Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹45.9 L
EMD Value
₹46,000
Closing Date
19 Nov 2026, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer Panchayat R&B Division Bharuch
Construction of Atalwadi with Toilet Block (Gents & Ladies), Kitchen & Solar Roof Top at village Tralsa Tal. Bharuch Dist. Bharuch
361428
16/2026-27
Open
Civil - All
Fixed-rate
Bharuch
5 documents required · 5 mandatory
₹1,500
Executive Engineer Panchayat R&B Division Bharuch
₹46,000
4 Nov 2026
4 Nov 2026
4 Nov 2026
19 Nov 2026
4 Nov 2026
90 days
No. Figure Amount
1 Excavation for foundation upto 1.50 mt depth including sorting out and 97.70 Cum 203.83
stacking of useful materials and disposing the excavated stuff for all lead and
lift for loose or soft soil.
2 Excavation for foundation upto 1.50 mt depth including sorting out and 79.40 Cum 214.59
stacking of useful materials and disposing the excavated stuff for all lead and
lift for dense or hard soil.
3 Providing and laying cement concrete 1:4:8 (1 cement : 4coarse sand : 8 84.60 Cum 2719.20
machine crushed stone aggregates 40 mm. nominal size) and curing complete
excluding cost of form work in foundation and plinth.
4 Providing and laying cement concrete 1:1.5:3 (1 cement, 1.5 sand, 3 graded 21.08 Cum 4996.22
stone aggregates 20 mm nominal size) and curing complete excluding cost of
form work and reinforcement for reinforced cement concrete work in (C)
Columns, pillars, posts, struts up to floor two level.
5 Providing and laying brick work using common burnt clay building conventional 43.80 Cum 4539.94
type bricks having crushing strength not less than 35 Kg./Sq.cm. in foundation
and plinth in cement mortar 1:5 (1 cement : 5 fine sand) including the cost of
all materials and labour charges etc. complete.
6 Providing and laying cement concrete 1:1.5:3 (1 cement, 1.5 sand, 3 graded 11.60 Cum 5988.16
stone aggregates 20 mm nominal size) and curing complete including the cost
of form work (A) Foundation and plinth.
7 Filling available excavated earth (excluding rock) in trenches plinth side of 171.25 Cum 130.39
foundation etc. in layer not exceeding 20 cm in depth consolidation each
deposited layer by ramming and watering etc. complete.
8 Providing and laying brick work using common burnt clay building conventional 75.12 Cum 4078.17
type bricks having crushing strength not less than 35 Kg/sq.cm. in super
structure upto floor two level in cement mortar 1:6 (1 cement : 6 fine sand) for
Ground Floor including the cost of all materials and labour charges etc.
9 Providing and laying ordinary cement concrete 1:1.5:3 (1 cement, 1.5 coarse 2.30 Cum 10687.60
sand, 3 graded stone aggregates 20 mm nominal size) for R.C.C. LINTELS
including finishing smooth with curing of form work but excluding the cost of
reinforcement for above floor two level.
10 Providing 15mm thick cement plaster in single coat on rough (similar) side of 838.00 Sq.m. 187.71
single or half brick walls for interior plastering upto floor two level and finished
even and smooth in cement mortar 1:3 (1 cement : 3 sand)
11 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement for R.C.C. work 7205.00 Kg. 76.21
including bending, binding and placing in position complete upto all floor level
for all floors.
12 Steel work, riveted in built up sections framed work including cutting, hoisting, 117.53 Qtl. 5818.65
fixing in position and applying a priming coat of red lead paint (A) In beams
and joists, channels angles Tees, flats, with connecting plates or angle cleats
as in main and cross beams. Hip and jack rafters, purlins connected to
common rafters and the like.
13 Finishing wall with weather proof exterior emulsion paint on wall surface (two 588.00 Sq.m. 114.53
coats) to give an required shape even shade after thoroughly brushing surface
to remove all dirt, dust and remains of loose powdered materials etc. complete.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
14 Providing corrugated G.I. sheet of class-3 roofing fixed with galvanized iron J 759.00 Sq.m. 727.13
or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washer
filled with white lead complete including ridges, gutters etc. excluding the cost
of purlins, rafters and trusses. (1) 0.80 mm thick sheet.
15 Providing and fixing 150mm wide 450mm over all semicircular plain G.I. sheet 57.60 Sq.m. 561.27
class-3 gutter with Iron brackets 40mm x 3mm size bolts, nuts, washers etc.
including making necessary connection with rain water pipes. (i) 0.80 mm thick
16 Providing and laying polished Kota stone slab flooring over 20mm (average) 516.70 Sq.m. 976.72
thick base of cement mortar 1:6 (1 cement : 6 coarse sand) or L.M. 1.1.5 (1-
Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry
mixed with pigment to match the shade of slab including rubbing and polishing
etc. complete. (A) 25mm thick.
17 Providing and laying brick work using common burnt clay building conventional 48.28 Cum 4021.02
type bricks having crushing strength not less than 35 Kg./Sq.cm. in foundation
and plinth in cement mortar 1:6 (1 cement : 6 fine sand) including the cost of
all materials and labour charges etc. complete.
18 Providing and laying ordinary cement concrete M-200 (1 cement, 1 1/2 coarse 10.50 Cum 5850.70
sand, 3 graded stone aggregate of 20mm nominal size) work with curing etc.
complete including the cost of form work but excluding the cost of
reinforcement for R.C.C. work in SLAB having more than 10cm. and end upto
13cm. thickness up to floor two level.
19 Providing and fixing window having extruded aluminum colour anodized 7.40 Sq.m. 1713.70
section frame main outer size 63.50 x 38.10 x 1.95 mm (@ Wt 1.094 Kg /
Rmt), horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm (@
wt.of 0.695 Kg/mt), vertical member of size 61.85 mm x 31.75mm x 1.30 mm
(@ wt.of 0.659 Kg/mt) with sliding shutters of horizontal member size 40mm x
18mm x 1.29mm (@ wt. of 0.456 Kg/mt), vertical member of size 40mm x
18mm x 1.29mm (@ wt. of 0.456 Kg/mt. & @ Wt. 0.457 Kg/mt) with 5 mm
thick transparent bronze colour tinted float glass with powder coated aluminum
fittings and fixtures and transparent silicon sealant glass fixing to frame as per
details etc. complete for window.
20 Providing and fixing 30mm thick FACTORY MADE SOLID PANEL PVC DOOR 25.20 Sq.m. 1146.37
SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness
and size of 19mm x 19mm for stiles and 15mm x 15 mm for top and bottom
rails. M.S. frame shall have a coat of steel primers of approved make and
manufacture, M.S. frame shall be covered with 5 mm thick heat moulded PVC
'C' channel of size 30 x 50 mm forming stiles, and 5mm thick 75mm wide PVC
sheets for top rail, lock rail and bottom rail on either side, and 10mm (5mm x
2) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom rail,
Panelling of 5 stiles and rails with 30mm wide x 5mm thick PVC sheet beading
on either side and joined together with solvent cement adhesive. An additional
5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'c'
channel using PVC solvent cement adhesive etc. complete as per direction of
Engineer in charge, manufacture's specification and drawing.
21 Providing and fixing wash down water closet European type W.C. pan with 12.00 No. 1975.70
integral P or S trap including jointing the trap with soil pipe in cement mortar
1:1 (1 cement : 1 fine sand) seat and cover to be measured and paid for
separately. (A) Vitreous china pattern - I (i) white colour including 32mm dia.
flush pipe connected with W.C. & Seat cover & nozzle spray.
22 Providing and fixing wash basin with single hole for pillars tap with C.I. or M.S. 4.00 No. 2075.40
brackets painted white including cutting holes and making good the same
including fixing M.I. fisher union of 40 mm dia., C.P. brass waste of 40 mm dia,
15 dia pillar tap and brass screw down stop tap of 15 mm dia etc. complete.
(A) Vitreous china (ii) flat back wash basin 550 mm x 400 mm size in white
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
23 Providing and fixing PVC SWR Nahni trap IS-14735 for drain - 100 mm 18.00 No. 558.36
diameter with jali of the following nominal diameter of self cleaning design with
C.I. screwed down or hinged grating including the cost of cutting and making
good the walls.
24 Proving and fixing cast iron spigot and socket soil, waste and ventilating pipe 26.00 No. 890.46
soft the following nominal size. (C) 100mm dia.
25 Providing and fixing in position cowl vent to pipes (C) 100mm. dia. as directed. 3.00 No. 501.87
26 Providing and fixing S.W. Gully trap with C.I. grating brick masonry chamber 10.00 No. 1292.19
and water tight C.I. cover with frame of 300 x 300 mm size (inside) with
standard weight (i) square mouth traps (A) 100 mm x 100 mm size P type.
27 Constructing brick masonry road gully chamber 450 mm x 450 mm x 775 mm 3.00 No. 958.17
with vertical grating complete with C.l. Manhole cover 450 x 600 mm size
28 Providing, erecting and fixing double coated PVC (ISI) mark water tank of 2500.00 Litre 3.95
required capacity each with all necessary fittings and connection etc. complete
on terrace as directed.
29 Proving sock pit of 5.0 Cumt. Volume including excavating and filling brick bats 3.00 No. 3372.19
with dry masonary work at top for 45 cm. height including covering the top with
stone including providing vatas in C.M. 1:3 with finishing, curing etc. complete
as directed.
30 Providing, laying and jointing in true line and level I.S.I. mark 110mm diameter 46.00 Rmt. 835.15
U.P.V.C. SWR Type B pipe confirming to IS 13592 -1992 with one end plain
and other end socketed with rubbering & fitting confirming to ISI 14735-1999
of approved make for drainage system pipe line, pipe shall be jointed with
each other with rubber lubricant, pipe shall be fixed on wall using of PVC
clamp of the size 110mm diameter x 149mm length x 145mm high at every
2000mm center to center or shall be concealed in wall as directed including
necessary fitting such as bends, shoes etc. including testing of pipe and joints
and jointed with adhesive solvent cement including cost of all materials.
31 Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes 32.00 Rmt. 397.87
(Medium grade) of the following nominal bore, tube fitting and clamps
including making good the wall ceiling and floor. (C) 25mm
32 Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes 30.00 Rmt. 244.98
(Medium grade) of the following nominal bore, tube fitting and clamps
including making good the wall ceiling and floor. (A) 15mm
33 Providing and fixing screw down bib taps of following size (A) Brass screw 23.00 No. 186.83
down bib tap polished bright (i) 15mm dia. as approved by Engineer in charge.
34 Providing and laying Ceramic tiles 8mm thick in flooring treads of steps and 150.20 Sq.m. 957.63
landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse
sand) finishing with flush pointing in white cement.
35 Excavation for foundation upto 1.5 m depth including sorting out and stacking 19.17 Cum 375.94
of useful materials and disposing off the excavated stuff upto 50 Meter lead.
(C) Hard Murrum
36 Providing and laying ordinary cement concrete 1:1.5:3 (1 cement, 1.5 sand, 3 3.56 Cum 8353.26
graded stone aggregates 20 mm nominal size) including finishing smooth and
curing complete, excluding the cost of formwork and reinforcement for RCC
work in foundations, footings, bases of columns and mass concrete.
37 Providing and laying C.C. 1:1.5:3 (1 cement, 1.5 course sand, 3 graded stone 6.65 Cum 8035.64
aggregate of 20 mm nominal size) and finishing smooth with curing etc.
complete including the cost of formwork but excl. the cost of reinforcement for
R.C.C. work in. (A) Beam having cross sectional area 0.085 to 0.12 Sqm.upto
floor two level.
thickness including watering, ramming and consolidating etc. complete.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
39 Providing and laying cement concrete 1:1.5:3 (1cement,1.5 sand, 3 graded 0.30 Cum 6748.26
stone aggregates 20 mm nominal size) and curing complete, including cost of
formwork in sill and sides (R.C.C. band) but excluding the cost of
reinforcement upto floor two level
40 Providing and laying cement concrete 1:1.5:3 (1 cement, 1.5 coarse sand, 3 0.60 Cum 6705.35
graded stone aggregate of 20 mm nominal size) for reinforcement concrete
CHHAJJAS not exceeding 10cm. thickness upto floor two level including
finishing the exposed surface with C.M. 1:3 (1 cement, 3 fine sand) to give a
smooth and even surface, centering, formwork and curing complete excluding
the cost of reinforcement above plinth upto floor two level.
41 Providing 20 mm thick sand faced cement plaster on walls upto heights 10 126.70 Sq.m. 329.29
meters above ground level consisting of 12mm thick backing coat of cement
mortar 1:3 (1 cement : 3 sand) and 8mm thick finishing coat of C.M. 1:1 (1
cement : 1 sand) etc. complete.
42 Providing 10 mm thick cement plaster in single coat on fair side of brick / 56.30 Sq.m. 188.37
concrete walls for interior plastering upto floor two level and finished even and
smooth in cement mortar 1:3 (1 cement : 3 sand) upto floor two level finished
even & smooth with floating coat of neat cement slurry.
43 Providing 10 mm thick cement plaster in single coat on fair side of brick / 31.00 Sq.m. 164.97
concrete walls for interior plastering upto floor two level and finished even and
smooth in cement mortar 1:3 (1 cement : 3 sand) for plastering on ceilings and
soffits of stairs upto floor two level instead of plastering on walls.
44 Wall painting (two coats) with plastic emulsion paint of approved brand and 56.30 Sq.m. 119.49
manufacture on undecorated wall surfaces to give an even shade including
thoroughly brushing the surface free from mortar droppings and other foreign
matter and sand papered smooth including applying two coats of Birla or Asian
acrylic lappy (putty) and two coats of primer of approved brand and
manufacture on new wall surface to give an even shade.
45 Ceiling painting (two coats) with plastic emulsion paint of approved brand and 45.00 Sq.m. 124.76
manufacture on undecorated wall surfaces to give an even shade including
thoroughly brushing the surface free from mortar droppings and other foreign
matter and sand papered smooth including applying two coats of Birla or Asian
acrylic lappy (putty) and two coats of primer of approved brand and
manufacture on new wall surface to give an even shade.
46 Providing and laying 24" x 24" vitrified 8 mm thick tile flooring over 20 mm 39.00 Sq.m. 1415.77
(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new
surface or fixing on existing flooring by adhesive material including
dismentaling of existing flooring and jointed with color cement slurry including
finished with flush pointing & cleaning the surface etc. complete for light shade.
47 Providing and laying Green marble (18 mm thick) in jambs & sills of windows 5.70 Sq.m. 1648.73
and pillars laid on 10 mm thick cement mortar 1:3 (using Sulphate resistant
cement) (1 cement : 3 coarse sand) laid and jointed with grey cement slurry
including rubbing and polishing complete.
48 Providing and fixing 35 mm thick panelled, glazed or panelled and glazed 2.50 Sq.m. 3744.46
shutters for doors, windows and clearstory windows including anodised
alluminium butt hinges with necessary screws and Indian teak wood shutters
with (B) Partical board panells. 12mm. thick including applying primer and two
coats of oil painting etc. complete.
49 Providing and fixing M.S. grills of required pattern to wooden frames of 86.40 Kg. 154.62
windows etc. with M.S. flats at required spacings and frame alround, square or
round bars with round headed bolts and nuts or by screws. (B) ORNAMENTAL
50 Constructing a cooking platform 60 cm. width and 70 cm high resting on B.B. 8.00 Rmt. 2694.77
Masonry walls 23 cm.thick in C.M.(1:6) with (i) Fixing or precast R.C.C. 1:2:4)
8 cm. thick slab with marble chips set in C.M. (1:6) (6mm thick terrazo) with
plastering on exposed faces walls in C.M. (1:4) etc. complete.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
51 Providing & fixing Marble Takti of size 60cm x 45 m. including carving & 1.00 No. 2525.00
painting the letters related to scheme & year as directed.
52 Providing, Supplying, Installing, Testing & Commissioning of 3.2 kW Grid 1.00 No. 163806.00
Connected Roof top Solar PV Power Plant on existing shed structure.
TOTAL Rs.
i.e. Rs. Fourty Five lacs Ninety Three thousand Three hundred Eighty Five and Twenty Two paisa only.
I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written
in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.
Estimated amount put to tender Estimated amount put to tender
Deduct………% below Add………% Above
Net Rs. ___________________________ Total Rs. ________________________
In words ____________________ In words ____________________
1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-
Charge for which no extra payment shall be made.
2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.
3. GST and Income tax TDS will be deducted at a source while making payments of bills.
4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-
10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there
is a change as per actual mix design the cost of difference of cement consumption have been deducted from the
rate of original item at the rate of input rate mentioned in all the tender.
5. The Contractor will have to submit the all required mix design at his own cost before execution as
directed and to be approved from the Engineer in charge.
Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and
found order.
Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer
Panchayat (R & B) Sub Division, Panchayat (R & B) Division, Panchayat (R & B) Division,
Bharuch Bharuch Bharuch
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
GRs_BHARUCH.pdf
Specification Index.pdf
Technical Specifications.pdf
BOQ_ATALWADI_2026-27_TRALSA.pdf
SBD_ATALWADI_2026-27_TRALSA.pdf
NIT_ATALWADI_2026-27_TRALSA.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .