Construction of district library in (Bapod) East Zone area of VMC ( Fourth Trial)

NAME OF WORK : NEW CONSTRUCTION WORK Of DIST. LIBRARY AT EAST ZONE , VADODARA FOR VADODARA

SCHEDUAL B SHEET

NO. DESCRIPTION QTY UNIT RATE. AMOUNT

Excavation for foundation upto 1.5 mt including sorting out and stacking of

useful materials and dewatering, disposing of the excavated stuff from 0 to

1 50mt within VMC Limit. (A) Loose or soft soil 1568 Cum 120

Excavation for foundation for depth from 1.5 m to 3.0 m

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

2 Dense or Hard soil 792 Cum 166

Filling in foundation and plinth with murrum or selected good soil (from

outside) in layers of 20 cm thickness including watering, ramming and

3 consolidating etc. completed.(upto 10 ton) 246 Cum 296

Filling with available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20 cm, in depth

4 consolidating each disposited layer by ramming and watering. 1684 Cum 134

Filling in plinth with sand under floors including watering ramming,

5 consolidating and dressing complete 72 Cum 472

Providing and laying rubble for appron (each stone weighting not less than

40Kg.) including and packing and filling in the interestices with quarry-

6 spalls. 309 Cum. 1067

Carrying out plinth treatment to post construction / existing structure by

spraying chemical solution for termite control treatment including labour

and material consistent with I.S.I specification. (Plinth Area will be

7 measured for payment purpose) 750 Sqmt. 97

Add extra for Disposing off the excavated stuff of above items for lead

8 of 0.5 k.m. to 3 k.m 277 Cum 129

Providing and laying cement concrete 1:3:6 ((1 cement :3 coarse sand:

hand broken stone aggregates 40 mm nominal size) and curing complete

9 excluding the cost of formwork in foundation and plinth( more than 10 ton) 83 Cum 3081

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8-

hand broken stone aggregates 40 mm nominal size) and curing complete

10 excluding cost of formwork in foundation and plinth 28.1 Cum 2747

Providing and laying controlled cement conceret M250 (Considering

minimum cement content 360 Kg/Cumt.) and curing complete excluding

the cost of formwork, centering, shuttering, Scaffolding, stuting and

propping etc. in shape and size and removal of the same etc. complete at

all levels as directed by EIC.

Foundation, Footing, base of column and Mass Concrete (more than

11 tone ) 294 Cmt. 4248

Providing and laying controlled cement conceret M250 (Considering

minimum cement content 360 Kg/Cumt.) and curing complete excluding

the cost of formwork and reinforcemnet for reinforced concrete work in: as

directed by EIC.

12 Columns, Pillars posts and struts(more than 10 tone ) 64 Cmt. 4628

Providing and laying controlled cement conceret M250 (Considering

minimum cement content 360 Kg/Cumt.) and curing complete ,excluding

the cost of formwork and reinforcemnet for reinforced concrete work in: as

directed by EIC.

13 Tie Beams, Girders and cantilever at ground level(more than 10 tone ) 153 Cmt. 4527

Providing and laying in position Ready Mixed M-300 grade

concrete for reinforced cement conctere work , using cement

content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for a lead up to 10 kms having continuous

agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, excluding the

cost of centering shuttering finishing and reinforcement

including cost of admixtures in recommended proportions as

per IS: 9103 to accelerate/ retard setting of concrete, improve

workability without impairing strength and durability as per

direction of the Engineer - in - charge. Without Fly Ash (Min

cement level as per latest IS 456 shall be maintained)

14 (Cement level 475 kg ) 63.45 Cmt. 5093

Providing and laying controlled cement conceret M200 (Considering

minimum cement content 340 Kg/Cumt.) and curing complete excluding

the cost of formwork, centering, shuttering, Scaffolding, stuting and

propping etc. in shape and size and removal of the same etc. complete at

all floor and all levels as directed by EIC.

15 Slabs, landing, Shelves, Balconies (more than 10 tone ) 115 Cmt. 4461

Providing and laying controlled cement conceret M200 (Considering

minimum cement content 340 Kg/Cumt.) and curing complete excluding

the cost of formwork, centering, shuttering, Scaffolding, stuting and

propping etc. in shape and size and removal of the same etc. complete at

all floor and all levels as directed by EIC.

16 lintel 9 Cmt. 4461

Providing formwork of ordinary timber planking so as to give a rough finish

including centering, shuttering, strutting and propping etc. height of

propping and centering below supporting floor to cealing not exceeding

M. and removal of the same for in sity reinforced concrete and plain

concrete work in. (A) Foundations, Footings, Bases of Columns etc., and

17 Mass concrete.(more than 10 tone ) 373 Sq.M. 179

Providing formwork of ordinary timber planking so as to give a rough finish

including centering, shuttering, strutting and propping etc. height of

propping and centering below supporting floor to celiling not exceeding

M. and removal of the same for in sity reinforced concrete and plain

concrete work in. (B) Flat surfaces such as soffits of slabs, Landings and the

18 like. (1) Floors, etc. upto 200 mm in thickness.(more than 10 tone ) 118 Sq.M. 261

Providing formwork of ordinary timber planking so as to give a rough finish

including centering, shuttering, strutting and propping etc. height of

propping and centering below supporting floor to celiling not exceeding

M. and removal of the same for in sity reinforced concrete and plain

concrete work in. (G) Columns, Pillars,Posts and struts. (1) Square,

19 Rectangular, Polygonal in plan.(more than 10 tone ) 365 Sq.M. 313

Providing formwork of ordinary timber planking so as to give a rough finish

including centering, shuttering, strutting and propping etc. height of

propping and centering below supporting floor to celiling not exceeding

M. and removal of the same for in sity reinforced concrete and plain

concrete work in. (H) (1) Sides and soffits of Beams, Beam Haunchings,

cantilevers, Girders, Bressumers and Lintels not exceeding 1 M. in

Depth.(more than 10 tone )

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering

strutting and propping etc. height of propping and

centering below supporting floor to ceiling not exceeding

4 M. and removal of the same for in situ reinforced

concrete and plain concrete work in. (I) Edges of slabs

21 and Breaks in floors and walls. 19 Sq.M. 72

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

22 bending, binding and placing in position complete upto floor two level 80772 kg 77

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine

23 sand)(B) Conventional 4 Cmt. 4153

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:6 (1- Cement : 6 -fine sand) Extra for brick work in superstructure

above plinth level upto floor two

24 level (B) Conventional 102 Cmt. 4122

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement: 4 -coarse sand ) in foundation and plinth ,Extra for brick work in

superstructure above floor two level Item No.

