directed by Engineer-In-Charge.

M&L for galvanised, corrugated mild steel sheeting 0.63 mm thick with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275. fixed with using screw. Complete all as specified and directed by Engineer-In-Charge.

All as per item No. 34 above but except sheeting removing and refixing , fixed in repair.

S & F in repair vitreous china wash basin, white, flat back, size 550x400mm, plug , porcelain stopper and including brackets with waste fittings and connection pipe etc. Complete all as specified and directed by Engineer-In-Charge.

S&F in repairs pillar taps, 15mm dia cast copper alloy fency type, with capstan heads, chromium plated. Screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly nuts screwed for iron pipe & fixed etc. Complete all as specified and directed by Engineer-In-Charge.

Dismantling PVC water tank exc 500 Ltrs and n.exc 1000 Ltrs capacity. Complete all as specified and directed by Engineer-In-Charge.

M&L for rotational moulded polyethyline water storage tank triple layers 1000 Ltrs capacity ( cylinrical vertical with close stop) hosted and fixed in position, all as specified in SSR Part-I. Complete all as specified and directed by Engineer-In-Charge.

M&L for rotational moulded polyethyline water storage tank triple layers 500 Ltrs capacity in repairs ( cylinrical vertical with close stop) hosted and fixed in position, all as specified in SSR Part-I. Complete all as specified and directed by Engineer-In-Charge.

S&F in repairs ball brass valves 20mm dia high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule fixed. Complete all as specified and directed by Engineer-In-Charge.

Taking down steel water tubing 15mm and connection including cleaning for refixing or removal to store. Complete all as specified and directed by Engineer-In-Charge.

S&F tubes medium grade galvanised with all fitting and fixed to wall or laid in trenches 15 mm bore. Complete all as specified and directed by Engineer-In-Charge.

Refixing only tubes medium grade galvanised with all fitting and fixed to wall or laid in trenches 15 mm bore. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair 3-layer PP-R Polypropylene random copolymer) pipes 16mm bore SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair 15 mm bore bib taps, fancy type chromium plated with crutch or butterfly handle screwed down, screwed for iron pope or for brass ferrule and fixed. Complete all as specified and directed by Engineer-In-Charge.

S & F in repair stop valves fancy type chromium plated screwed down high pressureff, with crutch or butterfly handle, screwed both ends for iron pipe or for unions 15 mm bore and fixed. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair 15 mm bore PTMT bib taps screwed down screwed for iron pipe or for brass ferrule and fixed. Complete all as specified and directed by Engineer-In-Charge. Make : Prayag or equivalent.

S & F in repairs grating doom 100 mm dia of PTMT (Minimum weight 25 gms). Complete all as specified and directed by Engineer-In-Charge.

S&F in repair PVC (SWR ) pipes 110mm single socketed ,in any length with rubber ring joints, laid in trenches or in floor. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair PVC (SWR) bends 110mm dia fixed complete. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair PVC flushing cistern, 10 Litres capacity, low level including brackets, inlet and outlet PVC pipe and fittings complete fixed. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair S S sinks 1 mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste fittings. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair vitreous china squatting pan, Orissa pattern, size 580x440 white,with integral foot rests (excluding flushing cistern & flush pipe) including provision of lime concrete bedding and P or S trap in repairs. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern) white or coloured exclduing flushing cistern and flush pipe and seat cover including provision of concrete / white cementing and P or S trap in repairs. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair chromium plated connection pipe fency type 450mm long at size 15mm bore with standard PTMT nut fixed to GI tubbing. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair brass chromium plated tublar towel rail 20mm dia, 60cm long including side brackets complete. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screw and cleats. Complete all as specified and directed by Engineer-In-Charge. Make : Prayag or equivalent.

S&F in repair brass CP Mixer 15 mm dia for mixing Hot and Cold water screwed down for iron pipe and fixed. Complete all as specified and directed by Engineer-In-Charge.

S&F in repair health faucet (CP) with 8 mm dia 1 mtr long flexible tube with wall hook. Complete all as specified and directed by Engineer-In-Charge. [Make : Jaquar cat No ALD 573 or equivalent.]

Refixing only in repair CP Mixer any type15 mm dia screwed down for iron pipe and fixed after removing defects / leakage. Complete all as specified and directed by Engineer-In-Charge.

M&L for lagging to 20 mm dia pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 in repair. Complete all as specified and directed by Engineer-In-Charge.

M/s GHULAM HASSAN MIR

M/s Mushtaq Ahmad Bhat

Javeed And Co

M/S GHULAM HASSAN MALIK

M/S GHULAM RASOOL LONE AND SONS

M/S HAJI MOHD ASHRAF SUMJI