ADDN ALTN CUM SPECIAL REPAIR TO CERTAIN OFFRs JCOs ORs MD ACCN UNDER GE WEST BAREILLY

Amount

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed.

M&L for non skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for non skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in vertical surfaces including rendering 10 mm thick in cement mortar 1:4, as in backing layer complete all as specified and directed.

M&L for non- skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes, including dismantling of floor tiles and floor hearth, complete all as specified and directed.

M&L for non- skid ceremic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling of tiles and screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes, complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10mm thick (square/rectangular) polished, area of each tiles exc 0.42 sqm and not exceeding 1.00 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement including 15mm thick screed bed in cement motar 1:6, including dismantling of floor tiles and floor hearth, complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10mm thick (square/rectangular) polished, area of each tiles exec 0.16 sqm and not exceeding 0.36 sqm as in vertical surfaces including dismantling of tiles and screed bed / rendering and provn of rendering 10 mm thick in cement mortar 1:4, as in backing layer complete all as specified and directed.

M&L for glazed (plain /coloured) ceramic tiles wall 600x300x7mm thick on vertical faces of walls including 10mm thick rendering in CM 1:4 set jointed in neat cement slurry and pointed in coloured cement to match including taking down old dado/skirting complete all as specified and directed.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing apron complete all as specified and directed.

M&L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame) area not exc 1.5 Sq.m each including making good disturbed portions in cement mortar 1:4 of wall with new or old bricks, lintel, cills etc. complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame) area exc 1.5 Sq.m each and not exc. 4.00 Sq.m each including making good disturbed portion in cement mortar of wall with new or old bricks, lintel, cills etc. complete all as specified and directed.

Supply and fixing fiber glass reinforced plastic (FRP) door frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame complete all as specified and as per manufacturer's instructions and as directed. Make: Giza, Ecocell, yamuna interior pvt ltd.

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (FRP) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of FRP laminate conforming to table 3 of IS: 14856 complete all as specified and as per manufacturer's instructions and as directed. Make: Giza, Ecocell, yamuna interior pvt ltd.

S&F 100mm long stainless steel butt hinges complete all as specified and directed.

S&F 150mm long aluminum anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm long aluminum handles, cast type anodised complete all as specified and directed.

S&F magnet catch with striking plate including letting in, complete all as specified and directed.

S&F pressed steel, frames 125x60mm size, 2 mm thickness for door with one or more rebates including inner surface of frame treated with a coat of bitumenous paint and filing PCC 1:3:6 type C-0 and compaction, necessary fixing lugs, hinges, lock strike plate, 02 nos 25x3mm flat iron at bottom of the frame etc, complete including wooden texture finished paint on the frame surface complete all as specified and directed.

S&F pressed steel, frames 105x60mm size, 2 mm thickness for door with one or more rebates including inner surface of frame treated with a coat of bitumenous paint and filing PCC 1:3:6 type C-0 and compaction, necessary fixing lugs, hinges, lock strike plate, 02 nos 25x3mm flat iron at bottom of the frame etc, complete including wooden texture finished paint on the frame surface complete all as specified and directed.

S&F 35 mm thick factory made flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specified and directed.

M&L for factory made 35mm thick plain framed glazed and skeleton shutter open rebated & prepared to receive glass, gauge etc, without sash bar edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc, of 2nd class hard wood , members of shutters as specified in SSR Part-I Section 8 clause 8.24 (a) fitted to chowkat complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed..

M&L for applying two coat of synthetic enamel paint over a coat of pink primer on wood or wood based surfaces of any description over 10cm in width or girth including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L preparation of old steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for applying two coat of synethic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm in width or girth including preparation of newly or previously untreated surfaces complete all as specified and directed.

S&F 200mm long fancy type stainless steel handles and fixed complete all as specified and directed.

S&F 200mm long aluminum anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring. Fixed in floor complete all as specified and directed.

S&F 300mm long mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F 1.2 mm thick aluminum anodised campsule mesh aperture not more than 1 cm fixed with screws in the door shutters for protection of mosquito wire mesh complete all as specified and directed.

S&F galvanised Stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples etc. complete all as specified and directed.

S&F mild steel ordinary rat tail rod pattern springs of 300 mm size including roller and roller plate, fixed to wooden or steel chowkats complete all as specified and directed.

S&F 20 mm thick solid PVC boards, both side prelaminated, one side with decorative choice lamination and other plain rigid white lamination as in cupboard shutters, wardrobe finch lock and PVC lipping on all exposed edges of same texture & shade, fixed with SS screws, fasteners and adhesive as per instructions of manufacturer complete all as specified and directed. Note:- (i) Design & layout of wardrobe and pattern/colour of lamination shall be approved by GE. (ii) Thickness of laminate shall not less than 0.25mm for inside rigid white type and 0.12 (14 micron) for outer side decorative type, the laminate shall be fixed to base with approved adhesive as per manufacturer's instruction and machine pressed for proper bonding to base ply & avoid air pockets. (iii) Frame to be fixed with wall, soffits & base of cupboard with fastneres etc.

S&F 18 mm thick solid PVC boards, both side prelaminated, one side with decorative choice lamination and other plain rigid white lamination as in cupboard shutters, wardrobe finch lock and PVC lipping on all exposed edges of same texture & shade, fixed with SS screws, fasteners and adhesive as per instructions of manufacturer complete all as specified and directed. Note:- (i) Design & layout of wardrobe and pattern/colour of lamination shall be approved by GE. (ii) Thickness of laminate shall not less than 0.25mm for inside rigid white type and 0.12 (14 micron) for outer side decorative type, the laminate shall be fixed to base with approved adhesive as per manufacturer's instruction and machine pressed for proper bonding to base ply & avoid air pockets. (iii) Frame to be fixed with wall, soffits & base of cupboard with fastneres etc.

S&F 16 mm thick solid PVC boards one side prelaminated and other side plain white lamination, fixed on back side of wall for cupboards & cabinets etc, fixed with SS screws, fasteners and adhesive as per instructions of manufacturer, complete all as specified and directed.

M&L for Plain Cement Concrete 1:3:6 type C-1 (using 20 mm graded stone aggregates) as in bed blocks for fixing holdfasts and similar work etc., including necessary form work complete all as specified and directed.

M&L for 15mm thick cement plaster on brick surfaces or concrete surfaces in cement mortar 1:4 using WPC 200 ml/ per 50 Kg of cement including taking down old plaster and raking out joints, hacking for key scrubbing down with water etc., finished surface even and fair including necessary scaffolding, complete all as specified and directed. (Note:- WPC shall not be measured & paid separately for this item)

M&L for 15mm thick cement plaster on brick surfaces or concrete surfaces in cement mortar 1:4 using WPC 200 ml/ per 50 Kg of cement including taking down old plaster, finished even and fair and necessary scaffolding complete all as specified and directed. (Note:- WPC shall not be measured & paid separately for this item)

M&L for 12mm thick cement plaster on brick work or concrete surfaces in cement mortar 1:6 including taking down old plaster and raking out joints, hacking for key scrubbing down with water etc., finished surface even and fair including necessary scaffolding, complete all as specified and directed.

M&L for 12mm thick cement plaster on brick work or concrete surfaces in cement mortar 1:6 finished surface even and smooth without using extra cement including necessary scaffolding, complete all as specified and directed.

M&L for rendering 5mm thick on ceiling or concrete surface in cement mortar 1:3 finish surface even and smooth without using extra cement including taking down old plaster and necessary scaffolding, complete all as spd and directed.

M&L for rendering 5mm thick on ceiling or concrete surface in cement mortar 1:3 finished the surface even and smooth without using extra cement including necessary scaffolding complete all as spd and directed.

M&L white washing three coats to ceiling surfaces including preparation of newly plastered / untreated surfaces complete all as specified and directed.

M&L for applying 2 mm thick layer of birla wall care putty on wall/ceiling surfaces incl rubbing down the surfaces with sand paper after getting dried all as directed to obtain a smooth & even surface complete all as specified and directed.

M&L for Preparation of old decorated surfaces and applying three coat of white wash on ceilings surfaces and rubbing down with sand paper to have even and smooth surfaces complete all as specified and directed.

M&L for applying two coat of distemper oil emulsion white or tinted on old decorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces by smart painting method complete all as specified and directed.

M&L for applying two coat of distemper oil emulsion white or tinted on newly decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces by smart painting method, complete all as specified and directed.

M&L for applying two coat of weather proof paint on old decorated surfaces over one coat of primer after complete removal of existing treatment including preparation of surfaces by washing rubbing down and stoping painted surfaces by smart painting method, complete all as specified and directed.

M&L for two coat of weather proof paint over one coat of primer on newly plastered undecorated surfaces of any description including preparation of surfaces by smart painting method, complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with fly ash bricks old size straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed.

M&L for cutting chases of hanging chajjas, pinning in exc 10cm and n.exc 40cm girth in RCC chajjas or brick walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja (up to IInd floor) etc., complete all as specified and directed.

Demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and stair case similar work carefully and matching to adjoining disturbed surfaces complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Use & waste form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and directed.

Use & waste form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick,complete all as specified and directed.

Use & waste formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete complete all as specified and directed.

Use & waste formwork to sides and soffits of lintels,lintel bend, beams etc finished rough surfaces of concrete complete all as specified and directed.

Use & waste formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular finishes rough surfaces of concrete.etc finished rough surfaces of concrete complete all as specified and directed.

S&F TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required,including cranking and binding with mild steel wire (annealed) not less than 0.9mm dia. complete all as specified and directed.

S&F TMT mild steel bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia. complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in slab, shelves and stair case etc. complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20mm graded stone agg) as in beams, cantilevers, lintels, over 1.5 m span complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20mm graded stone agg) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate as as in chajjas and like complete all as specified and directed.

Dismantling of concrete by chiseling from RCC members like column, beam, parapet facia, chajja, ceiling,etc exposing the reinforcement without disturbing the reinforcement, free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement providing at places additional reinforcement welding with existing reinforcement as directed wherever required binding RCC with 10 mm gauge welded mesh of aperture 50 mm x 50mm & tack , securing with clips / blinding wire, welding & provision of pressure guniting 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @ 200 ml every 50 kg of cement, cleaning and removal of loose waste material etc. and applying two coat of Dr fixit /pidilite new coat ezee at interval of 8 hours cure for the surfaces complete all as specified and directed.

Demolition of cement concrete (unreinforced), in any description paving n.exc. 15 cm thickness (below or above ground level) including tile/ terrazzo floor complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection 75 mm thick finished even and fair including forming 10 mm wide joints at not exceeding 3 m distance between adjoining slabs shall not exceed 10 mm in thickness and shall be filled with bitumen mastic i.e. bitumen and sand in proportion 1:2, complete all as specified and directed.

Providing water proofing treatment to RCC sunken slab as specified and directed as under:- (a) Cleaning the existing RCC sunken slab and vertical wall/RCC beam and hacking the surface. (b) 15mm thick plastering over the floor & vertical surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50 kg of cement trowelled to even and smooth finish without using extra cement .(Water proofing compound shall be measured and paid separately). (c ) filling the sunken portion with water for 72 hrs and carring out the ponding test.(Any leakage /seapage noticed shall be repaired). (d) Applying two coats of elastomaric acrylic water proof coating Make: Dr. Fixit of pidilite or equivalent per sqm in each coat with roller application complete all as specified and directed.. (Note: Each coat of elastomaric acrylic compound requires 6-8hrs to dry up itself second coat shall be applied on getting the first coat completely dried up.)

Supply only liquid water proofing compound complete all as specified and directed.

M&L for cement concrete type E2 1:5:10 using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed.

S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in levelling course laid over RCC roof surface including rounded or chamferred on edges etc complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of concrete surfaces in cement mortar 1:4 mixed with water proofing compound as per manufacturer's instruction, finished surface even & smooth without using extra cement, complete all as specified and directed. (NOTE:- WPC shall be measured and paid separatly)

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) in floor base even and fair to receive floor tiles complete all as specified and directed.

Supply and providing water proofing treatment with polyester based water waterproofing membrane of 3 mm thick and 3.5 kg/Sqm weight, Aquaflex manufactured by M/s Bengal Bitumen, MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/Hyperplas manufactured by IWL Ltd having 10 years guarantee for water tightness complete all as specified and directed and described as under :-

(a) Preparation of RCC roof surface by wire brushing and cleaning top surfaces including flashing and junctions of parapets etc., and applying one coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/Sqm, all as per manufacture'"s specification complete all as specified and directed.

(b) Supply & providing water proofing treatment with polymeric proofing membrane of 3 Kg/Sqm consisting of 100 micron HMHDPE film centre core including coating he surface with the compatible primer and torch application of membrane with 10 cm overlaps as required thereof, complete all as specified or as directed. Make :- IWL Hyperplas Polyster (M/S IWL), Super Thermolay (M/S STP Limited), Torch Shield AP by Pidilite Industries.

M&L for applying one coat of aluminium paint on APP membrane laid over non accessible roof, complete all as specified and directed.

M&L for heat reflective weathering tiles minimum size 250 x 250 x 15 mm thick set & jointed in neat cement slurry over and including 15 mm thick cement mortar screed in cement mortar 1:4 and joints shall be 4mm wide, sealed with 2 mm deep polysulphide/polyurethane compound (sealing compound), laid over roof top or in floors or pavings, complete all as specified and directed.

M&L for Granite (Zebra Black) stone tiles 20mm thick machine cut, laid in floors, cooking platform, window cills etc., bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over & including 15 mm thick screed bedding in cement mortar 1:6 and dismantling of existing tiles, floor hearth etc., complete all as specified and directed.

M&L for Granite (Zebra Black) stone 20mm thick, machine cut and machine polished as in pillars, jambs, riser of steps and urinal partition wash basin platform and skirting/dados etc like, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone, jointed with grey cement slurry and laid over & including cement mortar screed or plaster 10mm thick in cement mortar 1:4, including dismantling of wall tile and cement mortar bedding, complete all as specified and directed.