25 (B) Coventional 45 Sqmt. 615

Providing 15 mm thick cement plaster in single coat (Interior Plaster) on

Brick/c.c wall for plastering at all floor and all levels and finishing even and

26 smooth in cement mortar 1:4 etc complete as directed by EIC. 483 Sq.Mt 171

Providing 20mm thick cement plaster in single coat on single or half brick

walls for interior plastering upto floor two level and finished even and

27 smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) 647 Smt 218

Finishing walls with textured exterior paint of required shade :

13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm)

over and including priming coat of exterior primer applied @

Finishing wall with weather proof exterior emulsion paint (with 7yrs.

warranty period) on plastered surface (two coats) to give an required shape

even shade after thoroughly brushing the surface to remove all dirt and

remains of loose powdered materiels etc complete at all floors and all

29 levels as directed by EIC. 1130 Sq.Mt 117

Applying two coats of Birla or Asian acrylic lappy (putty) and two coats of

primer of approved brand and manufacture on new wall surface to give an

even shade including thoroughly brushing the surface free from mortar

dropping and other foreign matter and sand prepared smooth etc complete

30 at all floors and all levels as directed by EIC. 447 Sq.Mt 41

Wall painting (3 coats) with plastic emulsion paint of approved brand and

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar dropping and other

foreign matter and sand papered smooth etc complete at all floors and all

31 levels as directed by EIC. . 483 Sq.Mt 115

Providing and fixing Structural Glazing with using the 17 Micron anodised

of approved colour alluminium section as transium, mullium of size 63mm

x 38mm x 2 mm with using 6 mm thick reflective structural glass of

approved make, colour, toughned and shade and fixed with silicone sealant

and spacer tap and at corner sealed neoprene foam dust and Air sealed

gasket mirred including scaffolding, cleaning of glass etc.complete at all

heights anf lifts with all necessary fitting and fixtures, anchore fasteners,

necessary M.S. or Aluminium brackets, suitable design for openable

window as per Architectural drawing and as directed by Engineer-in-

charge. Grooves between the glasses to be filled with sealant of Dow

corning - structural sealant 995, weather sealant 789. The entire facade

should be water proof. The mullions are to be connected to bracket by SS-

304 nut bolts. Measurement shall be given as per actual execution of the

32 work. 52 Sqmt 3204

Pro. And fixing single layer water proof gypsum board 12.5 mm thick

sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm

suspended by GI suspender channel of size 25 mm x 3 mm with

intermediate channel og size 18 mm x 40 mm x 0.8 mm at 1220 mm center

to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c

and perimeter channel A of size 20 mm x 27 mm x 30 mm

x 0.5 mm at edges & drops incl.paper tap sand sofit cleat, anchor fastener,

scoch bolt connecting cleat,joining compound top coat on ceiling

incl.making necy.opening for light fitting,diffuser etc. comp. as per detail

33 drawing as directed 423.5 Sqmt 607

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base

of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface, tread of

steps, landing or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc. complete

34 for light shade (upto 10 ton) 446.6 Sqmt 1453

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc. complete

35 for antiskit 22 Sqmt 1433

Vitrified Wall Tiles :

Providing and laying Vitrified tiles 8 to 10 mm thick , in skrting risers of

steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse

36 sand) and jointed with white cement slurry 72 Sq.Mt 1577

Providing and laying Granite stone flooring in required design and patterns,

in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab and 75mm width

granite acid work stripe stone over 50 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry

and pointing with whitecement slurry admixed with pigment of matching

shade including moulding, rubbing, curing and polishing etc. all complete

as specified and as directed bythe Engineer-in-Charge :a. Flamed finish

granite stone slab Jet Black, Cherry Red, Elite Brown,Cat Eye or equivalent

37 as approved by Architect. 8 Sqmt. 2697

Providing and fixing 18 mm thick Granite gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms,

vanitycounters, window sills , facias and similar locations of required size,

approved shade, colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including moulding,

rubbing, curing, and polishing to edges to give high gloss finish etc.

complete at all levels.

38 8.2.2.2 Area of slab over 0.50 sqm 52 Smt. 2697

Supplying cutting, bending, binding and placing in position steel as per plan

and design and as per ISS 2502 including cost of steel and binding wire for

reservoirs/structures only including lift up to 6 meter height or depth

below G.L. for all diameters CRS steel all diameter Fe 500grade confirming

39 to relevant I.S 3490 Kg. 79

PROVIDING & LAYING 80MM THK.RUBBER MOULDED

INTERLOCKING PAVER BLOCKS(M-45 GRADE) 50 MM

THICK SAND BED INCL. COMPACTION WITH MECH.

COMPECTOR IN LINE , LEVEL AND COLOUR AND DESIGN

40 AS SELECTED BY ENGINEER INCHARGE (APPROVED R.A. 170 SQM 789

Providing and fixing pre-cast concrete kerb stone of gray cement based

concrete block 30cm length,30cm height and 15cm thick of M250

grade concret as per approved design and including excavation for

fixing in proper line and level,filling the joint with C:M 1:3

41 (1cement:3fine sand) etc complete. 48 Sq.Mt 371

Provoding and fixing flush door shutters, solid core construction with frame

of first class hardwood with cross band and face veneer or plywood face

panels,laminate,Batten patti including anodised alluminium butt hinges

eith necessary screws. (B) Non-decorative type and block board core

42 anodised alluminium butt hinges in flush door shutters (2) 35 mm thick. 9 Sqmt. 1830

