SPECIAL REPAIRS OF BATHROOMS AND TOILETS OF BLDG NO P-65 AC DEPOT, ACC AND S UNDER GE (NORTH) AHILYANAGAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M & L moorum filling in floors or paving laid in layers n.exc. 15 cm thick spread leveled and rammed including watering complete all as specified and directed

M & L hard core of gauge etc. 63 mm but n. exc. 100 mm deposited spread and leveled in layers n. exc. 15cm thick water and rammed etc. complete all as specified and directed.

M&L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed.

M&L for coloured glazed ceramic tiles digitally printed 300x450mm, 7-8 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L for joint free /rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile 400x400mm , as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free anti skid ceramic coloured tiles 300x300mm 7-8mm thick matching to dado tiles area of each tile, as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick Screed bed etc complete all as specified and directed by Engineer-in-Charge

M&L in repairs for Machine cut cudappah stone slab 20-25mm thick over and including 15mm thick cement and sand screed in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified

M&L for old size brickwork with fly ash bricks straight or curved on plan exc 6m mean radius,built in CM 1: 6 complete all as specified

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in 1: 6 complete all as specified

Taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key complete all as directed

M&L for 15 mm thick rendering on wall surface in CM 1:4 in with water proofing compound incl. finishing the surface even and smooth without using extra cement. (WPC shall be measured and paid seperately)

M&L for rendering 10 mm thick on fair faces of brick work or on concrete surfaces in CM 1:6 finished even and fair without using extra cement including sagol finished complete all as specified.

M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparation of old plastered treated surfaces of walls by brooming down and and applying one coat of weather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed.

M & L for preparation of newly plastered surface of wall and apply three coats of white wash any height including scaffolding etc complete all as directed.

M & L for preparation of newly plastered surface of ceiling and apply three coats of white wash any height including scaffolding etc complete all as directed.

M&L for preparation of old plastered or unplastered surfaces of walls including cornices etc by brooming down or steel wire brushing scraping down smook soot, moulds, moss and efflorescent salt, trading oil and greasy spots and applying one coat of white lime wash at any height including scaffolding etc complete all as specified and directed by Engineer-in-charge.

.-dittto- all as per ser item No 23 (here-in-before) but on ceiling.

S&F fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge.

S&F Vitreous China urinal, Half stall type, white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe andwaste pipe)

S&F in repairs 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm bore steel tubing and connections

Ditto all as per ser item No 30 above but 20 mm bore tubing

Ditto all as per ser item No 30 above but 25 mm bore tubing

Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified.

Ditto all as per ser item No 33 above but 20 mm bore tubing

Ditto all as per ser item No 33 above but 25 mm bore tubing

S & F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repairs stop cock/ anglecock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs concealed fancy type stop cock, chromium plated with long shank and cup of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed.

S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

S & F in repairs PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all per ser item no 44 above but as in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- all per ser item no 46 above but as in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F bands, straps, supports or stays for rain waterpipes, hooks (stay) heavy for large gates, hook and pintle hinges clamps, hold fasts wall ties, hooks for hanging fans and similar small articles Fe-290 Gde- E-165 or Fe-310-0 complete all as specifed and directed.

M&L for special treatment to sunken slab floor (Area of Sunken Portion n exc 1.50 Sqm) incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, etc after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

M&L for special treatment to sunken slab floor (bottam and vertical portion) etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 2000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected complete all as directed.

Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth

Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

S & F pressed steel door frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified,

M&L for factory made 35 mm thick IInd C/L H/W plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing.

S&F Powder coated aluminium anodised aluminium frame, shutters for door, windows, ventilators with one or more rebates including joining cleat for fixing etc, rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engr-in-Charge.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

S&F butt hinges medium weight cold rolled mils steel 100mm long.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long.

S&F aluminium anodised handle of extruded section 150mm long.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long.

S & F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

S & F Galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness size, quality or description) from wooden/ Steel frames glazed with putty or fixed with beads.

M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane.

M & L for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

M & L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide.

M & L for preparation of old steel surface and applying one coat of synthetic enamel paint.

S & F in repairs looking mirror of size 600 mm x 450 mm etc complete all as specified and directed by Engineer-in-Charge.

M&L for Full moulding/half moulding of stone slabs one edge, two edge, as in steps cooking platforms jambs and cills and other similar situations complete all as specified & directed.

S&F Chromium plated soap dish of Prayag polymers Pvt Ltd or equivalent

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete, including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Charge.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 12 module suitble for Mylinc series of Legrand including white plates with frame upto 12 module of make suitable for Mylinc Series ) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2.Wiring shall be done as per complaints recd from user only on required basis it is not necessary to do whole wiring of any whole bldg 3. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One fan point controlled by switch 5 Amp single pole one way

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

All as per ser Item No 82 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F in replacement Modular Switch, 6 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 16 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Socket Outlet 6 Amp, 3 pin, combined two module etc complete all as specified and directed by Engineer-in-Charge.

S&F Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module etc complete all as specified and directed by Engineer-in-Charge

Supply & fix lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

M&L ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs 4 way SPN, 240 volts concealed in wall, protection class IP-42, suitable for fixing of MCBs etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 200 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management, Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

Supply & fix MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fix MCBs, SPN, AC, 240 volts of 40 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

S&F in replacement industrial type ultra slim square profile LED lighting fixture, environmental friendly, energy efficient ready to use pack induastrial type LED Tube light fitiing 20 Watt with LED light source 6500 K, with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge .

S&F in replacement square profile LED lighting fixture with extruded environmental friendly, energy efficient ready to use pack LED Tube light fitiing 10 Watt with LED light source 6500 K,input voltage 140V-270V with uniform light output, with all accessories including its connection with 2 core seathed cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement energy saving and environmental friendly long life LED street light 35 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with & including twin core twisted flexible copper conductor cable of suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge

S&F sub main wiring with two single core PVC insulated, unsheathed, FRLSH stranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLSH stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge . Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit

Supply and fix exhaust fan, PVC body AC Single phase, 230 V of size 200mm sweep with ,blades and frame and heavy duty all as specified and directed by Engineer-in-charge

Avinash B Kullal (BID ID -3502699)

AZAD SERVICES (BID ID -3502716)

AMAR CONSTRUCTION (BID ID -3502865)

M/s. R. R. ASSOCIATES (BID ID -3502940)

Sunil Kanhoji auti (BID ID -3502537)

Arihant Construction (BID ID -3502730)

M/s A G Gund (BID ID -3502799)

BHAVIN INFRA (BID ID -3502958)

Maruti Abhiyantriki (BID ID -3502402)

M/S SANKET DADASAHEB KHOSE (BID ID -3502489)

Ms. M.D. Auty (BID ID -3502659)