M&L for prepolished 20-25 mm thick machine cut, kota stone slab laid in floors, stairs case and jointed with grey cement slurry including rubbing and mirror polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 and including dismantling existing old floor floor finish and removing the rubbish off the premises, complete all as specified and directed.

M&L for prepolished 20-25 mm thick machine cut, kota stone slab in single piece as in riser of steps skirting, dado and pillar, set & jointed with grey cement slurry including rubbing & mirror polishing laid over & inclucding 10mm thick screed bed or plaster in cement mortar 1:4 including dismantling of existing old tiles/stone, complete all as specified and directed.

S&F mild steel OHT cage, bands, straps, supports or stay, for rain water, ventilating pipes including bolts if reqd, hooks (stay) heavy for large gates hook and pintle large hasps and staple, chains hand made sliding bolts clamps, hold fasts wall ties etc etc hooks for hanging fans plain angle cleats for securing purlins to wood truss or rafter, knee piece inserts, two way and three way straps, plate washer and similar small articles confirming to Fe-290 Gde - E-165 complete all as specified and directed.

S&F 15 mm thick (minimum) Johnson Endura tiles of anti skid surface as in riser & treads in steps and like, set & jointed over & including 15 mm thick screed bed in cement mortar 1:4 and pointed in white cement 1:2 using stone dust with admixture of pigment to match with shade of tiles including making 03 x self embossed tread lines in length wise with bull nosed round edge of treads, complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

S&F in repair PVC low level , valve less, syphonic action type, flushing cistern,10 ltrs capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed. Make:- Prayag Polymers Pvt Ltd Cat Part No.Duo-502/ Prism Johnson Ltd Cat Part No.P-2834PI0000/ Pearl Precision Pvt Ltd (Brand- Sparsh Pearl) C001

S&F in repair CP stop valve/angle cock two/one way 15mm dia, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union and fixed complete all as specified and directed. Make :- Grohe Cat Part No.22005000/ Kohler Cat Part No.K-23515IN-4-CP/ CERA Cat Part No. F1014151/ Kerovit (Kajaria Bathware Pvt Ltd) Cat part No. KB2111004

S&F in repairs chromium plated fancy type long body bib taps fange quarter turn, for 15 mm bore pipe, complete all as specified and directed. Make :- Grohe Cat Part No.20237001/ Kohler Cat Part No.K-16093IN-4-CP/ CERA Cat Part No. F1014151/ Kerovit (Kajaria Bathware Pvt Ltd) Cat part No. KB2111004

S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

S&F for 15mm bore galvanized steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

S&F for 20mm bore galvanized steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Refixing 15mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Refixing 20mm dia old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) complete all as specified and directed.

Dismantling water tanks and removing to store capacity exc 250 and not exc. 500 litres complete all as specified and directed.

Dismantling water tanks and removing to store capacity exc 500 and not exc.1000 litres complete all as specified and directed.

S&F 500 ltrs capacity rotational moulded polythylene triple layered water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I and complete all as specified and directed.

S&F Rotational moulded polyethylene triple layered water storage tanks of 1000 Litre capacity (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and complete all as specified and directed.

S&F 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet single piece (Cascade pattern) with seamless flushing cistern square design duroplast slim seat cover, slow falling seat cover size 69x37x77 cm, including connection to drain pipe etc complete all as specified and directed. Make:- Kerovit Cat Part No: INSIGNIS KS710/ CERA CAMPBELL Cat No S1013109/11 / Jaquar Cat Part No.ITS-WHT-89853S300PP.

S&F in repairs Vitreous China water closet squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with 'P' or 'S' trap 100 mm dia front & back inlet and integral foot rests (excluding flushing cistern and flush pipe) and connections to flushing cistern/pipe complete all as specified and directed.

S&F in repairs 0.80mm thickness stainless steel kitchen sink of undermount, single bowl with lugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and directed.

S&F stainless steel kitchen sink with double bowl with drain board made of stainless steel 1 mm thick, with plugs washers and waste pipe and coupling including bedding in cement mortar on dwarf walls including brackets and connecting union to pipe complete all as specified and directed.

S&F in repairs 75 mm x 32 mm dia chromium plated waste fitting special size suitable for stainless steel sinks including PVC flexible waste pipe of approved quality complete all as specified and directed.

S&F in repairs stainless steel grating suitable for 100 mm dia inlet fixed in repairs complete all as specified and directed.