Providing and fixing FRP frame size 100x50mm and 28mm thick FRP

depress panel shutter having extra reinforcement on sides & edges in Gel

coat finish. The core of the shutter & frame is to be filed up with injected

fire retaedant grade polyurethen form done in situ alongwith embedded

wooden piece for stiffening & also taking hinges & fintures. The whole FRP

frame & shutter is to be water proof weather proof, termite proof &

resistance to mild acid/alkali. Rates are to be inclusive of S.S. hinges with

43 necessary screws & alluminium fixtures & fastenings & fastener sleeved. 9 Sqmt. 2378

Providing and fixing standared extruded of alluminium section of size

63mm x 38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with colour anodized

alluminium frame for ventilation with 5 mm thick frosted glass as details

44 etc complete for Ventilation 17 Sq.Mt 1176

Providing and fixing standared extruded of alluminium

section of size 63.50 x 38.10 x 1.95 mm @ Wt 1.094Kg /

Rmt with colour anodized alluminium frame with 5 mm

thick transparent bronze colour tinted float glass with

colour anodized alluminium frame for ventilation with

mm thick frosted glass as details etc complete

45 for.window 301 Sq.Mt 1176

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 95mm x 24mm x 1.17mm (of Jindal Section

no:2459 @ wt.of 0.738 Kg/mt), horizontal Three track member size 92mm

x 31.75mm x 1.30mm (of Jindal Section no:8688,@ Wt.1.07 Kg/mt), vertical

member of size 92mm x 31.75mm x 1.50mm (of Jindal Section no:8933,@

Wt. 1.06 Kg/mt) with sliding shutters of horizontal member size

mmx18mm x1.29mm (of Jindal Section no:8947@ wt.of 0.456 Kg/mt),

vertical member of size 40mm x 18mm x 1.29 mm (of Jindal Section

no:8949 @ wt.of 0.456Kg/mt/ with 5 mm th transparent bronze colour

tinted float glass with powder coated aluminum fittings & fixtures and

46 transparent silicon sealant glass fixing to frame as per details etc 27 Sqmt. 1592

Providing and fixing M.S. grills of required pattern of windows etc. with

M.S. flats at required spacings and frame alround, square or round bars

47 with round headed bolts and nuts or by screws. (A) Plain Grill. 951 mt 105

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

48 and sand paper with ready mixed priming paint brushing red lead. 12 Sqmt. 36

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the surface

49 of all dirt, dust and other foreign matter. 12 Sqmt. 90

PROVIDING AND FIXING CARPET LAWN IN BLOCKS

INCLUDING FIXING WITH FERTILIZER AND CLAY, WITH

ALL TRANSPORTATION, PLANTING ETC

50 COMPLETE.(APPROVED R A of

Preparing structural design ) RCC Under Ground / Partially under ground / 100 Smt 311

above high ground level Reservoir of required capacity as per relevant I.S.s

and constructing the same, including excavation in all types of soil strata

(including rock) including shoring strutting if required, for loose soil / to

protect from collapse due to near by traffic load, casting 100 mm thick

P.C.C., levelling course in M-10, Refilling the pit with proper soil and

disposing of the surplus stuff within a lead of VMC limit, Including cement

plaster in CM 1:2 with approved water proofing compound to inside water

touching surface to container. Including all types of labour and material

charges of lowering, laying, erecting / hosting and jointing of pipe assembly

to inlet, outlet overflow, washout and byepass arrangement as per

hydraulic design.

Providing and fixing accessories like MS / GI ladder, CI Manhole frame and

cover, Water level indicator, adequate cowl type ventilators or lantern type

ventilator with stainless steel jail.

B.B. Masonry chambers for valves, Providing and applying three coats of

cement paint / snowcem to the outside face of structure. It also includes

51 satisfactory water tightness test as per relevant I.S. code and painting 20000 LIT 8

Providing erecting fixing double coated Syntex of Equivalent PVC (ISI) Mark

water tank of required capacity each with all necessary fittings &

52 connection etc.complete on terrace. 20000 Lit 4

Providing and fixing white vitreous china pedestal type water closet

(European type W.C. pan) with seat and lid, 10 litre first quality low level

concealed flushing cistern, including flush pipe, with manually controlled

device (handle lever), conforming to IS : 7231, Jet spray & conceal cock

with all fittings and fixtures complete, including cutting and making good

the walls andfloors wherever required :

53 17.2.1W.C. pan with ISI marked white solid plastic seat and lid 3 Nos. 1336

Providing and fixing wash basin with C.I. brackets, 15 mm S .S . pillar taps,

32 mm C.P. brass waste of standard pattern, includingpainting of fittings

and brackets, cutting and making good the wallswherever require :

17.7.3 White Vitreous China Wash basin size 630x450 mm witha pair of

54 mm S S pillar taps 2 Each 1317

Providing & Fixing urinal of approved quality incl. connection the urinal

with waste pipe, trap,nessesary PVC connection, (A) White Earthenware

55 flact back or corner typesize 430mm x 260mmx 350mm 2 No. 1062

Providing & fixing S S Plated pillar tap, capstan head,screw down high

pressure with screws, shanks and back nuts. pillar cock long neck with

56 aerator - 15mm dia 3 Each 309

Providing and fixing 15mm dia S S Plated screws down Bib Tap etc.

57 complete 5 Each 187

Providing and fixing chromium plated brass half trun flush

cock of approved quality including fixing in pipe line etc.

58 complete.(iii) 32mm dia. 6 No. 3131

Providing and fixing PVC Nahni trap of the following nominal diameter of

self cleaning design with C.I. screed down or hinged gratiing incl. cost of

cutting & making, good the walls and floors 100 mm inlet and 50 mm

59 outlet. 6 Each 633

Providing & fixing 600mm x 750 mm bevelled edge mirror of superior glass

mounted of 6 mm th. PVC sheet or plywood sheet and fixed to wooden

60 pluge with C.P. brass screws and washer 3 Each 855

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets

61 fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size. 3 Each 616

Providing and fixing PTMT soap Dish Holder having length of 138mm,

breadth 102mm, height of 75mm with concealed fitting arrangements,

62 weighing not less than 106 gms 3 Each 782

Providing and laying in trenches galvanised mild steel tubes (Midium grade)

of the following nominal bore, and tube fitting including fixing, testing of

pipe with joints and also including the cost of necessary fitting etc.

complete as directed by E.I.C. (If Pipe shall be fixed on the wall, so It have

to fixed with the help of clamp at every two meter c/c. or shall be

concealed ) (Earthwork in trenches to be measured and paid for separately)

: 65mm dia.(more than 10 tone)

Providing and jointing in true line and level UPVC pipe (SCH :40) including

fitting make or equivalent as approved by Engineer In Charge Pipe shall be

fixed on the wall with the help of clamp at every two meter c/c. or shall be

concealed as directed including necessary fitting etc. including testing of

pipe and joints and fixing the same with adhesive solvent, including cost of

64 all materials. 50mm dia. 60 Rmt. 196

Providing and jointing in true line and level UPVC pipe (SCH :40) including

fitting make or equivalent as approved by Engineer In Charge Pipe shall be

fixed on the wall with the help of clamp at every two meter c/c. or shall be

concealed as directed including necessary fitting etc. including testing of

pipe and joints and fixing the same with adhesive solvent, including cost of

65 all materials. 25mm dia. 24 Rmt. 92

Providing and jointing in true line and level UPVC pipe (SCH :40) including

fitting make or equivalent as approved by Engineer In Charge Pipe shall be

fixed on the wall with the help of clamp at every two meter c/c. or shall be

concealed as directed including necessary fitting etc. including testing of

pipe and joints and fixing the same with adhesive solvent, including cost of

66 15mm dia. 65 Rmt. 73

Providing, fixing, jointing, testing and commissioning of UPVC pipe with

rubber ring joint confirming to IS : 13592, and confirming to IS : 4985 (Pipe

Class III - 6 kg / sq.cm) cut to required lengths including all necessary

fittings and specials such as bends, junctions offsets, access pieces (plain or

door) . Fixing at wall / ceiling level supported by G.I. clamps, hangers etc.

duly epoxy coated. Cutting chases/holes in floors/walls / slab. The piping

67 should be complete with P or S trap as req. 110mm (10.0 Kg. F/Cm2 15 Rmt 856

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working

pressure polythene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

68 including making good the wall ceiling and floor.(F) 75mm(10.0 Kg. F/Cm2 8 Rmt 280

Providing and fixing Gun metal check or non-return fullway

69 wheel valve.(E) 40mm dia.(23.99) 4 Each 663

70 Providing and fixing Slotted cowl (terminal guard ) 110 mm dia 4 Nos. 20

71 Providing and fixing Slotted cowl (terminal guard ) 75 mm dia 4 No. 9

Providing & fixing S.W. Gully trap with C.I. grating brick masonry chamber

& water tight C.I. cover with frame of 300 mm x 300 mm size ( inside) with

72 standard weight. (B) 150 mm x 100 mm size 'P' or 'R' type 5 NOS. 1292

Constructing brick masonry chamber for underground C.I. inspection

chamber and bends with brick having crushing strength not less than

Kg./Cm2. in C.M. 1 : 5 C.I. cover with frame (light duty) 455 x 610 mm.

internal dimensions, total weight of cover with frame to be not less than

Kg. (Wt. or cover 23 Kg. and Wt. of frame 15 Kg.) R.C.C. top slab with C.C.

: 2 : 4 mix (1 cement : 2 coarse sand : 4 graded aggregate 20 mm. size)

foundation concrete 1 : 5 : 10 inside plaster 15 mm. thick with C.M. 1 :

finished smooth with a finishing coat of neat cement on walls and bed

concrete etc. complete. ( Inside Dimensions 500mm x 700 mm & 450 mm

73 deep for single pipe lines with one or two inlets. 5 Each 3661

Extra over items 24.44 for every additional depth of 0.1M. of part thereof

beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm

74 size. 5 Each 265

Construction Manhole with 150mm th. R.C.C. top slab in 1 : 2 : 4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm. nominal size)

foundation concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 brick bats 40 to

50 mm. size) inside plastering 15 mm. thick with C.M. 1 : 5 (1 cement :

coarse sand) finished with floating coat of neat cement and making

channels in C.C. 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate

mm. nominal size) finished smooth complete incl. curing and testing (1)

inside size 900 mm. x 1200 mm. and 1.5 mt. deep including C.I. cover with

frame size.560 mm diameter total weith of cover & frame to be not less

than 128 kg, (Wt. of cover 64 kg. & Wt. of frame 64 kg) (A) with 230 mm

th. Walls of brick masonry using brick having crushing strength not less

than 35 kg./Sq.cm in cement mortar 1 :5 (1cement : 5 coarse sand)

75 (2) B type depth 1.50 Meter for 150mm diameter sewer. 2 Each 19350

(II) Extra rate for constructing B.B. masonry for every additional depth of

0.1M. GR Part thereof over item No.24.27 (I) for depth from 1.50M. to

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-

Graded stone aggregate 40mm nominal size) bedding for stoneware pipes

of following internal diameters with necessary formwork and curing

77 complete. (B) 150mm dia. (166mm Ave. bed thickness 22 Rmt. 214

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-

Graded stone aggregate 40mm nominal size) bedding for stoneware pipes

of following internal diameters with necessary formwork and curing

78 complete. (A) 100 mm dia. (112 mm Ave.bed thickness) 44 Rmt. 127

Providing and laying (to level or slopes) and jointing with stiff mixture of

Cement Mortar in proportion 1:1, Salt glazed stoneware pipes including

79 testing of pipes and joints complete. (B) 150mm dia.(more than 10 tone) 44 Rmt. 214

Providing and laying (to level or slopes) and jointing with

stiff mixture of Cement Mortar in proportion 1:1 Salt glazed

stoneware pipes including testing of pipes and joints

80 complete. 200mm dia 66 Rmt. 313

Providing and Supplying ISI standard RCC pipes (of Sulphate Resistance

Cement ) in standard length of following class and diameter suitable for

Rubber ring joint including all taxes,insurance ,transportation ,freight

charges,octroi,inspection charges ,loading ,unloading ,conveyance to site

/Departmental store ,stacking etc. complete .(IS-458/1989,suitable for

tyton joint including cost of supply of joint mat,rubber ring . for Horizontal

81 cast /vertical cast as mentioned. 300 mm dia 33 Rmt. 727

Providing and Supplying ISI standard RCC pipes (of Sulphate Resistance

Cement ) in standard length of following class and diameter suitable for

Rubber ring joint including all taxes,insurance ,transportation ,freight

charges,octroi,inspection charges ,loading ,unloading ,conveyance to site

/Departmental store ,stacking etc. complete .(IS-458/1989,suitable for

tyton joint including cost of supply of joint mat,rubber ring . for Horizontal

cast /vertical cast as mentioned.

82 450 mm dia 22 Rmt. 1659

Lowering laying and jointing RCC pipe for Rubber ring push on joint with

CM 1:1.5 vata of following diamtere including excavation in proper

position,grade alignement as directed by Engineer in charge includig

conveyance from store to site of work , all labour complete . ( Including

performing sucessful flow test ) including all cost of jointing material

83 300mm dia 33 Rmt. 120

Lowering laying and jointing RCC pipe for Rubber ring push on joint with

CM 1:1.5 vata of following diamtere including excavation in proper

position,grade alignement as directed by Engineer in charge includig

conveyance from store to site of work , all labour complete . ( Including

performing sucessful flow test ) including all cost of jointing material

84 450mm dia 22 Rmt. 173

Providing and fixing stone slab with table rubbed, edges rounded and

polished, of size 750mm (h) x500 mm (w) and 18 mm thick, fixed in Urinal

Partitions by cutting a chase of appropriate width with chase cutter and

embedding the stone in the chase with epoxy grout or with cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm

nominal size) as per direction of Engineer-in-charge and finished smooth.

85 8.10.2 Granite Stone of approved shade 1 Sqmt. 2697

Providing And Placing: Fix Multi-Purpose Fabric Chair Specification: Office

Seating Type: * All Over Size Is : 580mm(L)X 760mm(D)X 930mm(H) , *The

Chair Made Of Full Fabric In Black Colour . It Will Comes In Matte Finish In

Contemporary Style. Details: * Arms: Fixed Armrests. * Use Of Ply: 12 Mm

Thick Hot Pressed Bwr Plywood (Is Grade - 303 For Seat And Back) . * Seat:

40 ± 2 Mm Thick Polyurethane Foam With Density 32 (±3) Kg Per Cu Meter

For Best Quality Cushioning In Seat, * Back : 40 ± 2 Mm Thick Polyurethane

Foam With Density 32 (±3) Kg Per Cu Meter For Best Quality Cushioning In

Back . Backrest Support Foam Design Based On Symmetrical Lumbar

Support Seat Max Height Is @ 930mm . * Base : 4 Legs Metal Powder

Coated . * The Product by The Seller / Company Should Be Iso 9001:2008,

guard, Green Pro, Aiota, Indian Design Mark And Fsc Certified. The Bidder

Should Be A Member Of Bifma And At Least Two Products Of The Oem

Should Be Certified As Bifma Compliant And An Official Product Official

Link/Screenshot Of The Product Listing Must Be Provided From

86 Www.Bifma.Org". 122 nos. 2649

Providing & making computer table of requred size 0.75 mt width including

keyboard slide channel board cup board cpu cabinet with lock ,handle, top

87 laminate ,border putty and colour etc complete 28.8 RMT 4373

Providing and supply 2 Door Sliding Cub Board-LIB 1003 - Size: 1981 x 914 x

483mm Steel LibraryCupboard construction CRCA sheet 20 Gauge, Door

Outer Body CRCA sheet 22 gauge, Door partli 4mm thick visible gass with

and locking mechanism with hardware. with 4 adjustable shelf CRCA

making five comparments, Uniformly Distributed load capacity per each

40 Kg maximum, finished with epoxy powder coated to the thickness of

88 microns, including all necessary fixtures, fastners machinary etc. 6 nos. 12373

Supplying & placing in position of table of size:- L-1500mm x D-900mm x H-

750mm as per photograph.The table top shall be made out of25mm thk.

PRELAMINATED PARTICLE BOARD tabletop with PVC edge banding.

Tabletop supported with Powder coated "C" shape metal legs of size

50mm x 50mm and connectors of size 40mm x 40mm. . The product shall

be from ISO 9001:2015,ISO 50001:2011, ISO 14001, OHSAS 18000 , BIFMA,

FSC, AIOTA, SEDEX & Greenguard Certified company and complete as per

89 the approved sample and as per the direction of Engineer-In-Charge. 23 Nos. 18433

Steel work, welded in built up sections framed work including cutting,

hoisting, fixing in position and applying a priming coat of red lead paint.

(A)In beams and joists, channels angles Tees, flats, with connecting plates

or angle cleats as in main and cross beams. Hip and jack rafters, purlins

90 conneted to common rafters and the like 22.34 Q 9108

Providing and laying precast terrazo tiles 20mm thick with marble chips of

sizes. upto 6mm in skirting and risers of steps not exceedings 30 cms. in

height on 10mm thick cement plaster 1:3 (1-cement : 3- coarse sand )

jointed with neat cement slurry including rubbing and polishing complete

91 with tiles of. (A) Light shades using white cement 806 Sqmt 667

Extra over items for providing and mixing water proofing materials in used in

92 cement mortar in proportion recommended by the manufacturer 170 mix 49

Providing and fixing 12 mm thick frameless toughened glass door shutter

of approved brand and manufacture, including providing and fixing top &

bottom pivot & double acting hydraulic floor spring type fixing

and making necessary holes etc. for fixing required door fittings, all

complete as per direction of Engineer-in-charge (Door handle, lock and

93 stopper etc.to be paid separately). 300.7 SQ.MT 5379

6Supplying and fixing 6 Kg ABC type fire extinguisher suitable for residential

use, ISI marked as per IS:15683, filled with mono ammonium phosphate-

based dry chemical powder, suitable for Class A (solid), Class B (liquid), and

Class C (gas) fires. The extinguisher shall be complete with pressure gauge,

discharge hose/nozzle, safety pin, wall mounting bracket, and operating

instructions printed on the body. It shall be of approved make (such as

Safex / Ceasefire / Kanex / Minimax or equivalent), having a minimum fire

rating of 3A:40B, with at least one year warranty. The item rate shall

include all taxes, transportation, installation at site, and demonstration to

94 the user. 22 Nos. 3156

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth continuity

of following type, erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete(catIII)

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of

sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires, in below type of pipe to be erected complete

with earth continuity and necessary connection with primary light with

accessories erected on Metal / PVC / wooden box covered with 3 mm

thick PC(Polycarbonate) / Acrylic sheet for open / concealed wiring. with

necessary Lamp holder / ceiling rose / H.D.Connector as directed.

