SPECIAL REPAIR TO GOVT ACCN AT SHIVAJI ENCLAVE BLOCK NO P-800 OF ORDNANCE DEPOT TALEGAON

Amount

Taking out existing water proofing treatment including cement plaster(any no of layers) on roof surfaces, cleaning the surfaces and removing the debris outside MOD land complete all as specified and as directed.

Extra over rendering for work in isolated width such as in bands, sunk pannels, cornices, skirting sides of slabs, parapet sides and top drip moulds etc and similar work not exc 15 cm width or girth complete all as specified and directed.

M&L for cleaning the plastered / concrete surfaces with wire brushes and applying water proofing treatment as under :- (a) Provide 10 mm thick plaster in CM (1:6) (b) Apply one coat of oil bituminous primer @ 0.20 kg/Sqm over concrete surface. (c) Laying APP Polimerised modfied membrane not less than 3 mm thick and weighing not less than 3.5 kg per Sqm by torch applicaton method. (d) The overlap for APP membrane shall be 75 mm on longitudinal direction and 100 mm on transverse direction (e) Finally applying a coat of solar reflective bitumiious aluminium paint @ 0.15 Kg/Sqm over the membrane. (f) The make / treatment shall be from the one of the following manufacturer:- (i) 'Moply FP' of M/s Texsa (I) Pvt Ltd. (ii) 'Hyperplast' pf IWL India Ltd. (iii) 'Super thermpay' manufactured by M/s Shalimar tar product (iv) 'Hydroflame' of M/s Hydrotech Ltd.

Taking out existing PVC water tanks of capacity 500 litres, setting aside (or lowering if required) for replacement complete all as specified and as directed.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe spouts for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing of 15 mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing of 20 mm bore of pipe complete all as specified and as directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

M & L for 15 mm bore GI pipe medium grade with all fittings and fixtures and fixed to wall, ceiling, floor complete all as specified and as directed.

M & L for 20 mm bore GI pipe medium grade with all fittings and fixtures and fixed to wall, ceiling, floor complete all as specified and as directed.

Supply and laying including jointing, Tubes galvanised, (Medium grad), with all GI fittings( Tee, elbow, socket bed reducer) clamps screws MS clamps, hooks complete on laying of ground/fixed on wall/floor/ laid in trenches of sizes 50mm bore

Supply and laying including jointing, Tubes galvanised, (Medium grad), with all GI fittings( Tee, elbow, socket bed reducer) clamps screws MS clamps, hooks complete on laying of ground/fixed on wall/floor/ laid in trenches of sizes 25mm bore

S & F in repairs ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore and fixed (minimum weight 210 gms ) complete all as specified and as directed.

S & F in repairs 15 mm dia stop/angle valves fancy type chromium plated cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union fixed in repair for 15 mm dia GI pipe all as specified and as directed.

S&F in repairs 15 mm dia bib taps long body cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass furrule and fixed for 15mm dia pipe complete all as specified and as directed.

S & F in repairs 15 mm dia Brass cromium plated shower rose of 125 mm long leg complete all as specified and as directed.

S&F in repairsGrating round 100 mm size of PTMT (Minimum weight 25gms.) complete all as specified and as directed.

S& F in repairs stainless steel Sinks 1 mm thick for kitchen or laboratory with plugs, washers and wastes; including beding in cement mortar overall size 495mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete including fixing cantilever brackets and connecting union to waste pipe and coupling complete all as specified and as directed.

S & F in repairs for PVC connection pipe 15mm dia with PTMT nuts of length 450mm complete all as specified and as directed.

S&F as in repairs PVC low level flushing cristern white 10 litre capacity incl PVC inlet pipe with brass check low level full both sides alongwith PVC flush pipe 32mm dia jointed to WC and handle incl brackets all as directed.

S&F vitreous china squatting pan ORRISA PATTERN size 580x440mm white with integral foot rests excluding flushing cistern & flush pipe fixed in repairs complete all as specified and as directed. .