S&F in repairs fancy type stainless steel towel rack 600mm long with pair of brass bracket in repair complete all as specified and directed. Make & Model :- Grohe Cat No 40800001/ Kohler Cat Part No.K25066IN-4-CP/ CERA Cat Part No.F5006101/ Kerovit (Kajaria Bathware Pvt Ltd) Cat part No. KA9800010

S&F in repairs vitreous china ware coloured wash hand basin table/counter top of suitable size including stainless steel bottle trap and cabinet of PVC shutter fixing on counter with CP waste coupling & waste pipe complete fixing arrangement, all as specifed and directed. Make:- Cera Cat Part No 52030104/ Kerovit Cat part No.KB2243 / Jaquar Cat part No.ARS-WHT-39601

S&F stainless steel plate rack not less than 5 Kg of size 31"X36"X10" complete all as specified and directed.

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 55X40X82cm complete including, CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed. Make:- Cera Cat Part No.S2040104 for WHB & S2090101 for Pedastal/ Kerovit Cat part No.K0284W for WHB & KO314W for Pedastal / Jaquar Cat part No. FNS-WHT-40801 for WHB & FNS-WHT-430301 for Pedastal

S&F in repairs fancy type brass chromium plated toilet paper holder, complete all as specified and directed.

S & F in repair chromium plated fancy type shower rose with or without swivel joints, any size, including fixing to steel pipe or union size 150 mm, complete all as specifed and directed. Make :-Cera Cat Part No.F7010505AB/ Kerovit Cat Part No.KA570018/ Grohe Cat Part No.26450000/ Kohler Cat Part No.K-22645IN-CP

S&F in repairs brass chromium plated wall mixer 3 in 1, 15mm for mixing hot & cold water screwed down three joints to steel pipes or union & plugging and screwed to wall complete all as specified and directed. Make:- Cera Cat Part No. F1012403 / Kerovit Cat Part No KB511018 / Grohe Cat Part No.33850001/ Kohler Cat Part No.K-98754IN-4-CP.

S&F in repairs brass chromium plated wall mixer 2 in 1, 15mm for mixing hot & cold water screwed down three joints to steel pipes or union & plugging and screwed to wall complete all as specified and directed. Make:- Cera Cat Part No. F1020411 / Kerovit Cat Part No KB411019 / Grohe Cat Part No.33849001/ Kohler Cat Part No.K-98755IN-4-CP.

S&F in repairs fancy type 15 mm dia chromium plated wall mixer, hot & cold with long swan for kitchen sink fixing and connections to pipes complete all as specified and directed. Make:- Kerovit Cat Part No KB511025 / Grohe Cat Part No.31191001 (Costa L)/ Kohler Cat Part No.K-20591IN-4-CP.

S&F 15 mm dia brass CP health faucet with 1 mtr long flexible tube and wall hook screwed for iron pipe fancy type long body and hanging arrangement complete all as specified and directed. Make:- Cera Cat Part No.F803008AB / Kerovit Cat Part No KA5800008 / Grohe Cat Part No.26332000/ Kohler Cat Part No.K-12925IN-CP

S&F stainless steel of AE SI-316 grade tubular towel ring including a pair of CP brass bracket complete all as specified and directed. Make:- Cera Cat Part No.F5002105 / Kerovit Cat Part No KA670005 / Grohe Cat Part No.40365000 / Kohler Cat Part No.K5631IN-CP

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm, complete all as specified and directed..

S&F in repairs fancy type sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long, complete all as specified and directed. Make- Cera model No.F-5005301 / Asian Paints Cat Part No AC107 /Kerovit Cat Part No :- KA920005

S&F fancy type glass corner 300 mm radius of 10 mm thick toughened glass with CP railing fixed with fancy type screws complete all as specified and directed. Make- Jaquar Modeel- ACN-1173, Cera Model No F505101 / Kerovit Cat Part No KA990014

S&F in repairs PVC Corner set of three of size (12x12 inch, 9x9 inch & 6x6 inch) with railing, complete all as specified and directed.

S&F brass CP Hand Shower with 15 mm dia, 1.2 Meter Long flexible tube and wall hook, screwed for iron pipe fancy type long body, complete all as specified and directed. Make- Cera Cat Part No :-F7030308AB /Kerovit Cat Part No.KA520008 / Grohe Cat Part No.28756000/ Kohler Cat Part No.K-98445IN-CP

S&F in repair fancy type 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified and directed. Make- Cera Cat Part No. F2002461 /Kerovit Cat Part No.KB1211026 / Grohe Cat Part No.31831001 (Costa L) / Kohler Cat Part No.K-371161IN-4-CP

S&F low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls complete all as specified and directed.

S&F in repairs stainless steel Curtain Rod 25 mm dia, 1.18mm thickness of approved quality with two number decorative design 3 mm thick brackets fixed in brick/concrete wall and same finished knobs on each end of curtain rod complete all as specified and directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down AC/PVC rain water pipe, soil/waste/vent pipe of any size with fittings etc complete all as specified and directed.

S&F PVC (SWR) 110 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall complete all as specified and directed.

