Construction of Various New Infrastructure Development Works at RLBCAU, Jhansi Campus

Abstract of Cost - Civil/Plumbing/Electrical Works

S.No. Description DSR Amount NDSR Amount Total DSR + NDSR

Sub Total (DSR + NDSR) (excluding Fees) ₹ 149,923,196.00 A

Digitally signed by ARTI

CIVIL ESTIMATE SUMMARY

Sl. No. DESCRIPTION DSR Amount NDSR/ MR Amount

2.0 CONCRETE WORKS ₹ 58,89,484.95 ₹ 0.00

3.0 REINFORCED CEMENT CONCRETE WORKS ₹ 519,00,026.85 ₹ 0.00

6.0 MARBLE & GRANITE WORKS ₹ 60,859.40 ₹ 0.00

9.0 FLOORING WORKS ₹ 3,68,514.05 ₹ 0.00

10.0 ROOFING WORKS ₹ 4,473.75 ₹ 0.00

11.0 FINISHING WORKS ₹ 19,62,655.50 ₹ 0.00

13.0 ALUMINIUM & GLAZING WORK ₹ 4,24,833.25 ₹ 0.00

14.0 WATER PROOFING WORKS ₹ 22,70,652.90 ₹ 27,44,435.00

Modified Estimated Cost after using Correction

factor on DSR 2023 on account of GST @0.973

(Ref. CPWD Office Memorandum File No. ₹ 777,27,453.76 ₹ 0.00

158/SE (TAS)/GST/2024/O2-E dated 08-08-

15.0 HORTICULTURE WORKS ₹ 4,93,634.50 ₹ 0.00

GRAND TOTAL ₹ 809,83,032.29

GRAND TOTAL ₹ 809,83,032.29

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

1.1.2 Carriage of Earth

1.1.4 Carriage of Excavated Rock

Earth work in surface excavation not exceeding 30 cm in depth

but exceeding 1.5 m in width as well as 10 sqm on plan

2.1 including getting out and disposal of excavated earth upto 50 Sqm 2000.00 ₹ 129.85 ₹ 2,59,700.00

m and lift upto 1.5 m, as directed by Engineer-in- Charge

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m and

for all lift, as directed by Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m and

lift upto 1.5 m, as directed by Engineer-in-charge.

2.7.3 Hard rock (blasting prohibited) Cum 455.00 ₹ 1,432.95 ₹ 6,51,992.25

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means in foundation trenches or drains

(not exceeding 1.5 m in width or 10 sqm on plan), including

2.8 dressing of sides and ramming of bottoms, for all lift, including

getting out the excavated soil and disposal of surplus

excavated soil as directed, within a lead of 50 m.

Excavation work by mechanical means (Hydraulic excavator)/

manual means in foundation trenches or drains (not exceeding

1.5m in width or 10 sqm on plan), including dressing of sides

2.9 and ramming of bottoms, lift upto 1.5 m, including getting out

the excavated soil and disposal of surplus excavated soils as

directed, within a lead of 50 m.

2.9.3 Hard rock (blasting prohibited) Cum 425.00 ₹ 1,523.05 ₹ 6,47,296.25

Extra for every additional lift of 1.5 m or part thereof in

excavation / banking excavated or stacked materials.

2.26.1 All kinds of soil.

2.26.2 Ordinary or hard rock

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Close timbering over areas including strutting, shoring and

2.18 packing cavities (wherever required) etc. complete.

(Measurements to be taken of the face area timbered):

2.18.1 Depth not exceeding 1.5m Sqm 218.00 ₹ 125.80 ₹ 27,424.40

2.18.2 Depth exceeding 1.5m but not exceeding 3m Sqm 191.00 ₹ 144.10 ₹ 27,523.10

2.18.3 Depth exceeding 3m but not exceeding 4.5m Sqm 249.00 ₹ 163.15 ₹ 40,624.35

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm

2.25 in depth, consolidating each deposited layer by ramming and Cum 3770.00 ₹ 196.00 ₹ 7,38,920.00

watering, lead up to 50 and for all lift.

Supplying and filling in plinth with sand under floors

2.27 including, watering, ramming consolidating and dressing Cum 92.00 ₹ 2,123.75 ₹ 1,95,385.00

Surface dressing of the ground including removing vegetation

and inequalities not exceeding 15 cm deep and disposal of

rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil.

Anti termite treatment

Supplying chemical emulsion in sealed containers including

delivery as specified

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 62.00 ₹ 234.75 ₹ 14,554.50

Diluting and injecting chemical emulsion for POST-

2.35 CONSTRUCTIONAL anti-termite treatment (excluding the cost

of chemical emulsion) :

Along the external wall below concrete or masonry apron

using chemical emulsion @ 2.25 litres per linear metre

2.35.2.1 including drilling and plugging holes etc.: With Chlorpyriphos/ Metre 133.00 ₹ 53.45 ₹ 7,108.85

Lindane E.C. 20% with 1% concentration

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Treatment of soil under existing floors using chemical

emulsion @ one litre per hole, 300 mm apart including drilling

2.35.3 12 mm diameter holes and plugging with cement mortar 1 :2

(1 cement : 2 Coarse sand) to match the existing floor :

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Extra for levelling & neatly dressing of disposed soil

completely as directed by Engineer-in-charge.

TOTAL (Carried Over to Summary of Civil Works) ₹ 58,10,759.93 ₹ 0.00

Providing and laying in position cement concrete of specified

4.1 grade excluding the cost of centering and shuttering - All work

up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural

4.1.8 sources : 8 graded stone aggregate 40 mm nominal size Cum 841.00 ₹ 6,812.00 ₹ 57,28,892.00

derived from natural sources)

Centering and shuttering including strutting, propping etc.

and removal of form work for :

4.3.1 Foundations, footings, bases for columns Sqm 335.00 ₹ 392.15 ₹ 1,31,370.25

Making plinth protection 50mm thick of cement concrete 1:3:6

(1 cement : 3 coarse sand (zone-III) derived from natural

sources : 6 graded stone aggregate 20 mm nominal size

derived from natural sources) over 75mm thick bed of dry

brick ballast 40 mm nominal size, well rammed and

consolidated and grouted with fine sand, including necessary

excavation, levelling & dressing & finishing the top smooth.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

TOTAL (Carried Over to Summary of Civil Works) ₹ 58,89,484.95 ₹ 0.00

REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc.

and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses,

plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access

Lintels, beams, plinth beams, girders, bressumers and

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 827.00 ₹ 961.30 ₹ 7,94,995.10

5.9.7 Stairs, (excluding landings) except spiral staircases Sqm 10.00 ₹ 764.95 ₹ 7,649.50

5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sqm 11.00 ₹ 951.10 ₹ 10,462.10

Steel reinforcement for R.C.C. work including straightening,

5.22 cutting, bending, placing in position and binding all complete

upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening,

5.22A cutting, bending, placing in position and binding all complete

above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Add for plaster drip course/ groove in plastered surface or

moulding to R.C.C. projections.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended

proportions as per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and workability without

impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of

5.33 centering, shuttering, finishing and reinforcement as per

direction of the engineer-in-charge; for the following grades of

concrete. Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more

than 110% of the specified minimum cement content, the

contractor shall have discretion to either re-design the mix or

bear the cost of extra cement.

5.33.1 All works upto plinth level

Concrete of M25 grade with minimum cement content of 330

5.33.2 All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330

Add for using extra cement in the items of design mix over and

above the specified cement content therein.

TOTAL (Carried Over to Summary of Civil Works) ₹ 519,00,026.85 ₹ 0.00

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Brick work with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 12.00 ₹ 7,132.25 ₹ 85,587.00

Brick work with F.P.S. bricks of class designation 75 in

6.4 superstructure above plinth level up to floor V level in all

shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 100.00 ₹ 9,105.95 ₹ 9,10,595.00

Half brick masonry with F.P.S. bricks of class designation 75 in

superstructure above plinth level up to floor V level.

6.13.2 cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 58.00 ₹ 1,123.80 ₹ 65,180.40

TOTAL (Carried Over to Summary of Civil Works) ₹ 10,61,362.40 ₹ 0.00

Random rubble masonry with hard stone in superstructure

above plinth level and upto floor five level, including leveling

up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12

graded stone aggregate 20 mm nominal size) at window sills,

ceiling level and the like.

7.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 315.00 ₹ 9,275.45 ₹ 29,21,766.75

TOTAL (Carried Over to Summary of Civil Works) ₹ 29,21,766.75 ₹ 0.00

MARBLE & GRANITE WORK

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and fixing 18 mm thick gang saw cut, mirror

polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, facias and

similar locations of required size, approved shade, colour and

8.2 texture laid over 20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to give high

gloss finish etc. complete at all levels.

8.2.3 Granite stone slab colour black, Cherry/Ruby red

Providing edge moulding to 18 mm thick marble stone

counters, Vanities etc., including machine polishing to edge to

give high gloss finish etc. complete as per design approved by

Engineer-in-Charge. Granite work

Extra for providing opening of required size & shape for wash

basins/ kitchen sink in kitchen platform, vanity counters and

8.5 similar location in marble/Granite/Stone work including Each 3.00 ₹ 978.70 ₹ 2,936.10

necessary holes for pillar taps etc. including rubbing and

polishing of cut edge etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except

burgundy, bottle green, black of any size as approved by

Engineer-in-Charge, in skirting, risers of steps and dados, over

12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg per sqm,

including pointing in white cement mixed with pigment of

matching shade complete.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

TOTAL (Carried Over to Summary of Civil Works) ₹ 60,859.40 ₹ 0.00

WOOD & PVC WORK

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in

9.1 position with hold fast lugs or with dash fasteners of required

dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class Teak wood Cum 1.00 ₹ 1,42,949.70 ₹ 1,42,949.70

Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) non-decorative type, core of

block board construction with frame of 1st class hard wood

and well matched commercial 3 ply veneering with vertical

grains or cross bands and face veneers on both faces of

35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

Providing and fixing curtain rods of 1.25 mm thick chromium

plated brass plate, with two chromium plated brass brackets

fixed with C.P. brass screws and wooden plugs, etc., wherever

necessary complete :

Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc.

including priming coat with approved steel primer all

Fixed to openings /wooden frames with rawl plugs screws etc.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing 40x5 mm flat iron hold fast 400 mm long including

fixing to frame with 10 mm diameter bolts, nuts and wooden

9.53 plugs and embedding in cement concrete block each 33.00 ₹ 228.85 ₹ 7,552.05

300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6

graded stone aggregate 20mm nominal size).

Providing and fixing aluminium die cast body tubular type

universal hydraulic door closer (having brand logo with ISI, IS :

9.83 3564, embossed on the body, door weight upto 35 kg and door each 5.00 ₹ 1,124.85 ₹ 5,624.25

width upto 700 mm), with necessary accessories and screws

Providing and fixing SS sliding door bolts ISI marked of

MR-1 required colour or shade with nuts and screws etc. complete :

Providing and fixing SS tower bolts ISI marked of required

MR-2 colour or shade with necessary screws etc. complete :

Providing and fixing SS hanging type door stopper ISI marked

MR-3 of required colour and shade with necessary screws etc.

Single rubber stopper each 8.00 ₹ 109.65 ₹ 877.16

Providing & Fixing decorative high pressure laminated sheet

of plain / wood grain in gloss / matt / suede finish with high

9.127 density protective surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type S, including cost

of adhesive of approved quality.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and fixing fly proof stainless steel grade 304 wire

gauge, to windows and clerestory windows using wire gauge

with average width of aperture 1.4 mm in both directions with

wire of dia. 0.50 mm all complete.

9.135.2 With 12 mm mild steel U beading sqm 29.00 ₹ 1,228.00 ₹ 35,612.00

Providing and fixing bright /matt finished Stainless Steel

9.165 handles of approved quality & make with necessary screws etc

TOTAL (Carried Over to Summary of Civil Works) ₹ 4,08,639.50 ₹ 17,509.03

Supplying and fixing rolling shutters of approved make, made

of required size M.S. laths, interlocked together through their

entire length and jointed together at the end by end locks,

mounted on specially designed pipe shaft with brackets, side

guides and arrangements for inside and outside locking with

push and pull operation complete, including the cost of

providing and fixing necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of adequate

strength conforming to IS: 4454 - part 1 and M.S. top cover of

required thickness for rolling shutters. 80 x 1.25mm MS laths

with 1.25mm thick top cover.

80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 Providing and fixing ball bearing for rolling shutters. Each 7.00 ₹ 492.35 ₹ 3,446.45

Extra for providing mechanical device chain and crack

operation for operating rolling shutters.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Steel work welded in built up sections/ framed work including

cutting, hoisting, fixing in position and applying a priming coat

of approved steel primer using structural steel etc. as required

In gratings, frames, guard bar, ladder, railings, brackets, gates

and similar works.

Providing and fixing carbon steel galvanised ( minimum

coating 5 micron) dash fastener of 10 mm dia double threaded

6.8 grade (yield strength 480 N/mm2), counter sunk head,

comprising of 10 m dia polyamide PA 6 grade sleeve, including

drilling of hole in frame , concrete/ masonry, etc. as per

direction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made

of Hollow tubes, channels, plates etc., including welding,

grinding, buffing, polishing and making curvature (wherever

required) and fitting the same with necessary stainless steel

nuts and bolts complete, i/c fixing the railing with necessary

accessories & stainless steel dash fasteners , stainless steel

bolts etc., of required size, on the top of the floor or the side of

waist slab with suitable arrangement as per approval of

Engineer-in-charge, (for payment purpose only weight of

stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc.).

TOTAL (Carried Over to Summary of Civil Works) ₹ 4,06,602.45 ₹ 0.00

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Kota stone slab flooring over 20 mm (average) thick base laid

over and jointed with grey cement slurry mixed with pigment

11.26 to match the shade of the slab including rubbing and polishing

complete with base of cement mortar 1 : 4 (1 cement : 4 coarse

Kota stone slabs 20 mm thick in risers of steps, skirting, dado

and pillars laid on 12 mm (average) thick cement mortar 1:3 (1

cement 3 coarse sand) and jointed with grey cement slurry

mixed with pigment to match the shade of the slabs, including

rubbing and polishing complete.

Providing and laying Ceramic glazed floor tiles of size 300x300

mm (thickness to be specified by the manufacturer), of 1st

quality conforming to IS : 15622, of approved make, in all

colours, shades, except White, Ivory, Grey, Fume Red Brown,

11.38 laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Sqm 6.00 ₹ 1,315.30 ₹ 7,891.80

Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m

including pointing the joints with white cement and matching

pigments etc., complete.

Providing & Laying vitrified floor tiles in different sizes (

thickness to be specified by the manufacturer) with water

absorption's less than 0.08% and confirming to IS : 15622 of

11.41 approved make in all colours and shades, laid on 20mm thick

cement mortar 1:4 (1 cement : 4 coarse sand) including

grouting the joints with white cement and matching pigments

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and laying Vitrified tiles in different sizes (thickness

to be specified by manufacturer), with water absorption less

than 0.08 % and conforming to I.S. 15622, of approved make,

in all colours & shade, in skirting, riser of steps, over 12 mm

thick bed of cement mortar 1:3 (1 cement: 3 coarse sand),

jointing with grey cement slurry @ 3.3 kg/ sqm including

grouting the joint with white cement & matching pigments etc.

Providing and laying Polished Granite stone flooring in

required design and patterns, in linear as well as curvilinear

portions of the building all complete as per the architectural

drawings with 18 mm thick stone slab over 20 mm (average)

thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid

and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade

including rubbing, curing and polishing etc. all complete as

specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab of all colour and texture except

Black, Cherry/Ruby Red

TOTAL (Carried Over to Summary of Civil Works) ₹ 3,68,514.05 ₹ 0.00

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Making khurras 45x45 cm with average minimum thickness of

5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over P.V.C.

12.22 sheet 1 m x1 m x 400 micron, finished with 12 mm cement Each 15.00 ₹ 298.25 ₹ 4,473.75

plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the

outlet complete.

