REPAIR TO LEAKAGE SEEPAGE AND CERTAIN JOINERY WORK OF OTM/ MD ACCN AT RANIKHET UNDER GE RANIKHET

Amount

Taking down chowkats or frames exc 1.5 Sqm but not exc 4 Sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutter only area exc. 1.00 sqm & n.exc. 2.00 sqm complete all as specified and directed.

Taking down shutter only area n exc. 1.00 sqm complete all as specified and directed.

S&F 2nd class hard wood (SAL) plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints and fixed to any position including material required for fixing i,e Hold fast, cement concrete, etc complete all as specified and directed.

S&F 40mm thick (batten thickness) IInd class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) or of 12mm thick veneered particle board medium density, wood particle board with commercial face veeneers or 9 mm BWP commercial ply fixed complete all as specified and directed.

M&L for prelaminated particle board18/19mm exterior grade prelaminated one side with decorative choice and other side balancing white fixed with screw to timber frame work complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick IInd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, guage etc, with out sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, guage etc, size of members of shutters as specified in MES SSR Part-I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F 30mm thick IInd class hard wood glazed and skelton shutters open rebated but divided into squares with plain chamfered or rounded mitred and sash barsand prepared to receive glass, guage etc, with out sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, guage etc, if window, ventilators etc are provided with stiles and rails as specified size of members of shutters as specified in MES SSR Part-I, Section 8, Clause 8.24 (b) complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed. Note: stainless steel butt hinges and necessary S S screws shall be paid separately.

S&F mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings and similar work confirming to Fe.290, Gde-E-165 complete all as specified and directed.

S&F 250mm long aluminium sliding door bolt, bolt type with bright bolt not less than 12mm dia with and including a minimum of 6 bolt and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F 125 mm size aluminium handle plate type anodised complete all as specified and directed.

S&F 100 mm size aluminium handle plate type anodised complete all as specified and directed.

S&F 150mm long Aluminium tower bolt and fixed complete all as specified and directed.

S&F 100mm long Aluminium tower bolt and fixed complete all as specified and directed.

S&F 100mm size MS butt hinges, medium weight, cold rolled and fixed complete all as specified and directed.

S&F 75mm size MS butt hinges, medium weight, cold rolled and fixed complete all as specified and directed.

S&F 125 mm aluminium anodised Hasp and staple with mild steel hinge pin complete all as specified and directed.

S&F in repair Aluminium (die cast) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F in repair 150 mm floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete fixing arrangement complete all as specified and directed.

S&F in repair 375 mm helical door spring with roller plate complete all as specified and directed.

S&F in repair 150 mm MS handle fixed with screw and bolt in steel window complete all as specified and directed.

S&F in repair 300 mm MS stay fixed with screw and bolt in steel window complete all as specified and directed.

S&F in repair 150mm long brass tower bolt with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

M&L for 18/19mm thick block boards, grade 2 quality, exterior grade, commercial type, fixed with screws to timber frame work as in cup board shelf complete all as specified and directed

S&F 40mm width of flaps continuous (Piano) type hinges mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames, glazed with putty or fixed with beads including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified and directed.

Supply only 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in fixing of hold fast, bed blocks etc including necessary form work as required complete all as specified and directed.

S&F mild steel work as hold fasts, bands, straps, supports or stays for pipes eaves gutter including bolts if required, hooks (stay), clamps and similar small articles, conforming to Fe 290 Gde-E-165 complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling timber scantling in fillets , post, beading fixed in any position with nails complete all as specified and directed.

M&L for 2nd class soft wood (Chir) plain fillets, square, rectangular or triangular in section, clean sawn secured with nails cross sectional area exc 3 Sqcm but not exc 6 Sqcm complete all as specified and directed.

M&L for 2nd class soft wood (Chir) plain fillets, square, rectangular or triangular in section, clean sawn secured with nails cross sectional area exc 13 Sqcm but not exc 25 Sqcm complete all as specified and directed.

S&F three track aluminum powder coated sliding window with three sliding shutter, the size of outer frame three track 100 x 37x 1.50mm (using two track for glazed window shutter and one track for wire gauged) , the section shutter size 37 x 18 x 1.2mm) and glazing with 5 mm thick transparency glass of poly carbone including all-around suitable rubber gasket and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers’s sliding rollers of nylon with including all necessary fittings complete all as specified and directed.

Dismantling of wall paneling and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F 5 mm thick solid PVC wall lining consisting of colour single side prelam PVC sheet used instead of plain colour sheet as per specification complete all as specified and directed.