S&F in repairs PVC (SWR) 75 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall complete all as specified and directed.

S&F spun iron soil, waste and vent pipe, 75mm bore, in any length with or without ear with cement joint fixed to walls complete all as specified and directed.

M&L in repairs 75 mm dia PVC (SWR) multi floor trap with grating including jointing to waste pipe with solvent cement and fixed in plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F 100mm bore PVC (SWR) bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and directed.

S&F 80 mm bore CI bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and directed.

S&F PVC (SWR) 75 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and directed.

S&F PVC (SWR) 100 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and directed.

S&F in repairs PVC (SWR) 100 mm bore 'Y' Junction piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore bends complete all as specified and directed.

S&F in repairs PVC (SWR) 80 mm bore Cowl complete all as specified and directed.

S&F powder coated aluminium anodised frame for doors windows, ventilators and kitchen cupboards frame of size 100x44mm and 2mm thickness with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. (minimum thickness of powder coating 50 micron and weight of aluminum section shall be not less than 1.12 Kg/RM).

S&F stainless steel glossy finish hat peg set of five tier with necessary fitting, complete all as specifed and directed.

M&L for stainless steel floor trap of size 100x100mm, Anti cock roach proof Trap complete all as specified and directed.

S&F aluminium power coated (colour) section as in kitchen cabinet/ cupboard shelf incl hanging self for clothes with aluminium clip/strips, pvc beadings fixed with adhesive on edging window,ventilator,glazed with aluminium shutter(medium weght) of suitable size, one or more rebate,cut to jointed together with cadmium plated steel screws including rubber bending or gasket for aluminium sections for fixing glass/Xpm jalli and necessary fittingd,screws, plugs for fixing screws, etc complete all as specified and directed. (Aluminium section shall be of make Jindal/Hindalco/Indalco). Note : Weight of aluminium section shall not less than 0.55 Kg/RM and will be measured and rubber cost beading will be covered in the rate aluminium.

S&F powder coated aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality) for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and including 5.50 mm thick figured glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clipsa, frame made with aluminium section as appended below- (i) Window frame :68.4x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed in aluminium window or along with F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such as aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

M&L for 6 mm thick bakelite sheet prelaminated both side with decorative choice lamination work complete all as specified and directed.

M&L for stainless steel (AISI 304 Grade ) Non magnetic multilayer nikle chrome plated for multipurpose utensil container including frame work telescopic channels, handles etc as reqd and complete all as specified and as directed utensil sample, design and pattern of each basket to be approved by GE the following size in each kitchen (A) plain basket (03 nos of size 510x470x100mm or 520x485x100mm or 530x505x150mm slace godrej code 6126 Baan code LKY2PB 2014 -Evershine size 520x485x90mm (b) Multisize plate basket-02 nos of size 510x470x150mm or 520x485x150mm or 436x500x200mm (Clear depth 500mm) Make Silk Elnora BAAN code LKY-3CS214- Ever shine size 520x485x90mm approved by GE

(c) Cutlery Basket, with Perforated bottom and side of compacted -slots for holding cutlery- 02 Nos of size 510x470x100mm or 520x485x100mm or 144x468x50 (Clear depth of 500mm) Make Silk Elenora (Asian Paint) code 600, size 530x505x100mm (Godrej Product code 6134 BAAN Code LKY2PC214/Ever shine size 520x485x95mm (d) Plain basket of size 510x470x200mm or 520x485x200mm or 486x500x200mm 02 Nos make Silk Elenora (Asian Paint) code 600, size 53x505x200mm- Godrej product code 6128 BAAN code LKY 2PB218- Evershine size 520x485x180mm (e) pull out with 2 basket each of size 150x485x80mm or 100x485x80mm 01 Nos make Sleek Elenora (Asian Paint ) code 250 size 180x500x590mm / Godrej product code 6141 baan code LKYNS2SP6/Ever shine size 610x485x90mm (f) dust bin as reqd 01 Nos Make 200 series of Hettich

S&F mild steel framed work such as grills grating etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars, barrel iron doors ladders framed balusters walk ways railing frame work of water tanks and similar work confirming to Fe -290 Gde-E-165 complete all as specified and directed.

S&F sheet glass 5.5 mm thick ordinary quality and glazing with oil putty in square exc 0.5 Sqm each pane complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 (1979) grade St.-240 complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based (manglore pattern roof tiles) steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specifed and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement and including dismantling of existing MS/RCC railing complete all as specified and directed.

S&F Stack clamps for 75 mm dia pipe made out of 50x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, complete all as specifed and directed.

S&F Stack clamps for 110 mm dia pipe made out of 50x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, complete all as specifed and directed.