TOTAL (Carried Over to Summary of Civil Works) ₹ 4,473.75 ₹ 0.00

13.4 12 mm cement plaster of mix :

15 mm cement plaster on rough side of single or half brick wall

13.6 20 mm cement plaster of mix :

13.16 6 mm cement plaster of mix :

Pointing on stone work with cement mortar 1:3 (1 cement : 3

fine sand) : Raised and cut pointing

White washing with lime to give an even shade: New work

(three or more coats)

Painting Steel work with Deluxe Multi Surface Paint to give an

even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over

13.48.3 an under coat of primer applied @ 0.80 ltr/ 10 sqm of Sqm 14.00 ₹ 170.70 ₹ 2,389.80

approved brand and manufacture including preparation of

surfaces complete in all respect.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Applying priming coats with primer of approved brand and

13.85 manufacture, having low VOC (Volatile Organic Compound )

With ready mixed pink or grey primer on wood work (hard

soft wood) having VOC content less than 50 grams/ litre

With water thinnable cement primer on wall surface having

13.85.3 VOC content less than 50 grams/litre Sqm 385.00 ₹ 73.95 ₹ 28,470.75

Wall painting with acrylic emulsion paint, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre, of

13.82 approved brand and manufacture, including applying

additional coats wherever required, to achieve even shade and

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm)

13.45.1 over and including priming coat of exterior primer applied @ Sqm 278.00 ₹ 223.60 ₹ 62,160.80

Painting with synthetic enamel paint of approved brand and

13.62 manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable

13.62.1 shade with ordinary paint of approved brand and manufacture Sqm 22.00 ₹ 226.25 ₹ 4,977.50

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the

plastered wall surface to prepare the surface even and smooth

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

TOTAL (Carried Over to Summary of Civil Works) ₹ 19,62,655.50 ₹ 0.00

Supplying at site Angle iron post & strut of required size

including bottom to be split and bent at right angle in opposite

direction for 10 cm length and drilling holes upto 10 mm dia.

Providing and fixing concertina coil fencing with punched tape

concertina coil 600 mm dia 10 metre openable length ( total

length 90 m), having 50 nos rounds per 6 metre length, upto 3

m height of wall with existing angle iron ‘Y’ shaped placed

2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced

barbed wire, stud tied with G.I. staples and G.I. clips to retain

16.53 horizontal, including necessary bolts or G.I. barbed wire tied to Meter 1025.00 ₹ 375.80 ₹ 3,85,195.00

angle iron, all complete as per direction of Engineer-in-charge,

with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm

thick) wire of high tensile strength of 165 kg/ sq. mm with

tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of

M.S. angle, C.C. blocks shall be paid separately)

Providing and laying 60 mm thick faciory made cement

concrete interlocking paver block of M -30 grade made by

block making machine with strong vibratory compaction, of

16.68 approved size, design & shape, laid in required colour and Sqm 3000.00 ₹ 972.00 ₹ 29,16,000.00

pattern over and including 50 mm thick compacted bed of

coarse sand, filling the joints with line sand etc. all complete as

per the direction of Engineer-in-charge.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and laying at or near ground level factory made kerb

stone of M-25 grade cement concrete in position to the

required line, level and curvature, jointed with cement mortar

1:3 (1 cement: 3 coarse sand), including making joints with or

without grooves (thickness of joints except at sharp curve shall

16.69 not to more than 5 mm), including making drainage opening Cum 15.00 ₹ 10,117.60 ₹ 1,51,764.00

wherever required complete etc. as per direction of Engineer-

in-charge (length of finished kerb edging shall be measured to

calculate volume for payment). (Precast C.C. kerb stone shall be

approved by Engineer-in-charge).

Providing and fixing factory made precast RCC perforated

drain covers, having concrete of strength not less than M-25, of

size 1000 x 450x50 mm, reinforced with 8 mm dia four nos

longitudinal & 9 nos cross sectional T.M.T. hoop bars, including

providing 50 mm dia perforations @ 100 to 125 mm c/c,

including providing edge binding with M.S. flats of size 50 mm

x 1.6 mm complete, all as per direction of Engineer-in-charge.

TOTAL (Carried Over to Summary of Civil Works) ₹ 63,93,699.00

ALUMINIUM & GLAZING WORK

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and fixing aluminium work for doors, windows,

ventilators and partitions with extruded built up standard

tubular sections/appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS : 1285, fixed with

rawl plugs and screws or with fixing clips, or with expansion

hold fasteners including necessary filling up of gaps at

junctions, at top, bottom and sides with required

21.1 PVC/neoprene felt etc. Aluminium sections shall be smooth,

rust free, straight, mitred and jointed echanically wherever

required including cleat angle, Aluminium snap beading for

glazing / paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the directions of

Engineer-in-charge. Glazing and paneling to be paid for

21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder

coating 50 micron)

For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making provision for

21.1.2 fixing of fittings wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings shall be paid for

Powder coated aluminium (minimum thickness of powder

coating 50 micron)

Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber /

21.3 neoprene gasket etc. complete as per the architectural

drawings and the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item):

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

With float glass panes of 5 mm thickness (weight not less than

Filling the gap in between aluminium frame and adjacent

RCC/Brickwork/ Stone Work by providing weather silicon

sealant over backer rod of approved quality as per

architectural drawings and direction of Engineer-in-charge

21.8.1 Upto 5mm depth and 5mm width metre 52.00 ₹ 96.75 ₹ 5,031.00

TOTAL (Carried Over to Summary of Civil Works) ₹ 4,24,833.25 ₹ 0.00

Providing and laying integral cement based treatment for

waterproofing on horizontal surface at all depth below ground

level for under ground structures as directed by Engineer-in-

charge and consisting of:

i) Ist layer of 22 mm to 25 mm thick approved and specified

rough stone slab over a 25mm thick base of cement mortar 1:3

(1 cement : 3 coarse sand) including applying twice (at base

and top of mortar) cement slurry @ 2.2kg/sqm (each time)

mixed with water proofing compound conforming to IS:2645

in the recommended proportion over the levelling course

(levelling course to be paid seperately). Joints sealed and

grouted with cement slurry mixed with water proofing

ii) 2nd layer of 25mm thick cement mortar 1:3 (1 cement : 3

coarse sand) mixed with water proofing compound in

recommended proportions.

iii) Finishing top with stone aggregate of 10mm to 12mm

nominal size spreading @ 8 cudm/sqm thoroughly embedded

in the 2nd layer.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Using rough Kota stone Sqm 597.00 ₹ 1,515.60 ₹ 9,04,813.20

Providing and laying integral cement based treatment for

water proofing on the vertical surface by fixing specified stone

slab 22mm to 25 mm thick with cement slurry mixed with

water proofing compound conforming to IS:2645 in

recommended proportions with a gap of 20mm (minimum)

between stone slabs and the receiving surfaces and filling the

gaps with neat cement slurry mixed with water proofing

compound and finishing the exterior of stone slab with cement

mortor 1:3 (1 cement:3 coarse sand) 20mm thick with neat

cement punning mixed with water proofing compound in

recommended proportion complete at all levels and as

directed by Engineer-in-charge.

Using rough Kota stone Sqm 200.00 ₹ 2,024.70 ₹ 4,04,940.00

Providing and placing in position suitable PVC water stops

confirming to IS: 12200 for construction/ expansion joints

22.4.1 between two RCC members and fixed to the reinforcement Rmt. 254.00 ₹ 327.65 ₹ 83,223.10

with binding wire before pouring concrete etc. complete:

Serrated with central bulb (225mm wide, 8-11mm thick).

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and laying integral cement based water proofing

treatment including preparation of surface as required for

treatment of roofs, balconies, terraces etc consisting of

following operations: (a) Applying a slurry coat of neat cement

using 2.75 kg/sqm of cement admixed with water proofing

compound conforming to IS. 2645 and approved by Engineer-

in-charge over the RCC slab including adjoining walls upto 300

mm height including cleaning the surface before treatment. (b)

Laying brick bats with mortar using broken bricks/brick bats

22.7 25 mm to 115 mm size with 50% of cement mortar 1:5 (1

cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-

in-charge over 20 mm thick layer of cement mortar of mix 1:5

(1 cement :5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-

in-charge to required slope and treating similarly the adjoining

walls upto 300 mm height including rounding of junctions of

walls and slabs.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

(c) After two days of proper curing applying a second coat of

cement slurry using 2.75 kg/ sqm of cement admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineerin- charge. (d) Finishing the surface with

20 mm thick jointless cement mortar of mix 1:4 (1 cement :4

coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineerin- charge

including laying glass fibre cloth of approved quality in top

layer of plaster and finally finishing the surface with trowel

with neat cement slurry and making pattern of 300x300 mm

square 3 mm deep. (e) The whole terrace so finished shall be

flooded with water for a minimum period of two weeks for

curing and for final test. All above operations to be done in

order and as directed and specified by the Engineer-in-Charge

With average thickness of 120 mm and minimum thickness at

khurra as 65 mm.

Surface Preparation, Crack/Joint Treatment & 2-

Component Acrylic Cementitious Waterproofing

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Providing and applying integral waterproofing treatment to

horizontal and vertical RCC surfaces, including thorough

surface preparation by mechanical wire brushing/grinding to

remove laitance, loose particles, oil, grease and all deleterious

materials, cleaning the surface with compressed air/water jet,

repairing honeycombs, surface defects and voids using

polymer modified non-shrink repair mortar, treatment of all

visible cracks by routing and filling with epoxy/polymer

modified repair system as per manufacturer's

recommendations, pressure grouting of construction/cold

joints through pre-fixed PVC nozzles with non-shrink

cementitious grout admixed with suitable expansive

plasticizing grout additive wherever required, sealing of pipe

penetrations and core cuts using epoxy bonding agent

followed by non-shrink grout and reinforcing with waterproof

joint tape embedded in polymer modified waterproof coating,

forming 75 mm × 75 mm coving at all wall-floor and wall-wall

junctions with cement mortar (1:4) admixed with Styrene

Butadiene Rubber (SBR) latex at manufacturer's

recommended dosage, complete with curing and preparation

of the surface to receive the waterproofing system.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

The prepared surface shall thereafter be treated with two

coats of two-component acrylic polymer modified

cementitious waterproof coating reinforced with alkali-

resistant fibre mesh embedded between the coats, applied

uniformly at a minimum total consumption of 2.0 kg/sqm to

achieve a minimum dry film thickness (DFT) of 1.0 mm. The

coating shall possess minimum elongation of 120%, crack-

bridging ability up to 2 mm, tensile strength not less than 0.9

N/mm² and adhesion strength not less than 0.8 N/mm². The

work shall include all materials, labour, scaffolding, tools &

plants, curing, testing, wastage, complete surface preparation

and all incidental works required to complete the

waterproofing treatment in accordance with the

manufacturer's specifications and as directed by the Engineer-

Providing & applying two coats of 2-component acrylic

MR-5 cementitious coating followed by food-grade epoxy coating Sqm 365.00 ₹ 979.00 ₹ 3,57,335.00

(UGT) on the inner side of the tank.

Providing & applying two coats of 2-component acrylic

MR-6 cementitious coating followed by coal tar epoxy coating (STP) Sqm 680.00 ₹ 951.00 ₹ 6,46,680.00

on the inner side of the tank.

TOTAL (Carried Over to Summary of Civil Works) ₹ 22,70,652.90 ₹ 27,44,435.00

Horticulture Work:

2.2/ DSR Supplying and stacking of good earth at site including royalty

2025 and carriage upto 5 km lead complete (earth measured in Cum. 240.00 ₹ 803.75 ₹ 1,92,900.00

(H&L) stacks will be reduced by 20% for payment).

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Supplying and stacking at site dump manure from approved

source, including carriage upto 5 km lead complete (manure

measured in stacks will be reduced by 8% for payment):

Screened through sieve of I.S. designation 4.75 mm.

Mixing earth and sludge or manure in the required proportion

specified or directed by the Officer-in-charge

Spreading of sludge, dump manure and/or good earth in

required thickness as per direction of officer-in-charge (cost of

sludge, dump manure and/ or good earth to be paid

Grassing with selection No. 1 Doob grass including watering

2.10.2/ and maintenance of the lawn for 30 days or more till the grass

DSR 2025 forms a thick lawn, free from weeds and fit for mowing Sqm 1000.00 ₹ 20.30 ₹ 20,300.00

(H&L) including supplying good earth, if needed (the grass and good

earth shall be paid for separately) - With Turf Grass.

2.6/ DSR Uprooting weeds from the trenched area after 10 to 15 days of

2025 its flooding with water including disposal of uprooted Sqm 1000.00 ₹ 7.45 ₹ 7,450.00

(H&L) vegetation.

Providing & laying of Selection no. 1 Doob grass turf with earth

50mm to 60mm thickness of existing ground prepared with

2.34/ DSR proper level and ramming with required tools wooden and

2025 than rolling the surface with light roller make the surface Sqm. 1000.00 ₹ 113.70 ₹ 1,13,700.00

(H&L) smoothen and light watering the same and maintenance for 30

days or more till the grass establish properly, as per direction

of the officer-in-charge.

DSR Amount NDSR Amount

DSR-2023 DESCRIPTION UNIT Quantity Rate (INR)

Digging holes in ordinary soil and refilling the same with the

excavated earth mixed with manure or sludge in the ratio of

2:1 by volume (2 parts of stacked volume of earth after

reduction by 20% : 1 part of stacked volume of manure after

reduction by 8%) flooding with water, dressing including

removal of rubbish and surplus earth, if any, with all leads and

lifts (cost of manure, sludge or extra good earth if needed to be

paid for separately): Holes 90 cm dia, and 90 cm deep

TOTAL (Carried Over to Summary of Civil Works) 0.00 ₹ 4,93,634.50 ₹ 0.00

Project Name:- “Construction of various New Infrastructure Development

Works at RLBCAU, Jhansi Campus”.

S.NO NAME OF SUB-HEAD

DSR 2025 items Non Scheduled items

1 EXTERNAL ELECTRICAL WORKS ₹ 30,849,610.20 ₹ 18,147,864.39

2 INTERNAL ELECTRICAL WORKS ₹ 579,313.00 ₹ 75,399.06

Digitally signed by A

Project Name:- “Construction of various New Infrastructure Development Works at

RLBCAU, Jhansi Campus”.

S.NO NAME OF SUB-HEAD

DSR 2025 items Non Scheduled items

1 SUB HEAD-I : EXTERNAL LIGHTING WORK ₹ 1,087,682.00 ₹ 1,142,772.19

2 SUB HEAD-II : SOLAR SYSTEM WORK ₹ 16,284,000.00 ₹ 0.00

3 SUB HEAD -III SUBSTATION WORK ₹ 13,267,510.00 ₹ 16,939,062.80

4 Sub Head: IV SUB STATION LIGHT WIRING ETC ₹ 210,418.20 ₹ 66,029.40

Digitally signed by A

Project Name:- “Construction of various New Infrastructure Development Works at RLBCAU, Jhansi Campus”.

Electrical Work (As per DSR:- 2025)

Sr.No. Name of Sub Head

DSR 2025 Item Non Schedule Items

A) Sub Head: Distribution Board ₹ 49,460.00

B) Sub Head: Internal Wiring ₹ 419,330.00

C) Sub Head: Cable Tray and Raceway ₹ 25,000.00

D) Sub Head: Earthing ₹ 35,782.00

E) Sub Head: Cable & Terminations ₹ 8,102.00 ₹ 70,999.50

F) Sub Head: Light Fixture and Fan ₹ 41,639.00 ₹ 4,399.56

Digitally signed by A

Project Name:- “Construction of various New Infrastructure Development Works at RLBCAU, Jhansi Campus”.

ELECTRICAL WORKS As per DSR 2025 As per Market Rate

DSR-2025 Total

Description Unit Rate(Rs) Amount Rate(Rs) Amount

A) Sub Head: Distribution Board

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess

complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

DSR:2025- 12 way, Double door

Supplying and fixing following way, horizontal type three

pole and neutral, sheet steel, MCB distribution board, 415 V,

on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But without

MCB/RCCB/ Isolator)

DSR:2025- 8 way (4+24) Double door

Digitally signed by A

Supplying and fixing following ways,surafce/recess

mounting,vertical type,415V,TPN MCB distribuiton board of

sheet steel,dust protected,duly powder painted,inclusive of

200A tinned copper busbar,common neutral link,earth bar,din

bar of mounting MCBs (but without MCBs and incomer) as

required. (Note: Vertical type MCB TPDB is normally used

where 3 Phase outlets are required)

DSR:2025- 8 way (4+24) Double door

Supplying and fixing following rating, double pole, 240 volts,

isolator in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts,

isolator in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing 5A to 32A rating, 240/415 volts, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

DSR:2025- Supplying and fixing single pole blanking plate in the existing

2.11 MCB DB complete etc. as required.

Digitally signed by A

Supplying and fixing following rating, double pole, (single

phase and neutral), 240 volts, residual current circuit breaker (

DSR:2025-2.14 RCCB), having a sensitivity current 30mA in the existing

MCB DB complete with connections, testing and

commissioning etc as required.

Providing and fixing following rating and breaking capacity

and pole MCCB with thermomagnetic release and terminal

DSR:2025-2.2 spreaders in existing cubical panel board including drilling

holes in cubical panel,making connections,etc.as required.

Supply and fixing DP sheet Steel enclosure on surface/recess

DSR:2025- along with 25/32A 240V ''C'' curve DP MCB complete with

2.16 connections,testing and commissioning etc.as required.

Total of Sub Head Distribution Board ₹ 49,460.00 ₹ 0.00

B) Sub Head: Internal Wiring

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed steel conduit, with

DSR:2025-1.3 modular switch, modular plate, suitable GI box and earthing

the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

DSR:2025- Group - C

Digitally signed by A

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without independent

switch etc.) with1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed steel conduit,

and earthing the pointwith 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc. as required.

DSR:2025- Group - C

Wiring for twin control light point with 1.5 sq.nn. FRLS PVC

insulated copper conductor single core cable in

surface/recessed steel conduit, 2 way modular switch,modular

plate,suitable GI Box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated coper conductor single core cable etc.as

Wiring for circuit/ submain wiring alongwith earth wire with

the following sizes of FRLS PVC insulated copper conductor,

single core cable in surface/ recessed Steel conduit as required

DSR:2025- 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

DSR:2025- 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

DSR:2025- 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

DSR:2025- 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

DSR:2025- 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

DSR:2025- 4 x 10 sq.mm + 2 x 6 sq.mm. earth wire

Digitally signed by A

Supplying and fixing suitable size GI box with modular plate

and cover in front on surface or in recess, including providing

and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps Each 15 ₹ 545.00 ₹ 8,175.00 ₹ 0.00

modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate

and cover in front on surface or in recess, including providing

and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and Each 10 ₹ 659.00 ₹ 6,590.00 ₹ 0.00

15/16 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate

and cover in front on surface or in recess, including providing

DSR:2025- and fixing 2 nos. 3 pin 5/6A moduler socket outlet and 2nos.

1.56 5/6A modular switch, connection etc. as required. (For light

plug to be used in non residential buildings).

Supplying and fixing following modular switch/socket on the

existing modular plate & switch box including connections

but excluding modular plate etc.as required.

DSR:2025- 5/6A switch

DSR:2025- 3 pin 5/6 A socket outlet

DSR:2025- 15/16A switch

DSR:2025-1.24.7TV antenna socket outlet Each 1 ₹ 168.00 ₹ 168.00 ₹ 0.00

Supplying and fixing following Modular base & cover plate

on existing modular metal boxes etc. as required. (For Table)

Digitally signed by A

DSR:2025- Supplying and fixing of call bell / buzzer suitable for single

1.38 phase,230 volt complete as required.

Total of Sub Head Internal Wiring ₹ 419,330.00 ₹ 0.00

C) Sub Head: Cable Tray and Raceway

Perforated Cable Tray

Supplying and installing following size of perforated painted

with powder coating M.S cable trays with perforation not

more than 17.5%, inconvenient sections, joined with

connectors, suspended from the ceiling with M.S. suspenders

including bolts&nuts, painting suspenders etc as required.

DSR:2025- 150 mm width X 50 mm depth X 1.6mm thickness

Supplying and installing following size of perforated painted

with powder coating M.S cable trays bends with perforation

not more than 17.5%, inconvenient sections, joined with

connectors, suspended from the ceiling with M.S. suspenders

including bolts & nuts, painting suspenders etc as required.

DSR:2025- 150 mm width X 50 mm depth X 1.6mm thickness

Digitally signed by A

Supplying and installing following size of perforated painted

with powder coating M.S cable trays Tee with perforation not

more than 17.5%, joined with connectors, suspended from the

ceiling with M.S. suspenders including bolts&nuts, painting

suspenders etc as required.

DSR:2025- 150 mm width X 50 mm depth X 1.6mm thickness

Total of Sub Head Cable Tray and Raceway ₹ 25,000.00 ₹ 0.00

D) Sub Head: Earthing

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm

thick including accessories, and providing masonry enclosure

with cover plate having locking arrangement and watering Set 2 ₹ 8,351.00 ₹ 16,702.00 ₹ 0.00

pipe of 2.7 metre long etc. with charcoal/ coke and salt as

Supplying and laying 6 SWG G.I. wire at 0.50 metre below

ground level for conductor earth electrode, including

connection/ termination with GI thimble etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia

DSR:2025- G.I. pipe from earth electrode including connection with G.I.

5.11 nut, bolt, spring, washer excavation and re-filling etc. as

DSR:2025- Providing and fixing 6 SWG dia G.I. wire on surface or in

5.16 recess for loop earthing as required.

Total of Sub Head Earthing ₹ 35,782.00 ₹ 0.00

E) Sub Head: Cable & Terminations

Digitally signed by A

Laying of one number PVC insulated and PVC sheathed /

DSR:2025- XLPE power cable of 1.1 KV grade of following size in the

10.5 existing RCC/ HUME/ METAL pipe as required.

DSR:2025- Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed /

XLPE power cable of 1.1 KV grade of following size in the

existing masonry open duct as required.

DSR:2025- Upto 35 sq. mm

Laying and fixing of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of following

size on cable tray as required.

DSR:2025- Upto 35 sq. mm (clamped with 1mm thick saddle)

Supplying and making end termination with brass

compression gland and aluminium lugs for following size of

PVC insulated and PVC sheathed / XLPE aluminium

Supply of MV cable

Supply, following sizes of PVC sheathed PVC/XLPE

NS: 5 insulated Aluminium conductor power/ multicore control

armoured cable of 1.1 KV grade.

NS: 5.1 3 ½ C - 35 sq mm Aluminium Meter 125 ₹ 512.18 ₹ 64,022.75

NS: 5.2 4C- 10 sq mm Aluminium Meter 20 ₹ 348.84 ₹ 6,976.75

Total of Sub Head Cable & Terminations ₹ 8,102.00 ₹ 70,999.50

F) Sub Head: Light Fixture and Fan

Digitally signed by A

Supplying, installation, testing and commissioning of

following LED fitting (luminaries) panel light in round/

square shape complete with electronic driver heat sink

capacitor and all other accessories on surface/ in false

ceiling etc. as per specification and P.F. should be greater than

0.9. LED chip efficacy ratio * 120 lumens /watt.

Supplying, installation, testing and commissioning of

following sleek LED panel down lighters (luminaries) in

round/ square shape complete with electronic driver heat

sink capacitor and all other accessories on surface/ in false

ceiling etc. as per specification and P.F. should be greater

than 0.9. LED chip efficacy ratio * 120 lumens /watt.

Supplying, installation, testing and commissioning of

following LED tube light fitting including batten with

Electronic Driver Heat sink Capacitor complete with all

8.10. other accessories on surface/ in false ceiling, including

connection, earthing etc complete as per specification and

IP20, P.F. should be greater than 0.9. LED chip efficacy

ratio * 120 lumens /watt.

SITC Fresh air exhaust fan with louvers 300 mm sweep,

240V, single phase

Digitally signed by A

Supply, Installation, Testing and Commissioning of 1200mm

sweep BEE 5 Star rated, ceiling fan with Brush Less Direct

Current (BLDC) Motor, class of insulation: B, 3nos. Blades,

30 cm long down rod, 2 nos. canopies, shackle kit, safety

rope, copper winding, power factor not less than 0.9, service

valve (CM/M/W) minimum 6.00, Air delivery minimum210

Cum/Min, 350 RPM (tolerance as per IS:374-2019), THD less

than 10%, remote or electronic regulator unit for speed

control and all remaining accessories including safety pin, nut

bolts, washers, temprature rise=75 degree C (max.), insulation

resistance more than 2 mega ohm, suitable for 230V, 50 Hz,

single phase AC Supply, earthing etc. complete as required.

Total of Sub Head Light Fixture and Fan ₹ 41,639.00 ₹ 4,399.56

Digitally signed by A

Project Name:- “Construction of various New Infrastructure Development Works at RLBCAU, Jhansi Campus”.

DSR -2025 AS PER DSR25 AS PER MARKET RATE

DESCRIPTION OF ITEM UNIT QTY.

ITEMS RATE (RS.) AMOUNT (RS.) RATE (RS.) AMOUNT (RS.)

SUB HEAD-I : EXTERNAL LIGHTING WORK

Supply of following sizes XLPE insulated (Heavy duty) Aluminium conductor armoured cables

suitable for working voltage upto and including 1100 Volts complete as required and as per

specifications.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of

following size in the existing RCC/ HUME/ METAL pipe as required.

DSR-2025- Upto 35 sq. mm

Supply, laying and termination of the following sizes of 650/1100 volts grade PVC insulated

copper conductor wires in existing conduits including end terminations with copper lugs.

DSR-2025- 2 X 6 sq. mm PVC insulated copper conductor wire along with 1 X 2.5sq.mm PVC insulated RM

1.14.4 copper conductor wire

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete

with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

DSR-2025- 100mm dia

DSR-2025- 250mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories

like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting,

jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the

trench but excluding sand cushioning and protective covering etc., complete as required.

NS-1.2 Supply, erection, testing and commissioning of 6 M high Tubular pole as per Technical

specifications and with following components :-

Including supply and installation of 6 ways-20A connector & 6A MCB mounted on 6mm thick

painted M.S/GI plate, insulated, and fixed inside the pole suitable for termination of armoured

aluminium cable as required. Wiring to Luminaries from the 6A MCB, with 3x2.5 sq.mm. PVC

insulated copper, stranded conductor (P+N+PE) double sheathed wire including terminations.

6 meters high tubular pole with Double arm of length 1.5 meter, smoothly curved making an Nos.

angle of 10 deg to 15 deg with the horizontal plane complete as required.

Digitally signed by A

Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated

pressure die cast aluminium body with driver as per the requirement with Driver efficiency

>85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50

0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD

< 10% as per IEC 61000-3-2, P. F.?0.95, IP-66,IK-10, CRI >70, under voltage and over voltage

protection, EMI- EMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per

the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life

time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial

DSR-2025- Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K

8.13 / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour

Matching) <5, Maximum power consumption should not more than the specified rating and

Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5

sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy ?120 <135 lm/Watt

output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be

submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction temperature shall

not rise above 90°C).

Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die

cast aluminium body with built in or separate driver as per the requirement with Driver

efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating

temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5,

Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.?0.95, IP-66,IK-10, CRI >70,

under voltage and over voltage protection, EMI-EMC as per CISPR -15, lenses for beam angle 30

deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time

(LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial

DSR-2025- Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K

8.15 / 4000°K / 5700°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color

Matching) <5, Maximum power consumption should not more than the specified rating and

Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5

sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy ?105 <120 lm/Watt

output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be

submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction temperature shall

not rise above 90°C).

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and

providing masonry enclosure with cover plate having locking arrangement and watering pipe of Set 8 ₹ 8,351.00 ₹ 66,808.00

2.7 metre long etc. with charcoal/ coke and salt as required.

Supply and fixing in position the following G.I. tape/wires including providing all fixing

accessories and effecting proper connections.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode

including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. Metre 150 ₹ 755.00 ₹ 113,250.00

Digitally signed by A

DSR-2025- Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth RM

5.7 electrode, including connection/ termination with GI thimble etc. as required.

Total of Sub-Head -I carried to summary sheet Rs ₹ 1,087,682.00 ₹ 1,142,772.19

SUB HEAD-II : SOLAR SYSTEM WORK

Supply, Installation, Testing and Commissioning of on grid Solar Photovoltaic Power Plant

conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon

solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI

structure of suitable strength with following components complete as required:-

a) Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to

IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module

conversion efficiency shall not be less than 16.5%. PV modules used in solar power

plants/systems must be warranted for their output peak watt capacity, which should not be less

than 90% at the end of 10 years and 80% at the end of 25 years.

DSR-2025- b) Power Conditioning Unit (PCU) of 350-800V DC Input voltage range and 400V AC, three

17.1 phase, 4 wire, 50Hz +/-2.5Hz, output voltage suitable to generate AC Power with efficiency not

less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from

0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage

c) Data Monitoring System complete with accessories.

d) Fixing of Array junction box & Main junction box with IP65 protection and termination

arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc.

e) Lightning and surge voltage protection.

[Note: Solar PV system to be executed at rooftop of 9 different Buildings inside campus]

Total of Sub-Head -Vcarried to summary sheet Rs ₹ 16,284,000.00 ₹ 0.00

SUB HEAD -III SUBSTATION WORK

NS-3.1 RMU (11kV)

1 input and 4 outgoings

Supply, installation, testing and commissioning of 11 kV, 5-way SF6 gas insulated Ring Main

comprising two numbers SF6 Load Break Switches (LBS) and three number SF6 Circuit Breaker

complete with numerical protection relay, metering, earthing switches, interlocks and all

accessories, suitable for

11 kV, 50 Hz distribution system, as per CPWD / IEC standards, complete in all respects.

1. System Parameters

• Rated Voltage: 12 kV

• Nominal System Voltage: 11 kV

• Frequency: 50 Hz

Digitally signed by A

• System Earthing: Solid / Resistance earthed

• Short Circuit Rating: LBS – 21 kA (making), Circuit Breaker – 21 / 25 kA for 3 sec

• Insulation Level: Power frequency withstand 28 kV (rms), Lightning impulse withstand 75 kVp

2. RMU Configuration

• Incomer: 1 No. SF6 Load Break Switch – 630 A

• Outgoing-1: 1 No. SF6 Load Break Switch – 630 A

• Outgoing-2: 3 No. SF6 Circuit Breaker – 630 A

• Total: 5-way SF6 RMU (2 LBS + 3 CB)

3. SF6 Load Break Switch

• SF6 gas insulated Load Break Switch, rated current 630 A

• Short circuit making capacity 21 kA

• Sealed-for-life gas system

• Manual operation with quick make-quick break mechanism

• Mechanical endurance minimum 5,000 operations

• Integrated earthing switch with mechanical interlocking

4. SF6 Circuit Breaker Feeder

• SF6 Circuit Breaker rated at 630 A

• Breaking capacity 21 / 25 kA

• Spring charged operating mechanism, manual / motorized

• Trip-free mechanism

• Mechanical endurance minimum 10,000 operations

• CPWD General Specifications for Electrical Works

OEM Factory fitted

NS-3.2 HT Panel Main (1 incoming 2 outgoings)

Design, manufacture, supply, delivery including supervision during installation, testing and

commssioning of 1

panel, 11KV HT VCB switch board with following accessories: type tested Indoor Air insulated

2500A, 26.3kA / 40kA (3sec), 3 Phase, metal clad, horizontal draw out type Switchboard with

breaker. Panel will be manufactured by OEM only

a. One No. incoming panel equipped with following:-

630A, 11KV, VCB 25 KA, TP, totally enclosed, air insulated metal clad housing, cassette

mounted horizontal

isolation, horizontal drawout type, motorised spring charged, manually operated, trip free,

vaccum circuit breaker

(VCB) having double isolation features and control devices complete with mechanical with

continous tripping &

closing, coil suitable for 24V DC, shunt trip coil, OFF/ON indicators, mechanical operation

counter & provided

with following: Spring charge / discharge mechanical OFF push buttons for emergency trip (test /

service position limit switches

Digitally signed by A

with 6 NO/6 NC breaker auxiliary contacts in service position and The cubicle shall be of LSC

2B (Loss of Service

Continuity) and PM (Partition Class) classes as defined by IEC standard 62271-200. And it shall

high voltage compartments and one LV cabinet

CT chamber with single wound single phase, dual core cast resin CT, 15VA burden with core-1

for metering (CL-

1) and core-2 for protection (CL-5P10) and of 110/5+5A ratio.

Wireless communication energy sensor that monitors and measures energy and power in real-

time is required so

that can count on operational efficiency and uptime.