Note:- Maximum up to 6 mtrs length, excess will be considered as Mains

for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

96 wall/ceiling complete. 20 nos 153

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green)

both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand

copper wires, in below type of pipe erected with 6A Modular type switch

and hum free EME four or more step type electronic fan regulator with

separately mounted and accessories with earth continuity of following

type erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured/metallic front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and accessories erected

97 concealed in wall/ceiling complete. cat III. 60 nos 635.46

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires erected in below type of pipe with 6A

Modular type switches and following type of accessories erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate modules erected on / in wall / ceiling as per pipe

erected. with necessary batten/angle holder or ceiling rose or

H.D.Connector as directed. (f) with medium class Rigid PVC pipe and

98 accessories erected concealed in wall/ceiling complete. cat III. 10 nos 566.1

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules erected on /

99 in wall / ceiling with following type accessories. cat III. 30 nos 243.78

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box

covered with appropriate front plate modules erected on / in wall / ceiling

as per pipe erected with following type of accessories. [I] For 6A Plug with

2-1.5 sq.mm Cu. Wire.(f) with medium class Rigid PVC pipe and accessories

100 erected concealed in wall/ceiling complete. cat III. 12 nos 478.38

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper

wires, in below type of pipe erected complete with Modular type switch &

5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [II] For 16A Plug with 2-2.5

sq.mm Cu. Wire. (f) with medium class Rigid PVC pipe and accessories

101 erected concealed in wall/ceiling complete. cat III. 20 nos 704.82

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper

wires, in below type of pipe erected complete with Modular type switch &

5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [III] For 16A Plug and 16 amp

switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green) earthing wire

from mcb d b board.. (f) with medium class Rigid PVC pipe and accessories

102 erected concealed in wall/ceiling complete. cat III. 12 nos 826.2

Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered

with textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

103 3 nos. 6A 5 pin Plug . For Modular Type Accessories. Cat III. 35 nos 1092.4

SITC of Face Plate - Single (Keystone Jack,square) (Including Five year free

104 maintenance with guarantee). 20 nos 91.8

SITC of Jack Cat 6 Keystone UTP (Including Five year free maintenance with

105 guarantee) 50 nos 163.2

Supplying & erecting approved make LAN cable of following size in existing

106 pipe as per direction. [C] CAT - 6. for LAN points & for cctv points. 500 mtrs. 45.9

Providing & Erecting 6 core fibre optic SM 9/125um double sheath, CSTA,

107 Unitube, Outdoor cable (per m). 150 mtrs. 59.16

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections

as per site situation directed by Engineer In charge. (3) Two Pin/RJ-11

108 Telephone Socket. [B] For Two Gang. Cat III. 5 nos 202.98

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following

size complete to be erected on/in wall or ceiling erected with necessary

PVC fittings & Junction boxes fixed with adhesive solution & Clamps with

109 following dia of pipes, in approved manner as directed. (b) 25 mm. 200 mtrs. 32.64

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of

coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1)

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of

coupling, PVC bushes, Check-nuts etc. complete of following sizes. (2)

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following

size (a) with medium class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq.

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following

size (a) with medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq.

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling

with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (A) with medium class

114 Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm. 150 mtrs. 108.12

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling

with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size. (a) with medium class

115 Rigid PVC pipe and accessories (b) 2 wire 6 sq. mm. 50 mtrs. 141.78

Supply, Installation, Testing and Commissioning of suitable sweep, BEE

Star rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent

ferrite magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium

blades, 2 nos. canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W) minimum 6.85,

Air delivery minimum 215 CMM, 350 RPM,230v (tolerance as per IS : 374-

2019), THD < 10%, with remote unit for Speed Control and all remaining

accessories including safety pin, nut bolts, washers, temperature rise =

degree C (Max.), suitable for 140 to 285 Voltage and rectifier circuit with

surge, over current and overload protection , 50 Hz, Single phase AC

Supply, earthing etc. Complete as required. [ Make shall be approved by

116 Engineer in Charge] .(B)1200mm sweep(48") 20 nos. 2914.1

Supplying and erecting approved make double ball bearing oscillating type

Heavy duty bracket fan with Aluminium Blades A.C. 23OV. 50cy/s wall

mounted with height adjustment and rotary tilting device complete with

117 guard, wall bracket,mounting accessories as directed. A-450MM 40 mtrs. 4999

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe

down rod erected duly painted for fan complete with proper insulation

118 without leckage and earthing. 20 N0S. 109.14

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to

the RCC bars up to 50mm length each side and pierced through a 16 Gauge

M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with

119 necessary finishing. 20 nos. 109.14

Supplying & erecting single phase approved make industrial exhaust fan

suitable for medium duty ring mounted low noise operation suitable for

medium duty having following dia size and maximum speed in RPM

[E] 450 mm dia 1400 RPM.

Supplying & erecting approved make low noise decorative exhaust fan

having square frame ABS body with inbuilt lowers & square frame. 200mm

121 with 1350RPM Cat.II. 3 nos. 1720.7

122 Decorative call bell Ting-tong box type 250 volts complete erected. 2 nos. 69.36

Providing & erecting 240 V MCB double pole switch for motor & inductive

load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity. - use for AC control.

123 (A) 6 to 32 Amp. cat III. 8 nos. 302.94

Sheets steel powder coated enclosure suitable for incorporating One/Two

124 nos. MCB. - use for AC control. 5 nos. 178.5

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity

125 (a) 6 to 32 Amp. cat III. 2 nos. 601.8

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for (A) single phase incoming and horizontal

126 single phase outgoing (b) sheet steel double door (IP-43) (i)4 way 5 nos. 635.46

providing and erecting Miniature circuit breaker single pole 0.5A to 2A

system and having breaking capacity 10 KA to be erected in existing box.

127 confirming to IS 8828/1996 with ISI Mark 25 nos. 273.36

Providing & erecting 240 V MCB double pole switch for motor & inductive

load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

128 existing box having following capacity. (B) 40 Amp. cat III. 2 nos. 333.54

providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected

129 as directed(i) 25 Amps.DP. cat III. 4 nos. 1989

providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected

130 as directed(ii) 40Amps. DP . cat III. 2 nos. 2257.3

Providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on 3 phase and neutral 415V,50Hz. having

characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component for following Max. rating erected as

131 directed. (ii) 40Amps. FP. cat III. 1 nos. 2663.2

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve)

having 10KA breaking capacity & confirms to IS :8828 in existing box having

following capacity

(a) 6 to 32 Amp

132 Cat.III . 1 nos. 584.46

133 Half / One Module Blanking Plate of Standerd Size. 12 nos. 9.18

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for (A) single phase incoming and horizontal

134 single phase outgoing. (b) sheet steel double door (IP-43) (iii) 8 way. 1 nos. 1163.8

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for (B) single phase incoming and horizontal

135 single phase outgoing. (b) sheet steel double door (IP-43) . (iv) 12 way . 1 nos. 3912.7

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for (B) three phase incoming and single phase

horizontal type outgoing Per phase isolation type (PPI). (b) sheet steel

Providingdoor. (ii)6 way.

& erecting weather proof, dust & vermin proof, floor mounted 2 nos. 2942.7

front operated indoor type cubical panel board having necessary IP-42

protection & above as per requirements made from 14 SWG thick CRC M.S.

sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary supporting angles, flats including cutting,

bending, drilling, welding, riveting with internal partitions & cable alley as

per requirements & instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, with suitable size of inter connecting PVC

copper wire / copper-aluminium strips, rubber grommets, rib, bakelite

control fuses for measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber gasket, heavy duty end

terminal connections complete. The Panel shall be painted with epoxy

powder coating. (The rates excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams) The panel shall be

supplied with following approved manufacturers with following size.

137 (B) The standard companies switch gear shall be used and only 2 Sqm. 19580

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.

138 (b) One wire 1.50 sq. mm. 10 mtrs. 16.32

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.

139 (d) One wire 4.00 sq. mm. 20 mtrs. 35.7

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.

140 (e) One wire 6.00 sq. mm. 20 mtrs. 54.06

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.

141 (f) One wire 10.00 sq. mm. 20 mtrs. 88.74

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.

142 (g) One wire 16.00 sq. mm. 10 mtrs. 136.68

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically for control panel,

relays, power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.

143 (h) One wire 25.00 sq. mm. 6 mtrs. 227.46

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.housing.

144 ICS=100% of ICU only Cat III 1 nos. 16382

Approved make Earth fault Relay suitable to mount with inter connection

to moulded case circuit breaker having CT ratio & MCCB rating as following

along with shunt trip 220V AC. with all internal connections & complete

erected in existing M.S.housing.

Supplying & erecting approved make Four Pole 415V change over switch

interior for panel mounting with operating mechanism A.C.23 duty

confirming to IS for

146 Cat-lll 1 nos. 7867.3

Supplying and erecting triple pole & neutral 440V / 500V panel mounting

Copper Busbars with four equal Nos. of electrolyte bus having current

density not more than 1.6 Amp. / sq.mm (Rated current / cross section

area) duly wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each bar, erected in existing

cubical panel with necessary connections.

147 (B) Suitable for 200 Amp. capacity . 6 mtrs. 3234.4

Supplying and erecting approved make panel mounting type Digital

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected on

existing panel board with all connection, wiring etc .with manufacturers

148 calibration certificate. 3 nos. 1288.3

Supplying and erecting approved make panel mounting type Digital

Ammeter having 3 digits LED display, external CT operated, calibrated for

0 to 1000 Amps suitable to operate on 500 Volt AC , erected on existing

panel board with all connection, wiring etc .with manufacturers calibration

149 certificate. 2 nos. 1573.9

Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase

150 AC Supply 500 V on existing panel board with necessary connections. 4 nos. 320.28

Supplying and erecting approved make suitable panel indicator LED type

151 lamp, lens cover, complete erected with necessary connections. 5 nos. 43.86

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

152 Cat.III 10 Ea. 113.22

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing 16 G.M.S. housing.

153 ICS=100% of ICU only Cat III 3 Ea. 6234.2

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia

of 40 mm having 200-250 Micron galvanising, connection terminal dia of

14 mm with constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following type of

applications. [B] For Electrical installation up to 11 KV located in other

than normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr

154 -Back filling Compound :1 no. Bag of 25 Kg. 6 nos. 7165.5

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or

approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe

dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm

having 200-250 Micron galvanising, connection terminal dia of 14 mm

with constant ohmic value surrounded by highly conductive compound

with high charge dissipation suitable for following type of applications

[C] For Electrical Installation covering Transformer Neutrals, Lightning

arrester Earthing, A.C.Plant & Sensitive Computer System(like

Automation, SCADA)i.e. independent Earthing located in other than

normal soil i.e. Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

155 -Back filling Compound :2 nos Bags of 25 Kg. 2 nos. 10699

156 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 10 kg. 802.74

Providing and erecting required size HOT deep Galvanised iron strip for

earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using

157 proper clamp. 10 kg. 78.54

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables(D) 3 1/2 core 70 Sq.

mm ( 35 Sq. mm 1/2 core) (Main cable from transformer to meter panel.

