Balance work of Health Sub Centre at Sahoura in G.P. Sahoura Tehsil and Distt. kangra (HP)

Amount

Excavation in foundation, trenches etc. In earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, dewatering, including weding out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, dewatering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs. (Three metres) clear from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimetre) layefrs, when requirede into plinths, sides of foundation etc. consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of material and other incidentals.

Excavation in drains and channels etcetera in earth work in all kinds of classification of soil such as pick work, jumper work, blasting work, pick jumper blasting work, hard blasting work including chiseling or wedging out rocks where blasting is prohibited and doing work in saturated soil including cost of shoring, strutting and pumping or bailing out water (surface and sub soil water) upto any depth and any quantum of water including clearing of slush which may arise out during dewatering including dressing of sides and bed and disposing of all excavated earth upto any leads and lifts, disposed earth to be leveled and neatly dressed as per direction of the Engineer-in-Charge, including carriage of materials within all leads and lifts and other incidental.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick welded with angle iron in frames 30x30x5mm (Thirty into thirty into five millimetres) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies, heights of propping and centring below supporting floor to ceiling upto any heights and removal of the same for in-situ- reinforced concrete and plain concrete work in: Flat surfaces such as soffits of suspended floors, roofs landings shelves and the like floor etcetera upto any thickness upto all floor level including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, sale tax, malkana and all other taxes as imposed by the Government.

Providing and laying reinforced cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty newton per square millimetre) with cement contents not less than 320 Kgs/m3 (three hundred twenty kilogrammes per Cubicmetre) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation and plinth including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 ( Twenty newton per square millimetre) with cement contents not less than 320 Kgs/m3 (three hundred twenty kilogrammes per Cubicmetre) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their support balconies, lintel beams, girders, breassumers and cantilever all depth/thickness up to plinth to all floor levels, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying Tor steel reinforcement for Reinforced cement concrete work including cutting, straighting, bending, binding and placing in position, including cost of binding wire complete for all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Filling in Plinth with sand under floors including watering ramming and consolidating and dressing complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Random rubble masonry/ polygonal rubble masonry (uncoursed/ brought to courses with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement isto Six Sand isto Twelve graded crushed stone aggregate 20mm (Twenty milimetre) nominal size) at plinth level in cement mortar 1:6 (One cement isto Six Sand). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and laying 30x30x2.5 cm (Thirty into Thirty into Two point five centimetre) automatic hydraulically compressed and polished precast terrazzo tiles of ISI marked No.IS-1237 (50% white and 50% grey cement) of approved shade 20mm (Twenty millimetres) thick with white yellow green & maroon marble chips 0.B and 2B size of NTC or its equivalent of specified sizes in floors, treads of steps and landing on a bed of 25mm (Twenty five millimetres) average thickness of cement plaster 1:6 (one cement isto Six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing with tiles of silver grey shade complete in all respect upto all floor level, including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

White glazed tiles 6mm (Six milimetre) thick 30x30cm (Thirty into Thirty centimetre) in skirting, risers of steps and dado 12mm (Twelve milimetre) thick cement mortar 1:3 (One cement isto Three Sand) and jointed with cement slurry, including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying 30x30x2.5 cm (Thirty into Thirty into Two point five centimetre) automatic hydraulically compressed and polished precast terrazzo tiles of ISI marked No.IS-1237of approved shade 20mm (Twenty millimetres) thick with white yellow green & maroon marble chips 0.B and 2B size of NTC or its equivalent of specified sizes in skirting and risers of steps and dado upto any heights laid on 10mm (Ten millimetres) average thickness of cement plaster 1:3 (one cement : three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of medium shade complete in all respect upto all floor level, including carriage of materials within all leads, lifts and other incidental Charges. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying reinforced cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 ( Twenty newton per square milimetre) with cement contents not less than 320 Kgs/m3 (three hundred twenty kilogrammes per Cubicmetre) 20mm (Twenty milimetre) crushed stone aggregate mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landing but including preparing of top surface and finishing of nosing upto floor all level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, sale tax or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen milimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five milimetres) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stair cases with slopping or stepped soffits excluding landing. The rate is inclusive for carriage of materials within all leads, lifts of materials and other incidentals.

Steel work welded in built up sections, trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paint in trusses and trussed purlins in building, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, sale tax or any other taxes imposed by the Government.