Microprocessor based relay, IDMT, Time delay with 3 elements for over current (50-200%) and

earth fault protection(10-40%) .-1 Set

Antipumping relay & master trip relay- 1 Set

Digital Ammeter with selector switch.-1 Set

A set of breaker ON/OFF/Trip/DC control supply/ Spring Charged indication lamp. 1 Set

Emergency trip push button on front door 1 Set

Limit switches with 6 NO/ 6 NC breaker auxiliary contacts 1 Set

Control:- T-N-C (Trip, Neutral, Close) breaker control switch. 1 Set

Space heater with thermostat for moisture absorption. 1 Set

Suitable for connection to 2 Runs x 3 core x 300 sq.mm. Cross linked polythelene (XLPE) 33KV

called for. 1 Set

HT Danger Plate 1 Set

Hooter low intensity 24 Volt with acknowledge and reset push button 1 Set

6-window microprocessor based annunciation panel with audio and visual indicator.

Over current & earth fault - 2 windows

Master trip operated - 1 window

Spare - 3 windows

Surge Arrestor, 10KA, Class II 1 Set

Thermal monitoring shall be fitted on HV field cable/busbar connections monitoring shall be

done by a battery less sensor that communicates wirelessly using Zigbee Green Power protocol.

The Incoming as described above.

800A, 11KV, 25 KA, 3 phase, air insulated Electrolytic grade copper bus bars

c.Feeder panel for, equipped with following :-

2 nos. 630A, VCB 11KV 25 KA, TP, Totally enclosed, air insulated, metal clad housing, cassette

horizontal isolation, horizontal drawout type, motorised spring charged, manually operated, trip

free,each vaccum

circuit breaker having double isolation features and control devices complete with mechanical

tripping & closing, coil suitable for 24V DC, shunt trip coil OFF/ON indicators mechanical

operation counter &

provided with each feeder following:

Spring charge / discharge mechanical OFF push buttons for emergency trip (shrouded) test /

service position limit

Digitally signed by A

switches with 6 NO / 6 NC breaker auxliary contacts in service position.The busbars shall be

rated for continuous

current, at 40°C ambient temperature. Temperature rise shall be as per IEC 62271-200.

The bus bars shall be sleeved for full voltage. Sleeve shall be heat shrinkable BTPM type of

Reychem / equivelent

make. No PVC sleeving in bus bar for 11KV is acceptable

CT chamber with Dual core, single phase, Single ratio cast resin CT, 15VA burden with core-1

for metering (CL-

1) ,core-2 for protection (CL-5P10) Digital Ammeter with selector switch, shrouded terminals,

square size.The busbars shall be located in a separate

metal clad chamber and shall be air insulated. Bus bars shall be extendible on either side

Microprocessor based IDMT instantaneous relay with 3 O/C (50-200%) & one E/F protection

maintain safety of the Indoor switchgear & Human resources in case of any internal ARC fault

and also minimize

the damage, maintenance cost and downtime of the system, the system should have ARC flash

protection system

with ACTIVE Arc flash protection

Antipumping relay & master trip relay

A set of breaker ON/OFF/Trip/DC control supply/Trip circuit healthy & R,Y, B phase indication

Required Auxiliary relays for WTI (Winding temperature indication with alarm & trip)

6-window annunciation panel with audio and visual indication

Over current & earth fault - 2 windows Winding temperature trip alarm - 2 window

Master trip operated - 1 window

Spare window - 2 1 Set

Emergency trip push button on front door 1 Set/Panel

Limit switches with 6 NO/ 6 NC breaker auxiliary contacts 1 Set/Panel

Control:- T-N-C (Trip, Neutral, Close) breaker control switch. 1 Set/Panel

All control wiring with protection & test terminal block as required. 1 Set/Panel

Space heater with thermostat for moisture absorption. 1 Set/Panel

Cable box suitable for connection for 3C x 300sq.mm 33KV XLPE Al. conductor cable.1 set/pan

HT Danger Plate 1 Set/Panel

50X5 mm Copper earth bus to be provided for full length of the panel

Outgoing as described above. 2 SET

HT Panel as described above (1 No.Incoming / 2 No Outgoing Panel) set 1 ₹ 3,743,081.49 ₹ 3,743,081.49

1000 kVA Transformer

24.6 Supply, installation, testing and commissioning of following capacity

(continuous loading) BEE 5 Star rated (Corresponding Level as per BIS

amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase,

50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound

transformer (Electrolytic grade 99.9% pure copper, Core made of first

grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better,

suitable for out door/indoor applications with On Load Tap Changer (OLTC)

on HV side having AVR relay and Remote Tap Changer Control (RTCC) for

automatic sensing of incoming voltage, automatic operation of OLTC and

facility for remote and manual operation of OLTC HV side in range of +5% to

Digitally signed by A

-15% in steps of 2.5%, having cable end boxes on HV side suitable for

3x300 sqmm XLPE cable of 11 KV grade, including bus trunking

arrangement on LV side including supplying and laying of copper conductor

multicore control cable from transformer to HT breaker/panel for safety

tripping, complete with all accessories and safety provisions as per relevant

IS Code including first filling of filtered dehydrated oil, i/c supplying and

grouting of suitable M.S. Channel with all accessories and transformer shall

be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked and

as per CPWD specifications complete in all respects etc as required at site.

The maximum flux density in any part of the core and yoke at rated voltage

and frequency shall be such that the flux density with + 12.5 percent

combined voltage and frequency variation from rated voltage and frequency

does not exceed 1.9 Tesla. The permissible temperature-rise shall not

exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40 dg.C for oil and 45

dg. C for above 200 KVA for winding. Inside of tank shall be painted with

varnish or liquid resistant paint. For external surfaces one coat of thermo

setting powder paint or one coat of epoxy primer followed by two coats of

polyurethane base paint shallbe used. IS: 1180 (Part 3) shall be referred to

for paint thickness for normal to medium corrosive atmosphere. For highly

polluted atmosphere and special application external paint work shall be as

per direction of Engineer-in-Charge. Design ambient condition : a) air

temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as

per location of site, d) Altitude as per location/site. Noise level Shall not

exceed limits as per NEMA TR-1 with all accessories running measured as

per IEC 551 / NEMA standard. The transformer should have QR code which

should contain drawing, test report OEM manual,Geo- Tag of manufacturing

location etc. Marking Each transformer shall be provided with rating plate

made of anodized aluminum/ stainless steel material securely fixed on the

outer body, easily accessible,as per IS: 1180 Part-3. The entries on the rating

plate shall be indelibly marked.

Fitting and Accessories : The following fittings shall be provided:- a) Two

earthing terminals with the earthing symbol b) Oil level gauge indicating oil

level at minimum, 30°C and maximum operating temperature; c) Air release

device (for non-sealed type transformers) d) Rating and terminal marking

plates; e) Silica gel breather f) Drain-cum-sampling valve (¾″ nominal size

thread, IS 554) preferably steel with plug for three phase transformers; g)

Thermometer pocket with cap; h) Oil filling holes having (1¼″ nominal size

thread) with cover (for sealed type transformers without conservator); i)

Lifting lugs for the complete transformer as well as for core and winding

assembly; j) Pressure relief device or explosion vent above 200 kVA; k) One

filter valve on the upper side of the tank (for transformers above 200 kVA); l)

Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection

hole (for transformers above 200 kVA); n) HV side neutral grounding strip

(where one of the HV bushing terminal is connected to earth);

o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or

suitable rating lightning arrestors for HT side – 3 Nos. q) Bird guard; r) Oil

temperature indicator and winding temperature indicators for transformers

above 200 kVA with suitable tripping mechanism above permissible limit s)

Jacking pads (for transformer above 1600 kVA); t) Additional Neutral

separately brought out on bushing for earthing. u) Magnetic oil level gauge

Digitally signed by A

(for transformer above 1600 kVA) with low oil level alarm contact; v) Non

return valve (for conducting pressure test); w) Pressure relief device or

explosion vent x). Monogram Plate y) Inspection cover z). Detachable type

radiators with top and bottom shutoff valve. aa) Oil Conservator with Oil level

indicator, minimum level marking and drain plug for all transformers of

capacity 50 KVA and above. bb) Necessary hardware, clamps, lugs etc. for

termination on HV/MV etc. for all transformers.

24.6.1 1000 kVA transformer Each

NS-3.3 LT panel FRONT OPERATED PANEL

Design, manufacture, supplying fixing in position of the following front operated

cubicle type,compartmentalised with front access, dead back, 2mm thick steel

enclosed free standing, dust and vermin proof, switchboard with IP42 protection

with hinged and lockable doors complete with interconnections, tinned copper

crimping lugs, bonding to earth and painting, suitable for use at 415 volts, 3 phase 4

wire 50 Hertz system, and suitable for a fault level of 35 KA symmetrical at 415

All switchboards shall be modular type and have provision for entry of cables from the top

/bottom as required

The cost shall include providing and fixing of 100 x 50 x 6 mm channels for switchboard support.

All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The

Busbars insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports

All MCCB shall have phase barriers, rotary handles and extension terminal as required .

All unbalanced kWH meter shall have communication module for BMS connectivity

Original test certificate of the MCCB as per IEC 60947-1 &2 or IS13947 shall be furnished

Pre-commissioning tests on the switch board panel incorporating the MCCB shall be done as per

specifications.

MCCBs with ratings up to 250 A shall be equipped with Thermal-magnetic (thermal for overload

and magnetic for short-circuit protection) trip units

Microprocessor MCCBs with ratings 250A and above shall be equipped with microprocessor

based trip units. (both variable setting)

Microprocessor and thermal-magnetic trip units shall be adjustable and it shall be possible to fit

lead seals to prevent unauthorized access to the settings

Microprocessor trip units shall comply with appendix F of IEC 60947-2 standard (measurement

of rms current values, electromagnetic compatibility, etc.)

LT PANEL &DISTRIBUTION PANEL WORK

ALL LT PANELS SPECIFIC INCLUSIONS:

The outgoing feeders as indicated in SLD shall have suitable range of followings (except

capacitor feeders).

All ACB's shall be suitable for minimum 50 kA as specified in the items (Icu=Ics=Icw for 1 sec.)

Digitally signed by A

All MCCB's shall be suitable for unless otherwise specified in the item (Icu=Ics= 1 sec=100%.)

All incoming as well as outgoing feeders shall have pad locking facility.

Suitable danger board shall be provided.

All MCCB’s shall be provided with front rotary handle and operating mechanism for door

interlock with Pad locking of MCCB’s handles in “OFF” Position.

The Panel fabricator shall provide Al Bus-bars link from Breakers wherever more than two

nos. of cables are terminated in the breakers.

All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in

single tier formation.

All distribution sub panels shall be provided with class 1.0 accuracy meters as well as CTs.

All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.

Panels shall be Powder Coated with Siemens grey paint shade no. RAL- 7032 of IS-5.

All motor feeders MCCBs shall be of motor duty.

Supporting/Base rigid steel framework.

4P ACB’s / MCCB’s shall mean 4 pole ACB’s / MCCB’s with adequate size of neutral link.

All MCCB above 250A shall be microprocessor base.

Marking of Switchgear busbars IS 11353 : 1985

Degree of Protection of Enclosures for low voltage switchgear. IEC 60529

Electrical relays for power system protection IS 3231 : 1986

Code of Practice for selection, installation and Maintenance of switchgear &controlgear IS 10118

Low voltage switchgear &controlgear assemblies IEC 60349

Danger notice plates IS 2551 : 1982

The ACB shall confirm to the requirements of IEC 60947-2 &3 (FOR SWITCH

DISCONNECTION) / IS 13947-2 and shall be type tested &certified for compliance to

standards from–CPRI, ERDA/ any accredited international lab. The circuit breaker shall be

suitable for 415 V + 10%, 50 Hz supply system. Air Circuit Breakers shall be with moulded

housing flush front, draw out type and shall be provided with a trip free manual operating

mechanism or as indicated in drawings and bill of quantities with mechanical

"ON""OFF"“TRIP” indications.

ACB shall confirm compliance to ROHS/WEEE guidelines

Racking Interlock in Connected/Test/Disconnected Position.

Service Position : Main Isolating contacts and control contacts of the breaker

Test Position : Main Isolating contacts are isolated but control contacts

are still engaged.

Isolated Position : Both main isolating and control contacts are isolated.

Withdrawal or engagement of Circuit breaker shall not be possible unless it is in open

Operation of Circuit breaker shall not be possible unless it is fully in service, test or

drawn out position

c) All modules shall be provided with safety shutters operated automatically by movement

of the carriage to cover exposed live parts when the module is withdrawn.

d) All Switchgear module front covers shall have provision for locking.

e) Switchgear operating handles shall be provided with arrangement for locking in ‘OFF’

Digitally signed by A

The breaker should be equipped with micro-controller based release to offer accurate and

versatile protection with complete flexibility and shall offer complete over current protection

to the electrical system in the following four zones :

a) Long time protection.

b) Short time protection with intentional delay.

c) Instantaneous protection.

d) Ground fault protection.

Derating factor- There shall not be any derating up to 50 degree. Manufactures

shall provided the derating table/chart

3.3.2.9 4P ACB shall have 100% Neutral as same of Phase conductor with protection

setting (setting of 50%,100% and Off)

ACB release shall have inbuilt “Auto protection” against excessive heating at terminals.

The MCCB should be current limiting type with trip time of less than 10 msec under short

circuit conditions. The MCCB should be either 3 or 4 poles as specified in BOQ. MCCB

shall comply with the requirements of the relevant standards IEC 60947-2 and should

have test certificates for Breaking capacities (Ics=Icu=100%) from independent test

authorities CPRI / ERDA or any accredited international lab.

MCCB shall comply with “Class-II front facia as per IEC 61140”

The MCCB shall employ maintenance free minimum let-through energies and capable of

discrimination up to the full short circuit capacity of the downstream MCCB. The manufacturer

provide both the discrimination tables and let-through energy curves for all. It shall be respo

Microprocessor MCCBs with ratings 250A and above shall be equipped with microprocessor

based trip units.

(both variable setting)

Original test certificate of the MCCB as per IEC 60947-1 &2 or IS13947 shall be furnished

Surge Protection Devices ( SPD’S) shall be provided at main LT Panel incoming feeders

(Stage I / Class B) &Distribution Boards (Stage II / Class C) for the protection of Building

electrical and Electronics system from the effect of Lightning discharges, line induced

transient surge voltage or switching surges as per the details mentioned in the BOQ.

The Switchboards shall be of adequate size with a provision of 25% spare space to

accommodate possible future additional switch gear.

5.1 A base channel 75 mm x 5 mm thick shall be provided at the bottom.

5.2 A minimum of 200 mm blank space between the floor of switchboard and bottom most unit

shall be provided.

5.3 The overall height of the switchboard shall be limited to 2300 mm unless otherwise

5.4 The height of the operating handle, push buttons etc shall be restricted between 300 mm

and 2000 mm from finished floor level.

Digitally signed by A

Switchboard Bus Bars

8.1 Busbars shall be made of high conductivity, high strength aluminium alloy, complying with

requirements of grade E 91E of IS 5082 – 1981. Design of busbar system shall comply to

IS 5578 and IS 11353. Busbars shall be of rectangular cross sections suitable for full load

current for phase bus bars as also neutral bus bar . The maximum current density shall be

1 amp per Sq. mm. Busbar shall be suitable to withstand the stresses of fault level as

specified in schedule of quantities.

12.1 All wiring for relays and meters shall be with PVC insulated copper conductor wires. The

wiring shall be coded and labelled with approved ferrules for identification. The minimum

size of copper conductor control wires shall be 2.5 sq. mm.

12.2 Wiring shall be terminated with ferrules on terminal block. CTs shall be provided with

shorting facilities

Continuous internal earth bus sized for prospective fault current to be provided with

arrangement for connecting to station earth at two points. Hinged doors / frames to be

connected to earth through adequately sized flexible braids.

Suitable engraved white on black name plates and identification labels of metal for all

Switchboards and Circuits shall be provided. These shall indicate the feeder number and

feeder designation.

Switchboard configurations offered shall be CPRI tested. Copies of the CPRI test

certificates shall be submitted with the tender

Application guide for Current Transformers IS 4201 :

Application guide for Voltage Transformers IS 4140 :

Application guide for Relays IS 3842 :

Electromagnetic Relays IS 5051 :

Each C/T shall be

provided with rating plate indicating:

a) Name and make

b) Serial number

c) Transformation ratio

d) Rated burden

e) Rated voltage

f) Accuracy class

MAIN LT PANELS WITH ACB's

Digitally signed by A

Supply, installation, testing &commissioning of cubical type LT panel suitable for 415V, 3

phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized (preferably) design from

CRCA sheet steel of 2 mm thick for frame work & covers, 3mm thick for gland, plates i/c

cleaning &finishing complete with 7 tank process for power coating in approved shade, having

2000 Amp capacity extensible type TPN aluminium alloy busbar of high conductivity,

DMC/SMC bus bar of high conductivity, DMC/SMC bus bar supports, with short circuit

withstand capacity of 31 MVA for 1 second, fabrication shall be done in transportable sections,

entire panel shall have common earth bar of size 50 mm x 5 mm at the rear with 2 nos. earth

stud, solid connections from main busbar to switch gears with required size of Al. bus bars and

control wiring with 2.5sqmm PVC insulated copper conductor S/C cable, cable alleys,

cable gland plates in two half, i/c providing following switch gears.

(Note: The contractor may select the next higher fault rating of ACB/MCCB if it is not

readily available ,without any extra cost.)

From 1000 KVA Transformer

2 Nos. of 1600 A, 4P electrically operated Drawout type ACB with

Ics=Ics=50KA having Mircroprocessor based releases for O/L, S/C &E/F protection.

2 Nos. SPD Type-1, 50kA

2 Sets - digital multifunction meter (showing harmonics along with all other electrical

parameters such as voltage, current, Hz, KW, KWHr, PF.) with RS 485 port with matching

cast resin CT's

2 Sets - 0-500V, digital Voltmeter with selector switch, 3 No. phase indicating LED lamp

to show the incoming power with control SP MCB.

2 Sets indicating LED lamps for ACB On/Off/ Trip/Trip circuit healthy/spring chagre,

Emergency stop, Auto/manual selector switch with protective SP MCB's.

6 Sets of CTs of the ratio 1600/1A, Class-2S for APFC Relay, Burden 15 VA

6 Sets of CTs of the ratio 1600/1A with Class 2S Accuracy for Metering, burden 15 VA

6 Sets. 1600/1A , 15 VA, Class-5P10 CT's for Protection

2 No. Under Voltage relay, over voltage, phase sequence, 46,86,95,50BF relay

2 no 8W announciator

From Existing Panel

1 Nos. of 1000 A, 4P electrically operated Drawout type ACB with

Ics=Ics=35KA having Mircroprocessor based releases for O/L, S/C &E/F protection.

1 Sets - digital multifunction meter (showing harmonics along with all other electrical

parameters such as voltage, current, Hz, KW, KWHr, PF.) with RS 485 port with matching

cast resin CT's

1 Sets - 0-500V, digital Voltmeter with selector switch, 3 No. phase indicating LED lamp

to show the incoming power with control SP MCB.

1 Sets indicating LED lamps for ACB On/Off/ Trip/Trip circuit healthy/spring chagre,

Emergency stop, Auto/manual selector switch with protective SP MCB's.

3 Sets of CTs of the ratio 1000/5A with Class 5P10 Accuracy for Metering, burden 15 VA

3 Sets of CTs of the ratio 1600/1A with Class 2S Accuracy for Metering, burden 15 VA

1 No. Under Voltage relay, over voltage, phase sequence relay

DG Set (750kVA)

Digitally signed by A

2 Nos. of 1000 A, 4P electrically operated Drawout type ACB with

Ics=Ics=50KA having Mircroprocessor based releases for O/L, S/C &E/F protection.

2 Sets - digital multifunction meter (showing harmonics along with all other electrical

parameters such as voltage, current, Hz, KW, KWHr, PF.) with RS 485 port with matching

cast resin CT's

2 Sets - 0-500V, Voltmeter

2 Sets indicating LED lamps for ACB On/Off/ Trip/Trip circuit healthy/spring chagre,

Emergency stop, Auto/manual selector switch with protective SP MCB's.

6 Sets of CTs of the ratio 1000/1A with Class 2S Accuracy for Metering, burden 15 VA

6 Sets. 1600/1A , 15 VA, Class-5P10 CT's for Protection

2 No. Under Voltage relay, over voltage, phase sequence, 51,86,50N,51N,32,51NS,86 relay

AUTO START / AUTO STOP & AUTO / MANUAL LOAD SHARING,

LOAD MANAGEMENT THROUGH PLC

ii) 1 set Power Supply 10A, 12/24V DC with built in EMI filter

iii) 1 set Aux. / Control relays with 4 C/O , 12/24V DC

iv) 2 sets Engine Start / Stop Relays 12/24V DC

v) 2 sets Emergency Stop push buttons (Mushroom type)

vi) 2 set Start / Stop push buttons

vii) Lot - Indicating lights(LED TYPE)

viii) 1 No. ON LINE UPS with SMF Battery with suitable capacity

ix) 1 set Control relays 240 V AC

x) Lot - Control MCB 2A SP

xi) Lot- Power MCB 16A /6A

xii) Lot-Control terminals

xiii) 2 Nos. Power Sockets 16A / 3 pin

xiv) 2 Nos. selector switch 6A, Auto / Manual & DG selection (for 3 nos.

xv) 1 No. DC supply healthy indicating light

xvi) 1 No.DC Failure indicating light with alarm

BATTERY CHARGER:- (For DG Sets)

2 Sets 12/24V DC Battery charger having proterction of over Voltage /

Under voltage / Over charging. Battery charger shall be comptele with

DC ammeter , DC Voltmeter & LED indicating lamps as required.

Note Any additional component/ device (Including UPS, Powersupply,

power pack) required for proper operation of control/

/ interlocking scheme shall be considered by Panel

manufacturer without any additional cost.

TPN aluminium bus bars of minimum of 2000 Amps capacity with heat shrinkable coloured

sleeves and i/c DMC/SMC bus bar cross section, size supports &their spacing etc. for

withstanding fault level of 31 MVA for 1 sec.

Digitally signed by A

1 No. of 1600 A, 4P electrically operated Drawout type ACB with Ics=Ics=50KA having

Mircroprocessor based releases for O/L, S/C &E/F protection.

1 Set of Breaker ON-OFF indication Lamps as required.

Electrical through advance contacts in MCCB/ACB's (Incomer & bus couplers)

&mechanical (castel key) interlocking should be provided to ensure that only one supply is

available at a time on each section of bus & to eliminate any possibility of accidentlly

approaching two supplies at one bus section.

all outgoing feeder must have ON/OFF/Trip indication, Multifunction meter and CTs

OUTGOINGS-Bus Section-1

1 No. 630A FP MCCB (35 KA) For 325 KVAR Capacitor Panel 1

1 Nos. 1600A 4P ACB (50 KA) For Auditorium Panel

1 Nos. 400A 4P MCCB (25 KA)

OUTGOINGS-Bus Section-2

1 No. 630A FP MCCB (35 KA) For 325 KVAR Capacitor Panel 2

1 Nos. 800A 4P ACB (50 KA) For Academic Panel

1 No. 630A FP MCCB (35 KA) For Lab

1 Nos. 800A 4P ACB (50 KA)

1 Nos. 200A 4P MCCB (25 KA)

PLC FEEDER- FOR LOAD MANAGEMENT &E/M INTERLOCKING :

Hardware using PLCs for Monitoring of all Electrical Software and for operations,

controlling and interlocking Parameters of 2 Nos. I/C from Transformer, 2 Nos. I/C from DG,

& 1 Nos. I/C from existing panel with Window based software &Engineering &

Software Development. Required Aux. Relays, Push Buttons &Indication lamps, 2KVA UPS

for Black start &maintenance free Batteries, Power monitors, Programmable Logic

controller, Annunciator and status Fascia, MIMIC with LED circuit etc as required completing

The Switchboard with Logic control panel shall be complete with all interconnections,

risers, internal wiring, labels, control/circuit fuses etc. complete as required.

Note: Incomer from LT Supply, DG, existing panel & Bus coupler shall be electrically

&mechanically interlocked.

Main LT Panel as described above Each 1 ₹ 4,389,482.87 ₹ 4,389,482.87

NS-3.4 APFC Panel (325kVAr)

Supply, Installation, testing and commissioning of

Automatic Power Factor Correction (APFC) panel,

indoor type floor mounted free standing totally

enclosed, extendable, IP 42, of following capacity for

3 phase, 415 V + 10 %, 50 Hz AC System for

Ambient temperature -5°C to +40°C, fabricated in

compartmentalised designed made of CRCA sheet

steel of 2.0mm thick for framework & covers, 3 mm

Digitally signed by A

thick for gland plate i/c cleaning & finishing complete

with 9 tank process for powder coated of approved

shade ( RAL 7032-Siemens Gray or as approved by

Engineer-in-Charge), having front section (switch gear

and control accessories) and rear section capacitor

and reactor, front and rear access, having suitable

current carrying capacity, extensible TPN Aluminium

alloy bus bar of high conductivity, DMC/SMC bus bar

supports, bottom base channel of MS Section,

fabrication shall be done in transportable section,

entire panel shall have common copper earth bar of

minimum size of 25mm x 5mm with 2 nos. earth

studs, the earth terminals provided on the body of

capacitor bank shall also be bonded to the main

capacitor panel earth bus with 2 nos. 8 SWG or 6

SWG GI earth wires/ equivalent size of copper

conductor cable, forced ventilation for maintaining

temperature rise not more than 5°C from ambient,

interconnections, connections with 14% detuned

reactor and heavy duty 525 V ISI marked Impregnated

MPP(Metalized Polypropylene) Capacitor (IS 13340

Part -1 & 2) APFC Panel shall be in compliance with

IS :16636 & CPWD Specifications etc.

as per below details.

630A FP MCCB Microprocessor base with

O/C, S/C, E/L release of TPN 50KA breaking capacity

(Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating

Lamp set along with required Instruments and

accessories with extended rotary handle and door

interlocking arrangement. Current rating of the

Incomer in ampere shall be APFC Panel rating in

KVAR x 1.4 x 1.5 or Nearest higher standards rating.

(B) Instruments & Indications

i) 3-Phase current sensing APFC microprocessor

relay/controller , advance 8/12 stages (8 stages for

capacity below 100 KVAR and 12 stages 100 KVAR &

above) with Communication Ethernet/RS485/SNMP

port open protocol for BMS integration as per

approved by Engineering in charge and having

display of Phase wise V, A, PF, Cos-Phi, Kw, KVA,

KVAR, THD-V , THD-I, harmonics up to 31 level. 3

nos of dual core CT's accuracy class 1, 15VA at

incomer of PCC Panel for APFC relay.

ii) Auto Manual Selector switch, auxiliary contactors

with timer for delay in manual mode.

iii) Digital Multi function meter with LED Display for V,

A, PF, KW, KVA, KVAR, THD-V & I, Frequency.

iv) Suitable rating control transformer shall be provided

for control and indication circuit.

Digitally signed by A

v) All components like control transformer, meter, relay

and indicating lamp shall be protected by using

suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using

2.5 sq mm, FRLS/HFFR 1100 V grade, PVC insulated

multi stranded copper control wire.

(C) Bus Bars 1 Amp per Sq.mm,TPN, Electrolytic

grade Aluminium bus bar of capacity 1.25 times of

incomer rating as per CPWD specification.

(D) Outgoings (APFC Section) Selection of the

capacitors combinations shall be for continuous

rating and each capacitor bank shall have suitable

capacity Heavy Duty ISI Marked Capacitor, capacitor

duty contactor,the capacitor shall be mounted on

channel with base of perforated M S Powder coated

sheet, connections inter connections etc. and other

features as per CPWD Specifications and relevant IS

Code having following:

(i) Capacitor bank ratings & stages shall be as per the

technical specifications sheet of NIT.

(ii) Capacitor will be MPP self healing type with

discharge resistor, pressure release mechanism.

(iii) Since Capacitor Voltage is 525 Volts, thus higher

KVAR has to be considered to get rated output at 415

(iv) 14% Detuned Reactor of class H insulation &

150% linearity in series with Capacitor.

5KVAR, 10KVAR,10KVAR, 25KVAR, 25KVAR, 50KVAR, 100KVAR,100KVAR

HT cable, Termination and Laying

Supply&LayingofnonskidElectromat1mtrwideand3.0mmthick11KVgradeconformingtoIS15652as

requiredincluding cutting to required length complete as per requirement of local electricity 20 ₹ 10,526.70 ₹ 210,533.94

NS-3.5 authorities. RM

Supplying,Receiving, shifting, andcommissioningof followingsizesof 11KVgradeXLPE

insulatedaluminiumconductor armouredpowercablesconformingtoIS:7098(Part-II)

laidburiedinground/ trench/existingHumepipe/PVCpipe/GIpipe inanapprovedmanner completeas

requiredandasper specifications includingexcavationof trench inall classesof soil,

includingsupplyandprovisionof sandbedabove thecableandbelowthecablewithsupplyand layingof

1st classbrick protectionbackfillingof thetrenchwithexcavatedearthfreefrombouldersafter

layinganddressingof thecableinanapproved manner complete as required as per IS1255 and as per

NS-3.6 drawing.

Laying of one number XLPE power cable of 11KV grade of following size in the existing

DSR-22.4 masonry open duct as required

22.4.2 a. Above 120 sq. mm and upto 400 sq. mm meter 200 ₹ 146.00 ₹ 29,200.00

Digitally signed by A

Supplyingandmakingindoorcableendterminationwithheatshrinkablejointingkitcompletewithallacce

ssoriesincludinglugs suitable for following size of 3 core, XLPE aluminium conductor cable of

DSR-23.4 11 KV grade as required :

Supplyingandmakingoutdoorcableendterminationwithheat shrinkable jointingkit

completewithallaccessories including lugs suitable for following size of 3 core, XLPE aluminium

DSR-23.5 conductor cable of 11 KV grade as required :

DSR-15.14 Providing, laying and fixing following dia RCC pipe

NP2 class (light duty) in ground complete with RCC

collars, jointing with cement mortar 1:2 (1 cement : 2

fine sand) including trenching (75 cm deep) and

refilling etc as required.

LT cable, termination, Laying

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of

10.6 following size in the existing masonry open duct as required.

10.6.2 Above 35 sq. mm and upto 95 sq. mm

10.6.4 Above 185 sq. mm and upto 400 sq. mm meter 850 ₹ 146.00 ₹ 124,100.00

Supplying and making end termination with brass compression gland and aluminium lugs for

following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

11.1 KV grade as required

11.1.24 3.5C X 95 Sqmm Aluminium Cable each 4 ₹ 684.00 ₹ 2,736.00

11.1.22 3.5C X 50 Sqmm Aluminium Cable each 2 ₹ 484.00 ₹ 968.00

11.1.34 4C X 25 Sqmm Aluminium Cable each 14 ₹ 373.00 ₹ 5,222.00

Supply, following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor/copper

NS-3.7 conductor power/ multicore control armoured cable of 1.1 KV grade.

