Renovation and Interior Fit-Out Works of SIDBI Branch Office, Naroda

15 Grand Total 8,646,901.66

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

1 FLOORING WORKS

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with

15 micron anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed to

conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and

Supplying and fixing of 3mm Luxury vinyl flooring Top layer of approved

design & Pattern as per architects approval & Instructions

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of

Type 6 nylon loop pile carpet tiles/Plank. The carpet shall have sufficient

gauge (1/10 ~ 1/12) with sufficient stitches (10~13) per inch. The carpet shall

1.03 MR be solution dyed fibre content or with injection printing technology. The 20.00 sq m 1650.00 33,000.00

carpet shall have the pile height ranging from (2.0 ~ 3.0) mm with

average density higher than 4500 Oz/ cubic yard. The total thickness of

the carpet tile shall also range from (5.5 ~ 6.0) mm.

LAMINATED WOODEN FLOORING Providing and laying 8.3mm thick AC5

grade laminate wooden flooring having good castor chair and furniture

resistance strength. Plank dimension to be 1215x195x8.3mm with valinge

clock locking system and wax coating for better sound resistance. Impact

and abrasion resistance to be of high grade having class EN 13329. The

flooring shall be laid with 2mm thick underlay and PVC sheet and prevent

against moisture and foot taping sound. The item also includes the skirting

1.04 MR and any other profiles required for proper installation.or its equivalent 20.00 sq m 1770.00 35,400.00

specifications or as per the selection of client and items shall be complete in

all respects. or its equivalent specifications/ size as per the site requirement or

as per the selection of client and items shall be complete in all respects.

2 FALSE CEILING WORKS

Digitally signed by AMIT

S NO AMOUNT AMOUNT

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height

including providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of

size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at

1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm

with tapered flanges of 26 mm each having lips of 10.5 mm, at 450

mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230

mm long G.I. wire at every junction, including fixing perimeter channels 0.5

mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450

mm centre, with 25mm long dry wall screws @ 230 mm interval, including

fixing of gypsum board to ceiling section and perimeter channel with the

help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing

and finishing to a flush finish of tapered and square edges of the board

with recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all

complete as per drawings, specification and direction of the Engineer in

Charge but excluding the cost of painting with

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part

I) :2011 (Board with BIS certification marks)

Providing & fixing of Silhoutee Frame ceiling tile in size 600x600x15mm having

noise reduction co-efficient of 0.7, Density of 100 kg / m3, and Humidity

resistance of 95% to be laid on exposed grid system with white wrap

comprising main runner 3.00 mm x 24mm web height cross tee 1.2 mtrs x 24

mm web height and 0.6 mtrs x 24 mm web height. The wall angle shall be 3.0

Digitally signed by AMIT

S NO AMOUNT AMOUNT

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

3 PARTITIONS AND WALL CLADDING - -

WALL PANELING :-Providing and fixing Paneling upto ceiling height

consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling

channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed

to the floor and ceiling at the spacing of 610 mm centre to centre with dash

fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or

metal screws with nylon plugs and the studs 48 mm wide having one

flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically

within flanges of floor and ceiling channel and placed at a spacing of 610

mm centre to centre by 6 mm dia bolts and nuts, including fixing of

studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to

centre, and fixing of boards to both side of frame work by 25 mm long dry

wall screws on studs, floor and ceiling channels at the spacing of 300 mm

centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width

(0.9 mm thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal flat

head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25

mm x 25 mm x 0.5 mm), joint finisher as per manufacture's specification and

direction of engineer in charge all complete.(Cost of Aluminium framing

600X600mm Paid saperately)

Paneling with 12 mm thick HDHMR board to IS: 5509 62.00 sq m 2,414.28 149685.42

Digitally signed by AMIT

S NO AMOUNT AMOUNT

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

WALL PARTITION-Providing and fixing partition upto ceiling height

consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling

channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed

to the floor and ceiling at the spacing of 610 mm centre to centre with dash

fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or

metal screws with nylon plugs and the studs 48 mm wide having one

flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically

within flanges of floor and ceiling channel and placed at a spacing of 610

mm centre to centre by 6 mm dia bolts and nuts, including fixing of

studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to

centre, and fixing of boards to both side of frame work by 25 mm long dry

wall screws on studs, floor and ceiling channels at the spacing of 300 mm

centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width

(0.9 mm thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal flat

head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25

mm x 25 mm x 0.5 mm), joint finisher as per manufacture's specification and

direction of engineer in charge all complete.(Cost of Aluminium framing

600X600mm Paid saperately)

Both side 12 mm thick HDHMR board to IS: 5509 100.00 sq m 3450.00 345000

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick

MDF, on an existing Plywood surface.