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable

159 KV grade to be erected as directed of following size. (N) 4 core 16 Sq. mm 50 mtrs. 731.34

Solder less crimping type Copper lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

160 manner. (C) 16 Sq.mm. 8 nos. 12.24

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or

in existing trench / pipe at road crossing or floor of following size of

cables. (C) 4 core 6 Sq. mm Cu. Conductor YWY cable. (Main feeder Panel

161 to PDB.). 80 mtrs. 513.06

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand /

Solid Copper conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe at road crossing or floor of following

size of cables. (A) 4 core 2.5 Sq. mm . (Main feeder Panel to Streetlight

162 fixtures & 3 phase machines,motor connection ). 300 mtrs. 272.34

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv

grade ISI marked copper wires of following size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed. - streetlight pole box to fixture

Providing and, fixing heavy duty flange type brass cable gland with rubber

ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (C) 3 & 1/2 core 70 Sq. mm

164 . (Main cable from transformer to meter panel. ). 3 nos. 104.04

Providing and, fixing heavy duty flange type brass cable gland with rubber

ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (B) 2 to 4 core 6 Sq. mm.

165 (Main feeder Panel to LDB, PDB.). 15 nos. 38.76

Solder less crimping type Copper lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

166 manner. (A) 1.5/2.5 to 6 Sq.mm. (Main feeder Panel to LDB, PDB.). 120 nos. 8.16

Solderless crimping type Copper lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

167 manner. (B) 10 Sq.mm. 6 nos. 10.2

Solderless crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated nut bolts in an

168 approved manner. (E) 70 Sq.mm. 8 nos. 25.5

Providing & laying approved make Double walled corrugated pipes (DWC)

of polyethylene(conforming to IS 14930 II )with necessary connecting

accessories of same material at required depth for laying of cable. below

ground /road surface for enclosing cable and back filling the same to make

169 ground as per original.(A)50 mm dia. 400 mtrs. 63.24

Providing & laying approved make Double walled corrugated pipes (DWC)

of polyethylene(conforming to IS 14930 II )with necessary connecting

accessories of same material at required depth for laying of cable. below

ground /road surface for enclosing cable and back filling the same to make

170 ground as per original.(D)120 mm dia. 100 mtrs. 138.72

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.9, THD

< 15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 % ( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.). (A) Tube Light with integral driver.

171 (iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet. cat III. 40 nos. 298.86

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.).

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips complete.IP20. (i) 5-9

172 watts,Surge-2 KV. CATIII 20 nos. 222.36

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.95,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)(i) 5-

173 10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet 10 nos. 167.28

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.).

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips complete.IP20. (iv) 22-24 watts,

174 Surge-2 KV. 60 nos. 766.02

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminium housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses with

company mark/name engraved or embossed 160 to 270 V,Power Factor

more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.). (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC

175 line supply with over-voltage protection. (iii) above 24 to 36 watts. Cat - III. 20 nos. 2223.6

Providing street light pole bracket consisting of Light Class MS.pipe of

cms. outside dia. complete with suitable M.S. sleeve tubing of approximate

45 cms. and length suitable for 76.5 mm / 80mm. / require size pole top

having sufficient fastners for fixing the brackets and having spread of 1 mtr.

length with suitable rise as per site condition & suitable welded stiffener

reducer and nipple with check nut complete painted with one coat of Red

oxide / PU base primer and two coats of Aluminium / PU paint. paint with

following nos of arms.

176 [A] Single Arm bracket 1 Mtr. 20 nos. 567.12

Supplying and erecting approved make Octagonal pole made from HR

sheet steel. The pole should be made as per IS. and shall be coated with

hot dip galvanizing as per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting,

stud type terminal and arrangement for cable termination to be erected

With Suitable foundation (Included) as per details given by manufacturer

considering site requirement.

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm long J-

177 Bolt.Approx Pole weight 59 kg. 20 nos. 8273.2

Supplying and erecting B class Galvanized iron pipe having smooth finished

bore of the pipe on both ends erected nuts and bolts along the pole / wall

shaping the pipe as per site requirement. Pipe dia as following.

Supplying & erecting approved make IP 55 grade Company fabricated

Timer Panel of following capacity for switch On-Off street lights on time

scheduling basis made from 16G CRCA sheet duly epoxy power painted

inside and outside with hinged doors and locking arrangement consisting of

suitable size of 4 Pole MCB and 4 pole contactor (cat-III)with analog time

switch, auto manual switch of same make and suitable input and output

Bakelite terminals and with door earthing approved by Engineer in charge.

Supplying & erecting approved make SMC press moulded composite FRP.

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as per

requirement having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable clamps& earth bolt

180 of following size of box. (C)150mm x 125mm x 100mm [deep]. 20 nos. 481.44

Making trench in soft soil of suitable width of 90 cm deep for laying cable

or locating the fault all over the run and back filling the same and making

181 the surface as normal ground. 298 mtrs. 46.92

Supplying stand first AID box with antiseptic cream, medicine for use on

wounds due burn, crepe bandage, gauge bandage, medicated ready to use

bandage (Band-aid) adhesive tape for medicinal user, Scissors, anti-septic

solution (Savlon or similar) etc. (All above contents shall be of standard

182 makes) 2 nos. 302.94

Supplying and erecting floor mounting stand for keeping four nos. of FIRE

buckets comprising 1500 mm in length, 900 mm height frame made out of

30mm X30 mm X 4 mm angle iron with cross supports for legs, welded with

4 hooks and duly painted with one coat of red lead and two coats of

183 approved enamelled silver paint. 2 nos. 951.66

Providing and fixing printed instruction chart both in English and Gujarati

and duly framed with front glasses, for treatment of person suffering from

184 Electric shock with minimum 50" diagonally size. 2 nos. 131.58

Providing & erecting open well horizontal mono block pump set with cast

iron body, complete for three phase submersible motor having[C] For 3 HP

3 phase open well horizontal mono block pump set suitable for 85 LPM to

270 LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe

185 Cat. III 1 nos. 15863

Tender Value In Words

I/We am/are willing to carry out the work at…% above/below per cent (Should be writen in figures and words) of

the estimated rate mentioned above. Amount of my /our tender works out as

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Deduct………% below

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017