NS-3.7.1 3.5C X 300 Sqmm Aluminium Cable meter 850 ₹ 2,353.27 ₹ 2,000,278.39

NS-3.7.2 3.5C X 95 Sqmm Aluminium Cable meter 360 ₹ 837.49 ₹ 301,495.25

NS-3.7.3 3.5C X 50 Sqmm Aluminium Cable meter 120 ₹ 636.77 ₹ 76,412.02

NS-3.7.4 4C X 25 Sqmm Aluminium Cable meter 840 ₹ 474.81 ₹ 398,837.51

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and

providing masonry enclosure with cover plate having locking arrangement and watering pipe of 14 ₹ 8,351.00 ₹ 116,914.00

5.4 2.7 metre long etc. with charcoal/ coke and salt as required. each

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

providing masonry enclosure with cover plate having locking arrangement and watering pipe of 14 ₹ 15,004.00 ₹ 210,056.00

5.6 2.7 metre long etc. with charcoal/ coke and salt as required. each

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode 300 ₹ 1,638.00 ₹ 491,400.00

5.10 including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. meter

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode 260 ₹ 755.00 ₹ 196,300.00

5.11 including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. meter

Digitally signed by A

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as

5.14 required. meter

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

5.15 required. meter

29.1.17 DG set (750kVA)

Supplying, Installation, Testing & Commissioning of

‘Silent Type Diesel Generating set as per CPCB IV +

or better norms along with having Prime Power Rating

of KVA as below, 415 volts at 1500 RPM, 0.8 lagging

power factor at 415 V suitable for 50 Hz, 3 phase

system & for 0.85 Load Factor, including testing at

factory and site with fuel, load for test and other

necessary arrangements Complete as per CPWD

specifications, should have QR code which should

contain drawing, test report OEM manual,Geo- Tag of

manufacturing location, rating plate as per relevant IS

Code etc. and consisting of the followings:

(A) Diesel Engine:

Tourbocharged Diesel engine 4 stroke water cooled,

multi cylinder, dynamically balanced fly wheel, electric

start of suitable BHP at 1500 RPM suitable for above

output of alternator at 40 0C, 50% RH & at 1000 Meter

MSL , capable of taking 10% over loading for one hour

after 12 hours of continuous operation. The engine will

be with Electronic governor, Dry type Air filter with

service indicator, first filling of engine fuel (after

commissioning) lubricating Oil, Coolant and other

consumables complete with all the required

accessories, the Electronic governor shall be as per

ISO 8528.The engine shall comply to the latest CPCB

norms (CPCB IV + or better) and Conforming to BS

per CPWD specifications.

(B) Engine mounted Instrument Panel fitted with and

having digital dis Plate for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(C) Alternator:

Synchronous alternator rated of appropriate KVA, 415

volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8

lagging power factor at 40 0C, 50% RH & at 1000

Digitally signed by A

Meter MSL. The alternator shall be having Screen

Protected Drip Proof (SPDP) enclosure IP23,

brushless, continuous duty, dynamically balanced

rotor, capable of taking 10% over loading for one hour

after 12 hours of continuous operation, self

cooled,self-excited and self-regulated through AVR

conforming to IS13364(Part 2)/IS: 4722/BS 2613

suitable for tropical conditions and with class- H

(D) Base Frame & Foundation:

Both the engine and alternator shall be mounted on

suitable base frame made of MS channel with

necessary reinforcement which shall be installed on

suitable cement concrete foundation and vibration

isolation arrangement as per recommendations of

Daily service fuel tank of suitable liters capacity as per

CPWD Specifications, fabricated out of 3 mm thick

M.S. sheet complete with all standard accessories and

fuel piping between fuel tank and diesel engine with

MS class ‘C’ pipes of suitable dia. Complete with

valves, level indications & accessories as required as

per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital type exhaust

silencer and catalytic convertor.

(G) Starting System:

12V/24V DC starting system comprising of starter

motors: voltage regulator and arrangement for initial

excitation complete with suitable numbers of batteries

(180 AH capacity lead acid SMF type) as required as

per specifications. The battery shall be housed inside

the acoustic enclosure of DG Set.

(H) Acoustic and weather proof enclosure with

arrangement for fresh air intake for cooling of the

engine & alternator, extraction, discharging hot air in to

the atmosphere and the temperature rise inside the

enclosure, noise level outside enclosure. The acoustic

enclosure should be suitable for cable

connection/connection through bus-trunking. Such

arrangements on acoustic enclosure should be water

proof & dust-proof conforming to IP-65 protection. The

enclosure shall be as per CPCB IV + or better norms

etc. and as per CPWD specifications.

Free standing floor mounted IP 42 automatic mains

failure control panel including auto by-pass, suitable

for KVA as below for silent type DG set complete with

relays, timers, set of CTs for metering & protection and

Digitally signed by A

energy analyser to indicate currents, phase and line

voltages, frequency, power factor, KWH, Kilo Volt

Ampere Reative Hour (KVARH), KVA (Phase & Total),

KW & provision for overload, short circuit, restricted

earth fault, under frequency, power (aluminium) and

control (copper ) cabling of suitable size upto 15 meter

between AMF panel, LT Panel and DG Set including

connection interconnection etc. as required, all

complete and inter locking and communication/

Ethernet /RS485/SNMP port open protocol for BMS

integration including suitable software, the panel shall

be of DG Set OEM make etc. as per approved by

Engineering in charge and including the following:

1. Suitable numbers and appropriate capacity 4 pole

motorised electrically operated draw out with cradle

type 3 position ACB/ MCCB with electronic release for

O/C & E/F and shunt trip.

2. Auto/Manual/Test/Off selector switch

3. Protection for under and over voltage phase

reversal (2 nos Over voltage relay, 2 Nos. reverse

power relay and 2 Nos. under voltage relay).

4. 3 Sets of current transformers 15 P 10 accuracy for

protection and 15 VA class-I for metering

5. Energy analyser unit to indicate current, Voltage( LN

& L_L), kW, kVA (Phase & Total), Frequency, KWH,

6. LED Indicating lamps for load on mains and load on

7. Fuse/ MCB for instruments

8. Battery charger, complete with transformer/ rectifier,

D.C. voltmeter and ammeter, selector switch for

trickle, off and boost and current adjustment.

9. Main supply failure monitor

10. Supply failure timer

11. Restoration timer

12. Control unit with three impulse automatic engine

start/stop and failure to start lockout.

13. Impulse counter with locking and reset facility.

14. ON/OFF/Control circuit switch with indicator

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC

sensing, Over Current, Unbalancing load with suitable

number of relays and accessories

17. Maintenance notification based on Engine Run

Hour & due date.

Digitally signed by A

18. Load Management through PLC to achieve auto

opening and closing of incomer breakers, bus coupler

switching of essential panel , interlocking providing

signal to AMF Panel for load status and AMF shall

give command to DG Set to auto start / auto stop

depending upon load status and requirement etc. and

necessary hardware and software required to perform

the operation shall be provided by the contractor

including all control wiring.

Supplying and fixing Exhaust gas piping of 1x300 dia. welded black MS, C Class pipe

conforming to IS:1239 and installed with necessary bends, supports and clamps, anti-vibration

NS-3.8 mountings, insulation of

exhaust system with mineral wool/Rockwool, 50 mm thick wire mesh & aluminum cladding etc.,

as required as per specifications. meter

Total of Sub-Head -III carried to summary sheet ₹ 13,267,510.00 ₹ 16,939,062.80

Sub Head: IV SUB STATION LIGHT WIRING ETC

Distribution Board

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board,

240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5A to 32A rating, 240/415 volts, "C" curve, miniature circuit breaker

2.10 suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Internal Wiring

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed steel conduit, with modular

switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC

insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point

(without independent switch etc.) with1.5 sq. mm FRLS PVC insulated copper conductor single

core cable in surface/ recessed steel conduit, and earthing the pointwith 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable etc. as required.

Digitally signed by A

Wiring for twin control light point with 1.5 sq.nn. FRLS PVC insulated copper conductor single

core cable in surface/recessed steel conduit, 2 way modular switch,modular plate,suitable GI Box

and earthing the point with 1.5 sq.mm. FRLS PVC insulated coper conductor single core cable

etc.as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

1.7 insulated copper conductor, single core cable in surface/ recessed Steel conduit as required

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Meter 0.00 ₹ 476.00 ₹ 0.00

1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Meter 0.00 ₹ 652.00 ₹ 0.00

1.7.10 4 x 10 sq.mm + 2 x 6 sq.mm. earth wire Meter 0.00 ₹ 1,253.00 ₹ 0.00

1.7.11 4 x 16 sq.mm + 2 x 6 sq.mm. earth wire Meter 0.00 ₹ 1,760.00 ₹ 0.00

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in

1.31 recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps Each 6 ₹ 545.00 ₹ 3,270.00

modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in

1.32 recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 Each 4 ₹ 659.00 ₹ 2,636.00

amps modular switch, connection etc. as required.

LED Batten light (System lumen efficacy ≥120 85%, Operating voltage AC 140 270 Volt,

frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV

with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free

(flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000

Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K /

5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation

Colour Matching) <3, Maximum power consumption

should not more than the specified rating and

Fixture shall be of relevant BIS standard.

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete

in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper

8.1 conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty.

System lumen efficacy ≥120 <135 lm/Watt output .

LM79 & LM80 Test report and all testing required

for LED fixtures as per BIS shall be submitted.

Shape size and CCT shall be as approved by

Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing

such that LED junction temperature shall not rise

above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Supplying of MS Body Exhaust Fan heavy duty 230V A.C 50 cycles, 600 mm sweep, 900 rpm,

energy efficient, complete

erected in position with 16A 3 Pin Plug Top in the existing opening, including making good the

damage, connection, testing,

commissioning etc. as required. Each 5 ₹ 13,205.88 ₹ 66,029.40

Digitally signed by A

Brush Less Direct Current (BLDC) Fan with Remote Supply, Installation, Testing and

Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation:

B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit,

safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value

(CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total

9.1 Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and

all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.),

insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply

Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR,

PVC insulated copper conductor single core cable and earthing etc. as required.

9.1.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Each 2 ₹ 2,882.00 ₹ 5,764.00

Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in

recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, Each 30 ₹ 807.00 ₹ 24,210.00

"C" curve including connections, painting etc. as required.

26.1. Online UPS - Input supply: Single Phase, Output

Supply: Single Phase.

Supplying, installation, Testing & Commissioning of

following capacity at full load (Unity Power Factor)

ON LINE Uninterrupted Power Supply (UPS)

system suitable for Single Phase input, Single

Phase output AC Supply. The UPS shall include a

Rectifier, inverter, battery bank suitable for 30

minutes back up (Battery VAH capacity shall not be

less than 1600 VAH per KVA of UPS rating per Hour

backup time) on full load (Battery shall be VRLA,

SMF in ABS Container) and Static Bypass switch

along with provision for manual bypass, suitable

isolation transformer for additional protection against

neutral faults etc. The UPS systems shall be

Microprocessor based Digital Control, using

Insulated Gate Bipolar Transistor (IGBT)'s both for

the rectifier & inverter with PWM (Pulse Width

Modulation) Technology. The quality of design,

manufacturing and inspection process should

confirm to the relevant Inter-national standards such

as IEC/EN/VDE. The operating efficiency of the

UPS systems shall be >95% at 100% non-linear

loads. Current total harmonic distortion(ITHD)/ total

demand distortion (TDD) on the input grid shall be

< 5% at 100 %load. (The required LC filters shall be

included in UPS cost), extreme power factor kit to be

include to limit the input pf to 0.99 and output power

factor shall be unity (i.e. kw rating of the UPS shall

be kva rating x 1 ) however UPS shall be suitable to

take load at 0.7 laging to 0.7 leading power factor

loads. UPS shall be suitable for incoming supply

AC single phase 160-270V 50 Hz and delivering

output AC supply true sine wave single phase

Digitally signed by A

220/230/240 Volt, 50 Hz +/- 0.2Hz, Overload

capacity of 120% for 10 mins and 150% for 1

minute. Operating temperature 0 to 40 0C, Relative

humidity 0-95% non condensing, noise level less

than 60db at 1 meter distance, Protection for Under

voltage, over voltage, abnormal output voltage,

battery over charging, output over current, short

circuit, battery deep discharge , 10 KV surge.

Display for watt/VA,Amp and Voltage power

parameters etc. UPS shall comply with low voltage

electromagnetic compatibility (EMC) achieved as

per EN 6204, EN6204 Part I and Part 2, it shall be a

Voltage and Frequency Independent (VFI) type UPS

(as per standard IEC 62040-1, 2 & 3) . The UPS

should be with IGBT Based Inverter Technology,

Communication RS232/ RS485/ SNMP port open

protocol for BMS integration as per approved by

Engineering in charge. Required battery racks, DC

breaker of suitable rating and interconnecting

copper conductor cable of suitable size and

connectors and all required accessories are

inclusive in the cost. The UPS should have QR

code which should contain drawing, test report OEM

manual, Geo- Tag of manufacturing location etc

Total of Sub Head Internal Wiring ₹ 210,418.20 ₹ 66,029.40

Digitally signed by A

Summary of Internal & External Plumbing

S. No. Description

Amount (in Rs.)

1 Internal & External Plumbing ₹ 3,556,150.75 ₹ 1,724,899.01

Modified Estimated Cost after using Correction factor on

DSR 2023 on account of GST @0.973 (Ref. CPWD Office

Memorandum File No. 158/SE (TAS)/GST/2024/O2-E

GRAND TOTAL (DSR +NSR) ₹ 5,185,033.69

GRAND TOTAL (DSR +NSR) ₹ 5,185,033.69

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Providing and fixing white vitreous china pedestal type

water closet (European type W.C. pan) with seat and lid, 10

litre low level white P.V.C. flushing cistern, including flush

pipe, with manually controlled device (handle lever),

conforming to IS : 7231, with all fittings and fixtures

complete, including cutting and making good the walls and

floors wherever

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 4 ₹ 6,515.55 ₹ 26,062.20

Providing and fixing wash basin with C.I. brackets, 15 mm

dia CP Brass single hole basin mixer of approved quality

and make, including painting of fittings and brackets,

cutting and making good the walls wherever required:-

a) White Vitreous China Wash basin size 630x450 mm

with a 15 mm CP Brass single hole basin mixer

Providing and fixing kitchen sink with C.I. brackets, C.P.

brass chain with rubber plug, 40 mm C.P. brass waste

17.9 complete, including painting the fittings and brackets,

cutting and making good the walls wherever required:

White glazed fire clay kitchen sink of size 600x450x 250

Supply, Receiving, Storing & Fixing of CP brass wall

mounted sink mixer with C.P. wall flange, swinging spout

complete as required with flow rate of 6.0 LPM complying

to Green Building requirements.

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible

tube upto 1 metre long with S.S. triangular plate to

17.16A Eureopean type W.C. of quality and make as approved by Each 4 ₹ 349.15 ₹ 1,396.60

Engineer - in - charge.

Providing and fixing CP Brass 32mm size bottle trap of

17.22A approved quality & make and as per the direction of Each 4 ₹ 1,034.80 ₹ 4,139.20

engineer in charge.

Providing and fixing C.P. brass long nose bib cock of

18.50 approved quality conforming to IS standards and weighing

not less than 810 gms

Supply, Receiving, Storing & Fixing of C.P. brass twin coat

MR-2 hook with PVC rawl plug & C.P. brass screw complete as Each 4 ₹ 724.00 ₹ 2,896.00

required. and fixing C.P. brass angle valve for basin mixer

and geyser points of approved quality conforming to

Providing and fixing unplasticised P.V.C. connection pipe

with PTMT Nuts, collar and bush of approved quality and

18.74.2 15 mm nominal bore with 45 cm length Each 8 ₹ 121.90 ₹ 975.20

Providing and fixing Chromium Plated towel ring

Rectangular shape with concealed fittings arrangement of

MR-3 approved quality and colour, of approved brand & Each 4 ₹ 1,577.00 ₹ 6,308.00

manufacture complete as per direction of Engineer in

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Providing and fixing Cp bras liquid soap container 109

mm wide, 125 mm high and 112 mm distance from wall of

MR-4 standard shape with bracket of the same materials with Each 4 ₹ 1,720.00 ₹ 6,880.00

snap fittings of approved quality and colour, weighing not

less than 105 gms.

Providing and fixing white vitreous china flat back or wall

corner type lipped front urinal basin of 430x260x350 mm

or 340x410x265 mm sizes respectively.

Providing and fixing 75 mm high, 50 mm deep and 18 mm

thick stone slab table rubbed, edges rounded and polished,

fixed in urinal partitions by cutting a chase of appropriate

width with chase cutter and embedding the stone in the

chase with epoxy grout or with cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 6 mm

nominal size) as per direction of Engineer-in-charge and

finished smooth.

8.10.2 Granite Stone of approved shade Sqm 3 ₹ 4,051.85 ₹ 12,155.55

Providing and fixing 600x450 mm beveled edge mirror of

superior glass (of approved quality) complete with 6 mm

thick hard board ground fixed to wooden cleats with C.P.

brass screws and washers complete.

Providing and fixing P.V.C. waste pipe for sink or wash

basin including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

Providing and fixing C.P. brass long body bib cock of

18.51 approved quality conforming to IS standards and weighing

not less than 690 gms.