S&F 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drwaing complete all as specified and directed.

S&F size of grid 600 x 600 mm anodized aluminum snap grid frame work for false ceiling complete all as specified and directed.

M&L providing and fixing gypsum boad 9 mm thick in ceiling fixed with screw as per manufactures instruction complete all as specified and directed.

Dismantling of ceiling board (flbre pulp, insulation etc) or insulation boards/ slabs/ blankets any thickness, including cover fillets complete all as specified and directed.

S&F 4 mm thick E-Board Classic for insulation and accoustic purpose, 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surface complete all as specified and directed.

S&F of powder coated grid frame work for false celling comprising of the following sections for making partitions of 600x600 mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 4mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 28mmx24mmx0.3mm thick , cross tee shall be 28mmx24mmx0.3mm thick and wall angle shall be 24mmx24mmx0.3 mm thick complete all as specified and directed.

Cleaning of PVC water storage tanks of capacity exc 250 ltr but n.exc 2000 ltrs mechnized dewatering of water including sludge from the tanks, cleaning internal & external tank surfaces with high pressure water spray, vaccum cleaning, anti bacterial spray, UV radiation, spray of bleaching powder including writing date of cleaning (with thick paint in capital bold letter) on each tank etc complete etc complete all as specified and as directed by Engineer-in-Charge. by Engr - in- charge. Note : - Rate includes the following :- (i) Opening & closing of tank covers properly before & after execution of cleaning work. (ii) Removal & refixing of float valves of any size & description before & after execution of work. (iii) Removal of sludge where directed by Engr - in- charge. (iv) User completion certificate shall be produced by the contractor. (v) If damage the tank during the cleaning, will re-fiting with new tank with contractor's risk. (vi) If damage the float valve during the removal for re-fitting will re-fitting the same with contractor's risk.

Dismantling plain or corrugated steel sheeting/ AC sheet any guage, thickness, including nainital pattern or similar pattern roof covering complete all as specified and directed.

Dismantling of asbestos cement (corrugated or semicorrugated etc) sheets as in roof covering complete all as specified and directed.

S&F 0.63mm thick galvanised corrugated MS sheeting (CGI sheet roofing) with two corrugation side laps, using grade-O sheets with 120gm Zinc (Spelter) coating per Sqm both sides inclusive fixed with coach screws & washers and 'L' or 'J' type hooks or cranked hooks/ bolts as in roofs etc complete all as specified and directed.

S&F 0.63mm thick plain galvanised MS sheeting using grade-O sheets with 120gm Zinc (Spelter) coating Per Sqm both sides inclusives, as in roof, ridges, hips, valley gutters, drip and straight flashing complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall , fixed with self tapping screw complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall , fixed with self tapping screw complete all as specified and directed.

Taking down/ dismantling of old tarfelt/ old unserviceable roof treatment from RCC roof by scrapping, broomig and washing with water etc complete all as specified and directed.

M&L 15mm thick cement rendering in 1:3 with water proofing compound @ 3% by weight of cement over RCC roof and applying bitumen primer @ 0.30 kg/sqm and then apply hot blown bitumen grade 85/25 @ 1.2 kg/sqm and water proofing treatment by APP modified polymeric water proofing membrance (weight not less thant 3 kg /sqm) with overlap of 10 cm sealed by frame shall be laid & the overlaps sealed/fused by flame as per manufacture instructins. A coat of hot blown bitumen grade 85/25 @ 1.2 kg/sqm shall be applied on top of APP modified polymeric memberaned & finally it will be finished with a coat of aluminium paint @ 0.200Lit/sqm as per manufacture instructions complete all as specified and directed.

Dismantling of boarding any description and fixed in any position with nails complete all as specified and directed.

S&F 20mm thick 2nd class soft wood (Chir) boarding planned one side fixed with butt joints with nails in any situation/ position except flooring and skirting complete all as specified and directed.

Demolition of brick work or stone boulders masonery built in cement mortar or lime mortar including all quoins, arches pillars etc complete all as specified and directed.

M&L for brickwork with old size sub class B straight or curved on plan exc. 6 m mean radius built in CM 1:6 complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for and removal from site exc. 50 m complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate for making good of broken part of chajjas, roof projections etc. or recasting after dismantling broken portion including providing benching over chajjas from junction of wall & chajja to end of projection and making good to match with existing surface of wall including necessary form work, in diffrent quarters of cantt area complete all as specified and directed. Note-( The work shall be carried out at Ist floor/ 2nd floor . The contractor shall make necessary arrangement of scaffolding and ensure safty of Labours.

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/ tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

M&L for 15mm bore GI tubing, medium grade, galvanised with and including all GI fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L for 20mm bore GI tubing, medium grade, galvanised with and including all GI fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair 20 mm bore dia gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Dismantling water tanks 500 ltrs capacity complete all as specified and directed.

Dismantling water tanks, capacity exce 500 litres but not exc 1000 liters complete all as specified and directed.

S&F rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postion 500 ltrs capacity and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed.

S&F rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postion 1000 ltrs capacity and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed.

S&F in repair 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or PCC blocks or stone wall or concrete surface etc including racking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, finishing the surfaces fair and even complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on concrete surfaces as on ceiling and finished fair and even complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for 15 mm thick rendering CM 1:4 with WPC @ 3% by weight of cement finished even and smooth with additional thickness is provided as floating/ setting coat in vertical surfaces complete all as specified and directed. (Note- WPC shall be measured and paid seperately)

Supply only integral waterproofing compound complete all as specified and directed.

M&L for cement concrete 1:5:10 Type E-2 using 40 mm stone aggregate sunken portion filled complete all as specified and directed.

M&L 25 mm thick PCC type B-1,1:2:4 (using 20 mm graded stone aggregate) as in flooring complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in CM 1:6 for laying finishes in floors complete all as specified and directed.

M&L for 10 mm thick screed bed or bedding layer in CM 1:4 for laying finishes in vertical surfaces complete all as specified and directed.

M&L 300x450x7mm thick glazed ceramic tiles coloured, printed/ design and pattern as approved fixed as in vertical surface etc, set and jointed in neat cement slurry and pointed with white cement with colour pigment to match complete all as specified and directed.

M&L colour non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exc. 0.11 sqm but n.exc. 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement with colour pigment complete all as specified and directed.

Taking down AC rain water pipes (any size or pattern) including all fittings heads shoes bends swan necks etc complete all as specified and directed.

S&F 100 mm bore cast iron pipe (sand cast) as in soil, waste and vent pipe, in any length with or without ears, with cement joints fixed to walls with mild steel work as in small articles such as stack clamps, flat iron, stays, including bolts and nuts and securing ends of stays to wall complete all as specified and directed.

S&F 75 mm bore cast iron pipe (sand cast) as in soil waste and vent pipe, in any length with or without , with cement joints, fixed to wall with mild steel work as in small articles such as stack clamps, flat iron, stays, including bolts and nuts and securing ends of stays to wall complete all as specified and directed.

S&F in repair 100 mm dia cast iron bend (any radius) diminishing pieces or tapers including taking down existing & making good to match with existing surfaces complete all as specified and directed.

S&F in repair 75 mm dia cast iron bend (any radius) diminishing pieces or tapers including taking down existing & making good to match with existing surfaces complete all as specified and directed.

S&F in repair 75 mm dia cast iron bend (any radius) with oval access cdoor including taking down existing & making good to match with existing surfaces complete all as specified and directed.

S&F in repair CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket tyes) or with parellel branches, 100 mm bore fitted with oval access door including taking down existing & making good to match with existing surfaces complete all as specified and directed.

S&F in repair CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket tyes) or with parellel branches, 75 mm bore fitted with oval access door including taking down existing & making good to match with existing surfaces complete all as specified and directed.

M&L 100 mm CI sanitary short connection pipe of length upto 300 mm complete all as specified and directed.

S&F in repair 15 mm bore dia bib tap long body CP cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm bore dia CP stop valve/ angle cock, cast copper alloy screwed down, high pressure with crutch butterfly handle, screwed both ends for iron pipe or for unions and fixed complete complete all as specified and directed.

S&F in repair 100mm dia grating of CP complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with intregal foot rests, with & including P or S trap (excluding material & labour of flushing cistern and flush pipe) including conection to trap and to flush pipe etc complete including making good to floor complete all as specified and directed.

S&F in repair polymer white (polypropeylene delrin and ABS) low level flushing cistern 10 Ltrs capacity, valveless, syphonic action type complete with inlet, ball valve float valve, PVC connection bends brackets, rawl plug, brass screws handle etc complete having BIS description mark with IS-2731, fixed complete all as specified and directed.

Builders Harpal

M/S S R Construction

SS Construction Co

NK CONSTRUCTION

M/s RK JOSHI&SONS