CA NO GE(N)AMB-18/2025-26 REPAIR TO JOINERY, PLUMBING, SANITARY, PLASTERING, CERTAIN E/M WORKS AND OTHER CONNECTED BLDG REPAIR WORK IN HQ CORPS COMPLEX UNDER AGE B/R-II OF GE (NORTH) AMBALA CANTT

Amount

Schedule 'A' Part-I (B/R itmes) Dismantling of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar, etc. but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc. complete all as specified and as directed by the Engineer-in-Charge

Material and labour rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement complete all as specified and as directed by the Engineer-in-Charge. ( Note- The cost of providing WPC shall be included in quoted rate under this item )

Material and labour for rendering 10 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finishing the surface even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering 05 mm thick on fair faces of brick work or concrete ceiling surfaces, chajjas, etc. in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of acrylic distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces and applying three coats of white lime wash on surfaces of walls, chajjas, roof projection etc., complete all as specified and as directed by the Engineer-in-Charge.

S & F stainless steel curtain rod 25mm dia having wall thickness 1.00mm fixed with and including stainless steel decorative brackets, two lotto for each rod length at both end etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing PVC connections 15 mm size and 600 mm of length with PTMT nuts and PVC washers on both ends as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Material and labour for galvanised iron tubing 15mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Material and labour galvanised iron tubing 20 mm bore, ISI marked, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair bib tap 15mm bore fancy type brass chromium plated with long body, ISI marked, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, ISI marked, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair 15mm bore cast copper alloy chromium plated angular stop valves, ISI marked, screwed down, high pressure with capstan head, screwed down both ends for iron pipe or for unions complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of vitreous china wash hand basin white with pedestal, ISI marked, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling chromium plated and 32 mm dia PVC waste pipe including fixing of waste fitting, etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair vitreous china squatting pan, Orissa pattern, 580 mm x 440 mm size, white colour with integral foot rest and PVC SWR 'P' or 'S' trap of pressure rating 6 Kg per square cm complete including provision of cement concrete bedding, connection to trap, outgoing flushing pipe, anti syphonage pipe, etc. complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement 10 litre PVC valveless syphonic action type flushing cistern with inlet ball valve float, handle, etc. with and including brackets, flush pipe, etc. and connections of flush pipes to WC complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing for vitreous china wash down water closet pan (pedestal pattern), white (including fixing bolts but excluding flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom cover and mild steel chromium plated or aluminium hinges device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Taking down existing sensor from urinal of any type and material & labour for servicing the same by replacing spandles, sensor connector, connecting pipe, wires, batteries/cells etc., and refixing the same to make it operational, complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully existing urinal and supply and fixing new half stall type, vitreous china urinal with and including sensor & all connected accessories as per manufacture instructions and fixing the same on wall to make it operational, complete all as specified and as directed by the Engineer-in-Charge. Make :- (urinal : Jaquar Cat Part No : URS-WHT-13255 & sensor Jaquar Cat Part No : SNR-51097) or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

S & F sinks without drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm as in repair , complete, all as specified and as directed.

Supply and fixing of plastic water closet seat cover , white closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 32 mm dia PVC waste pipe of standard length for wash hand basin / Kitchen sink etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

Disconnecting existing water tanks of capacity 500 ltr setting aside (or lowering if required) & cleaning and removing all scale and dirt etc from in side of PVC/RCC tanks and mouths of circulating pipe & writing date of cleaning on the tank with synthetic enamel paint not less than 200mm long and 20mm wide of words and reconnecting and refixing of the tank in position to make it operational, complete, all as specified and as directed by the Engineer-in-Charge. NOTE :- (i) The unit rate shall be included cost of small fittings such as elbow, socket, reducer, tee, union, etc. (ii) The whole process of reconnecting and refixing in position after cleaning/after carrying out water proofing treatment shall be done on the same day to ensure uninterrupted water supply to the occupant, if failing so, Rs. 200/– shall be deducted for each tank per day from the contractor due.

Supply and fixing , water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including disconnecting and dismantling of existing water tanks and removing from site all as specified in SSR Part–I , complete all as specified and as directed by the Engineer-in-Charge. Note : - The colour of tanks shall be white colour .

Disconnecting existing water tanks of capacity 1000 ltr setting aside (or lowering if required) & cleaning and removing all scale and dirt etc from in side of PVC/RCC tanks and mouths of circulating pipe & writing date of cleaning on the tank with synthetic enamel paint not less than 200mm long and 20mm wide of words and reconnecting and refixing of the tank in position to make it operational, complete, all as specified and as directed by the Engineer-in-Charge. NOTE :- (i) The unit rate shall be included cost of small fittings such as elbow, socket, reducer, tee, union, etc. (ii) The whole process of reconnecting and refixing in position after cleaning/after carrying out water proofing treatment shall be done on the same day to ensure uninterrupted water supply to the occupant, if failing so, Rs. 200/– shall be deducted for each tank per day from the contractor due.

Supply and fixing , water storage tank, 1000 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including disconnecting and dismantling of existing water tanks and removing from site all as specified in SSR Part–I , complete all as specified and as directed by the Engineer-in-Charge. Note : - The colour of tanks shall be white colour .

Supply and fixing as in repair 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 15 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair, complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area exceeding 01 sqm but not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with prelaminated sheet and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of factory made solid PVC moulded door shutters with particle board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290-W (Gde E-165) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in holdfasts etc., complete all as specified and as directed by the Engineer-in-Charge.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

Supply and fixing of 150 mm long aluminium handle, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 200 mm long, aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 250mm long aluminium alloy, anodized, sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of butt hinges 100mm long of stainless steel, medium weight, complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate including welding or screwing to MS frame complete all as specified and directed.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified by the Engineer-in-Charge.

Supply and fixing of stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair stainless steel wire cloths 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (un–reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x450 x7mm or 300x 600x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic tiles light shade,1st quality,(square/ rectangular), 10mm thick, area of each tile exceeding 0.36 sqm and not exc 1.00 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vitrified ceramic double charged light shade tiles, 1st quality, of same description as of floor tiles in serial item No. 63 above but 100mm to 200mm height as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 8 to 10mm thick heavy duty (digital) vitrified coloured paver tiles of size 300mm x 300mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) , complete all as specified and as directed by the Engineer-in-Charge. Make: Endura of Johnson or Durastone of Somany or equivalent make given in App ‘B’

M&L cement concrete chequred tiles of size 300 x 300 mm x10 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete.all as specified and as directed by the Engr-in-Charge.

Material and labour for vibratory rubber moulded coloured precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, ISI marked of 60 mm thickness, grade M-35 with grey cement and pigments over and including a layer of sand cushioning, 25 mm thick complete all as specified and as directed by the Engineer-in-Charge.

M&L vitrified ceramic double charged light shade tiles 1st quality (square/rectengular), 10mm thick, area of each tile not exc 0.36 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L vitrified ceramic double charged light shade tiles 1st quality (square/rectengular), 10mm thick, of same description as of floor tiles in serial item No. 68 above but 150mm height as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 25 mm thick PCC 1:2:4, type B0 as in sub base of floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note- This item shall not be executed in the location, where dismantling of tiles only have been done.

Taking down eaves gutters and rainwater pipes (in any size in any position or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engr-in-Charge.

Supply and fixing 110mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed by the Engineer-in-Charge..(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified and directed.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534)

Supply and fixing of brass chromium plated wash hand basin mixer for mixing hot and cold water screwed down for 15mm dia pipe including waste popup with 450mm long braided hoses and all connecting fittings as in repair complete all as specified and as directed by the Engineer-in-Charge. Make:- Jaquar Cat part No.QQP-7167BPM/Cera Cat part No. F2007461 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of as in repair brass chromium plated concealed stop cock with long shank and wall flange screwed down,high pressure with crutch handle, screwed down both ends for iron pipe or for unions 15mm bore complete all as specified and as directed by the Engineer-in-Charge. Make:- Jaquar Cat part No.CON-083FTK or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass chromium plated wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115 mm long bend pipe, connecting legs and wall flange without hand and overhead shower as in repair complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No FLR-5267N or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass chromium plated soap dispenser with glass bottle as in repair complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of brass chromium plated Towel ring round including fixing with brass screws complete fixed complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1121BN or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass chromium plated Soap Dish Holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1131N or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of overhead shower 200mmx200mm square shape single flow ABS body chromium plated with grey face plate with rubit clean system as in repair complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of corner Glass shelf 300 mm (with brass bracket) including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of brass chromium plated hand shower ( health faucut) with 8 mm dia 1.2 mtr long flexible tube and wall hook with NRV ( back flow preventer )complete fixed to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ALD577 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of counter top vitreous china wash hand basin white with 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting, etc. as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : CERA Cat part No.S2020137 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of single piece water closet with PP soft close seat cover, hinges, fixing accessories and accessories set, cistern fittings, S or P Trap complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : CERA Cat part No.S1013209 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing of brass CP toilet paper holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-11535 or equivalent makes mentioned in list of make attached as Appendix ‘B’ of CA.

Supply and fixing in repair MS mortise lock suitable for aluminium/wooden door shutters , universal type,and weight between 250 to 500 grm complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repairs aluminium D type handle size 150 to 200mm and suitable for aluminium/wooden shutters complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of aluminium (Die-cast) body hydraulically door closer regulated, designation No.3, universal type, suitable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty as in repair complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for repairing of all type aluminium window/door shutter with frame and refixing it after re-securing its frame work by means of tightening with new screw ,cleats, rubber gasket and refixing in the same opening complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of powder coated aluminium section (minimum thickness of powder coating 50 micron) for chowkats, doors shutter comprising of the following section including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge:- (a) Door frame single groove 101.6mm x 44.45mm x 2.50mm thick (b) shutter top 47.62mm x 44.45mm x 1.95mm thick (c) shutter bottom 114.30mm x 44.45mm x 2.15mm thick (d) shutter vertical 85mm x 44.45mm x 1.80mm thick (e) shutter middle 83.5mm x 44.45mm x 2.40mm (f) Gauging clip weighing not less than 0.097Kg/matre Note : (a). Glazing/wire mesh shall be measured and paid separately; (b). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required. (c). The rates shall be inclusive of locking arrangement with mortice lock of brass, vertical type,100mm size, 4 lever, ISI marked with duplicate keys and handle including complete packing with silicon gel all round contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

S& F in repairs aluminium frame and shutter for doors, sliding windows & ventilators (moveable louvers type) with one or more rebates including joining cleat for fixing ctc rubber gasketing all round the panels/shutter to fix glass, PVC gasketing in all channels, locking arrangement, complete all as specified. Note: (a) Glass/ mesh/XPM to be measured and paid under respective item of work. (b) The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminiumframework and wall. (c) The rates quoted shall be inclusive of neoprene beading, glazing clips, screws, etc as required which shall not be measured for arriving the weight.

S&F side hung openable/sliding type without sash bar, window, ventilator shutter having double shutter i.e glazed & wire gauge shutter made from powder coated aluminium section (minimum thickness of powder coating 50 micron) comprising of the following sections, including the cost of EPDM rubber/ neoprene gasket required with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge:- (a) Window frame 101.6mm x 44.45mm x 2.10mm thick (b) Window shutter top bottom and sides 47.62mm x 44.45mm x 1.95mm thick (c) Mullion 53mm x 52mm x 2.00mm thick (d) Glazing clip weighing not less than 0.097Kg/matre Note : (a ) Powder coated aluminium fittings such as peg stays 150mm long (1 No.), hinges type C-21, 75mm long (2 No.), suitable handle (1 No.) per leaf shall be provided and cost of the same shall be deemed to be included in quoted rates. (b) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (c). Glazing/wire mesh shall be measured and paid separately; (d). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required. (e). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Supply and fix 12 mm thick prelaminated particale board,interior grade, prelaminated both side with decorative choice lamination and fixed to aluminium door with glazing clips, rubber gasket etc complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 04mm thick frosted sheet glass ordinary type and glazing with aluminium beading, rubber packing in square n exc 0.5 sqm each pane complete all as specified and directed.

S & F aluminium powder coated Grill (DECO grill, DG 103 of7.5 mm thick of M/s ELESAR, M/S Royal Grill, M/S National Grill Associated Profiles & Aluminium Ltd.) fixed with suitable 'F' section(No. 8584)15.30 x 23.40 x 1.40mm(minimum), fabricated and riveted to aluminium windows/ventilator complete all as specified and directed.

Supply and fixing of EPDM rubber/ neoprene gasket in glass pane from existing aluminium windows/ventilators/doors including taking down old/defective neoprene gasket complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness including cover fillets and false ceiling frame work of any size/ description complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of boarding of any description and in any position of any size complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 18/19mm thick block boards,for cup board shutters etc., grade 2 quality, interior grade, commercial type fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 6mm thick (3 ply) plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge

Material and labour for 4mm thick (3 ply) veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing of GI Metal Suspended ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, and as directed by Engineer-in-charge. GI Metal Ceiling laying perforated Tengular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fibre acoustical fleece. Note- Ceiling tiles and ceiling grid shall be of the same make.

Supply and fixing 5-8mm thick solid/ Hollow profile designer PVC paneling with panel of width 250mm to 300mm fixed to wall/ceiling with screw and rawel plug including PVC beading (U,L section) wherever required.complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 8-10mm thick flute profile designer PVC paneling with panel of width 250mm to 300mm fixed to wall/ceiling with screw and rawel plug including PVC beading (U,L section) wherever required.complete all as specified and as directed by the Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of timber scantlings 40 sq cm and over in section, in any position, unframed work complete all as specified and directed by the Engineer-in-Charge.

Supply and Fixing mild steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 complete all as specified and as directed.

S&F pre–painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick, having zinc coating 150 gm per sqm (Az–150) of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer–in–Charge.

S&F pre–painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, having zinc coating 150 gm per sqm (Az–150) as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer–in–Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white lime wash on prepared surfaces of ceiling etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of acrylic distemper with painting roller over prepared surfaces of ceiling etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of acrylic distemper with painting roller over prepared surfaces of walls pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge.

Material and labour complete removal of existing treatment from wall by scrappers or any other means and washing , rubbing down and stopping and applying two coats of acrylic distemper with painting roller over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for complete removal of existing treatment from wall by scrappers or any other means and washing , rubbing down and stopping applying two coats of acrylic distemper over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, of walls of any description using painting roller after preparation of brick/concrete, plastered / unplastered surfaces of walls complete all as specified and as directed by Engineer-in charge .

Material and labour complete removal of existing treatment from wall by scrappers or any other means and washing , rubbing down and stopping applying two coats of plastic emulsion on interior surface over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, of walls of any description using painting roller after preparation of brick/concrete, plastered / unplastered surfaces of walls complete all as specified and as directed by Engineer-in charge .

Material and labour preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior grade paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on the wall, pillars, cornices etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of cement base paint on the wall, pillars, cornices etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Material and labour preparation of old decorated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Schedule 'A' Part-II (E/M itmes) Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc., complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description all as per serial item No.127 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.127 here-in-before but for one socket outlet 6 Amp with 1.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 1.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Point wiring shall be done in a manner that not more than 04 socket point executed in one circuit. (ii) Each socket point will be measured and paid as per point.

Description all as per serial item No.127 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Point wiring shall be done in a manner that not more than 02 socket point executed in one circuit. (ii) Each socket point will be measured and paid as per point.

Description all as per srl item No 127 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Point wiring shall be done in a manner that not more than 01 socket point executed in one circuit. (ii) Each socket point will be measured and paid as per point.

Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of modular socket outlet multipin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet multipin combined, (6pin), 16 Amps, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing as in repair electronic Fan regulator, modular 100 watts, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep, complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair calling bell, ding dong, 230 volt, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair, LED batten fitting 10-12 watts, 2 feet, aluminium housing with electronic driver cool/warm type industrial model complete, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LUMILINE+ BS10WLED865SPCSS of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair LED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic driver cool/warm type industrial model complete, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LUMILINE+ BS20WLED865SPCSS of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair, LED surface mounted bulk head luminaries, 8-10 watts, with min 800 lumen, industrial model, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. HEXAFT10WLED857SSYMBOPC of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair, 9/12 watt LED light fitting heritage wall mounting fixture (sketch type) including B-22 LED lamp compact and energy efficient epoxy powder coated luminaire and connecting with copper conductor flexible cable from ceiling rose to connector of the light complete including removing unserviceable light fittings complete all as specified and as directed by the Engineer-in-Charge. Cat part No. HLWB-01-B22 of make Halonix or equivalent in make given in Appx 'B'.

Supply and fixing recess mounting LED 15/18 watt cool/warm type circular down lighter/ COB panel with PVC housing, 240 volt, 50HZ, AC supply complete with all accessories internally pre wired including connecting with 3 core flexible copper conductor from ceiling rose to connector of the light, including disconnecting and taking down existing old unserviceable fitting complete all as specified and as directed by the Engr-in-charge. Cat part No.EDGEPRONEORDDLR15WLED840S of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing recess mounting LED 5/8 watt cool/warm type circular down lighter/ COB panel with PVC housing, 240 volt, 50HZ, AC supply complete with all accessories internally pre wired including connecting with 3 core flexible copper conductor from ceiling rose to connector of the light, including disconnecting and taking down existing old unserviceable fitting complete all as specified and as directed by the Engr-in-charge. Cat part No. INTEGRAHEDLR7WLED857S of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing LED flat panel 2' x 2' size fully difused surface/ recess mounted fitting (grid/ gypsum type) 36-40 watt , 5700K, warm/cool white with powder coating and CRCA front cover including frame with provision of PVC flexible copper conductor cable from ceiling rose to light fitting as in repair complete all as specified and as directed by the Engr-in-charge. Cat part No.VENUSNEO2X2PLR36WLED857G2 of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair, LED Bldg Security Light Fittings of capacity 35 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection including service bracket of mild steel pipe 25 mm bore medium grade of length 0.70 mtr fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts and washer and suitable reducer for connecting fitting to GI pipeand other connected accessories & making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA 'B' curve including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811955 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fixing MCB SP, 6-32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge. Cat part No 811008 to 811015 of make Indoasian or equivalent make given in Appx 'B'.

Supply and fixing MCB SPN 32 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge.Cat part No 811035 of make Indoasian or equivalent make given in Appx 'B'.

Supply and fixing MCB SPN, 63 Amps, 240 volt,10 KA , 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge. Cat part No 811037 of make Indoasian or equivalent make given in Appx 'B'.

Supply and fixing sheet metal MCB DB SPN 12 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811828 of make Indo Asian or equivalent make given in Appx 'B'.

Supply and fixing sheet metal enclosure Vertical triple pole & neutral(VTPN) IP-54 including MCCB 100 Amp, 16 KA, 415 volts, 8 way with 400 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection including making smooth the disturbed surface including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No. 812047 + 830097 of make Indo Asian or equivalent make given in Appx 'B'.

Supply and fixing sheet metal enclosure triple pole & neutral(TPN) IP-54 including MCB 63 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection including making smooth the disturbed surface including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811856 of make Indo Asian or equivalent make given in Appx 'B'.

Supply and fixing sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811826 of make Indo Asian or equivalent make given in Appx 'B'.

Supply and laying as in repair sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Supply and laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Supply and laying as in repair sub main wiring with two run of 10 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Supply and laying as in repair sub main wiring with four run of 10 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 10 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Four runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Material and labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test point as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing as in repair complete all as directed by Engineer-in-Charge and earth testing on completion.

Supply and fixing as in repair of heavy duty exhaust fan 250mm sweep with corrosion resistant PVC body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, PVC base frame with rubber mountings for silent operation, maximum watt input not more than 25 watt, 1400 RPM, minimum air delivery 210 cum/hr, PVC blades and shutter type louvers self-openable/ close able for protecting the entrance of birds and testing as in repair complete all as specified and as directed by Engineer-in-Charge. Cat part No 70049 of make Bajaj or equivalent make given in Appx 'B'.

Supply and fixing as in repair heavy duty wall mounting fan 400 mm sweep with corrosion resistant PVC body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, rigid frame , 1350 RPM, PVC blades and testing complete all as specified and as directed by Engineer-in-Charge. Cat part No 250552 of make Bajaj or equivalent make given in Appx 'B'.

Note:- Amount of credit of Rs.65,132.00 for retrieved materials is mentioned in Schedule of Credit Page No..123 & 124. of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/S Gurpreet Singh (BID ID -3353810)

M/S VINOD RANA CONTRACTOR (BID ID -3355274)

KULWANT SINGH (BID ID -3356210)

SONDHI CONSTRUCTION (BID ID -3356548)

M/s Kang Builders (BID ID -3356720)

dhingra builders (BID ID -3363805)