Dismantling / taking down AC waste/vent pipes fixed to walls with all fittings/ accessories 100 mm dia pipes all as specified and directed by Engineer-in-Charge.

S&F, PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, or laid in trenches bore of pipe 110 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F,110 mm dia PVC (SWR) bends, any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F, 110 mm dia PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), all as speicfied and directed.

M & L non skid coloured ceramic tiles 7 to 8 mm thick area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors, etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match. Including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete.

M&L for non-skid coloured tiles 7 to 8mm thick (square/rectangular) polished area of each tile 0.36 sqm but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm th screed bed in CM 1:6 complete all as specified and as directed.

Ditto as per item above but on skirting over 10 mm th rendering in CM 1:4 complete all as specified and as directed.

M & L Glazed ceramic tiles in vertical surface 450mm x300x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles incl backing coat 10mm thick in CM 1:4 all as direced.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid and bedded and jointed in cement mortar complete all as specified and as directed.

M&L for Marble work green marble 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as specified.

M&L machine cut cuddapah stone slab flooring 20-25mm thick over and including cement screed based 20 mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl cutting polishing and rubbing complete all as specified and as directed.

Demolition of cement concrete ( unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for cement concrete Type C2 1:3:6 (using 40mm graded aggregates) as in plinth protection 75 mm thick finished top surface even and smooth without using extra cement complete all as specified and as directed.

M & L for 100 mm thick Cement concrete type D-2 1:4:8 (40 mm graded aggregate) as in sub base complete all as specified and as directed.

M & L for precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment over 25 mm thick sand cushion complete all as specified and as directed.

Taking down chowkhats or with shutter (without taking off shutter from the frames) & removing from site exc. 1.5 Sqm but n. exc. 4 Sqm each.

–Ditto- as item above but n.exc. 1.50 sqm each

Taking down shutters of any description exc. 1 sqm and not exc. 2 sqm each

Taking down steel window / ventilator of any size

Cutting holes in brick walls exc half brick but n exc one brick, built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required -depth of embedded portion of holdfast or lugsmeasured from the face of jamb into the wall - exc. halfbrick but n exc. one brick.

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 125 X 60mm

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 105 X 60mm

M&L for PCC 1:2:4 type B1 in door frame filling all as specified and directed.

S&F factory made 35 mm thick plain framed paneled shutter (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with Commercial veneered on both faces the size of rail and style as per IS-1003 ( Pt-I) kiln seasoned and Chemically pressed of 2nd class hard wood.

Supply and fixing three track sliding window including frame with two shutters with 4mm thick tinted glass and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips etc; fabricated using following aluminium anodised sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engineer-in-Charge. (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352. (Note:- Cost of Tinted glass & wire cloth shall be included in the quoted rate of the item).

S&F aluminium grill with suitable aluminium anodised frame F/H section manufactured by M/s DECO GRILL as per design No DG-104, 10mm thick. complete all as specified and as directed

S & F louvered aluminium ventilators including frame with adjustable luvers with provision of fixing exhaust fan fixed with and incl 4mm thk frosted glass louvers and sall be fly proof with stainless steel wire gauge of 0.36mm dia and 1.18mm aperture fixed to frame with aluminium beading and following aluminium powder coated sections conforming of `JINDAL' or of equivalent make and rubber beading etc all as directed. (a) SP20048 (b) Glazing clipa 19352 Note : Cost of glass louvers and wire cloth shall be incl in the quoted rate of the items

S & F 25mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge.

Supply and fixing 30 mm thick Fiberglass ReinforcedPlastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick S&F FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00mm complete all as specified and directed.

S & F 150 mm size extruded aluminium alloy handles,fabricated type anodised.

