Loading
Loading…
Loading…
Tender Value
₹73.7 L
EMD Value
₹1.5 L
Closing Date
6 May 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
Above/Below/Par
WA SECTION
71 conditions · 1 needing a document upload
Beam bottom's line, level & width should be checked.
Beam side's line , level & plumb should be checked.
Beam to beam measurements shall be checked as per architectural drawing.
Individual level & diagonal of each slab bay shall be checked.
Slab thickness level shall be marked with nails on the peripheral beam's outer side.
Slab thickness & beam depths should be checked
Support props for slab & beam bottoms should be in line & plumb, Bamboo bracing should be done at around 4' ht from floor level. Support props for double staging terraces shall be carefully checked.
Line of external/peripheral beam's side shall be checked & should be cross supported to avoid building out of sides.
Junctions of column & beam shall be checked & should be cross supported to avoid building out of sides.
De-shuttering oil shall be applied to beam/slab shuttering
Formwork of staircase shall be checked for dimensions of tread and riser, level of treads, plumb of risers.
Reinforcement shall be checked for beams and slab as per RCC drawing.
Proper cover for bottom/sides shall be checked for beams.
Proper cover shall be checked for slab.
Electrical points, electrical piping (conduits)/fan hooks shall be checked as per drawing.
Reduction of column as per drawing shall be done if any.
Proper no. of chairs shall be provided for slab.
Parapet (pardi) bars shall be left for balconies/staircase etc.
Ring (stirrups) shall be provided at the free end of each column reinforcement
Gaps between plates/planks should be filled. Taping should be done at ply joints in care of ply shuttering
Approval of architect and RCC consultant shall be taken prior to pouring.
Check the availability of required labour strength, mixer, lift, vibrators, masons, weigh batcher, diesel/petrol and plastics sheets etc. before start of concreting.
Hidden beams/inverted beams/cantilever beams should be checked.
Check for the sunk if any as per the approved drawings.
Packing below supports props should be avoided. If not, single wooden plank should be inserted as packing
In case of large slabs, position of concrete joints shall be decided in advance as per approval by RCC consultant.
Availability of raw material for concrete/RMC per grade of concrete, water. Electricity shall be checked in advance before the start of concreting.
Concreting shall be done for the beams first & then slabs.
Compaction of concrete shall be done by vibrators & tamping rods. (Spare vibrators with fuel shall be ensured.)
The top level of slabs shall be finished by the mason and no one should be allowed to walk on the fresh finished concrete.
Carpenter shall be present below the slab shuttering during concreting to ensure the tightness of the form work.
In case of rains, the finished concrete shall be covered with the big plastic sheets.
Cast 6 cube moulds for testing.
Curing the slab shall be done with pounding method by making ponds in cement & sand mortar(1.10) of size around 5'X5' curing of beams and slabs shall be done for 7 to 10 days or as directed by the consultant.
Date of casting and slab no shall be painted on the front side beam.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Labour Cooperative Societies shall submit only 50% of bid security for which the tenderers are required to upload Registration certificate issued by appropriate authority without which their offer will not be considered. Such firms should also declare that -" We are a Labour Cooperative Society and our Registration No. is .................... with .......................and hence required to deposit only 50% of Bid Security
Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' shall be exempted from payment of Bid Security on submission of Registration Certificate issued by appropriate authority. For such firms it is required to upload a copy of Registration Certificate issued by appropriate authority without which their offer will not be considered. Such firms should also declare that - I/We am/are a Startup firm registered by ........................ Department of Industrial Policy and Promotion (DIPP) and my registration number is ................ valid upto ...................... (Copy enclosed) and hence exempted from submission of Bid Security.
THE OFFERS WITHOUT EARNEST MONEY EXCEPT IN CASE OF EXEMPTION CLAIMED AS PER COMMERCIAL COMPLIANCE OF NIT WILL BE SUMMARILY REJECTED.
(A) Electrical General work in connection with Engg. work "Kurseong-Mahanadi:- Construction of Office-cum-Barrack at DHR-KGN-MHN". (B) Electrical General work in connection with Engg. work "UPGRADATION OF OFFICER REST HOUSE AT DARJEELING IN KATIHAR DIVISION (Old Building)". (C) Electrical General work in connection with Engg. work "UPGRADATION OF OFFICER REST HOUSE AT DARJEELING IN KATIHAR DIVISION (New Building)".