Providing and fixing 12mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top &

bottom pivot & double acting hydraulic floor spring type fixing arrangement

and making necessary holes etc. for fixing required door fittings, all complete

as per direction of Engineer in charge (Door handle, lock and stopper etc. to

be paid separately)

Digitally signed by AMIT

S NO AMOUNT AMOUNT

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or with

9.1 dash fasteners of required dia & length (hold fast lugs or dash fastener - -

shall be paid for separately).

9.1.1 Second class teak wood 0.3 cum 142949.7 42884.91

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock

wool conforming to IS: 8183, having density 48 kg/m3,50 mm

thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel

12.62 plug & washers and held and in position by criss cossing GI wire etc. 125 sq m 322.50 40312.50

complete as per directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part

I) non-decorative type, core of block board construction with frame of 1st

9.21 class hard wood and well matched commercial 3 ply veneering with vertical -

grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary

Providing and fixing aluminium extruded section body tubular type

universal HS 3000 Slimline Concealed Door Closer (having brand logo with ISi,

IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and door

MR widthfrom 701 mm to 1000 mm), with double speed adjustment with 4 each 2,450.00 9,800.00

necessary accessories and screws etc. complete

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI

9.97 marked, anodised (anodic AC 10 as per IS : 1868 ), transparent or dyed to -

required colour or shade, complete:

9.82 DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor

door stopper with necessary screws, etc. complete. 4 EACH 121.65 486.60

MR MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular

Handle TH 123 with Roses & Escutcheon in SS packaged with Mortice

lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all 4 EACH 3,250.01 13,000.04

Digitally signed by AMIT

S NO AMOUNT AMOUNT

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

MR Providing and fixing 600 mmx25 mm H Type handle for Doors approved

make and designs as per engineer in charge 4 EACH 3,250.00 13,000.00

MR Providing and fixing minimium 100 kg capacity flooor spring for Doors

approved make and designs as per engineer in charge 4 EACH 8,500.00 34,000.00

MR Providing and fixing Glass door lock approved make and designs as per

engineer in charge 4 EACH 1,680.00 6,720.00

Providing and applying plaster of paris putty of 2 mm thickness over

13.26 plastered surface to prepare the surface even and smooth complete. 375 sq m 262.70 98512.50

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50 grams/ litre

13.83 of approved brand and manufacture, including applying additional coats -

wherever required to achieve even shade and colour.

13.83.2 Two coats

Applying priming coats with primer of approved brand and manufacture,

13.85 having low VOC (Volatile Organic Compound ) content. -

13.85.1 With ready mixed pink or grey primer on wood work (hard and soft wood)

having VOC content less than 50 grams/ litre 300 sq m 70.35 21105.00

Digitally signed by AMIT

S NO AMOUNT AMOUNT

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

BLINDS Providing & supplying of Window Blinds as per the approved

sample in required shade and style consisting, of ZEBRA BLINDS comprising of

optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight

460-480G weight per sq m, Thickness 0.67 mm, Yarn count 18- 19/cm,

having fire resistance standard – NFPA 701-89 small testing ISO- 5659-2

.Thetear resistance should be complying to ISO4674 & breaking resistance –

ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe

installation, moulded plastic with steel spring support and inserted into the

tube end. It shall be driven by a ball chain pulley with ball chain and can be

positioned at right side or left hand side of the Shade. The Shade when

lowering or raising, shall be automatically locked in position upon release of

the ball chain by means of a built in friction lock.Universal clutch for left and

right hand operation.Chain Gear Ratio of 1.75:1. The END PLUG shall be

M.R. molded of plastic witha steel location pin.The plug shall be inserted into the 50 sq m 1,650.00 82500

tube end.(Opposite to the Drive Unit) for ease of installation. The SUPPORT

BRACKETS shall be of coated steel & provided with covers and used in right

hand or left hand positions differentiated by the acceptance of the of the

rectangular drive unit support or the round idler plug pin.Can beinstalled (a)

On Face (b) Ceiling Mount (c) On Frame

(d) in Recess. The Bracket should be protruding outside maximum of

80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal

diameter & skin thickness of 1mm and shall incorporate a key way integral

with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat

Bottom made up of powder coated steel. The BALL CHAIN shall be 2mm

diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on

6mm pitch to form an endless ball chain. It is used for raising or

M.R. FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass

surface as approval of the Architect. (Only film surface area shall be 50 sq m 1,650.00 82500

measured and paid).