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 150mm

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 100mm

S& F 100 mm But hinges, stainless steel, bright polished and fixed, type B-11 all as specified and directed

S & F aluminium alloy , anodised , sliding door bolt with hasp , staple ( bolt type ) & fixing clips of sheet, cast or extruded section & fixing bolts & sliding bolts of extruded section or cast aluminium alloy & fixed - length of bolt 250 mm

S&F in repairs floor door stopper with overall length of cover plate is 150 mm, of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.

Dismantling of boarding, any description and fixed in any position with nails complete all as specified and directed.

Dismantling timber fillets under 40 Sq.cm in section unframed work , in any position complete all as specified and directed.

S & F in repairs pre-laminated particle board 25mm thick exterior grade prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work incl 6mm thick teak wood lipping patti complete.

S & F of 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails sectional area exc 13 & not exc 25 sqcm complete all as specified and directed.

S&F in repairs continuous Piano type hinges mild steel bright finish or electrogalvanised (width of flap 40 mm when open) complete.

S & F of 100 mm size brass hasp and staple safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for rendering cement plaster 10 mm thick in CM 1:6 on fair faces of brick walls finished even and smooth w/o using extra cement complete all as specified and as directed.

M & L for Rendering 05 mm thick cement plaster on concrete surface of ceiling in cement mortor 1:3 shall be even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick work or conrete wall surfaces finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M & L for Preparation of newly plastered surfaces of wall and appling two coats of oil bound distemper on walls over a coat of alkali resistant primer on plastered surfaces complete including 3mm thick wall care putty complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coat of white washing complete all as specified and as directed.

M & L for Preparation of newly plastered surfaces of wall and appling two coats of cement base paint on walls over a coat of alkali resistant primer on plastered surfaces complete all as specified and as directed.

M&L for preparation and applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces n exc 10cm width or girth complete all as specified

M&L for complete removal of existing treatment from old decorated surfaces of wall, preperation of surface and applying two coats of distemper oil emulsion over and including a coat of alkali resistant primer complete all as specified and directed by Engineer - in - Charge.

M&L for Complete removal of existing treatment from old decorated surfaces of walls, preperation of surface and applying two coats of cement base paint over and including a coat of alkali resistant primer complete all as specified and directed by Engineer - in - Charge.

M&L applying one coat of white wash on old decorated surfaces of ceiling including preparation of surfaces complete all as specified & directed by Engineer-in-Charge.

M&L preparation of old painted wooden surfaces of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in Suken portion exe 15 cm thickness (below or aboveground level) complete all as specified and directed.

M & L cement conrete 1:7:12 type F2 (uisng 40mm graded aggregate) as in sunkun filling complete all as specified and directed.

Providing and carrying out water proofing treatment to toilet ,sunken slabs ,wet areas etc,after proper surface prepration ,carry out cementitious ingection grouting at leakage point using Cebex 100 plasticised expanding grouting admixture ,application of polymer modified at slab wall junction using Nitoband SBR latex screed modifier cum bonding agent and application ot two coats of brushbond RFX two part acrylic polymer modified cementitious elastomeric waterproof and protective coating etc,complete including 15 mm thick cement plaster in CM 1:4 all tools and plants as per manufacturer's specification paint complete all as specified and directed.

S&F in repair Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and as directed by Engineer-in-Charge

Taking down carefully copper/aluminium point wiring (light, fan, socket or ower) complete,(fittings such as switches, ceiling roses,pendants, regulators sockets etc. to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc.

Taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified

Taking down unserviceable main switches ,DBs alongwith teak wood boards etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified

M&L for Point wiring complete with 1.5 Sqmm single core PVC insulated but unsheathed copper conductor FRLSH cable 1100 V grade drawn through concealed PVC conduit of suitable size as per site requirement including tees, junctions etc fixed on wall/ floor/ ceiling etc including 1.5 Sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire complete ISI marked for suitable size excluding modular flush box, cover plate all accessories and making good the disturbed surfaces of wall all and matching the surface to the existing finishing colour all as specified & directed for the followings:-

One light/ Fan point controlled by one one way switch.

One light point controlled by one two way switch

One bell point controlled by one bell switch.

One 3 pin 5 Amps switch socket outlet on the same board with other switch controlled.

One 3pin 5 Amp switch socket independent controlled by one way switch including 1.5 Sqmm pvc inulatedand pvc unsheathed single core copper conductor cable as a earth wire to common earth connection to earth dolly

All as per item above but One 6 pin 6/16 Amp switch socket independent controlled by one way switch including 2.5 Sqmm pvc inulatedand pvc unsheathed single core copper conductor cable as a earth wire to common earth connection to earth dolly

S & F Switch modular type single pole one way 230V 6Amps

S & F Switch modular type type single pole two way 230V 6Amps

S & F Socket outlet 2 in 1 , 3 pin 5 Amps modular type 230V, multipurpose type

S & F Switch socket combination modular type multi purpose 16A, 5 in 1controlled by one switch 230V.

S & F ceiling rose surface PVC 50 mm dia three terminals including PVC mounting block, white/lvoury /Urea finish.

M&L in repair for stepped type electronic fan regulator flush type on the existin phenolic laminated sheet etc as required for ceiling fan 230 volt AC supply, 50HZ 1200/1400 mm sweep

S & F modular Bell push, flush type, 5 amp, 230V

S & F Bell ding dong type 230V

M&L submain wiring with 2 single core PVC insulated multistranded flexible copper conductor 1100Volts grade (FRLS) cables 4 Sqmm and 1 run 4 Sq mm PVC insulated multistrand copper conductor cable (FRLS) of green colour for continious earthing drawn through concealed PVC conduit of suitable size and with all accessories all as directed and specified by Engr-In-charge.( Note: Two runs of 4 sqmm, one run of 4 sqmm copper conductor and one run of concealed PVC conduit of suitable size and with all necessary fixing accessories and making good disturbed surface area shall be measured as one length.)

M & L for earthing complete with galvanised steel earth plate electrode 60cm ×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel,earth wire protected by GI pipe 15 mm dia 'light grade' including charcoal dust, common salt, excavation & earth work, PCC Pit with 1:3:6 type C-1, 40 mm thick RCC cover in 1:2:4 type B-1 reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with MS handles 12 mm dia, PGI funnel & GI watering pipe 'light grade' 20 mm bore all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

M & L MCB DB SPN sheet metal double door enclosure mounted on teak wood board of suitable size for mounting MCB 230 Volts with 200 Amps rated bus bar 8 way

S & F MCB SPN 32 amps, 240Volts 10KA

S & F MCB SP 5-40 amps, 240Volts 10KA

Supply & fixing inverter LED tube light fitting along with fixture, 20 W

Supply & fix 2 feet 09W linear aluminium LED Batten with white acrylic cover complete with all accessories prewired and connecting up twin core twisted flexible copper conductor cable with suitable size.Cat Part No : LHEXBLP7IN1W009 of Havells, SZSLBMX009 of Shakti and equavalant of Philips,Bajaj, Crampton, Havells and HPL.

Taking down ceiling fan 1200/1400 mm sweep / exhaust fans including disconnection of electric connection and removing the blades in safe for reinstalling

Supply & fix ceiling fans complete with remote and accessories 230 V,1200 mm sweep BLDC type

Supply and fix in replace indoor meter box made up of 2 mm thick MS Sheet duly powder coated with closing and locking arrangement as per suitable size (for fixing of following items with sufficient space) on wall with wooden plank of 18 mm thick inside panel alongwith following new items including all making connection, accessories (i.e. lugs, thimbles, nut, washers etc) and arrangments :- a) 4 Pole MCCB -63A - 01No (as main incomer) (Make - Havells/Legrand) b) Bus bar 200A rating - 04 Pole - 01 Set (for distribution) c) MCB DP 40A - 05 Nos (Outgoing) (Make -Havells/Legrand) d) Energy electric single phase meter - 04 Nos (Make-HPL/Bentec)

