SPECIAL REPAIR TO BLDG NO. T-17 AND T-19 IN BOS AREA AT YOL CANTT

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of reinforced cement concrete ((reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of brick work or stonework built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed

Taking down and removing chowkats with shutters (without taking off shutters from chowkat) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down and removing chowkats with shutters (without taking off shutters from chowkat) exc 1.50 Sqm but not exc 4.00 Sqm each complete all as specified and directed. .

Taking down shutter of any description not exc 1 sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but not exc 2 sqm each complete all as specified and directed.

Taking down of alumimium three/two track sliding window including with all fittings, repairing and refixing the alumimium three track sliding window in servieable condition in same opening.

Taking down of alumimium door shutter with frame including with all fittings, repairing and refixing the alumimium door shutter with frame in servieable condition in same opening.

Taking down steel water tubing 15 mm bore including all fitting and connections complete all as specified and directed.

Taking down steel water tubing 20 mm bore including all fitting and connections complete all as specified and directed.

Dismantling timber in scantling 40 sqcm and over in section, framed work complete all as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, framed work complete all as specified and directed.

Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling plain or corrugated steel sheets any gauge thickness including Nanital or similar pattern roof covering including ridges complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises. complete all as specified and as directed.

Dismantling water storage tank of capacity exc 250 ltr but n.exc 500 ltr complete all as specified and directed. .

Dismantling water storage tank of capacity exc 500 ltr but n.exc 1000 ltr complete all as specified and directed. .

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Demolition of Matting, single or double any type including, bamboo framing or bamboo supports, cover fillets, if any complete all as specified and directed.

Taking Down Wall to wall shower enclosure with one fixed glass and one openable door fixed on wall -2 parts having 8 to 12 mm glass with chrome finish and refxing in servicable condition complete all as speciied and directed by Engr.-in-charge.

Plain cement concrete 1:2:4 ( nominal mix ) type B-0 (using 12.5mm graded crushed stone aggregates) as in cement concrete in roof kerbs or mud stops, rounded or chamfered on edges, lintels upto 1.5m clear span, cills, steps; seismic and other similar ands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork where required complete all as specified and directed.

PCC 1:3:6 (nominal mix) type B-2 (using 40mm graded crushed stone aggregates) as in surface channel and drains including necessary form work complete all as specified and directed.

RCC 1:2:4 ( nominal mix ) type B-0 (using 12.50 mm graded crushed stone aggregates ) as Beams, Cantilevers, bressummers, lintels over 1.5m spane complete all as specified and directed.

RCC 1:2:4 ( nominal mix ) type B-0 (using 12.50 mm graded crushed stone aggregates ) as Columns, pillars, piers, posts and struts complete all as specified and directed.

Use & waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, complete all as specified & directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 all as specified & directed.

Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 all as specified & directed.

Factory made solid PVC Door Frame of size 50mm x 95mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed.

Natural colour 15 micron anodized aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM. b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM. c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM. d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM. e) Anodised aluminium handle, fancy type, 350mm long and aluminium tower bolt of size 150mm. (f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. Note:- (i) Shutter shall be fixed with heavy floor spring ISI marked and pivot, brass lock with duplicate keys.

Natural colour 15 micron anodized aluminium window with chowkhat of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a)Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM.(b)Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM.(c)Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM.(d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed.(e) 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets complete. (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos).

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Factory made fully glazed, PVC window/ventilator shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; supply & fixing in the frame at site as per specification & drawing complete all as specified and directed.

35mm thick , 2nd class hard wood , Plain framed, panelled shutter,without interlocking rail and with one panel and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

35 mm thick 2nd class hard wood (Sal/Hollock) glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members of door shutters as specified in SSR- 2009 Part-I Section 8.24(a) complete all as specified and directed.

12 mm thick toughened glass shutters (single Leaf openable type) with diamond polished edge, clear glass including all hardware fittings detailed as under, fixed in position as per manufacturer instructions including following fittings complete.:- (a) Stainless steel top patch (cat No. EPF - 701) 01 set (b) Stainless steel top pivot (cat No EPF-712) 01 set (c)Stainless steeel bottom patch (Cat No EPF-702) 01 set (d) Glass to wall stainless steel lock (Cat No FH-ECO -842) 01 set (f) Stainless Steel Handle 300mm size (Cat No ESBH-011) 02 Nos for each shutter . Note :- Cat No. mention above for hardware fittings are of make ENOX, contractor may use similir type hardware fitting of make DORMA/OZONE. Make of glass ATUL/MODIGUARD/SAINT GOBAIN

Natural colour 15 micron anodized aluminium anodized sliding window shutter of section (Hollow) of vertical style, top rail and bottom of size 45x25mm and 2mm thick, shutter with 5.50mm thick tinted glass fixed with anodised aluminium snap beading and rubber gasket, glazing clips, fancy type aluminium anodised handle, shutter fixed with aluminium track including 2 Nos of roller for each shutter, 02 Nos automatic lock, anodised aluminium snap beading screws, jointing cleats complete all as specified and approved by GE. Note : Track shall be measured and paid separately.

Natural colour 15 micron anodized aluminium anodized three way track (Guide rails) of size 65.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM for window shutter complete all as specified and approved by GE.

Supply fabricate & fix in position aluminium partition wall with top , middle and bottom frame of size 101.6x44.45x1.75mm weighing 1.367KG/RM , partly glazed with 5.5mm thick tinted glass with or without sash bars and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, Note:- (i) Section No given above are of make jindal, contractor may use similar section of other make mention in Appx 'C'

Extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 100 mm complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 150 mm and fixed complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 100 mm and fixed complete all as specified and directed.

Mild steel butt hinges of size 100mm medium weight cold rolled complete all as specified and directed.

Mild steel butt hinges of size 75mm medium weight cold rolled complete all as specified and directed.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Door closer hydraulically regulated, Aluminium (extruded section ) body,designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm, complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Sheet glass, 3 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh including Aluminium anodised snap grid frame work of size of size 605 mm X 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/ instructions), cutting holes for electrical fittings fixed on and including aluminium tee of size 25mmX25mmX1.50 mm as main runner, aluminium tee of size 25mmX25mmX1.25 mm as cross runner and aluminium angle of size 25mmX25mmX1.25mm at the perimeter suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long including necessary scaffolding all as specified and directed.

Solid Prelam PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing,complete all as specified.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified & directed.

18/19 mm thick, Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in wall panelling/cup board shutters complete all as specified and directed.

0.63 mm thick, galvanised, plain mild steel sheeting as in ridges, hipe, valley gutters, drip and straight flashing (length and girth as fixed) with grade of zinc coating 275 gms per sqm complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square not., Exc 30cm long., diameter of neck exc 12 and not exc 20mm, complete all as specified.

Rolled mild steel work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

Rolled mild steel work as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Plain cement concrete 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in floor finish, surface finished even and fair to receive top finish complete all as specified and directed.

PVC tiles/ sheets, 1.5mm thick,laminated plain coloured, marbled mosaic or mottled finish, laid with approved rubber based adhesive in floors complete all as specified and directed.

Vitrified ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm as directed by EIC, as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:6 including roughening of old concrete surfaces of floor by picking, sweeping, cleaning and washing with water to remove all loose dirt etc. complete all as specified and directed.

Vitrified ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm as directed by EIC, as in skirting/vertical surfaces etc , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Mat finish, premium quality, joint free (edge cut), coloured/ printed Non -Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic coloured tiles of size 450mm x 300 mm x 7mm / 350mm x 250 mm x 7mm thick as in skirting/vertical surfaces etc , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE.

20mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. complete all as specified and directed.

20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, laid over and including 10mm thick rendering in cement mortar 1:4 complete, all as specified..

Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 including cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Endura tiles 12mm thick in parking, step treads & risers in stair case set and jointed in over and including 15mm thick screed bedding layer of cement mortar in CM 1:6 with complete all as specified.

7 mm thick slate tiles best quality locally available fixed on wall with neat cement slurry/ paste including rendering 15mm thick cement mortar 1:4 on stone masonary/ brick masonary size and pattern to be laid as orderd by Engineer-in-Charge, all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying two coats of oil bound distemper finished smooth complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Preparation of old surfaces of wall by Complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Preparation of new plastered surfaces or un plastered, previously undecorated wall surfaces and applying two coats of cement base paint over one coat of white wash, complete all as specified and directed.

Preparation of old surfaces of wall by Complete removal of existing treatment and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

G I tubing medium grade of 15 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor/trenches complete all as specified and directed.

GI tubing medium grade of 20 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

Harrison rail (Curtain rail), mild steel, chromium plated with and including fixing brackets, stops, rollers etc. complete all as specified

Sink with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 910mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Wash basins, Vitreous China , counter table top Size: 495x395x150 mm, coloured ,fixed in granite counter by making suitable holes, new brackets with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia , 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete fixed in repair all as specified. Make: Cat Part No. JDS-WHT-25909 of Jaquar or equivalent in makes mentioned in Appx

75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

Stop valve/Angle Valve cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Stop valve/Angle Valve, fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair complete all as specified and directed.

Soap dish, SS, approximate size 160x 160x90mm, any type, fixed to plugs with chromium plated brass screws, fixed in repair complete all as specified.

Steel plate rack of overall size 900mm x 750mm x 250 mm made of stainless steel having thickness 1mm, fixed over fixing over 40cm long MS angle of size 25mmx25mmx3mm - 02Nos each , fixed in repair complete all as specified and directed.

32mm bore Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 260ms ) complete all as specified

S&F in repairs, Wall Mixer with Provision For Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges complete all as specified. Make : Jaquar Cat Part No. CON-273KNUPR or its equivalent approved make

S&F in repairs, Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hook complete all as specified. Make : Jaquar Cat Part No. ALD-565 or its equivalent approved make

S&F in repairs, Central Hole Basin Mixer with Popup Waste System with 450mm Long Braided Hoses (15mm Cartridge Size) complete all as specified. Make : Jaquar Cat Part No. SOL-6169B or its equivalent approved make

S&F in repairs, Towel Rack with Lower Hanger (Stainless Steel) with hook complete all as specified. Make : Jaquar Cat Part No. AHS-1581H or its equivalent approved make

S&F in repairs, Maze Overhead Shower 150x150mm Square Shape Single Flow (Body & Face Plate Stainless Steel) with Rubit Cleaning System complete all as specified. Make : Jaquar Cat Part No. OHS-1605 or its equivalent approved make

S&F in repairs, Stainless steel structure, shower panel, 1500mmx200mm, having 3 adjustable vertical jets (Square) enclosed with intergrated shower head (8 inch Square), fitted with Thermostatic mixer with diverter and a hand shower with flexible hose fitted with button spout on a glass platform with multi function water sprayer complete all as specified. Make : Jaquar Cat Part No. JPL-BLK-JA011 or its equivalent approved make

S&F in repairs, Toilet Paper Holder with Flap Recessed Type (Stainless Steel), fixed to walls with chromium plated brass screws, complete all as specified. Make : Jaquar Cat Part No. AHS-1553 or its equivalent approved make

Vitreous China wash down water closet , Rimless, Blind Installation Wall Hung WC with UF soft close slim seat cover,Hinges, Accessories set, Size : 360x500x335 MM (pedestal pattern) including Single Piece Slim Concealed Cistern with Wall Mounting Frame, Installation Kit and “S-Type” Drain Pipe Connection Set for Wall Hung WC (with Flush Control Plate), complete including fitting connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, complete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs all as specified. Make: Cat Part No. KUS-WHT-35953BIUFSM (For WC), JCS-WHT-2400WS (for cistern) , JCP-CHR-392415 (for cover plate) of 'Jaquar' or equivalent makes mentioned in PS.

600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

PVC (SWR) 110mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls, including taking down unserviceable pipe, fittings, etc, complete all as directed and all as specified.

PVC (SWR) 75mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls, including taking down unserviceable pipe, fittings, etc, complete all as directed and all as specified.

PVC (SWR) 110mm bore (dia), Bends any type, with access door, with disminishing pieces or tapers and Jointing with Solvent Cement, complete all as specified and as directed.

PVC (SWR) 75mm bore (dia), Bends any type, with disminishing pieces or tapers and Jointing with Solvent Cement, complete all as specified and as directed.

PVC (SWR) 110mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

PVC (SWR) 75mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing ceiling/ exhaust fan and electric meters are to be refixed and connected properly where required.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surface complete all as specified and directed.

Point wiring with copper conductor cable multistrand, PVC sheathed 1.5 Sqmm size(two run with colour code RYB for phase and black for neutral) for one light point ,fan point, exhaust fan point,or bell point controlled by one switch including one run of 1.5 Sqmm (as continous earth wire Green)multistrand PVC concealed conduit of approved size and quality ISI marked,including all other required accessories as specified in preamable 1(a) to (q) of section 19 of SSR Part-II under heading 'point wiring' fixedon wall/ceiling including concealed PVC/MS pressed steel cadmium plated modular terminal box not less than 1.6 mm thick for mounting switches, sockets, fan regulators etc and 3 mm thick modular laminated sheet top cover(ISI marked)cutting,chasing,pinning and making good the disturbed surface by using cement mortar 1:3 complete all as specified and directed by Engr-in-charge.,(Note:-the rate for concealed type point wiring shall deemed to include the cost of cutting,chasing in wall by using electric cutter and making good the disturbed surface of wall by providing cement plasterand matching the surface by white wash/colour wash all as per existing finishes complete).

All as per serial item No '122' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '122' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No. '122' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Modular switch 1 way 6A, 1 module, complete all as specified.

Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified.

Modular Bell push 6A 1 module, complete all as specified.

Modular switch 1 way 16A, 1 module, complete all as specified.

Socket 6A/16A - 2/3 pin combined , 2 module, all as specified and directed.

Modular fan regulator, step type, 2 module, all as specified.

Buzzer, Ding Dong AC. 230 volts, single pole, all as specified.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Pluto Neo Panel 2 feet X 2 feet, 36 Watt, environment friendly, new generation, aesthetically, ultra modern recess mounting luminaire with high brightness SMD LED's as light source complete with all accessories and fixtures prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete fixed in armstrong/ grid ceiling. Make : Havell's Cat Part No.PLUTONEO2X2PLR34WLED840S or equivalent in makes mentioned in Appx

Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack., 10 watt LED,6500k, tube rod with all acessoreis internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. Make: Havell's Cat Part No. LHEXACP7IN1W010 of "Havells" or equivalent in makes mentioned in Appendix

Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack. 1x18W, 6500K ,230V, connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. Make: Havells cat part No. LHEXACP7UN1W018 or equivalent in Appx

Decorative wall mounted brushed nickle finish fixture opal glass diffuser sutaible with 9 Watt LED lamp B22 Base connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable light all as specified and directed Make: Havells cat part No. LHFOAJE1TZ1I060 or equivalent in Appx

Endura Pearl 35Watt New generation energy saving and environmental friendly long life LED Bldg security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate toughtned glass/verminproof driver compartment, SPDs with IP66 protection and impact resistance of IK07. connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of suitable size, complete all as specified Make: Havells cat part No. ENDURAPEARLPLUSSL135WLED757PASYTOPCLC or equivalent in Appx

CONE LED BOLLARD, 8Watt , IP 65 Cone series acts as an imposing street furniture. The elegant yet minimalistic design acts a silent observer and giving light, diffuser at the upper portion adds functional value into landscape environment. connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting, complete all as specified. Make: Havells cat part No. CONEBL8WLED830PSYMTOPCM or equivalent in Appx

MCB SPN 32-40 Amp, 240 Volts, 10 KA all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified.

MCB TPN 63 Amps , 415 Volts, 10 KA all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar completed all as specified.

Concealed sheet metal enclosure with socket plug top and MCBs having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20Amp 240V complete all as specified and as directed.

Sheet metal enclosures for DBs when MCBs to be used, triple pole and neutral, 4 way, double door, 415 volts with 200 Amp rated bus bar including taking down ICDP/ DB's any type, kit kat fuse, MCB's any type, all as specified.

Taking down ceiling fan/exhaust fan complete of 1200/250/300 mm sweep from fan hook/wall dismentling blade opening of motor cleaning stator rotor, cleaning of all parts, greasing, oiling of bush & bearing, reassembling, & applying painting to one coat of synthetic enamel paint of approved quality and colour (spray painted) after preparing the surface throughly and refixing at site at same/different location all as specified and as directed & marked MES No also & refixing connecting with 2 core copper cable. complete all as specified directed Engr-in-Charge .

Rewinding of ceiling fan of any make/model/sweep including removal of existing burnt winding carefully from slots, cleaning the slots throughly with suitable cleaning agent, applying slot insulation and rewinding with super enamelled copper conductor of same gauge/same number of turns as that of existing and connecting the coil suitable to operate on 230 V, single phase, AC supply, permanent capacitor type, tying the winding and applying air drying the winding throughly and all as specified and directed.

Taking down water storage heater from electrical socket and plumbing connections kept aside in safe for reuse at same/different location duly preparation to old painted surface of storage water heater and painting of geyser 25ltr capacity with two coats of synthetic enamel paint (white colour) by using gun and refixing duly grouting nut, bolts, washers and plumbing connection making leak proof complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm, complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed. Note: Punned thickness shall be measured.

Sub class "B" bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed.

GI pipe light grade of size 50 mm dia laid in trenches/ walls including clamps, screws etc, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 35 Sqmm, 3.5 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 10 Sqmm, 2 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

Supply and replace of motor suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Supply and replace of blade suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Renewal of sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 4 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 4 Sqmm, shall be measured as one RM).

Supply and replace of body suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Supply and replace of louvers suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Taking down AC Meters, checking and repairing at site by repair/ replacing of contects, terminals and indicators, glass covers, plate screws , electronic circuits etc and re-fixing in same poistion, complete all as specified.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC (1:2:4), type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC (1:2:4), type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 35 of tender doucments.

MM Constructions

Eshaan Construction Co.

surinder kumar jindal & bros.