Construction of Food Court at DD Puram in Bareilly

Amount

COSTING FOR FOOD COURT AT DD PURAM

12.1 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever require 12.1.3 0.63 mm thick with zinc coating not less than 275 gm/m² (For Wall)

12.1 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever require 12.1.3 0.63 mm thick with zinc coating not less than 275 gm/m² (For Ceiling)

R.C.C. work with cement apprved coarse sand and 2 cm (3/4)" gauge approved stone ballast in the proportion of 1:1.5:3 in slab excluding supply of reinforcement and its binding but including Necessary centering and shuttering etc. and also including supply of all materials, labour and T&P etc. required for proper completion of the work. Binding wire cosr being included in the item.

Mild steel or iron in plain work such as reinforceded concrete or reinforced brickwork ( when not included in an over all rates ) wrought to required shape as necessary inculidng bending for proper completion of the work and including supply of all steel and watsage and overlap and hooks .

First class brickwork in 1:6 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work As in item No.303 but in the proportion of 1:5 cement and coarse sand ROOM/TOILET

First class brickwork in 1:6 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work As in item No.303 but in the proportion of 1:5 cement and coarse sand BELOW SEATING & EATING TABLE

First class brickwork in 1:6 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work As in item No.303 but in the proportion of 1:5 cement and coarse sand BRICK WORK IN PLANTER

Mild steel or iron work in heavy sizes such as trusses;builts up gates, door, frames, records racks roof work, gates etc. brought to requirde from including drillng holes, rivetting or welding where necessary, and also including supply of steel, bolts, nuts etc.& their fixing required for proper completion of the work.

Mild steel or iron work in purlins and rafters including drilling holes and fixing in position and including supply of all steel, bolts and nuts, wastage, labour and T&P etc required for proper completion of work.

Excavation in foundation in ordinary soil, loame, clay or sand including lift upto 1.5 m and lead upto 30 m including filling watering and rammming of excavated earth in to the trenches or in to the space between the building & the side of foundation trenches or in to the plinth , removal & disposal of surplus earth as directed by the engineer in charge upto a distance of 30 m from the foundation trenches . ( Excluding royalty )

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. ON SEATING & TABLE

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm ON PLANTERS

Providing and laying factory made 80 mm thick interlocking Cement Concrete tiles (30 mpa) including 25 mm thick compacted bed of fine sand compacting and proper embedding /laying of interlocking tiles leveling and dressing of surface and including labour and T&P etc. but excluding of all material, labour T&P etc. required for proper completion of work as directer by engineer in chargr

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of pecified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20

Providing and laying factory made 80 mm thick interlocking Cement Concrete tiles (30 mpa) including 25 mm thick compacted bed of fine sand compacting and proper embedding /laying of interlocking tiles leveling and dressing of surface and including labour and T&P etc. but excluding of all material, labour T&P etc. required for proper completion of work as directer by engineer in chargr FOR ROAD

Fabrication and installation of MS powder coated ‘’U Shape’’ Dual Unit dustbins Internal Size- 325mm x 250mm x 500mm (H) Bin shall be made of 25x50mm section tube as an vertical support & 1.5mm thick MS sheet with laser cut perforation on vertical sides. Perforation on bottom base plate. Bin shall be powder coated of minimum grade of 60 micron. Provision for fixed with fastener on Pre-cast concrete block. vendor must have the own powder coating facility & submit the proof along with bid. (Note: Installation, J Bolt/ Fastner as per approved make & Civil/CC Footing work included approved makes:kich, ozone,

Providing and laying in Cement concrete 1:4:8 (1 Cement: 4 approved Coarse sand: 8 Coarse aggregate) size of aggregate shall be 4cm gauge or as approved including supply of all material labor, T&P etc. required for proper completion of the work. FOR FLOORING

Providing and fixing imported tensile fabric of make Ferrari or equivalent, over steel frames with all fittings and fixtures such as centenary cables PVC/SS membrane plates, swedge, fork etc. as per the direction of Engineer in Charge. Rate is inclusive of design providing and fixing fabric with all necessary accessories as required as per approved design complete. (Material Specification: -Tie Cables Galvanized Steel Core Make :- Usha Martin / Bharat Wire Rope, Material of End terminals and Nut bolts SS 304, End plates Mild Steel with Hot dip galvanized along with powder coating , Fabric Fixing Nuts and bolts HDG with 80 microns.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