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Providing and fixing low flow type two way bib tap as per

MR-5 approved make complete in all respect as per engineer in Each 8 ₹ 2,392.00 ₹ 19,136.00

Providing and Fixing Electric Hot Water Geyser of Stainless

Steel Material Grade 316 with Inlet and Outlet Connection

with 15 mm dia Angle Valve and Geyser (25 LTR)shall be

equipped with inbuilt non return valve and insulation on

inner and outer surfaces for prevention of heat losses 2 nos

CP round wall flange and CP Brass Screws and Rawl plugs

all other required accessories Complete in all respect as per

direction of Engineer - in - charge .

Electric Geyser 25 Litre Capacity Each 1 ₹ 11,659.00 ₹ 11,659.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the

same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good

18.8.1 15mm nominal bore Metre 40 ₹ 497.80 ₹ 19,912.00

18.8.2 20mm nominal bore Metre 30 ₹ 537.60 ₹ 16,128.00

18.8.3 25mm nominal bore Metre 20 ₹ 627.25 ₹ 12,545.00

Providing and fixing ball valve (brass) of approved quality,

High or low pressure, with plastic floats complete :

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

18.18.2 20 mm nominal bore Each 1 ₹ 462.50 ₹ 462.50

18.18.3 25 mm nominal bore Each 2 ₹ 464.05 ₹ 928.10

Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, IS : 12701 marked, with

18.48 cover and suitable locking arrangement and making Each 2000 ₹ 11.00 ₹ 22,000.00

necessary holes for inlet, outlet and overflow pipes but

without fittings and the base support for tank.

Supplying, Installation, Testing and Commissioning of uPVC

pipes type -B conforming to IS 13592 (1992) for soil,

waste and vent pipes including all fittings rubber ring type

(plain or with access door) e.g. bends, junctions, cowls,

offsets, access pieces, jointing with rubber ring joints with

lubricant etc. fixed with clamps to walls with cement

concrete 1:2:4 blocks complete in all respects. (For Soil &

Providing, laying, Jointing, Testing and commissioning of

uPVC pressure pipes of 6Kg/Sqcm pressure rating class 5

(IS : 4985-2000) including fittings, tees, bends, clamps,

coupling and adaptors supports, and jointing with solvent

joint, testing and necessary earth work in excavation,

backfilling, disposal of surplus earth with a lead upto 50m

complete, compaction and consolidation Including laying

cement concrete 1:2:4 alround UPVC pipe including bed

concrete and thrust blocks at bends as per standard design

(For Soil & Waste Pipe)

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Supplying, Installation, Testing and Commissioning of

uPVC, P or S trap of self cleansing design with / without

MR-9 vent. arm Setting in cement concrete 1:2:4 mix complete

including cost of cutting & making good the Wall / Floors

wherever required.

Providing and fixing floor drain with jali size 110X50 size

MR-10 inlet and outlet including cutting and making good the walls

and floors wherever required complete in all respects.

Providing and fixing 125 mm dia, 3 mm thick Stainless

steel grating with frame for floor traps or drains of

required pattern including cutting and making good the

floors complete.

Providing and fixing cast brass Cleanout plug with suitable

insert keys for opening in brass cap, male threaded

joint/reducer with G.I. socket caulked to Pipe/fittings of CI

pipe including cost of lead joints etc. complete in all respect.

Providing and fixing on wall face unplasticised Rigid PVC

rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10

mm gap for thermal expansion, (i) Single socketed pipes.

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Providing and fixing to the inlet mouth of rain water pipe

12.44 cast iron grating 15 cm diameter and weighing not less than Each 2 ₹ 54.70 ₹ 109.40

Supplying and laying of following size DWC SN8 pipe ISI

marked along with all accessories like socket, bend,

couplers etc. conforming to IS 16098, Part II complete with

MR-13 fitting and cutting,jointing etc.direct in ground (75 cm

below ground level) including excavation and refilling the

trench but excluding sand cushioning and protective

covering etc., complete as required.

Constructing brick masonry manhole in cement mortar

1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with

1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded

stone aggregate 20mm nominal size), foundation concrete

1:4:8 mix (1 cement : 4coarse sand (zone-III) : 8 graded

stone aggregate 40 mm nominalsize), inside plastering 12

mm thick with cement mortar 1:3 (1 cement: 3 coarse

sand) finished with floating coat of neat cement andmaking

channels in cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal size)

finished with a floating coat of neat cement complete as per

standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover

with frame (light duty) 455x610 mm internal dimensions,

total weight of cover and frame to be not less than 38 kg

(weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

19.8 Extra for depth for manholes :

19.8.1 Size 90x80 cm

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Providing and fixing square-mouth S.W. gully trap class SP-

1 complete with C.I. grating brick masonry chamber with

19.4 water tight C.I. cover with frame of 300 x300 mm size

(inside) the weight of cover to be not less than 4.50 kg and

frame to be not less than 2.70 kg as per standard design :

19.4.2 150 x 100mm size P-type

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Constructing brick masonry road gully chamber

50x45x60cm with bricks in cement mortar 1:4 (1 cement :

19.27 4 coarse sand) including 500x450mm precast RCC

horizontal grating with frame complete as per standard

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Providing orange colour safety foot rest of minimum 6 mm

thick plastic encapsulated as per IS : 10910 on 12mm dia

steel bar conforming to IS : 1786 having minimum cross

section as 23 mmx25mm and over all minimum length 263

mm and width as 165mm with minimum 112 mm space

between protruded legs having 2 mm tread on top surface

by ribbing or chequering besides necessary and adequate

19.16 anchoring projections on tail length on 138 mm as per Each 100 ₹ 553.70 ₹ 3,322.20

standard drawing and suitable to with stand the bend test

and chemical resistance test as per specifications and

having manufacture's permanent identification mark to be

visible even after fixing, including fixing in manholes with

30x20x15 cm cement concrete block 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal

size) complete as per design.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply

including all CPVC plain & brass threaded fittings This

includes jointing of pipes & fittings with one step CPVC

solvent cement, trenching, refilling & testing of joints

complete as per direction of Engineer in Charge.

18.9.4 32 mm nominal dia Pipe Metre 50 ₹ 438.60 ₹ 21,930.00

Providing and laying non-pressure NP2 class (light duty)

R.C.C. pipes with collars jointed with stiff mixture of

cement mortar in the proportion of 1:2 (1 cement : 2 fine

sand) including testing of joints etc. complete :

Digitally signed by ARTI

DSR Rate DSR Amount (in MR Rate MR Amount

2023/M Description Unit QUANTIT

Providing and laying cement concrete 1:5:10 (1 cement : 5

coarse sand : 10 graded stone aggregate 40 mm nominal

size) all-round RCC/DWC pipes including bed concrete as

per standard design :

Derrived 300 mm dia. DWC & RCC Pipe Metre 595 ₹ 1,918.80 ₹ 1,141,684.81

Derrived 450 mm dia. DWC & RCC Pipe Metre 200 ₹ 2,467.03 ₹ 493,405.20

Providing and fixing G.I. pipes complete with G.I. fittings

including trenching and refilling etc.

65 mm dia nominal bore

TOTAL CARRIED TO SUMMARY ₹ 3,556,150.75 ₹ 1,724,899.01

Digitally signed by ARTI

90 KLD STP including 10 KLD ETP

SEWAGE TREATMENT PLANT (90 KLD including 10 KLD ETP) Quantity Unit Rate TOTAL

Designing, Preparation of Shop Drawings, Supplying, Erection, Testing, Commissioning, succesfull handing

over, including all chemical / consumables for operation and maintenance of all Mechanical, Electrical,

and other components, for Sewage Treatment Plant of capacity as specified above based on MBBR

NS-1 technology complete in all respects on a Turnkey Basis, as per Tender Document comprising Technical

Conditions, Technical Specifications, Data, Drawings and any other documents attached with this Tender.

(Any item not specifically mentioned in these sections (BOQ & Specification) but required for the

successful completion including handing over.).

Nature of effluent - Sewage from toilets, bathroom / canteen & Treated water of ETP shall be discharged

into the STP. Design to take consideration of same.

The STP shall be designed based on the following parameters:

Daily average flow - 90 Cum / Day

Inlet Sewage Characteristic

BOD - Less than 250 Mg/L

S. Solids - Less than or equal to 250 Mg/L

COD - Less than or equal to 400 Mg/L

Oil & Grease - Less than 5 Mg/L

Sewage discharge standard after treatment

BOD - Less than 5 Mg/L

S. Solids - Less than or equal to 5 Mg/L

COD - Less than or equal to 10 Mg/L

Oil & Grease - Almost Nil

A) ELECTROMECHANICAL EQUIPMENTS

Bar Screens: Providing and fixing manually cleaned Bar Screens, to remove coarse and fine material in the

water made up of FRP complete as required and as specified, consisting of coarse screen & fine screen. 2 Nos ₹ 11,827.00 ₹ 23,654.00

Stainless Steel 304 Grade

Imhoff Tank Sewage Pumps: The pump sets shall be supplied with required accessories, valves, fittings,

cables etc. & as

Submersible per specification.

Discharge Pump (2 Nos -1 Working -1 Stand By)- Imoff To Equlization

Flow Rate(each) - 10 Kl/Hr

Digitally signed by ARTI

Pump 03 Phase 03 Hp 40 mm Solid Handaling Cutter Pump

Submersible Discharge Pump (2 Nos -1 Working -1 Stand By) Equlization To Anoxic

Flow Rate(each) - 10 Kl/Hr

Pumps 03 Phase 03 Hp 40 mm Solid Handaling

Suitable capacity 1 Nos ₹ 42,181.00 ₹ 42,181.00

Submersible Discharge Pump (2 Nos -1 Working -1 Stand By)

Flow Rate(each) - 10 Kl/Hr

03 Phase 03 Hp 40 mm Solid Handaling

Air Blower: Air Blowers of twin-lobe type (air cooled) for continuous service with construction in cast

iron casing, supply complete with testing and commissioning etc.as specified and as required.

(3 Nos 2 Working -1 Stand By) 3 Nos ₹ 118,268.00 ₹ 354,804.00

Ultra Filteration System

Membranes, Skid, Dosing system, all instruments including

Flow Rate(each) -5 Kl/Hr

Pumps (1 w + 1s)

Sludge Loading/Disposal Pump: Screw Type Sludge loading / Disposal pump, complete in all respects and

as per specifications. (Sludge Holding Tank To Filter press) 2 Nos ₹ 35,691.00 ₹ 71,382.00

(2 Nos -1 Working -1 Stand By) 2 m3/Hr

Filter Feed Pumps: Horizontal multistage centrifugal clear water pump set of approved make,

complete in all respects and as per specifications. 2 Nos ₹ 35,481.00 ₹ 70,962.00

Capacity : 5 KL/Hr

Head : 12 Mtr Digitally signed by ARTI

(2 Nos -1 Working -1 Stand By)

Dual Media Filter: Providing and fixing vertical Dual Media Pressure Filter with suitable foundation boits

& other accessories, mounting frame, complete with testing and commissioning etc.as required & as 1 Set ₹ 153,749.00 ₹ 153,749.00

Mulitgrade Pressure Sand Filter/ Vessel

Dia : 600 mm x 1800 mm height

Filtration velocity : 5 m3/hr/m2

Filter Media : Fine and coarse sand, pebels and gravels

Valve dia : 65 mm

MOC: MSFRP Vessel Dia:900 Height:1800

Activated Carbon Filter: Providing and Fixing of Activated carbon filter as per Manufacturer's standard

and testing & commissioning complete. 1 Set ₹ 160,237.00 ₹ 160,237.00

Activated Carbon Filter/ vessel

Dia : 600 mm x 1800 mm height

Filtration velocity : 5 m3/hr/m2

Filter Media : Activated carbon, fine and coarse sand, pebels and gravels

Valve dia : 65mm

MOC: MSFRP Vessel Dia:900 Height:1800

Dosing System: Providing and fixing chemical dozing system for centrifuge of approved make with all

standard accessories & structural arrangement including suitable foundation bolts & other accessories 1 Set ₹ 23,655.00 ₹ 23,655.00

etc. complete as required and as specified.

Note: For Treated Water

Pump: Agitator 1/2 Hp Single Phase Standard Top Mount With SS Arams

Dosing Pump With 100 Ltr. HDPE/FRP Tank

Ozonation system at the clarified water tank complete as per specifications 1 Set ₹ 171,643.00 ₹ 171,643.00

Required Ozone Generator : 20 Gm/Hr

Ozone Output : 20 Gm/Hr Ozone Di-electrics : SS-316

Requirments & Utlities Power Supply : 220-230 VAC / 50 Hz / 1 PE / 1.5 KW

Oxygen Feed Flow : 05- 10 LPM @ 90%± 2%

Oxygen Feed Pressure : 0.75-1.0 kg/cm2

Feed Pressure : 1.0-1.5 Kg/cm2

Oxygen Concentrator10 LPM HG-10 * Oxygen Flow Rate : 10 LPM@ 90% ± 2%

Digitally signed by ARTI

Total Oxygen Flow : 05- 10 LPM @ 0.5-0.75 kg/cm2g SS-304 Skid Mounted

Ozone Mixing Components

Type of Pump : Recirculation Pump Flow & Pressure : 2.5 - 3.0 m3/hr

Ventury Injector + NRV

Electro Magnetic flow meter 2 Nos ₹ 35,691.00 ₹ 71,382.00

Sludge Handling Mechanism (Filter Press): Providing and fixing of sludge handling arrangement (Filter

Press) complete with testing & commissioning as required and as specified. 1 Set ₹ 158,989.00 ₹ 158,989.00

Supplying, installation, testing & commissioning of Filter Press with all required acessories for dewatering

Filter Press- 12 inch * 12 inch 11 Plates With Hydrolic System- 1 Hp

Cake Thikess: 35

Filteration: 39.40

Wet Volume Cake: 515 Ltr

UV for Supply to Flushing & Horticulture water outlet Line: Providing and installation of Online UV

system complete with testing & commissioning as required and as specified. 1 Set ₹ 181,702.00 ₹ 181,702.00

The Ultra-Voilet unit shall have with reactor, cabinet housing, cabinet cooling, treatment chamber,

electrical panel, temperature safety control, lampout alert, UV radiometer along with UV monitoring

system and UV monitoring readout panel. The UV Dosage should be > 60,000 uW – Sec / sq.cm. The lamps

should be selected based upon the flow requirement of respective unit.

Capacity : 10 KL/Hr

Sludge Trolley: Fabrication and supply of sludge trolley for transport of sludge complete as per

requirements as specified. 1 Lot ₹ 473,074.00 ₹ 473,074.00

Bio media for MBBR tank and Tubesettler complete as per specifications

MBBR Bio Filter Media (MBBR Media) 16/22- v

PVC Tube Deck Media 1000 mm

B) PIPING AND VALVES ACCESSORIES 1 Lot ₹ 236,537.00 ₹ 236,537.00

Digitally signed by ARTI

G.I. Pipe: Provding and fixing heavy duty G.I. pipe confiming to IS. 1239 upto 150 mm and IS 3589 for dia

200 mm and above complete as required & as per specifications.

uPVC Threaded Water Pipes: Providing and fixing uPVC threaded water pipes (I.S:4985-2000) Class - 5

(Min. 10 Kg/cm2) complete as required & as per specifications.

MS (C Class) - For all exposed air piping and flexible braded pipe for submerged air piping.

Butterfly Valves: Providing & fixing butterfly valve of rating PN 1.6, wafer type, in cast iron body with

Ductile Iron disc, EPDM seal, SS single piece shaft, conforming to IS-13095, complete as required and as

Ball Valves: Providing and fixing forged brass ball valve having stainless steel / brass ball tested to 20

kg/cm2 complete as required and as specified.

Puddle flanges: Providing & fixing GI hot dipped puddle flanges for the tank complete as per the

Non-Return Valves: Providing & fixing non return valve Dual Plate type, conforming to API-594 or IS 3512,

complete as required and as specified.

C) CONSUMABLES FOR OPERATION AND MAINTENANCE 1 Lot ₹ 42,181.00 ₹ 42,181.00

Supply & Consumption of Consumables, solutions, chemicals, etc. for STP operation and maintenance upto

successful commissioning & handing over of STP.

D) ELECTRICAL SYSTEM (COMMON PANEL FOR STP & ETP) 1 Lot ₹ 289,913.00 ₹ 289,913.00

STP Panel: Design, manufacture, supply, installation, testing and commissioning of the STP panel

complete as required and as specified.

