CONSTRUCTION OF SINGLE LAB OF SIZE 7 MTR X 10.30 MTR AT PM SHRI KENDRIYA VIDYALAYA, LANSDOWNE (PM SHRI SCHEME)

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ disintigrated rock comlete all as specified and directed.

Removing excavated material (Soft/ disintigrated rock) exc 1.5 KM but n.exc 5.0 KM and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation or for shafts, well cesspits, manholes etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in soft/ disintegrated rock complete all as specified and directed.

M&L for PCC (1:4:8) Type D2 (40 mm graded aggre-gate) as in foundations, filling and mass-concrete or sub base of floor/ hard standing/ footpath complete all as specified and directed.

M&L for formwork for rough finish to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for formwork for rough finish to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for formwork for rough finish to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for formwork for rough finish to soffits of suspended slabs such as roof slabs, floor slabs, landing slab and similar work, not exceeding 200mm thick complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for 10mm thick rendering on brick or concrete surface in cement plaster (1:6) finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick plastering on fair faces of brick wall in two layers, Ist layer 10mm thick CM (1:6), and IInd layer 5mm thick CM (1:4), surface finished even and fair mixed with @ 200ml per bag WPC (liquid type) complete all as specified and directed. Note :- WPC (Liquid type) shall be measured and paid separately as supply only.

Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed.

M&L for 5mm thick rendering on concrete surface in cement plaster (1:4) as in ceiling and fininshed surface even and fair complete all as specified and directed.

M&L for preparation of new wall surface and applying two coats of plastic emulsion paint over a coat of primer complete all as specified and directed.

M&L plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for three coats of white wash on new ceiling surfaces including preparation of surfaces complete all as specified and directed. Note :- The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge.The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted.

M & L for preparation of newly plastered or previously untreated surfaces of external wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.complete all as specified and directed

M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed. Note : Joint to be provided at each interval of 3m and corner and cost of the same deemed included in quoted rate.

M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles, raft etc and mass concrete complete all as specified and directed.

M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in floor/ roof beam, cantilevers, lintel over 1.5m span complete all as specified and directed.

M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable and variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

65 mm x 100mm size

M&L for 35 mm thick factory made single extruded WPC (Wood Polymer Composite) solid decorative flush door shutter comprising of virgin polymer of K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant WPC to be laminated with PVC foil of min 14 microns thick of approved design pasted with hot melt adhesive on both face of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and directed. Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately.

M&L factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) complete all as specified and directed.

Area not exceeding 2.00 sqm each

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden/ PVC/ aluminium beading, in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and or riveted or forged into spikes, framed, barred iron door, ladders, fencing work ect. conforming to Fe-290 Gde E-165 complete all as specified and directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 250 mm long anodised aluminium sliding door bolt (ISI marked) with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed

S&F 200 mm long anodised aluminium barrel tower bolts (ISI marked) of extruded section complete all as directed and specified

S&F extruded aluminium alloy handles,150 mm fabricated type, anodised (ISI marked) complete all as directed and specified

S&F hasp and staple, 100 mm safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed.

S&F galvanised steel 15 mm bore water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, concealed in wall,floor and ceiling or laid in trenches complete all as specified and as directed.

S&F galvanised steel 20 mm bore water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, concealed in wall,floor and ceiling or laid in trenches complete all as specified and as directed.

S&F vitreous china counter top wash hand basin, snow white, flat back, size 560 x 470 x190 mm excluding taps, waste pipe & waste coupling complete all as specified and directed. Note : Rate quoted under this item deemed included fixing of taps, waste fittings and union, plug and chain and connecting up to supply pipes, wastes or traps etc.

S&F 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated , Fancy type screwed down for pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed.

M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves complete all as specified and directed.

M&L for 18-20mm thick granite stone slab (of any type) work (table rubbed and mirror finish polished) with and including necessay notching, chamfering the edges in steps, jambs, pillars, window-cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

M&L for mirror polished machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror finish polishing over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

Description same all as per item No 41 above but, as in riser of steps ( 18-20 mm thick Kota stone ) over and including 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed. Note : Only one stone piece on one riser must be use.

M&L for PCC (1:5:10) Type D2 (40 mm graded aggre-gate) as in foundations, filling and mass-concrete or sub base of floor/ hard standing/ footpath complete all as specified and directed.

Returning, filling in, rocks including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

M&L for hard core of broken boulders/stone of gauge n exc. 63 mm, deposited, spreading, leveling watering and well ramming to true surface in layers not exceeding 15 cm thick each layer complete all as specified and directed.

S&F PVC (SWR) bends 75 mm bore pipe any radius including necessary cutting in brick wall and making good to match with existing surface complete all as specified and as directed.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints and laid in trenches or in floor complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints and laid in trenches or in floor complete all as specified and as directed.

S&F grating doom 100mm dia of PTMT (with waste hole or without waste hole)(Min wt 25 gms) complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank, Capacity 500 Ltrs double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, complete all as specified and as directed.

M&L 20 mm bore dia of pipe Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F 20 mm bore stop valve, cast copper alloy with crutch handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F for stainless steel non magnetic curtain rod of 20mm dia with and including fixing brackets and decorative type knobs (as approved by AGE (I)/ GE both side of each rod complete all as specified and directed. Note: - Measurement will be taken between end point of knobs.

M&L for 15 mm screed bed or bedding layer in cement mortar 1:4 mixed with WPC as per manufacturer instruction over RCC slab horizontal or vertical portion for laying water proofing treatment all as specified and directed. Note :- WPC (Liquid type) shall be measured and paid separately as supply only.

M&L for applying bituminous primer @0.40 ltr/Sqm with density of 0.87 to 0.89 kg/ltr on existing concrete roof surfce complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

M&L painting on new APP based polymeric membrane surface and applying solar reflective aluminium paint complete all as specified and directed.

M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:6) including necessary fair finish formwork complete all as specified and directed.

M&L for cast iron Nahani trap 75 mm dia with grating including jointing to waste pipe fixed in PCC (1:2:4) type B1, complete all as specified & directed.

S&F PVC (SWR) junction single, (single T) 75 mm bore equal or unequal complete all as specified and as directed. :-

S&F 450 mm long PVC connection 15 mm size with PTMT nut complete all as specified and directed.

M&L for 100 mm thick PCC (1:3:6) type C2, (40 mm graded stone agg) as in sub base of floor complete all as specified and directed.

Removal of surplus soft disintigrated rock to a distance n'exc. 50 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for 30cm x 30cm x 25mm thick rubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continuous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed rigid PVC conduit(ISI marked) ,duly cutting chases & concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) including metal flush box made of GI sheet and white cover with making good the disturbs surfaces of wall/floor/ceiling complete all as specified and directed for the following. Note: Flush box and cover plate should be of same make all as approved for switches/sockets.

One light/fan/bell point controlled by one No modular type switch 6 Amps single pole one way complete all as specified and directed.

One 3 pin 6 Amps socket outlet on same board controlled by one, one way 6 Amps modular switch complete all as specified and directed.

One socket outlet 5/3 pin 6 Amps controlled by one modular switch on independent board complete all as specified and directed.

All as per item No 65 here-in-above but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated FRLSH but unsheathed single core for 16 Amps power point on independent board and 2.5 sqmm FRLSH cable as earthwire complete all as specified and directed.

S & F switch Modular single pole, one way 6 Amps , 1 module, 230 volts, 50 hz complete all as specified and directed.

Supply and fix Modular switch 1 way 16 Amps, 1 module, 230 volts, 50 Hz complete all as specified and directed.

Supply and fix Modular Socket outlet, 6A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed.

Supply and fix Modular Socket outlet, 16A - 2/3 pin combined, 2 module ISI marked, 230 volts, 50 hz complete all as specified and directed.

S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as speccified and directed

S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed

DB SPN, 8 way

S&F MCB , SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F MCB, SPN, AC, 415 volts of 63 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F surface mounted LED luminiare, 20 watt 4 feetwith all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed. Note: The firm has to give warranty for fitting including driver minimum for 2 years for any defects developed during the period.

S&F LED building security light 1 x 20 W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.90 having over voltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit protection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70, including fixed on wall with 1.2 mtr 32 mm GI pipe bracket & 02 Nos MS clamp made out of F1 40 x 6 mm or as directed including connecting with 1.5 sqmm , 3 core, PVC insulated copper conductor cable 1100 Volt grade from ceiling box to light complete all as specified and as directed.

S&F 16 Sqmm twin core cable flat of PVC insulated, stranded aluminium conductor, 1100 volts grade heavy duty cable served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than one mtr apart including 4 mm dia suspension wire complete all as specified and as directed.

S&F Exhaust fan Steel body AC single phase 230 Volt of size 300 mm sweep complete with blade, Frame and louvers including making hole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4 mm GI Wire check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI strip upto 7.5 mtrs long with 15 mm dia medium grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI strip more than 7.5 mtrs will be measured and paid seperately under relevant items.

Supply and hanging ceiling fan five star rating with double ball bearing 350 RPM, 1400 mm sweep, working on 140-285 Volts AC 50 Hz, PF 0.99 with super energy efficient BLDC motor & power consumption shall not more than 28W under standard test condition along with down rod, canopy and all accessories, with smart remote control, all as supplied by manufacturer and making necessary electrical connection with 3 core flexible copper conductor 1100 volts grade of suitable size (not less than 1.5 sqmm) and length including and making necessary electric connection etc complete all as directed. Make: Havellls/Crompton/Philips. Note: Contractor shall submit the guarantee from manufacturer for ceiling fan for minimum 3 years for any defects developed during the period.

S&F 25 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F 1 HP(0.75 KW) pump set self priming Pump single phase 220 volts 50Hz 2700/2800 RPM head up to 08 mtr discharge up to 3300 LPM aluminium body motor brass impeller cast iron delivery casting carbon steel pump shaft including strainer complete all as specified and directed.

PIONEER REFRIGERATION AND ELECTRICALS (BID ID -3364939)

M/S Balaji Builders (BID ID -3366525)