Loading
Loading…
Loading…
Tender Value
Refer Docs
EMD Value
₹19,850
Closing Date
7 Sept 2026, 2:00 pm
Executive Engineer, MD-III, EM, KMDA
OFFICE OF THE EXECUTIVE ENGINEER, MECHANICAL DIVISION-III. E-M SECTOR. KMDA, 1, R.N. TAGORE ROAD , KOLKATA-700076
Overhauling and servicing of Pump no.1 and 3 at RWPS (Phase-II) under 30 MGD WTP, DDM, NDDM and SDDM trans-municipal water supply scheme.
2026_KMDA_1037626_1
KMDA/EM/EE/ MD-III/NIT-09 of 2026-27 Dated- 10.08.2026
Open Tender
MECHANICAL
Item Rate
45 days
DDM, NDDM and SDDM
Please refer Tender documents.
4 documents required · 4 mandatory
₹0
₹19,850
OFFICE OF THE EXECUTIVE ENGINEER, MD-III
19 Aug 2026
19 Aug 2026
9 Sept 2026
19 Aug 2026
7 Sept 2026
19 Aug 2026
27 Aug 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1Pump no.1 is dismantled by decoupling from motor driving end and transported to workshop for refitting of Bearing & Sleeves. | |||||
| 1.01 | Opening of Pump no.1 & lifting out rotating assembly prior to decoupling from motor. | - | Each | - | - |
| 1.02 | Supply,delivery,fitting & fixing of Bearing no. 6317 for DE & NDE for Pump no. 1. [Make : SKF/FAG/Equivalent] | - | nos. | - | - |
| 1.03 | Supply,delivery & installation of shaft Sleeves for Pump no. 1. | - | nos. | - | - |
| 2Impeller set sent to workshop for repairing work.Transportation cost for the same including loading & unloading for pump no. 1. | |||||
| 3Supplying and fabricating 20 mm to 32mm thick (finished thickness) M.S. Blank Flange properly ribbed, one face machined including drilling holes as per standard table, fitting and fixing the same with M.S. flanged pipe with supply of nuts, bolts, washers, gasket etc. of best quality all complete as per specification and direction of the Engineer-in-charge. (For pump no. 1) (750 mm dia.) | |||||
| 4Reassembly the rotating shaft & impeller and sent for Dynamic balancing. The charge of dynamic balancing of pump no. 1. | |||||
| 5Fitting, fixing of complete Pump after dismantling the blank flange & from suction & delivery side and completed with motor set & alignment checked prior to fitment . After completion of job related to Pump -1. | |||||
| 6Opening of Pump no.3 & lifting out rotating assembly prior to decoupling from motor. | |||||
| 7Supplying and fabricating 20 mm to 32mm thick (finished thickness) M.S. Blank Flange properly ribbed, one face machined including drilling holes as per standard table, fitting and fixing the same with M.S. flanged pipe with supply of nuts, bolts, washers, gasket etc. of best quality all complete as per specification and direction of the Engineer-in-charge. (For pump no. 3) (750 mm dia.) | |||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.30 MB
BOQ_2548963.xls
BOQ • 0.33 MB
Docs9_MD3.pdf
Tender Documents • 0.94 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].