Aluminium Conductor: Supply of sizes of 1.1KV grade XLPE insulated and PVC sheathed aluminium

conductor armoured stranded power cables conforming to IS 7098 Part-1 as ammended upto date and as

Supplying and making of cable end termination with brass single compression gland and Al. lug for PVC

insulated and sheathed armoured cables of 1.1 K.V. aluminum conductor as required.

Laying and fixing of one number XLPE /PVC insulated and PVC sheathed power of 1.1 KV grade of

following sizes on surface or existing cable tray complete as required.

Earthing: Earthing with GI earth plate of 600mm x 600mm x 6mm thick, including accessories and

providing masonary enclosure including MS cover plate having locking arrangement and watering pipe

etc. with charcoal and salt complete as required & as specified.

Digitally signed by ARTI

G.I. Strip: Providing and Fixing 25 mm x 5 mm G.I. Strip in 40 mm dia. G.I. pipe from earth electrode

complete as required.

G.I. Strip on Surface: Providing and Fixing 25 mm x 5 mm G.I. Strip on surface or in recess for earth

connection as per specifications complete as required.

G.I. Wire: Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Cable Tray: Fabrication and installation of perforated MS cable tray including horizontal and vertical

bends, reducers, tees, cross-members and other accessories as required duly suspended from the ceiling

with MS Suspenders and including painting with black synthetic paint as required.

Rubber Mat: Providing electric insulated rubber mat non-skid type with grooved top 90 cm wide & 12 mm

thick as per IS : 5424 as required suitable for 1100 volts.

1) Bypass arrangement shall be provided such that equalization tank pump can be used to pump

out sewage to external manhole incase of maintenance of ETP.

NS-2 EFFLUENT TREATMENT PLANT (10 KLD ETP)

The ETP shall be designed as water retaining structures, with necessary chemical dosing as required

by the manufacturer's design. All the equipment, piping, and pumps to be housed in the ETP , inlet, outlet,

overflow, vent, etc. The Plant shall be complete with a central Electrical Power and Control panel fully

pre/site wired and with all power and control cables to all pumps and equipment including all

instrumentation, level and other controls. Note: Treated effluent will be mixed in Filter Feed Tank/CCT of

Effluent from labs etc. Some solvent/ chemical waste originating typically from College complex shall

also be discharged into the ETP. Design to take consideration of same.

Daily average flow - 10 Cum / Day

S. Solids : 400 - 650 Mg/l

Oil & Grease : 50-140 mg/L

Effluent discharge standard after chemical treatment before mixing to CCT :-

S. Solids : Less than 100 mg/l

COD : Less than 100 mg/l

Digitally signed by ARTI

Oil & Grease : Less than 5 mg/l

BOD : Less than 30 Mg/L

SS Perforated Bar Screen 2 Nos ₹ 14,257.00 ₹ 28,514.00

The ETP shall consist of following units but not limited to these unit as may be required by the

manufacturer's design. MS PVC coated rungs in all tanks & Platform for maintenance etc. complete as

SS Perforated screen having provision for chain lifting arrangement etc. complete as required ( 1 SET)

Imhoff Tank cum Equalization tank including provision for aeration will be kept to avoid any smell

Capacity : 1.0 M3/hr @ Discharge Head 10 M head (1 Working + 1 Standby) Submersible Cutter Discharge

Equalization tank To further with air diffuser and piping complete of adequate capacity. 2 Nos ₹ 27,531.00 ₹ 55,062.00

Capacity : 1.0 M3/hr @ Discharge Head 10 M head (1 Working + 1 Standby) Submersible Discharge pump

Clear Water Tank to Filter Feed Pump 2 Nos ₹ 27,531.00 ₹ 55,062.00

Capacity : 1.0 M3/hr @ Discharge Head 10 M head (1 Working + 1 Standby) Monoblock Discharge pump

Providing and fixing all piping (as described below) and isolation control valves, non return valves etc. for 1 Nos ₹ 98,323.00 ₹ 98,323.00

making the system complete

PVC piping (10kg/sqcm) - For all submerged waste water piping

MS (C Class) - For all exposed air piping and flexible braded pipe for submerged air piping.

GI (C class) for all other water piping.

Providing and fixing all instrumentation eg. Pressure guages, level controllers, sensors, rotametres for air, 1 Nos ₹ 98,323.00 ₹ 98,323.00

water etc. for making the system complete

Reaction tank with air diffuser and piping complete of adequate capacity. Fine air bubble jet diffuser

with EPDM seat minimum number of diffusers to be provided as per manufacturer's recommendations in 1 Nos ₹ 58,993.00 ₹ 58,993.00

RCC Construction.

Secondary clarifier tank, Tube Deck Media, hopper bottom type with arrangement of deep well, baffle

wall, scum removal arrangement, outlet launders with arrangement of lifting sludge from the bottom etc. 1 Nos ₹ 73,744.00 ₹ 73,744.00

complete as required in RCC Construction.(1 SET)

Digitally signed by ARTI

EQUALIZED WASTE WATER TRANSFER PUMPS : Sludge Transfer Pumps To Sludge Holding Tank

Providing & fixing Horizontal centrifugal Self-Priming pumps solid handling (min. 7 mm) pumps. The

pumps shall be made of CI casing, CI Impellar, SS shaft & sleeve, Mechanical Seal are connected to a TEFC

induction motor mounted on a common channel base frame with coupling guard, 150 mm dia pressure

gauge with GM isolation cock, suitable vibration eliminator pads of approved design. Motor to be suitable

for 400/440 V, 3 Phase, 50 cycles AC power supply, including all necessary piping, valves and other

accessories and concrete foundation complete as required.

Capacity : 3.0 M3/hr @ Discharge Head 10 M head (1 Working + 1 Standby)

Mono block centrifugal Sludge Transfer Pumps (2 Nos. - One working & one standby ( 1 SET)

(Solid handling cap. 6 mm)

Flow rate (each) = 1 m3 / hr or as required

Head = 8-10 Mtr or as required

Providing and fixing Lime/Alum/Polyelectrolyte dosing system consisting of ABS lime dosing pump

(0-6 lph) with 100 ltr HDPE tanks including all piping from the dozer to the reaction tank etc. complete in 3 Nos ₹ 93,408.00 ₹ 280,224.00

1) Bypass arrangement shall be provided such that equalization tank pump can be used to pump out

sewage to external manhole incase of maintenance of ETP.

(90 KLD including 10 KLD ETP) ₹ 4,987,105.00

Digitally signed by ARTI

190 KLD STP including 10 KLD ETP

SEWAGE TREATMENT PLANT (190 KLD including 10 KLD ETP) Quantity Unit Rate TOTAL

Designing, Preparation of Shop Drawings, Supplying, Erection, Testing, Commissioning, succesfull handing

over, including all chemical / consumables for operation and maintenance of all Mechanical, Electrical,

and other components, for Sewage Treatment Plant of capacity as specified above based on MBBR

NS-1 technology complete in all respects on a Turnkey Basis, as per Tender Document comprising Technical

Conditions, Technical Specifications, Data, Drawings and any other documents attached with this Tender.

(Any item not specifically mentioned in these sections (BOQ & Specification) but required for the

successful completion including handing over.).

Nature of effluent - Sewage from toilets, bathroom / canteen & Treated water of ETP shall be discharged

into the STP. Design to take consideration of same.

The STP shall be designed based on the following parameters:

Daily average flow - 190 Cum / Day

Inlet Sewage Characteristic

BOD - Less than 250 Mg/L

S. Solids - Less than or equal to 250 Mg/L

COD - Less than or equal to 400 Mg/L

Oil & Grease - Less than 5 Mg/L

Sewage discharge standard after treatment

BOD - Less than 5 Mg/L

S. Solids - Less than or equal to 5 Mg/L

COD - Less than or equal to 10 Mg/L

Oil & Grease - Almost Nil

A) ELECTROMECHANICAL EQUIPMENTS

Bar Screens: Providing and fixing manually cleaned Bar Screens, to remove coarse and fine material in the

water made up of FRP complete as required and as specified, consisting of coarse screen & fine screen. 2 Nos ₹ 23,655.00 ₹ 47,310.00

Stainless Steel 304 Grade

Imhoff Tank Sewage Pumps: The pump sets shall be supplied with required accessories, valves, fittings,

cables etc. & as

Submersible per specification.

Discharge Pump (2 Nos -1 Working -1 Stand By)- Imoff To Equlization

Flow Rate(each) - 19 Kl/Hr

Digitally signed by ARTI

Pump 03 Phase 03 Hp 40 mm Solid Handaling Cutter Pump

Submersible Discharge Pump (2 Nos -1 Working -1 Stand By) Equlization To Anoxic

Flow Rate(each) - 9.5 Kl/Hr

Pumps 03 Phase 03 Hp 40 mm Solid Handaling

Suitable capacity 1 Nos ₹ 84,361.00 ₹ 84,361.00

Submersible Discharge Pump (2 Nos -1 Working -1 Stand By)

Flow Rate(each) - 19 Kl/Hr

03 Phase 03 Hp 40 mm Solid Handaling

Air Blower: Air Blowers of twin-lobe type (air cooled) for continuous service with construction in cast

iron casing, supply complete with testing and commissioning etc.as specified and as required.

(3 Nos 2 Working -1 Stand By) 3 Nos ₹ 236,537.00 ₹ 709,611.00

Ultra Filteration System

Membranes, Skid, Dosing system, all instruments including

Flow Rate(each) -9.5 Kl/Hr

Pumps (1 w + 1s)

Sludge Loading/Disposal Pump: Screw Type Sludge loading / Disposal pump, complete in all respects and

as per specifications. (Sludge Holding Tank To Filter press) 2 Nos ₹ 71,383.00 ₹ 142,766.00

(2 Nos -1 Working -1 Stand By) 2 m3/Hr

Filter Feed Pumps: Horizontal multistage centrifugal clear water pump set of approved make,

complete in all respects and as per specifications. 2 Nos ₹ 70,961.00 ₹ 141,922.00

Capacity : 10 KL/Hr

Head : 12 Mtr Digitally signed by ARTI

(2 Nos -1 Working -1 Stand By)

Dual Media Filter: Providing and fixing vertical Dual Media Pressure Filter with suitable foundation boits

& other accessories, mounting frame, complete with testing and commissioning etc.as required & as 1 Set ₹ 307,498.00 ₹ 307,498.00

Mulitgrade Pressure Sand Filter/ Vessel

Dia : 1000 mm x 1800 mm height

Filtration velocity : 10 m3/hr/m2

Filter Media : Fine and coarse sand, pebels and gravels

Valve dia : 65 mm

MOC: MSFRP Vessel Dia:900 Height:1800

Activated Carbon Filter: Providing and Fixing of Activated carbon filter as per Manufacturer's standard

and testing & commissioning complete. 1 Set ₹ 320,478.00 ₹ 320,478.00

Activated Carbon Filter/ vessel

Dia : 1000 mm x 1800 mm height

Filtration velocity : 20 m3/hr/m2

Filter Media : Activated carbon, fine and coarse sand, pebels and gravels

Valve dia : 65mm

MOC: MSFRP Vessel Dia:900 Height:1800

Dosing System: Providing and fixing chemical dozing system for centrifuge of approved make with all

standard accessories & structural arrangement including suitable foundation bolts & other accessories 1 Set ₹ 47,307.00 ₹ 47,307.00

etc. complete as required and as specified.

Note: For Treated Water

Pump: Agitator 1/2 Hp Single Phase Standard Top Mount With SS Arams

Dosing Pump With 100 Ltr. HDPE/FRP Tank

Ozonation system at the clarified water tank complete as per specifications 1 Set ₹ 343,287.00 ₹ 343,287.00

Required Ozone Generator : 30 Gm/Hr

Ozone Output : 30 Gm/Hr Ozone Di-electrics : SS-316

Requirments & Utlities Power Supply : 220-230 VAC / 50 Hz / 1 PE / 1.5 KW

Oxygen Feed Flow : 05- 10 LPM @ 90%± 2%

Oxygen Feed Pressure : 0.75-1.0 kg/cm2

Feed Pressure : 1.0-1.5 Kg/cm2

Oxygen Concentrator10 LPM HG-10 * Oxygen Flow Rate : 10 LPM@ 90% ± 2%

Digitally signed by ARTI

Total Oxygen Flow : 05- 10 LPM @ 0.5-0.75 kg/cm2g SS-304 Skid Mounted

Ozone Mixing Components

Type of Pump : Recirculation Pump Flow & Pressure : 2.5 - 3.0 m3/hr

Ventury Injector + NRV

Electro Magnetic flow meter 2 Nos ₹ 71,383.00 ₹ 142,766.00

Sludge Handling Mechanism (Filter Press): Providing and fixing of sludge handling arrangement (Filter

Press) complete with testing & commissioning as required and as specified. 1 Set ₹ 317,978.00 ₹ 317,978.00

Supplying, installation, testing & commissioning of Filter Press with all required acessories for dewatering

Filter Press- 18 inch * 18 inch 17 Plates With Hydrolic System- 1 Hp

Cake Thikess: 35

Filteration: 39.40

Wet Volume Cake: 515 Ltr

UV for Supply to Flushing & Horticulture water outlet Line: Providing and installation of Online UV

system complete with testing & commissioning as required and as specified. 1 Set ₹ 363,404.00 ₹ 363,404.00

The Ultra-Voilet unit shall have with reactor, cabinet housing, cabinet cooling, treatment chamber,

electrical panel, temperature safety control, lampout alert, UV radiometer along with UV monitoring

system and UV monitoring readout panel. The UV Dosage should be > 60,000 uW – Sec / sq.cm. The lamps

should be selected based upon the flow requirement of respective unit.

Capacity : 10 KL/Hr

Sludge Trolley: Fabrication and supply of sludge trolley for transport of sludge complete as per

requirements as specified. 1 Lot ₹ 946,148.00 ₹ 946,148.00

Bio media for MBBR tank and Tubesettler complete as per specifications

MBBR Bio Filter Media (MBBR Media) 16/22- v

PVC Tube Deck Media 1000 mm

B) PIPING AND VALVES ACCESSORIES 1 Lot ₹ 473,073.00 ₹ 473,073.00

Digitally signed by ARTI

G.I. Pipe: Provding and fixing heavy duty G.I. pipe confiming to IS. 1239 upto 150 mm and IS 3589 for dia

200 mm and above complete as required & as per specifications.

uPVC Threaded Water Pipes: Providing and fixing uPVC threaded water pipes (I.S:4985-2000) Class - 5

(Min. 10 Kg/cm2) complete as required & as per specifications.

MS (C Class) - For all exposed air piping and flexible braded pipe for submerged air piping.

Butterfly Valves: Providing & fixing butterfly valve of rating PN 1.6, wafer type, in cast iron body with

Ductile Iron disc, EPDM seal, SS single piece shaft, conforming to IS-13095, complete as required and as

Ball Valves: Providing and fixing forged brass ball valve having stainless steel / brass ball tested to 20

kg/cm2 complete as required and as specified.

Puddle flanges: Providing & fixing GI hot dipped puddle flanges for the tank complete as per the

Non-Return Valves: Providing & fixing non return valve Dual Plate type, conforming to API-594 or IS 3512,

complete as required and as specified.

C) CONSUMABLES FOR OPERATION AND MAINTENANCE 1 Lot ₹ 84,361.00 ₹ 84,361.00

Supply & Consumption of Consumables, solutions, chemicals, etc. for STP operation and maintenance upto

successful commissioning & handing over of STP.

D) ELECTRICAL SYSTEM (COMMON PANEL FOR STP & ETP) 1 Lot ₹ 579,822.00 ₹ 579,822.00

STP Panel: Design, manufacture, supply, installation, testing and commissioning of the STP panel

complete as required and as specified.

Aluminium Conductor: Supply of sizes of 1.1KV grade XLPE insulated and PVC sheathed aluminium

conductor armoured stranded power cables conforming to IS 7098 Part-1 as ammended upto date and as

Supplying and making of cable end termination with brass single compression gland and Al. lug for PVC

insulated and sheathed armoured cables of 1.1 K.V. aluminum conductor as required.

Laying and fixing of one number XLPE /PVC insulated and PVC sheathed power of 1.1 KV grade of