Renovation of old godown, reconstruction of compound wall, providing scooter shed and drain at State Warehouse Kayamkulam in Alappuzha District.

Amount

15.31 Dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead

15.14.1 Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead:Of sectional area 40 square centimetres and above

15.41 Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

15.3 Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.12.1 Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

15.7.3 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In lime mortar

15.9.2 Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

50.6.1.5 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

od139053/2021_2022 Brick work with departmental country burnt bricks in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 (1 cement : 6 coarse sand)(from floor 2 level up to floor 5 level) as per direction of Engineer in charge

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

10.6.1 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths,interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 0.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 Providing and fixing ball bearing for rolling shutters.

od91194/2021_2022 Supplying and fixing steel glazed top windows of size 1.20 x 0.6m outside with z section for outer frame and shutter frame conforming to IS 1038, with 20 x 20 x 20 x 3mm z section for outer frame and 45 x 20 x 20 x 3mm J section for intermediate vertical of 1 No, 4 Nos of 10mm square rods welded horizontally to the outer frame, fixing proper box hinges to the shutter –frame of size 20 x 20 x 20 x 3mm z section for the double leaf shutter 4mm thick plain glass fixed with 12.5 x 12.5 x 1mm Aluminium L angle bolted with 5mm G.I. bolts and nuts 15 cm c/c fixing welded mesh 25 x 25mm square 12 guage with 20 x 5mm M.S. flat frame alround and intermediate vertical bolted to out frame with 5mm/M.S. bolts and nuts 25cm c/c, 2 Nos of flat iron clamps 200 x 20 x 5mm size welded on each side of outer frame to be fixed with cement concrete ( cement concrete block will be paid separately) standard locking arrangements, applying one coat metal primer including cost and conveyance of all materials required and all labour charges etc. complete and as per direction of Engineer in charge

od91195/2021_2022 Supplying and fixing steel panelled bottom windows of size 1.20 x 0.60m outside with Z section for outer frame and shutter frame conforming to IS 1038, with 20 x 20 x 20 x 3mm z section for outer frame and 45 x 20 x 20x 3mm J section for intermediate vertical of 1 No., 4 Nos of 10 mm square rods welded horizontally to the outer frame and shutter frame of size 20 x 20 x 20 x 3mm z section, fixing proper box hinges to the shutter frame, for the double leaf shutter 20 guage plain M.S. sheet for paneling welding with outer frame, fixing welded mesh 25 x25mm square 12 guage and 20 x 5mm M.S. flat frame alround and intermediate vertical bolted to outer frame with 5mm bolts and nuts 25cm c/c.2 Nos.of flat iron clamp 200 x 20 x 5mm size welded on each side of outer frame to be fixed with cement concrete ( cement concrete block will be paid separately) standard locking arrangements, applying a one coat metal primer including cost and conveyance of all materials required and all labour charges etc. complete and as per direction of Engineer in charge

od91196/2021_2022 Engaging carpenters for reapir wooden works as per direction of Engineer in charge

od91197/2021_2022 Engaging man coolie for repair and cleaning works as per direction of Engineer in charge

od91198/2021_2022 Providing and laying cement concrete 1:6:12, using 40mm broken stone for flooring in panels not exceeding 20m2 in area including charges for watering, curing, consolidating, paneling including cost and conveyance of all materials required etc complete and as per direction of Engineer in charge

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4(1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

od91191/2021_2022 Providing and fixing Galvalume sheets ( Supply of pre painted Alu- Zinc alloy coated steel sheets (55% Aluminium, 43% Zinc, 1.6% Silicons)0.50mm thick). Sheet should have protective guard film of 25 micrones minimum to avoid scartches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in charge.The sheet shall be fixed using self drilling/self tapping screws of size (5.5 x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, , including providing necessary overlap not less than 150mm at end 1 1/2 corrugation at sideexcluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.as per direction from Engineer in charge.

od139769/2021_2022 Providing ridges or hips width 60cm overall width plain Galvalume sheet fixed with polymer coat , including hooks, bolts and nuts 8 mm dia G.limpet and bitumen washers complete 0.5mm thick , coating not less than 275 gm/m2 as per direction of Engineer in charge

od91200/2021_2022 Providing bitumen compound covering to G.I. bolts over roof using 0.45 Kg of bitumen compound per 10m2 area including cost and conveyance of all materials required etc. complete and as per direction of Engineer in charge

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.29.1 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

od139895/2021_2022 White washing with White cement to give an even shade:New work (one or more coats)

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil

4.1.11 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more

od91201/2021_2022 Providing 12mm dia L bolts for fixing the wooden fender to the bottom ledge with M.S. rods 45 cm long including charges for supplying nuts, threading, bending and pacing in position as per instruction during execution including cost and conveyance of all materials etc complete and as per direction of Engineer in charge

od91202/2021_2022 Supplying and fixing in position anjili wooden fender of size 15 x 10 cm plained and lap jointed to the bottom ledge including charges for necessary overlap providing holes for bolts fixed in ledge as per instruction cost and conveyance of all materials required etc. complete except L bolts and as per direction of Engineer in charge

11.36 Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

50.6.2.1 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

od91192/2021_2022 Supplying and fixing PVC door of size 0.8 x 2.10 m including cost and conveyance of all materials required , fixing in postion etc. complete as per instruction during execution as per direction of Engineer in charge

17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 litre white P.V.C. automatic flushing cistern

17.7.3 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

50.18.7.4.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

50.18.7.2.1 Providing and fixing PVC pipes, fittings including fixing the pipe with claps at 1.00 metre spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20 mm dia 12Kgf/cm2 - Internal work - Exposed on wall

50.18.9.9.2 Providing and fixing PVC pipes includes joints of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in CHarge. 110 mm dia 4 Kg/cm2

50.18.9.22.3 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.18.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.21.7 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

od91613/2021_2022 Supplying and and fixing PVC tap of required size including all labour and materials used etc complete as per direction

5.1.3 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

16.18.1 Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for serarately) :-Payment to be made per metre cost of total length of barbed wire used.With G.I. barbed wire

16.19 Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

13.63.1 Painting with aluminium paint of approved brand and manufacture to give an even shade.Two or more coats on new work

13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

16.78.2 Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBRValue-25

2.32 Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared

QUBE CONSTRUCTION

V. SOMARAJAN

Thomas Kurian

Varghese Kurian