Estimate for repair of Office of Zilledari Kokri, Dala and Daudhar.

Amount

Mud plaster on floor and roofs 25mm thick with gobri leeping including all materials on Floor & Roofs. As per CSR Item No 15.56

Tile terracing laid dry over roof consisitng of one layer of tiles 22.86x11.43x3.83 including grouting with cement sand mortar 1:4 top surface to be left clean after wire brushing.

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified

First class burnt brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level.

Cement concrete 1:3:6 with stone ballast or shingle mixing by manual means

Scraping - cement plaster

12.5 mm thick cement plaster 1:4

20mm thick cement plaster 1:3 in two coat work

Raking out joints in lime or cement mortar and preparing the surface for repointing or replastering including cost of neat coat of cement disposal of rubbish to the dumping ground within 50 m lead

Chowkats of commercial hard wood such as Hollock confirming to ISI specification no 1003 m kiln seasoned of doors and windows including iron hold fasts, corner straps cleats, stops, bolts for hold fasts etc, complete fixed in position . Double Rebate (60mm x 150mm)

Wire gauge Hollock wood door shutter without springs housed in chowkhat. (35mm thick)

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nuts and screws etc.complete :300mm x 16mm.As per CSR Item No.17.49 a

Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. (35 mm thick)

Providing and fixing helical door spring 150mm (superior quality) including necessary screws, complete. (b) Iron helical spring

Providing & fixing 4" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Providing & fixing 6" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Providing & Fixing glass panes with nails and putty or wooden strip complete in all respect. Glazing area above 0.09 sqm. 5.0mm thick Plate glass (INDIAN)

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete.

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Finishing walls with acrylic smooth exterior paint of required shade with two coats applied @ 1.67 litre/10sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 sqm

Scraping -White wash and colour wash

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt). For shutter area above 0.50 sqm

Providing and fixing 1st quality ceramic glazed wall tiles of size 600 x 300 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles of different sizes in light colour shades made using Double Charge technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. Size 600x600 mm

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank. (i) Tripple Layer Tanks , As per CSR Item No 30.97 A

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect (C) G.I. tank nipple 25mm i/d , As per CSR Item No 30.98 ©

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in charge:- (ii) Overall size 1.5sq.mm (Un-sheathed) .As per CSR Item No 34.09(ii)

Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect. (d) C.P.brass 20mm concealed stop cock with flange

CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI markedwith the prior approval of Engineer-in?Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge. (c) CPVC SDR 11 Pipe & fitting 25mm o/d

Providing and fixing in position C.P. brass overhead shower 1 flow with shower arm with 15mm i/d inlet of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes as per IS -13592 of approved make including cutting, jointing, wastage. 110mm o/d SWR UPVC pipe line laid complete. As per CSR Item No 30.74 (iii) B (b)

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge welded conduit pipe 20mm/ 25mm dia (1.6mm thick) ISI Marked, recessed in wall etc. (i) (a) Wiring fan point (Without fan box)

Any other Item

MITTAL CONSTRUCTION COMPANY