S & F LED light fitting for building security light fitting 1x 45 w, 230 V,complete with all accessories internally pre-wired and including connecting up with 2.5 sqmm twin core flexible copper cable for connection from ceiling rose to fitting including LED light and GI bracket medium grade of 1.2 meter shaped to 120 degree for fixing of fitting on wall with clamps and Make : Bajaj / philips / Crompton

S & F exhaust fan AC single phase 230 V,300 mm sweep, heavy duty with louvers, PVC body, blades, Insulation Class A including capacitor complete all as specified and directed by Engineer-in-charge( including making hole on exixting wall and making good surface of wall with necessary PCC Work and plaster etc.) . Make :-Model : Ventil Air-DB 300 mm of Havells and equavalant of GEC/Bajaj/ CG/ Khaitan/ Usha (For fixing in Kitchen)

S & F exhaust fan AC single phase 230 V, 150 mm sweep, heavy duty with louvers, PVC body, blades, Insulation Class A including capacitor complete all as specified and directed by Engineer-in-charge( including making hole on exixting wall and making good surface of wall with necessary PCC Work and plaster etc.) . Make :-Model : Ventil Air-DB 150 mm of Havells and equavalant of GEC/Bajaj/ CG/ Khaitan/ Usha

Dismantling /disconnecting LT cables of any size with accessories. Old unserviceable of any type broken or damaged cables fitting on poles / laid in trenches and keeping aside for further disposal.

Excavation in trenches (soft soil) not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all as specified and directed :-

Returning, filling in soil, including spreading, leveling watering and well ramming in layers not exceeding 25cm all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point of any type of excavation all as specified and directed by Engineer -in-Charge.

M&L for road cutting and making good with PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) complete all as directed by Enger -in- charge.

M & L for High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed/ laid in complete to walls, ceilings or in floors, trenches etc. for cable protection of the following outer dia 40mm.

Supply & Laying cable XLPE insulated screened PVC bedded ,galvanized steel strip or wire armoured ,electric power cable heavy duty 1100 volts grade with strandad aluminum conducter of 25 sq. mm X 4 core :- Make :- Havells/ Polycab/ Gloster

Supply and fixing, testing and commissioning outdoor weather proof cubical panel board with size of 750x750x400mm made out of 3.15mm thick CRCA sheet duly powder coated with locking arrangement on both sides opened, mounted over 50x50x6mm angle iron stand at the bottom of height less than 45 cm above ground level and not less than 30cm in ground / floor mounted duly grounted in PCC 1:3:6 type C1( using 20mm graded stone aggregate) factory made duly powder coated and 300amps aluminium bus bar including panel wiring complete comprising of following :- (a) Voltmeter 0-415 Volts. (b) Ammeter 0-50 Amps. (c) Indicator lamp - 03 Nos (d) MCB TPN 63 A - 02 No. (for outgoing) (e) MCCB 4 Pole 100 A - 01 No. (for incomer) (f) Single phase/dry run protection system (g) CTs 50/ 5 ma - 1 Set (h) Busbar 200 Amp - 1 set complete wiring of panel & Installation all as specified.

Supply and fix Gun Metal Globe or Gate Valves 25mm with iron wheel head, screwed both ends for iron pipes. Make : Zoloto/Kirloskar/BIR

Supply and fix Gun Metal Globe or Gate Valves 50mm with iron wheel head, screwed both ends for iron pipes. Make : Zoloto/Kirloskar/BIR

Supply and fix Gun Metal Globe or Gate Valves 20mm with iron wheel head, screwed both ends for iron pipes. Make : Zoloto/Kirloskar/BIR

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

M&L for cutting existing steel tubes for alterations or additions for coonectio of 25mm bore all as directed

S Y Itkar Construction and Company (BID ID -3318790)

DR J S CHADHA AND SONS (BID ID -3318144)