22-2026~NFR
22-2026
Open
Works - General
10 Months
Kota, Rajasthan
₹0
₹1.5 L
6 May 2026
15 Apr 2026
22 Apr 2026
99 items across 6 schedules · ₹50,23,400.01 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Repairs to various types of engine radiators of cummins, Deutz, Caterpillar etc. model nos. fitted in the different type of Track machines with all contractor's men, material, tools & plants etc. as directed by engineer-in-charge. Note:-1 Radiator will be handed over to the contractor by railways. 2. No transportation charges will be paid in case of repairs to be carried out outside the premises of STMD/KOTA. 3. The chemicals used for cleaning of radiator should not damage the radiator parts and incase of damage, the contractor has to repair such cleaning of radiator tubes with suitable chemicals without damaging the core and tubes. | Numbers | 5.00 | 17,274.64 | 86,373.2 |
| 2 | Supply and fitment of laminated safety glass 6mm thick in working/driving cabin as per the standard specification laid down for track machine. Working includes removal of old glass and fitment of new glass by changing rubber bidding etc. The cost is inclusive of glass, rubber bidding etc. | Square Foot | 100.00 | 316.57 | 31,657 |
| 3 | Supply and fixing 19mm thick water proof, heat resistance 19mm thick ply including 2mm thick PVC sheet on the floor of track machine by properly securing the seat in position using suitable size screw/rivets. The rate shall be inclusive of removing existing ply /checkered sheet ,cost of screw, riveting etc. | Square Foot | 200.00 | 124.15 | 24,830 |
| 4 | Supply and fitment of rubber beading (70 shore grade rubber pad ) in frames of various types of cabin doors and windows so as to make the door/window housing dust prove .The work includes removal of old/ damaged bidding, surface preparation etc. | Foot | 500.00 | 35.02 | 17,510 |
| 5 | Recoupment of nitrogen gas of accumulator fitted in track machine using contractor's nitrogen gas, cylinder etc. Capacity of the accumulator is 32 liter & final pressure for refilling nitrogen gas will be provided by Railway for refilling work. Note: Rate for similar capacity accumulator will be suitably reduced on prorate basis. | Numbers | 10.00 | 919.09 | 9,190.9 |
| 6 | Supply and fixing wiper blades on safety glasses of various cabins of track machine (12"to 26") | Numbers | 5.00 | 448.6 | 2,243 |
| 7 | Repairing of accumulator defective valve | Numbers | 2.00 | 72,215.56 | 1,44,431.12 |
| 8 | Repairing of accumulator by replacement of defective bladder (Make- Hydec), replacement of valve & all other accessories, gas filling, and complete overhauling | Numbers | 3.00 | 96,287.41 | 2,88,862.23 |
| 9 | Repairing, fitting, overhauling, refilling of gas, leakage testing etc. cost of valve bladder seal kit and anti-extrusion ring if required during repairing will be paid separately as per relevant item of the schedule. | Numbers | 6.00 | 5,470.86 | 32,825.16 |
| 10 | Re p a i r i n g of roof top-air- conditioning by replacement of defective compressor, (part no. 435-55017) Make-Valeo or Webasto. | Numbers | 3.00 | 67,273.79 | 2,01,821.37 |
| 11 | Supplying and fixing of 24VDC axial fan for roof top AC of Track Machine | Numbers | 3.00 | 15,500 | 46,500 |
| 12 | Repairing, fitting, Overhauling, refilling of gas R- 134a, Ieakage testing etc. Cost of V- ribbed belt, if required during repairing will be paid separately | Numbers | 3.00 | 7,344.19 | 22,032.57 |
| 13 | Repairing seat of track machines (both sitting portion and back) by replacement of existing 6" thick cushion with new 6" thick cushion including repairing of sliding arrangement and side handles complete. | Numbers | 25.00 | 2,153.12 | 53,828 |
| 14 | Supplying and fixing seat cover of thick cotton on driving seat and working cabin seat as approved by engineer-in-charge. | Numbers | 50.00 | 678.38 | 33,919 |
| 15 | Providing and fixing of curtain/Roller blind (curtain) in front of glass windows except on door with steel rod, rings etc. The material should be approved by Engineer- in-charge. | Numbers | 50.00 | 6,139.54 | 3,06,977 |
| 16 | Supply and fitment of bearing part number 32009X make FAG or equivalent. | Numbers | 50.00 | 1,041.21 | 52,060.5 |
| 17 | Supply and fixing of Bench vice (Make:- Unique/Taparia) (10"/250 mm) | Numbers | 2.00 | 22,958.34 | 45,916.68 |
| 18 | Supplying fabricating and fixing plates of EN materials confirming to EN-19 | Kg | 200.00 | 193.3 | 38,660 |
| 19 | Supplying fabricating and fixing plates of EN materials confirming to EN-24 | Kg | 200.00 | 211.7 | 42,340 |
| 20 | Supplying fabricating and fixing plates of EN materials confirming to EN-31 | Kg | 100.00 | 230.12 | 23,012 |
| 21 | Supply and fitment of rubber beading for roof as per sample Make EPDM rubber. | Metre | 100.00 | 576.99 | 57,699 |
| 22 | Repairing of Lifting and Lining Unit as per schedule of work (All Machines) | Numbers | 4.00 | 1,01,378.43 | 4,05,513.72 |
| 23 | Repairing and overhauling of welding generators provided for different big track machine. | Numbers | 5.00 | 20,828.65 | 1,04,143.25 |
| Schedule total | ₹20,72,345.7 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .