Provn of security lights and Augmentation of centralised oxygen gas pipe line system at Yol Cantt

Amount

Supply and Fix Steel tubular swaged poles complete with base plate 8mm thick welded with pole, finial taper plug, bolt, nut and screws as specified type 410 SP-31 (9m long) including one coat of red-oxide zinc chrome primer and two coats of aluminium paint on surfaces exposed to view and making 30cm wide strips (total 5 Nos) with white and black paint alternately on external surface above PCC benching including numbering with black paint and painting with bituminous paint internally complete and externally for portion embedded in PCC including dismantling of old unsv any type of poles any length, complete all as specified and directed. Note : Excavation & earth work and PCC shall be measrued and paid separately.

Supply and Fix Steel tubular swaged poles complete with base plate 8mm thick welded with pole, finial taper plug, bolt, nut and screws as specified type 410 SP-31 (11m long) including one coat of red-oxide zinc chrome primer and two coats of aluminium paint on surfaces exposed to view and making 30cm wide strips (total 5 Nos) with white and black paint alternately on external surface above PCC benching including numbering with black paint and painting with bituminous paint internally complete and externally for portion embedded in PCC including dismantling of old unsv any type of poles any length, complete all as specified and directed. Note : Excavation & earth work and PCC shall be measrued and paid separately.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm 4 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying complete all as specified.

Supply and fix pole junction box sheet moulded compounded (SMC) type with hinged door and locking arrangement of size 200x140x95mm internal comprising one No SP MCB 6 Amps capactiy and one No bakelite based buetral link one No earthing terminal and Four Nos aluminium bus bar of suitable capacity including nuts, bolts, MS clamp etc. complete. Make- Sintex model No GS-JB-2014 or

S&F copper conductor cable PVC insulated single core 2.5 Sqmm (two run for Phase & Neutral) and single run 1.5 Sqmm copper conductor cable for earth wire (Green Colour) through and incl PVC conduit 20mm dia as per site requirment from junction box to street light, complete all as specified and directed.

Supply & fixing Flood light fitting LED 150 Watt (6000 K) with External SPD 10KV. Make: Havells JETAADORNFLS150WLED757SSYMTOTG Bajaj/ Crompton/ Philips

Supply & fixing Security light fitting LED 100 Watt (6000 K) with External SPD 10KV. Make: Havells ENDURAPEARLPLUSSL100WLED757PASYTOPCLC Bajaj/ Crompton/ Philips

Supply & fixing Security light fitting LED 60 Watt (6000 K) with External SPD 10KV. Make: Havells/ Bajaj/ Crompton/ Philips

Supply and fix GI Bracket made of 40mm dia GI pipe medium geade 1.5 mtr long suitable for street light for steel / RCC pole as per site requirement including suitable nut, bolt, washers and clamps complete accesseries all as specified and directed.

Excavation in trenches n.exc 1.5 metres wide and n.exc 1.5 metres deep and getting out in any type of soil, all as specified.

Excavation in trenches n.exc 1.5 metres wide and exc 1.5 metres and not exc 3 metres deep and getting out in any type of soil, all as specified.

Returning filling in including spreading leveling, watering and well ramming in layers n. exc 25cm, all as specified.

Removal of excavated material to be distance n.exc 50M and depositing where directed at a level n.exc 1.5m high from the starting point, all as specified.

Sand cushioning to under ground cables, 8 cm thick layer before laying and testing the cable and 15 cm thick after laying and directed by Engr-in-Charge.

Supply and laying Sub class ‘B’ bricks for covering to cable protection with width equal to the length of bricks complete all as specified and as directed.

Plain cement concrete M-10 nominal mix, type C-1 using 20mm graded crushed stone aggregate as in Bedding of pole including necessary form work, complete all as specified.

Plain cement concrete M-7.5 nominal mix, type D-2 using 40mm graded crushed stone aggregate as in plint protection of poles, stays etc. as mass concrete, complete all as specified directed by Engr-in-Charge..

Plain cement concrete M-15 nominal mix, type B-1 using 20mm graded crushed stone aggregate as in coping of pole including necessary form work, complete all as specified directed by Engr-in-Charge.

GI light grade pipe of 50mm dia with all fitting; laid in trenches, across road or pole complete all as specified.

Structural steel work as in cross arms, bracings, supports, clamp and back plate fabricated from steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated and applying two coats of aluminium paint over one coat of red oxide zinc chrome primer including preparation of surfaces and dismantling old structural steel work in cross arms and stacking at site, complete all as specified & directed.

S&F Copper Pipe : Copper tube of soiled drawn seamless deoxidized, non-arsenical, half hard, tempered and degreased as per BS EN 13348:2001 duly supported with manufacturer test certificates for physical properties and chemical composition. MAKE:- MAXFLOW, RAJCO, MANDEV

(a) 12mmx0.9mm

(b) 15 mm x0.9mm

S&F of GASTERMINAL UNIT : CE MARKED Terminal Units (Gas Outlets) with adaptors/probe for oxygen, compressed air and vacuum: Matching adaptors to the gas outlet mentioned above i.e. adaptor for oxygen, air and vacuum. The terminal units would have following features. a. It would be front insertion type. b. Terminal unit would have mechanism with check valve. C. Allow single hand operation. D. On first insertion of probe the probe shall sit in a standby position. At the stage there shall be no gas flow. E. Only on pressing the probe second time, the gas supply would start. F. They would close automatically when connected apparatus is removed. G. For allowing on line maintenance the terminal unit would be equipped with a check valve for all positive pressure gases for closing gas supply whenever the outlet point is opened. H. The outlet would be non interchangeable for specific gas and it would accept only correct medical gas adopter/Probe. I. It would be color coded as per HTM 2022. J. The design of this outlet would be compatible to installed vertical on valve horizontally on ICCU panel and area servicing unit and also vertical to fit in pendants. K. It would only supply with correct probe/ adopter.

S&F of ISOLATION VALVES ISO 9001-2008 SPECIFICATION: To control the pressure as well as for maintenance quarter turn open at 90-degree ball type valves would be provided. These valves would be of nickel-plated brass body having PTFE seat and inner outer seals. These valves would have stainless steel ball of specific ID clearance so that line pressure would not drop. For installation only PTFE gaskets would be used in between nuts and valve to prevent leakage. All the nuts for fixing the ball valve would be of brass with brass nozzles for easily brazing with copper tube. All ball valve assemblies would be on approachable height for easily operation. MAKE:- RB/RN/ELEMS/SMI/JSI/RK

S&F of BPC Flowmeter with humidifier bottle CE MARKED -: would be BPC single type Pipeline Flow Meter unit duly fitted with the fine adjustment valve. It would be backpressure compensated to bear and control the Oxygen Pressure approx. 60psi. Flow meter unit would be consisting of double wall rotta-meter has range of flow 0 to 13 ltrs per minute with fine adjustment valve. The rotta meter and humidifier bottle would be made of clear, impact resistance polycarbonate (duly graduated). This unit would be have attachment to fit humidifier bottle of capacity 100 ML. consist of clear, impact resistance polycarbonate jar. This would also have Reciprocating on top for flow meter/plastic cap having nozzles for outlet tubes and the inlet tube end would be multi function combination bubblier/ nebulizer to add the humidity and create an aerosol in Medical Gas min marks would be on jar. MAKE:- S.KUMAR/ AKTIVE/PMP/ GLOBAL MEDITECH/ SJK

S&F of Oxygen Base Unit. . (A) Oxygen Manifold 2+ 2 CE MARKED. . The oxygen manifold would be of above size of bulk oxygen cylinders. It is suitable to with stand a pressure of 2400 PSI. The main frame are made out of 50 X 50 X 6 mm angle iron and bottom frame of 20 X 20 mm ms square are install in such a way that the cylinders must be stage for use in upright position and are not fell down under any circumstances. The gases passed through inter-connecting tail pipes duly fitted with suitable bull nose and nut adopter for cylinder valve and tube size is 10mm OD Copper tube duly annealed having wall thickness 1.5mm in spiral shape and the other end of the tail pipe are fixed with non-return valve. The non return valve are fixed in brass block of size 25mm square vertically which are fitted with high pressure copper tube of size 15mm OD having wall thickness 1.5mm. Both the arms of manifold further fixed in automatic control panel. All the joints of copper tube, brass block, and inter connecting tubes are welded with silver brazing. Pressure release safety valve also provided. The manifold is fabricated in such a way to give distribution flow of 1500 ltrs per minute. The manifold would be degreased and purged with inert gas before commissioning.The manifold would be enamel painted as per color code. All above work would be done strictly as per specification and entire satisfaction of engineer in-charge.

S&F of BHP (Bed head panel CE MARKED :- 3 ft long made out of 1.6 laminated aluminium sheet die pressed in such a shape that looks good as per requirement.The modular medical turn king system/bed head panel: would be fabricated of aluminous die pressed 1.6 mm thick imported laminated sheet in such a way to provide 100% safe and efficient means to deliver all the gases as well as electrical to the patient/staff in intensive care conditions. To enclosed all piping, electrical wires, monitor wire ect it would be also 6AMP ELECTRIC SOCKET fitted continuously running on wall The design of modular BHU would consist of aluminum section to meet the requirement of HTM 2002, NFPA and other international standard. There would be no sharp edges having smooth finish and without any visible Reciprocatings etc.It would be have ability fix medical gas outlets, electrical sockets, 4 NO.S it would be fitted with.

M/S SATPAL & BROTHERS