1 Hp Pump SUBMERSIBLE PUMP SET

Supply and fixing of 20 mtr High mast Pole of approved make with rising system, hot dip Galvanized inside & outside , having pole sheet thickness 4mm,top dia minimum150mm, bottom dia minimum 410mm, base plate 32mm thick, suitable for wind velocity as per IS 875 part 3 &.having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes,1.5 HP Power tool motor, 3 point suspension system with steel wire rope 8 mm dia , double drum winch. Including making suitable Foundation as per manufacture drawing & site requirement along with foundation bolts, nuts, washers , anchor plates etc Complete in all respect as per direction and satisfaction to the Engineerin- charge.

Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 180 Watt. Confirming to IP 66 protection complete in all respect AA

Supply and wiring of 4 number 16 sq. mm. PVC insulated 1100 V grade single core aluminium conductor cable in 40 mm dia PVC conduit on surface, with two number 10sq mm single core aluminium conductor cable as earth continuity wire drawn in coudit. complete in all respect.

As in item no.261 but in 25 mm dia heavy duty (2 mm thick) PVC conduit with 2 nos 2.5 sq.mm.PVC insulated aluminium conductor cable as earth continuity wire drawn in conduit.

Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 meters below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick al round etc. as per directions of Engineer-in-charge complete in all respects as per drawing (This will apply for earthing of poles/high mast also).

The Job includes the grouting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubicle type switch board shall be of cat A & B Only

32 Amp. MCCB-3 Nos.

Cat. B. Panel Cubicle Type

Supply and fixing of Nature Switch for automatic control of light sensitive electrical circuit using space grade infra-red Sensor to adjust automatically On & Off adjustment. Time shall be adjusted as per seasonal variation of sunrise & sunset for single phase 5 k.watt load.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipe but without fittings and base support for tank.

Supply and fixing of 10 cm internal dia A.C. down pipe everest or charminar make complete with bends with door at top and plain at bottom and grating and including supply of necessary M.S. clamps 2.5cm x 3mm fixed to walls with and including supply of 15cm long 6mm dia nails all material labour and T&P etc Required for completion of the work and also including repair of plaster pointing etc. If damaged during fixing of the pipe.

As in item 730 above but with PVC Pipe (Kisan, supreme or equivalent) 6 kg/per sq.cm. Pressur 15 cm. dia.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455 x 610 mm and 45 cm deep for single pipe line

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supply and fixing of solar high mast light with all accessories 12.8V 50 Lithium Battery 120w Light

Wiring point for light in PVC conduit with 1.5 sq. mm. FRLSH PVC insulated multistrand copper conductor able as earthwire drawn inside the conduit,GP Box , piano type switch & ceiling rose/ angle/batten holder on 3 mm thick phenolic laminated backelite sheet etc., complete in all respect, as directed including matching colour wash

Supply and wiring of 4 number 16 sq. mm. PVC insulated 1100 V grade single core Copper conductor cable in 40 mm dia PVC conduit concealed in wall, with two number 10 sqmm single core Copper conductor cable as earth continuity wire drawn in coudit including matching colour wash etc., complete in all respect.

Supply and wiring of 3 number 4 sq. mm. PVCinsulated 1100V grade single core aluminium conducto cable in 25 mm dia heavy guage rigid steel conduit onsurface with two number 8 SWG GI earth continuity wire etc complete in all respect.

As in item no.231(B) but in 25 mm dia heavy duty (2mm thick) PVC conduit with 2 nos 2.5 sq.mm. FRLSHPVC insulated multistrand copper conductor cable asearth continuity wire drawn in conduit.

S & F surface/Flush mounting 12 ways SPN distribution board with additional metal door without MCB complete in all respect, as Direct by Engineer in Charge.

S&F of 63 Amp. D.P. Isolator

S&F of 40 Amp. SPMCB (10KA)C Curve

Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect

CAT- AAA

Supply and fixing of recess/ Surface/ Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect.

CAT- AA

PRAMOD KUMAR GUPTA

M/S RAJEEV TRADERS