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm

Laminate of matching, Shutters to be fixed to a frame. Rigidly fixed on both

sides and top finshed in laminate. No internal carcass required. All Hinges of

hettich or equivalent. Internal Surface of the shutter in balancing white

MR laminate. All shutters to be provided with Stainless steel louvers at the top 5 sq m 11,500.00 57500

and bottom of the shutter as per the site requirements and instrcution of

the Engineer In charge.

Digitally signed by AMIT

S NO AMOUNT AMOUNT

DSR DSR/MR DESCRIPTION QUANTITY UNIT RATE

2023 DSR RATE NON DSR

Providing & fixing Sidbi Signages & Logo & Sidbi Enviremoent Theme as per

MR Direction of Engineer in Charge 20 Sft 2450.00 49000

Providing & fixing Sidbi Sign Glow Board For Exterior Acrylic Base Embeded

MR Letter as per design 70 Sft 1650.00 115500

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height

consisting of G.I. frame and required board, including providing and

fixing of frame work made of special section power pressed/ roll form

G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive),

consisting of floor and ceiling channel 50mm wide having equal flanges

of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of

610 mm centre to centre with dash fastener of 12.5 mm dia meter 50

mm length or suitable anchor fastener or metal screws with nylon plugs

9.105 and the studs 48 mm wide having one flange of 34 mm and other

flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor

and ceiling channel and placed at a spacing of 610 mm centre to centre

by 6 mm dia bolts and nuts, including fixing of studs along both ends of

partition fixed flush to wall with suitable anchor fastener or metal

screws with nylon plugs at spacing of 450 mm centre to centre, and

fixing of boards to both side of frame work by 25 mm long dry wall

screws on studs, floor and ceiling channels at the spacing of 300 mm centre

The boards are to be fixed to the frame work with joints staggered to

avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm

thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners

(25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer

suitable for board as per manufacture's specification and direction of

engineer in charge all complete.

9.105.1 75 mm overall thickness partition with 12.5 mm thick double skin fire rated

Glass Reinforced Gypsum (GRG) 50 sq m 2,131.10 106555

plaster board conforming to IS: 2095:

Add labour cess @0.973 as per CPWD circular 945,946.13

Add CPWD cost index @103 on DSR civil 2023 974,324.52

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

1.10 Wiring for light point/ fan point/ exhaust fan point/ call

bell point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed medium class

PVC conduit, with modular switch, modular plate, suitable GI

A.1 box and earthing the point with 1.5 sq.mm. FRLS PVC

insulated copper conductor single core cable etc as required.

1.55 Wiring for group controlled (looped) light point/ fan point/call

bell point (without independent switch etc.) with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in

surface / recessed PVC conduit, and earthing the point with

A.2 1.5 sq.mm. FRLS PVC insulated copper conductor single core

cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed

medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC

insulated copper conductor single core cable for loop earthing

1.24 Supplying and fixing following modular switch/ socket on the

existing modular plate & switch box including connections but

excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 32 122.00 3904.00

1.24.5 6 pin 15/16 amp socket outlet Each 32 197.00 6304.00

A.5 1.26 Supplying and fixing modular blanking plate on the existing Each 200.00

modular plate & switch box excluding modular plate as 5 40.00

Digitally signed by AMIT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

1.27 Supplying and fixing following size/module, GI box along

with Modular base & cover plate on existing modular metal boxes

etc. as required.

B SUBMAIN AND CONTROL WIRING

1.14 Wiring for circuit/ submain wiring alongwith earth wire with

the following sizes of FR PVC insulated copper conductor,

single core cable in surface/ recessed medium class PVC conduit

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 280 275.00 77000.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 439.00 21950.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 35 1365.00 47775.00

9.1 Supplying and making end termination with brass

compression gland and aluminium lugs for following size of

PVC insulated and PVC sheathed / XLPE aluminium

conductor cable of 1.1 KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to

I.S.7098/1554AluminiumConductor Cables:

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated

C.2 Aluminium conductor armoured cable of 1.1 KV grade

conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI

Digitally signed by AMIT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

(b) 3.5 C x 95 Sqmm XLPE cable RM 30 864.00 25920.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 30 378.00 11340.00

C.3 MR Supply of following sizes of copper cables -PVC sheathed

PVC/XLPE insulated Copper conductor armoured cable of 1.1

KV grade conforming to IS:7098 part-1 / IS:1554 part-1

respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 50 1446.00 72300.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 35 2253.00 78855.00

D.1 2.11 Supplying and fixing single pole blanking plate in the existing MCB Each 1300.00

DB complete etc. as required. 100 13.00

D.2 Supplying and fixing 5 amps to 32 amps rating, 240/415

volts, "C" curve, miniature circuit breaker suitable for inductive

load of following poles in the existing MCB DB complete

with connections,

testing and commissioning etc. as required.

2.10.1 Single pole Each 40 256.00 10240.00

2.13 Supplying and fixing following rating, four pole, 415 volts,

isolator in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

D.4 2.4 Supplying and fixing following way, horizontal type three

pole and neutral, sheet steel, MCB distribution board, 415

V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But

without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 2 9081.00 18162.00

Digitally signed by AMIT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm

solid copper conductor PE insulated, shielded with fine

tinned copper braid and protected with PVC sheath

in the exisitng

surface/recessed steel/ PVC conduit as required

E.12 Supplying and fixing of following sizes medium class PVC conduit

aong with accessories in surface/ recess including cutting the wall

1.21 and making good the same incase of recessed conduit as

4.1 Supplying and Installation of following size perforated of

painting with powder coating M.S. cable trays of perforation

of not more than 17.5% in convinient sections, joined

E.13 with connectors suspended from the cieling with MS suspenders

including bolts and nuts painting suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 15 1137.00 17055.00

Earthing with copper earth plate 600 mm X 600 mm X 3

mm thick including accessories, and providing masonry

enclosure with cover plate having locking arrangement and

watering pipe of 2.7 metre long etc. with charcoal/ coke and

salt as required.

F.2 5.14 Providing and fixing 25 mm X 5 mm copper strip onsurface or in

recess for connections etc. as required. MTR 15 1162.00 17430.00

F.3 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or

in recess for connections etc. as MTR 16 244.00 3904.00

Digitally signed by AMIT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

S DSR DESCRIPTION UNIT TOTAL AMOUNT TOTAL AMOUNT

2022 DSR (INR) NON-DSR (INR)

Supply, Installation, Testing and Commissiong of 10 KVA True Online Double

Conversion UPS 3Phase Input - 3Phase Output in IGBT Based Rectifier and

IGBT Based Inverter Batteries:12 V, SMF Amararaja/Exide with minimum VAH

capacity of 15600 suitable for 30 minutes backup with each ups Along with

Accessories Rack, Interlinks, SFU, Parallel Kit, DC Cable Upto 5 Meters

complete in all respect as per the directions of the engineer in charge. UPS

should have availability of Input /Output isolator, Inbuilt manual bypass along Nos 1 365000.00 365000.00

with phase sequence corrector. UPS Efficiency shall not be less than 94% from

25% to 100% Load

Total of Electrical items 605352.00 571577.00

Add GST factor @1.0633 on DSR items 643670.7816

Add CPWD labour cess factor @0.973 626291.6705

Total Amount 626291.6705 571577.00

Total Amount 626291.6705 571577.00

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

Supply, Installation, Testing & Commissioning of Modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units

suitable for cooling/heating having 100% hermetically sealed inverter type

twin Rotary/Scroll Compressor(s),minimum two compressors (with

individual separate PCB) for above 14HP modules, microprocessor

based Controller, top discharge type condensing unit(s), with R-410-A

Refrigerant or equivalent, vibration Isolators with suitable foundation etc.

complete as required. To have better efficiency condenser fan shall

be capable to operate at different speed with respect to load. The

unit shall deliver the rated capacity and in confirmation as per IS

18728:2024 and CPWD Specifications and work even at 50°C ambient

temperature without tripping. The system shall be able to deliver 100% of

7.3 the rated capacity upto 39 Degree Celcius.The unit shall be suitable to

work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS

compatible. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The condenser should be coated with a

hydrophilic film to prevent water accumulation on the surface of the heat

exchanger, enhance water dispersion, and reduce the risk of

degradation, thereby improving overall performance and durability. The

Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per

Energy Conservation and Sustainable Building Code (ECSBC) 2024 as

below and complete as per CPWD specification, connections, inter

connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity >

<70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)

2.0 INDOOR UNIT

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

Supply, Installation, Testing and Commissioning of following minimum

capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre- filter, fan section with low noise fan /

dynamically balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration Isolation, Corded remote control etc.,

suitable for operation on single phase 230 V ± 10%, 50Hz AC supply,

complete, as required. The Indoor units must shut down upon receiving a

singal from the BMS System/Fire Signals. The system shall be capable to

adjust air flow as per room requirement in auto mode. The cooling

capacity of indoor unit will be at air inlet conditions of 27 Degree C DB

and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum

capacity High wall type Indoor unit equipped with and comfort washable

synthetic media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX copper coil,

electronic expansion valve, outer cabinet, cord less remote control, drain pan,

7.8 necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single

phase AC supply, complete as required. The Indoor units must shut down upon

receiving a singal from the BMS System/Fire Singnals. The system shall be

capable to adjust air flow as per room requirement automatically. The

cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C

DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation

and Nitrogen testing of following nominal sizes of soft/hard drawn

copper refrigerant piping for VRV/VRF system, complete with fittings,

with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular insulation/with

Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19

mm thick insulation as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required :

3.2 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 40.00 346.00 13,840.00

3.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 25.00 615.00 15,375.00

3.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 15.00 739.00 11,085.00

3.8 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 30.00 1,157.00 34,710.00

3.10 7.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 30.00 1,286.00 38,580.00

3.14 7.13.2 Outdoor Multi Units Each 1 8098 8,098.00

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe ,complete

with fittings, supports,U trap arrangement,Clean Plug with 6mm nitrile

insulation and accessories as per specifications, drawings.

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq.

mm copper in suitable conduits between indoor and outdoor unit.

6 MR Supply & Fixing IP55 Base Outdoor MCB Box with in 1 Nos 65 amp RCCB Nos 1 14650 14,650.00

Supply and Fixing MS Base Frame for VRV Outdoor Stand as per requirement of

Add GST factor @1.0633 on DSR items 1129439.387

Add CPWD labour cess factor @0.973 1098944.523

Total Amount 1098944.523 87350.00

Total Amount 1098944.523 87350.00

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate DSR Amount NDSR Amount

A. UTP Components for Data

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper

conductors for Connectivity of Hub room to End Point.High Speed

Gigabit Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH

Supply , Installtion , Testing and Comissioning of I/O port for CAT6

4 MR cable termination at Rack Side. Keystone Unshielded Outlet, Nos. 50 359.00 17950

Supply , Installtion , Testing and Comissioning of I/O port for CAT6

5 MR cable termination at Rack Side end Redantant . Keystone Nos. 50 359.00 17950

Unshielded Outlet, 180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of CAT6 patch cord

2 Mtr (7 feet) for information outlet (I/O) to end user Redantant

device connectivity.High Speed Gigabit 24AWG U/UTP Patch

Cord Yellow, LSZH, C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of CAT6 patch cord

2 Mtr (7 feet) for information outlet (I/O) to Rack End Redantant

device connectivity.High Speed Gigabit 24AWG U/UTP Patch

Cord Yellow, LSZH, C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of 24 port Loaded

11 MR Angled Staggred Jack Panel for CAT6 cable termination at rack Nos. 4 6500.00 26000

end. Data Active Redandant

SITC of 04 core OM3 Multimode fiber orange color 50/125,

minimum bending radius 15x OD

13 MR SITC of 24U Rack Each 1 34,500.00 34500

Supply instllation testing and commissioning of Access Switch of 24 x 1G

POE+, 4 x SFP+ , 370W PoE, Switching Capacity of switch is of 176 Gbps

14 MR having Forwarding performance (64-byte packet size): 130 Mpps, Secure Shell

(SSH), as per approved Brand

B 200 Pair MDF Box

1 MR 200 Pair MDF Box with mounting Frame Nos. 1 11666.00 11666

Digitally signed by AMIT

S NO Description UOM Qty Rate DSR Amount NDSR Amount

2 MR 10 Pair Krone Module Nos. 5 900.00 4500

3 MR 25 Pair Riser Cable Mtr. 25 750.00 18750

GRAND TOTAL (A+B) 136800.00 350274.33

GRAND TOTAL (A+B) 136800.00 350274.33

Add GST factor @1.0633 on DSR items 145459.44

Add CPWD labour cess factor @0.973 141532.0351

Total Amount 141532.0351 350274.33

Total Amount 141532.0351 350274.33

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S TOTAL TOTAL

2022/ DESCRIPTION QTY UNIT RATE

No AMOUNT AMOUNT

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS

3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts,

18.7 gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and

1 painting with two or more coats of synthetic enamel paint of required shade complete

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of

18.21 rating 68 degree centigrade

2 with required accessories :

18.21.1 Pendant type 20 Each 522.00 10440.00

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless

steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI

18.25 test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler

head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center

bracket, stockbar of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all accessories

as per manufacturer's specifications.

a) MR CO2 gas nozzle type - 9 Litre capacity (IS:15683). 1 NOS 12059.40 12059.40

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). 1 NOS 2740.00 2740.00

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683). 1 NOS 4437 4437.00

Add GST factor @1.0633 on DSR items 134129.9785

Add CPWD labour cess factor @0.973 130508.4691

Total Amount 130508.4691 19236.40

Total Amount 130508.4691 19236.40

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CCTV

DESCRIPTION UNIT Qty RATE

Supply, Installation, Testing & Commissioning of 2MP IR IP H.265 Vandal Proof

Dome camera with 2.8 to 12mm Motorised Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise

1 MR Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple streams,3-Axis, Nos 8 4650.00 37200.00

IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with

IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection

Supply, installation testing and commissioning of Network Video recorder Linux

based to manage and control all the cameras from control room. Software shall

2 MR support maximum 16 channel with joystick controller. 256Mbps Bit Rate Input Nos 1 34500.00 34500.00

Max(up to 32-ch IP video), 2 SATA Interfaces, alarm I/O: 16/4, 1.5U case,19" with

1x4TB i.e. 4TB HDD inside

Supply, Installation, Testing & Commissioning of 55" Flat Screen HD led (24X7)

with Interfaces include HDMI, DVI, D-sub, Component and Composite input

4 MR as well as RS-232C and RJ45 for extensive connectivity, remote control and Nos. 1 44500.00 44500.00

wall mount unit / floor stand complete with making connections etc

complete as reqd.

5 MR SITC of HDMI cables 10 meters M2M etc all compelte. Nos 1 3500.00 3500.00

Total : A - CCTV 119700.00

Digitally signed by AMIT

S.NO. DESCRIPTION Qty UNIT RATE DSR AMOUNT

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of

(ii) M.R FIRE PANEL upto 2 zone complete as required. 1.00 No. 14500.00 14500

Supplying, installation, testing & commissioning of smoke

detector with built in LED and Mounting base complete

c) 17.1.2 withb all Connections etc. as required. 30.00 No. 1153.00 34590.00

Supplying, installation, testing & commissioning of

manual call boxes of MS construction in Surface/Recess

with Stainless Steel chain & hammer Assembly complete

with glass and push button etc. as Required.

Supplying, installation, testing & commissioning of

response indicator on surface/recessed MS Box having

d) 17.1.5 two LED, metallic cover complete with all connections 20.00 No. 196.00 3920.00

etc as required.

Supplying, installation, testing & commissioning of Fire

alarm Sounder with Facility to make annoucement,

mountedc in M.S Box (16 SWG) with Hinged cover plate

& Suitable for operation with Amplifier i/c line matching

e) 17.1.6 transformer etc complete as required . 2.00 No. 557.00 1114.00

CABLING & WIRING

Digitally signed by AMIT

S.NO. DESCRIPTION Qty UNIT RATE DSR AMOUNT

Supplying & laying of 2x1.5 sqmm fire survival alarm

armoured cable, 600/1000V rated with annealed copper

a) 17.5.2 conductor having XLPE insulation, steel wire armouring & 425.00 Metre 173.00 73525.00

ERLS outer sheath complete as required.

Add GST factor @1.0633 on DSR items 121319.3401

Add CPWD labour cess factor @0.973 118043.7179

Total Amount 14,500.00 118043.72

Total Amount 14,500.00 118043.72

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

DGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made

out of 25mm thick pre -laminated particle board of approved shade. The working and non working

edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be

supported with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm

x 40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk

pvc edge banding. The table shall be provisioned with Side unit of overall size: 1800mm(L) x

1 450mm(D) x 675mm(H) . Side storage having a provision for three equal drawer unit and two Nos 1.00 44,600 44,600.00

openable shutter & one open storage with shelf in it. The Side unit top shall be made out of 18mm

thick pre laminated particle board and rest all storage to be made out of 18mm thick pre laminated

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or

as per site requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side

Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

DGM High Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size

Back Chair :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design

contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

upholstered with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is

provided for extra comfort. The chair shall be provided with pneumatic height adjustment which shall

have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

DGM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm

Back Chair X (H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium

Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back

3 Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating Height:19".The Nos 3.00 14,500 43,500.00

Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane

foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

3 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the

DGM Cabin/ soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour

Reception Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech

solid wood have used for framing construction of sofa .The seat cushion is made of multi layered

foam of density 32-35 kg/m3. The seating cushion have 2.75 &

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength .

The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

GM Cabin/ Dimension(L)1390mm

Supplying, and placing Xin(D)750mm

position of XCofee/

Corner Table as per approved design

5 Reception Dimension(L)450mm X (D)450mm X (H)450mm Nos 2.00 10,500 21,000.00

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

AGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made

out of 25mm thick pre -laminated particle board of approved shade. The working and non working

edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be

supported with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm

x 40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk

pvc edge banding. The table shall be provisioned with Side unit of overall size: 1800mm(L) x

6 450mm(D) x 675mm(H) . Side storage having a provision for three equal drawer unit and two Nos 3.00 38,790 116,370.00

openable shutter & one open storage with shelf in it. The Side unit top shall be made out of 18mm

thick pre laminated particle board and rest all storage to be made out of 18mm thick pre laminated

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or

as per site requirement. Main Table Dimension (L)1800mm X (D) 900mm X (H)750mm overall Side

Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

AGM Chair Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof

plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS

grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be

provided with self tension single locking mechanism and pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height adjustment shall have adjustment

stroke of 100 mm and shall be operated at 30kgs extension force.The Seat & back are made up of

12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of

density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of

chair AGM Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design

Cabin contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

8 upholstered with leatheritte and cut foam. The chair shall be provided with pneumatic height Nos 6.00 12,450 74,700.00

adjustment which shall have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg

Conference /m3) The backrest

Supplying has in

and placing a foam of 28kg/m3.

position of conference table of required size as per image/drawing. The work

Table surface top should be of thickness 42mm top prelaminated particle board with 2mm thick PVC edge

banding. The side panel are made up of 36mm thick prelaminated particle & modesty panel are

9 made out of 25mm thick prelaminated particle board with 2mm thick PVC edge banding. The wire Nos 1.00 77,500 77,500.00

carrier should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a

provision of 6 module flip top box & metal raceway for wire flow.

Confrence Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

high back 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof

Chair plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS

grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be

provided with self tension single locking mechanism and pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height adjustment shall have adjustment

stroke of 100 mm and shall be operated at 30kgs extension force.The Seat & back are made up of

12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of

density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of

chair Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design

Confrence contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

11 room upholstered with leatheritte and cut foam. The chair shall be provided with pneumatic height Nos 12.00 12,450 149,400.00

adjustment which shall have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg

/m3) The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Modular Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side

Workstation Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht.

1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side

laminated and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end

18mm thick MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H

made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For

drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating- Munshel Gray. and White

Linear Tinted Glass1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

Workstation workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and

50mm x 25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk

Metal panel fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation).

0.8 mm thk Single/Double metal powder coated raceway with Powder coting of 50 Micron below top

for wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non-

13 sharing workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of Nos 11.00 26,500 291,500.00

glass divider rest on the "D" brackets on the table top between opposite seatings. All working or non

working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt

glue at hot temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of

2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Meeting Table Supplying and placing in position of Round Table 1200X1200X750 mm 1200mm Dia table of required

size as per image/drawing. The work surface top should be of thickness 42mm top prelaminated

particle board with 2mm thick PVC edge banding. The side panel are made up of 36mm thick

14 prelaminated particle & modesty panel are made out of 25mm thick prelaminated particle board with Nos 1.00 46,500 46,500.00

2mm thick PVC edge banding. The wire carrier should be made from 0.6mm thick CRCA & powder

coated 40-50 microns. Also having a provision of 6 module flip top box & metal raceway for wire

Medium Back flow.

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of

chair Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design

Workstation/ contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

15 Reception/ upholstered with leatheritte and cut foam. The chair shall be provided with pneumatic height Nos 26.00 12,450 323,700.00

Meeting room adjustment which shall have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg

Pantry Table /m3) The &

Providing backrest has aoffoam

Installation of 28kg/m3.

Pantry table of size 1.8m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design.

16 The Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided Nos 1.00 26,500 26,500.00

above table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Reception Providing & Installation of Reception table of size 1.2m x 0.75m x .9 m (ht) made out of 19mm thk.

Table Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design.

17 The Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided Nos 1.00 24,500 24,500.00

above table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC 8.00 4,500

Openable The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is

Shutter made of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided with

19 storage machine pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free

groove handle and suitable lock. All exposed area PVC edge lipping

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

2 BAY COMPACTOR

MECHANICAL DRIVE SYSTEM

Technical Specication

*Verticals: - In 0.8 mm Thickness CRCA sheet & shall be in

8-fold Box Type design in full panel form.

* Shelves: - In 0.8mm Thickness in 10 fold design to take

a load of 60 kgs UDL.

*Center Partition : In 0.8 mm Thickness, shall be in full

sheet in 2 parts & each shall have 2 nos. ribs for

strength & rigidity, this shall be used as center partition

*The Backs of the Single Fixed unit shall be closed by Box

*Base Frame: - Shall be fabricated from formed channels

of size 40 x 100 x 3mm thick made from HR steel &

internal supports in 2mm HR.leveller.

20.0 Pantry Under Counter Storage, made with HDHMR board finished with laminate on all

exposed surfaces. Unit depth: 600mm. All edges shall be finished with matching edge

banding. Includes shutters, shelves, hardware (hinges, handles), and necessary fittings

complete in all respects.

21.0 Pantry Overhead Storage Unit, made from HDHMR board of approved shade and grade

conforming to E1 norms, with unit depth of 450mm. All exposed edges finished with 2mm

PVC edge banding using hotmelt EVA glue. Includes shutters, shelves, and necessary

hardware and fittings, complete in all respects.

Total Amount 2,554,840.60

Total Amount 2,554,840.60

Digitally signed by AMIT

Description Unit Qty. Rate Amount

4221 LED Down lighter (COB Type) (System lumen efficacy ≥ 105 < 120lm/Watt) Supplying of LED

Recessed/ surface Down lighter (Round/ square/Rectangular) COB Type of following body

material and construction as per IS : 10322 with driver as per the requirement with Driver

efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp

range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open

circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI>80, UGR (Unified Glare Rating) < 19, Flicker

free (flicker should be below 5%), life time (LED,Driver & electrical circuitary), of minimum

50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K /

5700°K / 6000°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3,

Maximum power consumption should not more than the specified rating and Fixture shall

be confirming to relevant BIS standards and trade mark certificate (T.C.). Manufactures Nos 60 566.00 33960

Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect

i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable

and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy

≥105 and <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing

required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body

including trim with Aluminium Reflector 12 -15 watt

Digitally signed by AMIT

Description Unit Qty. Rate Amount

4258 LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying of Panel light 2x2

ft., of following body material and construction

as per IS : 10322 with driver as per the requirement with Driver efficiency>85%, Operating

voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection,THD <

10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be

below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with

, 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K /

5700°K/6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3,

Maximum power consumption should not more than the specified rating and Fixture shall

be of relevant BIS standard and trade mark certificate (T.C.). Manufactures Word Nos 40 2700.00 108000

Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c

connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable

and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy

output . LM79 & LM80 Test report from NABL lab for all testing required

for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be

as approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C).

Total coated items

of Electrical die cast /Extruded aluminium Body (Thickness > 141960.00

Digitally signed by AMIT