CONSTURCTION OF LABORATORY AT PM SHRI KV No 2 AND SPL REPAIR TO SECURITY FENCING AND MAIN GATE OF GE (A) No 1 UNDER THE AREA OF AGE B/R-II OF GE (A) No 1 JODHPUR

Amount

Surface excavation in Hard/Dense soil n exc 30 cm deep and avg 15 cm deep and getting out complete all as specified and as directed .

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, less pits, manholes etc not exceeding 10 sqm on plain and not exceeding 1.50M in depth and getting out in any type of soil, complete all as specified and as directed .

M&L for Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in soils complete all as specified and directed.

M&L for sand filling under floors or in foundations inclulding watering and consolidation complete all as specified and as directed.

M&L Hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, compacting with power roller, complete all as specified and as directed.

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M&L PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in foundation , filling, sub base and mass concerete complete all as specified and as directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface and complete all as specified and directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as in footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as in column, pillars, piers, posts and strut etc, complete all as specified and as directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as Beams, cantilevers, roof beam, floor beam, bressummers, lintels over 1.5m span, complete all as specified and as directed.

M&L for design mix RCC M-25 (using 20mm graded aggregate) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L for 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all as specified and as directed.

M&L for 50 mm thick Cement concrete type C1 -1:3:6 using 20mm graded stone agg as in plinth protection & finishing the surfaxe even & smooth w/o using extra cement complete all as specified and as directed.

S&F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 5 dia and over upto and including 10 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) and similar works fair finished surfaces of concrete complete all as specified and as directed.

M&L for formwork to Edges of concrete flats, treads, breaks in floors.concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC band in walls, sloping and similar work for fair finished surfaces. Rough finished surfaces of concrete flat, complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter of flate and fair finish surface complete all as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions of square, rectangular or polygonal fair finished surfaces complete all as specified and as directed by Emgr-in-charge.

Use and waste Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat, complete all as specified and as directed.

M&L, 15mm thick rendering in CM 1:6 to Stone masonary surfaces trowelled to even & smooth w/o using extra cement. complete all as specified and as directed.

M&L Rendering 5mm thick on fair faces of concrete surfaces in CM (1:3) in ceiling complete all as specified and as directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM (1:4) surface finished even and smooth without using extra cement complete all as specified and directed. Note -Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures.

M&L Preparing of new plastered Wall surface and applying with 2 mm thick putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces on walls complete all as specified and as directed.

M&L Preparing of new plastered Ceiling surface and applying with 2 mm thick putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces on ceiling etc, complete all as specified and as directed.

M&L for fabrication of Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & as directed.

S&F Sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares n exc 0.5 sq of pane complete all as specified & as directed.

S&F Anodised aluminium frame powder coated (Thickness of powder coating not less than 50 micron) for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.

S&F Anodised aluminium door/window/ventilators shutters powder coating of any colour (Thickness of powder coating not less than 50 micron) , aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F for sheet glass 4 mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

M&L for PVC insulation panel 10mm thick with EPS stuck to 1mm plain PVC sheet suitably placed in aluminium frame work as per specification complete all as specified and as directed.

S&F 200 mm long aluminium anodised tower bolt, complete all as specified and directed.

S&F 150 mm long aluminium anodised tower bolt, complete all as specified and directed.

S&F 150mm long aluminium alloy anodised handle extruded section, complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3 universal type,suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 Kg complete all as specified and as directed.

M&L for 18-20mm thick Black Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, slabs for oval type WHB, sink, cooking platforms and like including & over 15 mm thick screeding in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, providing suitable dia hole in the slab for the gas pipe / water supply pipes etc, complete all as specified and as directed.

M&L for carrying out water proofing treatment for roofs in the following stages - (i) Rendering 10mm thick in cement mortar (1:4), mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement.Note : (WPC shell be measured separately and paid for under respective item of schedule). (ii) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. Note : - The work shall be executed by the authorized applicator of the manufacturer only. Note : - 1.The authorized applicator of manufacturer shall be approved by GE. 2.The color of final finish shall be decided by the GE

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

S&F of decorative type curtain rod stainless steel finish of pipe 22 to 25mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end, complete all as specified and as directed.

M&L precast cement concrete block masonry using PCC 1:3:6, type C-1 solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

S&F anodised aluminium snap grid frame work for ceiling 605 x 605 mm using aluminium anodised main tee of size 36.5 x 24 x 1.4mm, Cross Tee of size 23.50 x 26.40 x 1.40mm and angle of size 40 x 25 x 2mm including cutting, drilling, jointing etc. Complete including provision of 3.15mm dia GI wire suspenders fixed with adjustable connectors complete all as specified and directed.

Providing and fixing gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L for double charged vitrified ceramic tiles 10 mm thick light shed (square/ rectangular) polished, area of each tiles not exceeding 0.42 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) all as specified and as directed by Engr -in-charge.

S&F Kitchen sink without drainage board made of stainless steel 1mm thick with plug, washers and waste Including bedding in cement mortar or Including fixing cantilever brackets and connecting union to pipe overall size 495mmx420mm & bowl size 410mm x 330mm x 160mm including brass waste coupling, PVC wastepipe all as specified and as directed .

S&F of CP bib taps 15mm dia, cast copper alloy fancy type, long body screwed for iron pipe or for brass ferrule , complete all as specified and directed.

S&F Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including dismantling of old unservisiable PVC/RCC tank etc, complete all as specified and as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore and fixed, complete all as specified and directed.

S&F Ball valves PTMT 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Supplying and laying of CPVC pipes 25mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed.

Supplying and laying of CPVC pipes 20mm OD SDR 11 & Plain CPVC SDR 11 fittings in walls incl cutting or laying in floors complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with acces door complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75mm PVC (SWR) junction double, (double T), equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F Salt glazed stoneware gully traps of size 150 x 150 mm, square or rounded mouthed, type `P' fixed in CM 1:6 and cover with RCC cover slab of size 200 X 200 X 50mm incl necessary exc, pcc etc. complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in concrete bed to drain pipe 150mm bore including packing under and haunching against the sides of pipes after they are laid down and tested complete.(i) Haunching over off set of foundation of manhole shall be measured alongwith foundation of manhole etc, complete all as specified and as directed. (ii) Thickness of concrete bed shall be 10cm. (iii) Pipe shall be measured and paid for separately.

M&L Salted glazed stone ware drain pipes 150mm bore class ‘A’ laid on concrete bed and jointed complete all as specified and directed.

Cutting into manhole opening in stone masonry walls (any descript-ion) for conect to new pipeline (150 mm bore) other openings (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc.

M&L for Brickwork with fly ash old size burnt bricks, straight or curved on plan exc 6m mean radius, built in and plinth in:Cement mortar 1:4 in foundation, above plinth level upto two stories in all shapes and sizes all as specified and as directed by Engr-in-charge.

M&L PCC in surface channels and drains type B1 (1:2:4) using 20 mm graded stone aggregate, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extgra cement including forms, moulds mitred/stopped ends etc complete all as specified and as directed..

M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) mixed with water proofing compound 3% by weight of cement finished even & smooth without using extra cement ( WPC shall be measured & paid separately) complete all as specified and as directed..

M&L for 10 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM (1:4) surface finished even and smooth with WPC ( without using extra cement) etc, complete all as specified and directed. Note -(i) Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures. (ii) WPC shall be paid and measured sapartively.

Supplying only Integral waterproofing compound (ISI Marked)

M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:6) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and as directed..

S&F 18mm thick Solid UPVC (WPC) of density not less than 0.60 gm/CM3 decorative face on one faces and other face are white ; fixed with screws to timber frame/cement surface incl all necessary required fittings work as in wardrobe shutter complete all as specified and as directed..

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved sample.

S & F Auto-hinges, Brass, bright finish complete all as directed

Dismantling of barbed wire / Concertina coil etc, any type and any size complete all as specified and as directed.

Dismantling structural steel work including doors,gates but excluding framed truss etc. complete all as specified and as directed.

Dismantling of RCC fencing post , Iron post or struts of any description/section including taking out embeded ,barbed wire in concrete and making good complete all as specified and as directed.

Excavation in post holes each not exceeding 0.5 cu.m, getting out in any type of soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 using 40mm graded crushed stone aggregate as in post holes filling and mass concrete complete all as specified and directed.

M&L for precast cement concrete block masonry with solid building blocks type B1 1:2:4 (20mm graded stone aggregate) exc.10cm in width and setting in mortar 1:4 complete all asspecified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L precast cement concrete (1:2:4) type B-1using 20mm graded crushed stone aggregate as in kerb stone or mud steps, coping, bed plates, plinth course, parapets and like weathering, slightly rounded or chamfered on edge and angles throating , fixing of holdfast and including use and waste of necessary form work etc, and setting in CM 1:4 complete all as specified & directed by Engineer-in-charge.

M&L for angle iron section with swain neck as in fencing posts struts including notching drilling holes for wire mesh etc and flat iron fillets for securing wire mesh etc including all necessary drilling, bolting or riveting and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for framed work as in door or gates of angle ,MS hollow pipes, solid SQ sections Flat iron etc or other section with gusset plates, rails, braces etc complete with steel sheetingas required to br prepared for hanging or sliding with and including MS Channel as posts & hold fasts & suitable arrangements for locking etc complete all as specified & directed conforming to Fe 290.Gde E165.

M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and scrfewed the other, each screwed end to be fitted with washeres and one haxagonal or square nut not exceeding 5cm long with daia of neck 5 to 11 mm complete all as specified and directed.

Supply only chain link mild steel galvanised iron fencing, any size or type(size as approved by GE) complete all as specified and as directed. Note:- Weight of chain link will be determined by BOO constituted by GE.

Fixing only chain link fencing including line wires,any mesh,size and type to any type of standards,rails, straining bolts, etc including provision of binding wire complete all as specified and as directed.

S&F Mild steel round or square bars 10mm dia.,in available length Fe-410W (Gde-250) or Fe-290 (Gde-165) for fixing of chain link fencing complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified and as directed.

S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, fencing etc complete all as specified and as directed. Note : - Each line wire to be measured.

Supply and Fixing of concertina coil as 600mm dia rounded 50 circuls covering in 10RM with necessary fixing material complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed.

S&F of Fibre glass reinforced translucent 3 mm thick plan sheeting with two side lap fixed with coach screw and washer in fencing, wall etc complete all as specified and as directed.

Demolition of stone / boulder masonry walling, built in cement mortar including all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed.

M&L for face work masonry with 100-125 mm thick white / chitter sand stone having rock face bushings not less than 15-20 mm including chisel drafted margin 20-25 mm wide as per Jodhpur Pattern (KADAOU) regular coursed well bonded bedded & solidly hearted built in CM 1:4 complete all as specified . Height of Kadaou stone course shall not be less than 200mm all as directed.

M&L for sand stone moulded weathered copings, window cills and likes etc, setting in CM 1:6 with corbelling, throatings all as per design,etc complete all as specified and as directed.

M&L for keyed pointing to kadaou facework of Jodhpur sandstone in CM 1:3 using white cement & pigment to match the shade of the stone, all as directed.

Taking down old sand stone/precast cement concrete chattri over all size 0.6x0.75x1.2m removal away frome site etc complete all as specified and directed.

M&L for fixing in position of sand stone chattri Jodhpur pattern, octagonal shape, each side of length 45 to 65 cm & height not less than 0.9m (upto bottom level of dome), incl 8 nos sand stone columns, sand stone arches , brackets & sand stone dome slab of minimum 75 cm height of approved shape & carvings incl 1 no brass finials of height 0.30 m complete all as per trade pattern of interlocking & fixing of parts with suitable solvent cement adhesive all as directed

Demolition of Cement concrete (including cutting of reinforcement if any) in any description and any position not otherwise specifically provided forand removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L for RCC nominal mix type B1, 1:2:4 (20mm graded aggregate) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.

M&L for RCC nominal mix type B1, 1:2:4 (20mm graded aggregate) for Columns, pillars, piers, posts etc complete all as specified and directed.

S & F mild steel TMT bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15cm thickness ( below or above ground level) of any description and removing rubbish to out side MD land complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand etc, complete all as specified and as directed.

M&L precast cement concrete (1:2:4) type B-1using 20mm graded crushed stone aggregate as in kerb stone or mud steps, coping, rounded or chamfered on edge, fixing of holdfast etc and setting in cement mortar of 1:4 complete all as specified & directed.

M & L for fixing letters fabricated from 3mm thick stainless steel sheet with mirror optic finish complete of size 35-45 cm height in English/hindi fonts complete with nut & bolts complete all as specified and as directed.

M&L for 1 mm Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

M&L for Point wiring (Concealed) using approved colour coding as per IS Red/Yellow/Blue, Black and green for single phase circuits) with multi stranded copper conductor 1.5 Sqmm nominal cross area single core PVC insulated and unsheathed FR LSH cable 1100 Volts grade ISI 694 marked with valid CML No. in and including medium grade PVC concealed conduit (including Cutting Chases and make good the distrubed surfaces as per existing finishes) of dia not less than 20mm and conduit accessories ISI marked with valid CML No. ( IS 9537 -1983 for wall/roof /floor etc with pressed flush metal boxes covered with inner plates & outer plates etc suitable for mounting of Modular switches & sockets including PVC insulated multi stranded copper conductor FRLSH 1.5 sqmm nominal cross sectional area single core FRLSH cable as earth continully conductor to commonearth and connecting to earrth dolly suitable for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed. Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates

All as per Sr. item No. 114.00 here-in-above, but suitable for One socket outlet 3 pin 5 Amps on same board

All as per Sr. item No. 114.00 here-in-above, but suitable for One socket outlet 3 pin 5 Amp on independent board

All as per Sr. item No. 114.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable (FRLSH)and 2.5 sq mm PVC insulated unsheathed stranded copper conductor(FRLSH) for common earth wire for 3 pin 16 Amp socket outlet on independent board .

All as per Sr. item No. 114.00 here-in-above, but with using 4.0 Sq mm single core multistanded copper conductor cable (FRLSH)and 4.0 sq mm PVC insulated unsheathed stranded copper conductor(FRLSH) for common earth wire for 3 pin 16 Amp socket outlet on independent board .

S&F Modular switch flush type single pole and make 6 amp one way 230 V, complete all as specified & directed .

S&F Modular switch flush type single pole and make 16 amp one way 230 V, complete all as specified & directed .

S&F Modular socket outlet Any Type and make, 6 amp 1,5 Pin one way 230 V, complete all as specified & directed .

S&F Modular socket outlet Any Type and make, 16 amp 1, 6 Pin one way 230 V complete all as specified & directed .

S & F modular socketed stepped (2 module) type electronic fan regulator flush type ISI makred complete all as specified & directed .

M&L for Ceiling rose, 3 terminals bakelite body, 230 volts, complete all as specified and directed.

S&F bldg/street security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI bracket of suitable size including drilling holes, and incl MS clamp of F1 40mm X 6mm with nuts & bolts & washers and incl 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and as directed.

Supply and fix 2'x2' energy efficient recess mounting 36 watt LED lumanaries fixing for POP/snapgrid ceiling housing including LED lamps other accessories and necessary electric connection white/ warm white complete all as specified and as directed.

S&Fof ceiling fan 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE 5 star rating, brushless direct current motor (BLDC), suitable for single Phase 230 volts and connected with twin core twisted flexible copper conductor cable from ceiling rose to fitting complete all as specified and as directed.

S&F of Heavy duty Exhaust fan 300 mm sweep, 900 RPM, including louvers with cutting chases on brick wall and grounting with nut bolts, complete all as specified and as directed.

S&F Vertical Distribution Board, double Door, suitable for and including 'A' Frame FP MCCB 100A made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 6 way, 415 volts with bus bar rating 300 Amps, dust and vermin proof, suitable for incorporation of MCB’s and MCCB etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Note:- MCCB's and MCB's measured and paid seperately.

S&F MCCB, A Frame, thermal adjustable magnectic setting, Ics = 75% 25 kA, 415V, 100 Amp, 4 Pole MCCB with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 KA, 63Amp, SPN with over load and short circuit protection, , complete all as specified and directed.

S&F MCB, B Curve type, 10 KA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as specified and directed.

S&F single pole and neutral enclosure with two pin and earth plug socket complete with one single pole MCB 20 Amp 'C' curve type 230 Volts, 10 KA , complete all as specified and directed..

M&L for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as specified and directed. Note:- Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces.

M&L for earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, nnected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 5 connected to Earthing test point all as ecified or indicated including testing on completion( Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover & GI 15 mm dia protection pipe upto 7.5 mtr. lead etc. complete ) etc , complete all as specified and directed.

Supply, laying testing in trenches LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 25 sqmm 3.5 core etc, complete all as specified and directed. Note : Earth work and brick work measured and paid separately

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type I, flat, size 300 mm x 180mm x 40mm complete laid over the cable perpendicular to the cable for protection, complete all as specified and as directed.

Supply and filling dry clean sand (tibba sand) in trenches for cushioning of underground cable and punning for cushioning to cable complete all as specified and directed . Note :- Punned thicknes only shall be measured for the purpose of payment.

Supply and fix in replacement of GI tubing of size 40mm bore, medium grade for protection of cables on poles / under road crossing complete all as specified and as directed.

S&F wall mountaed air circulated fan 230 V AC 450mm sweep complete grouting at wall with fastener of suitable size complete all as specified and as directed.

Supply, installation, testing and commissioning split type Air Conditioner Electric Driven (Single phase ), cooling Capacity 2 TR BEE 3 Star Rated 2 ton, Split Air Conditioner, Nominal Capacity: 2 Ton, Colling Capacity- 60 KW+ 2%, Electricity input: 230V/50Hz/Single Phase, Cofficient of perofrmance: 3.5 (Minimum), Max Ambient Tempretaure: 480 C + 5% , Moisture removal rate : 2 + 10 % Litre/ hour, Air flow rate: 5.6 cmn (Minimum), Noise Level, Indoor Unit: less that 45 db, Outdor unit: less than 55 db, Function modes: Auto/ Cool/ Fan/ Dry have sleep and power saving modes, Other features: Automated vertical swing for horizontal louvers, Compress: Rotary Type, Body surface finish: powder coated/ high quality paint finish, Air filtering unit: Activated carbon cartridge, dust proof and anti bacteria filter, lenght of tubings: 0.5 m or as per the installation requirement, Remote handset: LCD display with night glow, incl all necessary accessories like copper tubes With insulation puffs. Drainage pipe of Required length as per site Requirement. Stand for mounting the outdoor unit on Wall/roof. Gas charging if required, etc complete all as specified and directed by Engr-in-Charge.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA, complete all as specified and directed.

M&L for road cutting (not more than 3.5 mtr in width of road) and excavation upto 60 cm below ground level and laying of 5 running mtr protection 40 mm dia GI pipe of medium grade and make good distrubuted surface by PCC 1:4:8 (nominal mix), type D-2, using 40mm graded curshed stone aggregate complete all as directed.

Note:- (i)- Qty's have been clubbed from 2 Nos sanction Job's, whose details as per appx NOTE:- (i)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

Aksher Construction Company (BID ID -3482455)

Chamunda construction company (BID ID -3477373)