REPAIR MAINT OF ELECTRIC AND WATER SUPPLY

Amount

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames) complete all as specified and directed by Engineer-In-Charge.

S&F 2nd Class Soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer-In-Charge.

S&F 2nd class soft wood 35mm thick factory made panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Pt-I) kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-In-Charge.

S&F MS cold rolled Butt hinges medium weight 100 mm long complete all as specified and directed by Engineer-In-Charge.

S&F 300 mm long mild steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minium of 6 bolts and nuts four on bolt plate and two on stapple plate and fixed, complete all as specified and directed by Engineer-In-Charge.

S&F mild steel barrel tower bolts, 200 mm long, ISI market stove enamelled block with bright bolt and fixed complete all as specified and directed by Engineer-In-Charge

S&F mild steel pressed handles, 150mm size, oval type ISI marked stove enamelled black complete all as specified and as directed by Engineer-In-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) and boarding any thickness, including cover fillets complete all as specified and directed by Engineer-In-Charge.

M&L for 2nd class soft wood 20 mm thick in facia boarding fixed with nails in any situation planed one side with butt joints complete all as specified and directed by Engineer-In-Charge.

Dismantling timber scantling 40 sq cm and over in section in any position as in unframed work, complete all as specified and directed by Engineer-In-Charge.

M&L for 2nd class soft wood (Kail) as in scantling, clean sawn timber framed and fixed, Complete all as specified and directed by Engineer-In-Charge.

All as per srl item No 11 above but except timber, complete all as specified and directed by Engineer-In-Charge.

Dismantling of plain or corrugated steel sheeting , any gauge and thickness in roof covering including Nainital or similar pattern roof covering complete all as specified and directed by Engineer-In-Charge.

S&F 0.63 mm thick, galvanized, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roofs,walls etc with grade of zinc coating 275 grams per square metre. Complete all as specified and directed by Engineer-In-Charge.

All as per Srl item No.14 but except sheeting complete all as specified and directed by Engineer-In-Charge.

S&F 0.80 mm thick plain , galvanised , mild steel sheeting , in ridges, hips, valley gutters, drip and straight flashing ( length and girth as fixed ) with grade of zinc coating 275 grams per square metre complete all as specified and directed by Engineer-In-Charge.

M&L for preparing new zinc (or galvanized) surfaces to receive painting by coating with mordant solution including washing and cleaning etc. of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer. Note :-(a) The surface of corrugated steel sheeting shall be measured flat (not girth) without any extra allowance for laps and the area obtain shall be increased by 14%).(b) The surface of plain steel sheeting as in ridge, hips, velley gutters, flashings etc, shall be measured flat alongwith girth (length and firth as fixed) and the area obtained shall be added to the area of corrugated steel sheeting, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of old painted zinc or galvanised surface of any description and in position and applying one coat of synthetic enamel paint all as specified. Note :-(a) The surface of corrugated steel sheeting shall be measured flat (not girth) without any extra allowance for laps and the area obtain shall be increased by 14%).(b) The surface of plain steel sheeting as in ridge, hips, velley gutters, flashings etc, shall be measured flat alongwith girth (length and firth as fixed) and the area obtained shall be added to the area of corrugated steel sheeting, complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of old surface including brooming down or steel wire brushing scrapping down smoke soot moulds moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of cement base paint on old plastered or un-plastered surface of walls complete all as specified and directed by Engineer-In-Charge.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-In-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-In-Charge.

M&L for 25mm thick PCC 1:2:4 type B-O (using 12.5 graded aggregate) as in floors finished even and fair complete all as specified and directed by Engineer-In-Charge.

M&L for 75 mm thick cement concrete of 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed by Engineer-In-Charge.

M&L for damp proofing course to horizontal surface including necessary formwork in cement mortar 1:2:4, type B-0, 40mm thick complete, complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth complete, complete all as specified and directed by Engineer-In-Charge.

S&F glazed ceramic coloured tiles 7mm thick 450 x 300mm size in verticle surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 15mm thick CM (1:4) complete all as specified and directed by Engineer-In-Charge.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified and directed by Engineer-In-Charge.

M & L for machine cut kota stone slab flooring 20 - 25mm thick over 15mm cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to the match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-In-Charge.

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in deep in hard/dense soil/ road for getting out old GI tubing from the trenches etc, complete all as specified and directed by Engineer-In-Charge.

Removing excavated material of any type of soil/soft rock from site to a distance not exceeding 50mtr away and depositing where directed not exceeding 1.5mtr above the starting point complete all as specified and directed by Engineer-In-Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil complete all as specified and directed by Engineer-In-Charge.

Material and laying in repairs GI tubing medium grade ISI marked complete with all necessary fittings of sizes 50 mm bore in trenches complete all as specified and directed by Engineer-In-Charge. Make : Jindal /Prakash /TATA, Surya.

S&F in repairs gun metal gate valve 50 mm bore with iron hand wheel head , screwed both ends for iron pipes and fixed complete all as specified and directed by Engineer-In-Charge. Make: Kirloskar/ Zoloto / Venus/Prayag.

M/S HAJI MOHD ASHRAF SUMJI

M/S NISAR AND CO

M/S GHULAM QADIR WANI AND SONS