Providing 0.63mm (Zero decimal Six Three milimetre) thick plain G.I. sheet roofing fixed with galvanized iron J or L hooks, bolts and nuts 8mm (Eight milimetre) diameter with bitumen and G.I. limpet washers filled with white lead complete excljuding the c ost of purlins, rafters and trusses complete. Including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing flush door shutters interior grade phenol bonded (Alpro or equivalent) ISI marked No.IS:22902/Factory made panelled door ISI marked No.IS-1003 construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneer on both faces of shutters (40mm (Forty milimetre) thick including black enamelled M.S. butt hinges, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, sale tax or any other taxes imposed by the Government.

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections joints mitred and welded with 16x3.15mm(Sixteen into three decimal fifteen milimetres) lugs 10cm (Ten centimetres) long welded with steel frame and with steel plugs and screws or rawl plugs screws or with fixing clips or with bolts and nuts as required and iron fitting, including providing and fixing of glass pans with glazing clips and special metal sash putty of approved make complete including applying a coat of read lead paints within all leads, lifts of materials and other incidentals.

Fixed Steel windows

Side hung windows

Top hung Ventilators

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of IS gauge designation 85-G with a wire of dia 0.56(Zero decimal Fifty six milimetres) for doors and windows and clerestory windows including bright finished black enameled iron hinges with necessary screws 40mm (Forty milimetres) 2nd class deodar wood, within all leads and lifts and other incidentals.

Providing and fixing 40mm (Forty milimetre) thick second class deodar wood paneled glazed or paneled and glazed shutters for doors and windows including black enameled iron butt hinges with necessary screws. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plasters in single coat on rough side of brick /concrete/stone walls for interior plastering upto all floor level including arises , internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1.6 (One cement isto Six sand). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

15mm (Fifteen milimetres) thick cement plasters in single coat on fair side of brick /concrete/stone walls for interior plastering upto all floor level including arises , internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1.6 (One cement isto Six sand). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

6mm (Six millimetres) thick cement plaster to ceiling with cement mortar 1:3 (One cement : three sand) upto all floors level complete including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, sale tax, malkana and all other taxes as imposed by the Government.

Applying Birla J.k. white wall care putty over plaster surface after thoroughly brushing the surface free from mortar droping, dirt, dust, loose materials and other foreign matters sand papered smooth to give final matt finish to the surface complete upto all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials. Including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat with Asian/ Nerolac enamel paint or equivalent over new wood and wood based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease dirt and other foreign matter sand papering and knotting complete ready mixed paint brushing wood primer pink, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint of Asian/Nerolac or its equivalent brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter Enamel paint other than white, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Applying priming coat over new steel and other metal based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease, dirt and other foreign matter and required with wire brushes/ fine steel wool scrappers and sand papered complete with ready mixed priming paint brushing red lead oxide/ zinc oxide chrome complete, including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, sale tax, malkana and all other taxes as imposed by the Government.

Painting two or more coats (excluding priming coat) on new steel and other metal surface under coat with enamel paint other than white of approved brand brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter, including carriage of materials within all leads, lifts and other incidental Charges. The rate includes, royality charges, octroi, sale tax, malkana and all other taxes as imposed by the Government.

Providing and fixing 250mmx10mm (Two hundred fifty milimetre into Ten milimetre) anodized aluminum tower bolts (Barrel type) make of PILOT/SHEEL or equivalent anodized transparent or dyed to required shade and colour with screws etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 150x10mm (One hundred fifty into Ten milimetre) M.S. Tower bolt (Barrel type) with necessary screws etc. Complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred milimetre) M.S. Handles with necessary screws etc. Complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 125mm (One hundred twenty five milimetres) size aluminium anodized PILOT/ Sheel or equivalent handles anodized transparent or dyed to required colour and shade with necessary screws etc. completed within all leads, lifts of materials and other incidentals.

Providing and fixing 100mmx10mm (One hundred milimetre into Ten milimetre) anodized aluminum tower bolts (Barrel type) make of PILOT/SHEEL or equivalent anodized transparent or dyed to required shade and colour with screws etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 150mm (One hundred milimetre) Oxidized M.S. Hooks and eyes complete in all respect. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. With PVC/neoprean gasket etc. Complete as per the architectural drawings and the directions of Engineer-in-Charge (Cost of aluminium snap beading shall be paid in basic item) glazing with glass panes of 4mm (Four milimetre) thicknss (weight not less than 10.00/ kg/sqm). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 19mm (Nineteen milimetre) thick water proof termite resistant commercial board of Uniply/Greenply or its equivalent ISI mark maked IS No.1659 in SDB shutter with 6mm (Six milimetre) hard wood edging and 0.63mm (Zero point six three milimetre) thick P.G.I. lining of the shutter inner side including fixing with nickel plated piano hinges with screws etc. complete. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals as per specification and the direction of Engineer-in-Charge.

Providing under layer for Plinth protection of 100 mm (One hundred milimetre) thick unconsolidated) bed of dry brick stone broken aggregate 40mm (Forty Milimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground within all leads, lifts of material and other incidentals as per the direction of Engineer-in-Charge.

Providing Plinth protection 50mm(Fifty milimetre) thick with cement concrete 1:3:6 (One cement isto Three sand isto Six graded stone aggregate 20mm (Twenty milimetre)nominal size including finishing the top surface of concrete smooth within all leadsand lifts of material and other incidentals as per the direction of Engineer-in-Charge.

Providing and laying 605x605mm (Six hundred five into Six hundred five milimetre) double charge/ uitra charge vitrified tiles of Kajaria/ Nitco/ Orient-Bell/Rak or its equivalent in flooring on a bed of 12mm (Twelve milimetre) thick cement mortar 1:3 (One cement isto Three Sand) finished with flush painting in white cement mixed with an pigment of required shade to match the shade of tiles complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying reinforced cement concrete work of grade M-20 (M- Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 ( Twenty newton per square millimetre) with cement contents not less than 320 Kgs/m3 (three hundred twenty kilogrammes per Cubicmetre) 20mm (Twenty milimetre) crushed stone aggregate mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their support balconies, lintel beams, girders, breassumers and cantilever all depth/thickness up to plinth to all floor level, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, sale tax or any other taxes imposed by the Government.

Providing and laying 20mm (Twenty milimetre) average thick granite stone in flooring over 20mm (Twenty milimetre) (average) thickness base of cement mortar 1:3 (One cement isto Three Sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete in all respect as per direction of Engineer-in-Charge. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1:3 (One cement isto Three Sand). The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

15 mm (Fifteen milimetre) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:3 (One cement isto Three sand) within all leads, lifts, and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing vittreous china wash down water closet squatting pan Indian type W.C. Pan seat No.20090 (Twenty thousand ninety) of size 53x41cm (Fifty three into Forty one centimetre) with white shade of Hindware/Jaquar/Cera of Star white/Snow white shade Orissa pattern (earth work,bed concrete, foot rest and trap to be measured and paid for separately), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixng Vitreous china wash down water closet European type W.C. Pan S.No.20087 (Twenty thousand eighty seven) (S-18) of size 57x35x39cm (Fifty seven into thirty five into thirty nine centimetre) of Hindware/Jaquar/Cera of Star white/Snow white shade and its equivalent with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (One Cement isto One Sand) (Earth work and bed concrete to be measured and paid for separately) Indian Universal closet, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing Sand Cast Iron 100mm (One hundred milimetre) size P or S trap for water closer (squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1 (One cement isto One Sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 10.00 Ltrs (Ten Litres) capacity P.V.C. (Poly Venyl Chloride) low level flushing cistern I.S. (Indian Standard) marked No.21028 (Twenty one thousand twenty eight) of Hindware /Cera/ Jaquar star white with a pair of C.I. (Cast Iron) or M.S. (mild steel) brackets, with fittings such as lead valve less siphon, 15mm (Fifteen milimetre) nominal size brass ball valve with polythene float, C.P. (Chromium Plated) brass handle unions and couplings for connections with inlet, outlet and overflow pipes, 40mm dia (Forty milimetre) diameter C.P. (Chromium Plated) flush bend including cutting holes in walls and making good the same and connection the flush bend with cistern and closet (overflow pipe to be measured and paid for separately), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing flat back 550mmx400mm (Five hundred fifty milimetre into Four hundred milimetre) vitreous china wash basin with single hole for pillar tap with C.I. Or M.S. Brackets painted white including cutting holes and making good the same but excluding fittings. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing Dora size 470x420x178mm (Four hundred seventy into Four hundred twenty into One hundred seventy eight milimetre) KC-1004 (One thousand four) of Cera or its equivalent stainless steel Kitchen sink with drain board and C.I. (Cast Iron) or M.S. (Mild Steel) brackets painted white including cutting holes in walls and making good the same but excluding the cost of fitting, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax or any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two milimetre) dia Brass waste for wash basin or sink, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two milimetre) dia M.I. Union for wash basin or sink, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two milimetre) diametre PVC Supreme/ Kishan/ Astral or equivalent waste pipe for wash basin or sink including brass check nut within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 100mm (One hundred milimetre) dia chromium plated grating of superior quality for floor, gully or Nahni trap. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into four hundred fifty milimetre) bevelled edge mirror of superior glass mounted on 6mm (Six milimetre) thick A.C. (Asbestos Cement) sheet or plywood sheet and fixed to wooden plugs with C.P. (Chromium Plated) Brass screws and washers, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 750x20mm (Seven hundred fifty hundred into twenty milimetres) Towel rail of Continetal series of Jaquar/Classic series of Hindware/Floral series of Cera I.S. marked complete with C.P. (Chromium Plated) brass brackets fixed to wooden plugs with Chromium Plated brass screws, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing Glass shelf with C.P. (Chromium Plated) brass 600x120mm (Six hundred into One hundred twenty milimetre) of Continetal series of Jaquar/Classic series of Hindware/ Floral series of Cera brackets and guard rail complete, fixed to wooden plugs with C.P. (Chromium Plated) Brass screws, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing charomium plated brass soap dish with C.P. brass brackets of continetal serious of Jaquar/ Classic seies of Hindware/ Floral series opf Cera fixed to wooden cleats with C.P. brass screws, including carriage of material within all leads and lifts and othr incidentals. The rate includes, royality charges, octroi, sale tax, malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen milimetre) diametresC.P. (Chromium Plated) Brass Bib tap No.12 with capastan head of Continetal series of Jaquar/Classic series of Hindware/ Floral series of Cera, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen milimetre) diametre of C.P. (Chromium Plated) brass angle valve without nuts and pipe of Continetal series of Jaquar/Classic series of Hindware/ Floral series of Cera. as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen milimetre) diametres C.P. (Chromium Plated) Brass Pillar tap with capstan head of Continetal series of Jaquar/Classic series of Hindware/ Floral series of Cera. as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetre) nominal bore P.V.C. (Poly Venyl Chloride) connection pipe with brass union 45cm (Forty five centimetres) length complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing water tank make P.V.C. (Poly Venyl Chloride) SINTEX having capacity of 1000 (One thousand) litres each tank ISI 12701 (Twelve thousand seven hundred one) G.I. (Galvanised Iron) necessary fitting including over flow pipe, scour pipe etectera for inlet and outlet and inside connection 15mm (Fifteen milimetre) nominal bore ball valve and marked its P.V.C. (Poly Venyl Chloride) cover with locking arrangements of good quality complete in all respect, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. (Chromium Plated) brass fullway valve with wheel of Continetal series of Jaquar/Classic series of Hindware/ Floral series of Cera 15mm (Fifteen milimetre) nominal bore. as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing brass wall valve (horizontal/ plunger type) high pressure with polythene plastic floats 15mm (Fifteen milimetre) nominal bore, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 16mm (Sixteen milimetres) nominal bore/diametres 1216 (One thousand two hundred sixteen) polythene aluminium polythene (P.E A.L.P.E.) composite pressure pipe U.V. stabilized with carbon plastic confirming to IS 15450-2004 (Fifteen thousand four hundred fifty - Two thousand four) of kitec or its equivalent for water supply including clamps at one metres spacing cutting fixing and making good the walls etcetera, but excluding the cost of fittings (internal work) pipes exposed on wall, including filling the joints with approved adhesive complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying 20mm (Twenty milimetre) nominal bore in trenches galvanuised mild steel tubes (Medium grade), tube fittings (earth work in trenches to be measured and paid separately), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying 15mm (Fifteen milimetre) nominal bore in trenches galvanuised mild steel tubes (Medium grade), tube fittings (earth work in trenches to be measured and paid separately), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five milimetre) nominal size sand cast/ cast iron spun spigot and socket soil waste and ventilating pipes (Lead caulked, joints to be measured and paid for separately), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) nominal size sand cast/ cast iron spun spigot and socket soil waste and ventilating pipes (Lead caulked, joints to be measured and paid for separately), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five milimetre) nominal diametre/ size pipe cast iron holder bats including steel bols to sand cast iron/ cast (spun) iron pipes embedded in and including cement concrete blocks 100mm x 100 x 100mm (One hundred into One hundred into One hundred milimetre) of 1:2:4 (One cement isto Two Sand isto Four graded stone aggregate 20mm (Twenty milimetre) nominal size) including cost of cutting holder and making good the walls, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) nominal diametre/ size pipe cast iron holder bats including steel bols to sand cast iron/ cast (spun) iron pipes embedded in and including cement concrete blocks 100mm x 100 x 100mm (One hundred into One hundred into One hundred milimetre) of 1:2:4 (One cement isto Two Sand isto Four graded stone aggregate 20mm (Twenty milimetre) nominal size) including cost of cutting holder and making good the walls, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five milimetre) nominal size sand cast iron/ cast iron spun fitting and accessories Plain bends of required degree (any radius), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) nominal size sand cast iron/ cast iron spun fitting and accessories Plain bends of required degree (any radius), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five milimetre) nominal size sand cast iron/ cast iron spun fitting and accessories Single equal branch of required with oval access door insertion rubber washer 3mm (Three milimetre) thick bolts and nuts, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) nominal size sand cast iron/ cast iron spun fitting and accessories single equal branch of required with oval access door insertion rubber washer 3mm (Three milimetre) thick bolts and nuts, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) nominal size sand cast iron/ cast iron spun fitting and accessories Single un-equal branch of required with oval access door insertion rubber washer 3mm (Three milimetre) thick bolts and nuts, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five milimetre) nominal size sand cast iron/ cast iron spun fitting and accessories Collar, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) nominal size sand cast iron/ cast iron spun fitting and accessories Collar, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred milimetre) dia Sand cast iron soil waste and vent pipe and fittings (as per IS:1729) E-slotted C.I. Cowl (Terminal Guard), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing lead caulked joints to sand cast iron/ cast (spun) iron pipes and fittings including testing of joints 75mm (Seventy five milimetre) nominal size/ diametre, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing lead caulked joints to sand cast iron/ cast (spun) iron pipes and fittings including testing of joints 100mm (One hundred milimetre) nominal size/ diametre, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm 9One hundred milimetre) nominal diametre cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating without vent arm complete including cost of cutting and making good the walls and floors, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Constructing manhole with R.C.C. top slab in cement concrete 1:2:4 (One cement : two sand :four graded stone aggregate 20mm (Twenty millimetres) nominal size) mix, foundation concrete 1:4:8 (One cement : four sand :eight graded/crushed stone aggregate 40mm (Forty millimetres) nominal size) inside plastering 15mm (Fifteen millimetres) thick with cement mortar 1:3 (One cement three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement : two sand : four graded crushed stone aggregate 20mm (Twenty millimetres) nominal size) finished smooth complete including curing and testing (a) inside size 800x800mm (eight hundred into eight hundred millimetres) and upto any depths and including C.I. cover with frame (light duty single seal pattern-1) 455x610mm (Four hundred fifty five into six hundred ten millimetres) internal dimension the total weight of cover and frame to be not less than 38kg (Thirty eight kilogrammes) (weight of cover 23kg (Twenty three kilogrammes) and weight of frame 15 kg (Fifteen kilogrammes) (i) with 200mm (Two hundred millimetres) thick wall of brick masonry using second class common burnt clay building bricks in cement mortar 1:3 (one cement : three sand), including carriage of materials within all leads and lifts, and other incidental charges. The rate includes, royality charges, octroi, sale tax, malkana and all other taxes as imposed by the Government.

Constructing brick masonry chamber for under ground C.I. Inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (One cement isto Five Sand) C.I. Cover with frame (light duty) 355mm x 610mm (Three hundred fifty five milimetre ito Six hundred ten milimetre) internal dimension total weight of cover with frame to be not les than 38 kg (Thirty eight kilogram) (weight of cover 23 kg (Twenty three kilogram) and weight of frame 15 kg (Fifteen kilogram) RCC top slab with 1:2:4 mix (One cement isto Two Sand isto Four graded stone aggregate 20mm (Twenty milimetre) nominal size), foundation concrete 1:5:10 (One cement isto Five Sand isto Ten graded stone aggregate 40mm (Forty milimetre) nominal size) inside plaster 15mm (Fifteen milimetre) thick with cement mortar 1:3 (One cement isto Three Sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete inside dimension 455mm x 610mm x 450mm (Four hundred fifty five milimetre into Six hundred ten milimetre into Four hundred fifty milimetre) deep single pipe line, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement isto Four Sand isto Eight graded stone aggregate 40mm (Forty milimetre) nominal size) bedding for stoneware pipe of 100mm (One hundred milimetre) internal diametres, necessary form work and curing complete, as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten milimetre) diametre Type-B conforming to BIS-13592-92 in trenches P.V.C. Supreme or equivalent pipe soil, waste and ventilating pipes fixing with adhesive mixture complete 8/4.6mm (Eight/Four point six milimetre) thick of supreme or its equivalent including entire carriage of material within all leads, lifts and other incidentals.

PARDEEP KUMAR