S&F 3.15mm dia magic eye for looking outside from main door for safety purpose, complete all as specifed and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in leveling course in 25 mm average thickness under floors and finish the surface even & fair of concrete complete all as specified and directed.

S&F computerized reflective letters / building nos on ACP sheet of size 45mmx45mm and fixed with 04 nos rawl plug & SS screws etc on wall in front of building, complete all as specifed and directed.

M&L for Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out, in soft/loose soil complete all as specified and directed.

Dismantling of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) complete all as specified and directed.

M&L for 75mm thick plain cement concrete1:4:8 type D-2 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for machine pressed cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS-15658-2006 of 80 mm thickness, M-40 grade, fixed with grey cement & pigment of approved design and pattern laid over & including 25 mm thick sand cushioning layer and filling the joints with sand, complete all as specified and directed.

M&L for pre-cast PCC 1:2:4 type B-1 (using 20 mm grade stone aggregate) kerb stone outer coloured surface, machine pressed factory made of size 300mm long 150mm wide and 300mm deep, set & jointed in cement mortar 1:4, complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in benching, kerb etc, weathering slightly rounded or chamfered angle and throating, complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement and no pigment, set, jointed and pointed in neat cement slurry over & including 15 mm thick screed bed in cement mortar 1:6 as in floors, path etc., complete all as specified and directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out, in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Hard and dense soil complete all as specified and directed.

Removing excavated Soil material n.exc. 50 mtr and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) in foundations filling and mass concrete complete all as specified and directed.

M&L for concrete bed to drain 150 mm bore NP-2 pipe, in plain Cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and jointes complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping /benching including necessary form work and finishing all exposed surfaces of concrete complete all as specified and directed.

M&L for brick work using kiln burnt brick with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4, complete all as specified and directed.

M&L for brickwork with kiln burnt sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1: 4, complete all as specified and directed.

M&L for rendering 15mm thick fair faces of brick work or on concrete surfaces in cement mortar 1:4 mixed with WPC as per manufacturer's instruction, finished the surface even and smooth wihtout using extra cement, complete all as specified and directed. (Note:- WPC will be measured & paid separately)

M&L for rendering 15mm thick fair faces of brick work or on concrete surfaces in cement mortar 1:3 mixed with WPC as per manufacturer's instruction, finished the surface even and smooth wihtout using extra cement, complete all as specified and directed. (Note:- WPC will be measured & paid separately)

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains internal dia of 150 mm bore NP-2 pipes, making good to pipe and rendering, cutting out existing benching for forming branch channel (1/2 round or 3/4 section) in plain cement concrete (1:2:4) type B-1 using 20 mm thick stone aggregates smooth finished, and reforming benching complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B-0 (12.5mm graded stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and setting in cement mortar 1:4 and to match for fixing of SFRC covers heavy duty HD-20 grade designation) etc complete all as specified and directed. (Note:- TMT bars and SFRC covers shall be measured & paid separately under respective item)

S&F TMT bars 8 mm dia upto 10 mm dia, cut to length, bent to shape required,including cranking and binding with mild steel wire (annealed) not less than 0.9mm dia. complete all as specified and directed.

S&F SFRC (Steel Fibre Reinforced Concrete) cover with frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to IS-12592, total weight of cover and frame to each shall not be less than 182 Kg, fixed in cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate), complete all as specified and directed.

S&F orange colour safety foot rests minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23mmx 25mm and overall minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2 mm tread on top surface by ribbing or chequerering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to withstand the bend test and chemical resistance test as per specifications and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm blocks of plain cement concrete 1:3:6 type C-1 (using 20 mm thick stone aggregate), complete all as specified and directed.

M&L for providing 50 mm thick plain cement concrete 1:4:8 type D-2 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in benching, coping etc. including necessary form work, weathering slightly rounded or chamfered angles and throating, complete all as specified and directed.

Dismantling fencing wire mesh, any type, complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground, complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum in soft/loose soil and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) in foundations filling and mass concrete complete all as specified and directed.

S&F mild steel angle iron or flat iron as in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F mild steel round bars 10mm dia Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde - E-165), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F mild steel screw bolts (machine made) of neck diameter 10 to 50mm long with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed.

Supply only chain link fencing, galvanized mild steel of mesh 50mm x 50mm size and diameter of wire 4 mm, complete all as specified and directed.

Fixing only chain link fencing, including line wires, any mesh size, mild steel to any type of standards, rails, straining bolts etc complete all as specified and directed.

Preparation of new steel surfaces and applying two coats of black bituminuous paint on embedded portion of angle iron posts/struts etc., complete all as specified and directed.

M&L for framed work as in doors or ornamental and intricate design gates of angle or other section with gusset plate or rails ,baraces ,etc.compltete drill for fixing steel sheeting or other covering door etc to be prepared for hanging or sliding with and including with hanging and higes (excluding steel sheeting or other covering ,running rails and guides.) and hanging also fastening complete conforming to FE -410 GDE E 250 complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint (1st quality) over a coat of red oxide primer on newly steel surface of any description, including prepartion of steel surfaces, complete all as specified and directed.

M&L for brick work with kiln burnt brick with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for rendering 15mm thick fair faces of brick work or on concrete surfaces in cement mortar 1:4 , finished the surface even and smooth wihtout using extra cement, complete all as specified and directed.

M&L for providing cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in benching, coping etc. including necessary form work, weathering slightly rounded or chamfered angles and throating, complete all as specified and directed.

Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified and directed.

Taking down carefully unserviceable main switch DBs incl MCCBs and MCBs of any description of an size in any position complete all as specified and directed.

Taking down submain wiring including all accessories complete all as specified and directed.

M&L for concealed type point wiring with single core 1.5 Sqmm (Nominal area) PVC insulated, unsheathed, multi-stranded copper conductor FRLS cable (1100 volts grade) , ISI marked, drawn in and including rigid PVC conduits 20 mm dia with all fittings and accessories alongwith PVC insulated cable with single core copper conductor 1.5 Sqmm as earth continuity conductor including fixing of 2mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers incl. making good the disturbed surfaces complete all as below:-

(a) One light / fan/ exhaust fan point controlled by one switch.

(b) One 5 pin 5 Amp switch socket out let point on an independent board.

(c) One 5 pin 5 Amp socket out let point controlled by one switch on same board.

(d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent

(e) One light point controlled by two, two way switch on Independent board.

All as per item 210 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded complete all as specified and directed.

M&L for concealed type point wiring with single core 1.5 Sqmm (Nominal area) PVC insulated, unsheathed, multi-stranded copper conductor FRLS cable (1100 volts grade) , ISI marked, drawn in and including rigid PVC conduits 20 mm dia with all fittings and accessories alongwith PVC insulated cable with single core copper conductor 1.5 Sqmm as earth continuity conductor including fixing of sunken terminal box suitable for modular modules and cover plate duly flushed to wall including making good the disturbed surfaces for the following the points complete all as specified & directed: -

(a) One light / fan/ exhaust fan point controlled by one switch.

(b) One 5 pin 5 Amp switch socket out let point on an independent board.

(c) One 5 pin 5 Amp socket out let point controlled by one switch on same board.

(d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent

(e) One light point controlled by two, two way switch on Independent board.

All as per item 217 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded complete all as specified and directed.

S&F modular Switch one way 10 Amps, 1 Module, complete all as specified and directed.

S&F modular Switch one way 16 Amps, 1 Module, complete all as specified and directed.

S&F modular Switch two way, 10 Amps, 1 Module, complete all as specified and directed.

S&F modular bell push one way, 6 Amps, 1 Module, complete all as specified and directed.

S&F modular socket outlet 2/3 pin, 6 Amps, combined 2 Module, complete all as specified and directed.

S&F modular socket outlet 2/3 pin, 6/16 Amps, combined 2 Module, complete all as specified and directed.

S&F modular fan regulator step up type, 120 watt, 2 Module, complete all as specified and directed.

S&F switch piano flush type 5 Amp single pole one way complete all as specified and directed.

S&F socket out let 2 in 1 flush type 5 Amp 5 Pin complete all as specified and directed.

S&F switch piano flush type 15/16 Amp single pole one way complete all as specified and directed.

S&F socket out let 6 Pin 2 in 1, 5/15 Amp flush type 240 Volt complete all as specified and directed.

S&F Switch piano flush type 5/15 Amps, single pole, two way, complete all as specified and directed.

S&F bell push flush type 5 Amp complete all as specified and directed.

S&F bell ding dong musical ,AC, 230 Volt, single pole complete all as specified and directed.

Fixing only serviceable switch piano flush type 5 Amp single pole one way complete all as specified and directed.

Fixing only serviceable socket out let 2 in 1 flush type 5 Amp 5 Pin complete all as specified and directed.

S&F ceiling rose PVC / Poly carbonate, Isolated body, three terminal AC 230 volts complete all as specified and directed.

Supply and fix fan regulator 150 watts electronic flush socket type with five stepped range hum free complete all as specified and directed.

S&F lamp holder, PVC / Poly carbonate, insulated body with back plate batten/angle type for batten fittings complete all as specified and directed.

S&F LED mirror light fitting of 1 x 10 watt T-5 lamp type with electronic ballast of suitable capacity, clear acrylic cover including mounting on wall complete all as specified and directed.

S&F indoor decorative LED City-3 light fitting suitable for & including single 12 Watt LED lamp with polycarbonate body with upper globe complete all as specified and directed.

Supply and fixing surface mounting LED light fitting AL extruded T-5 batten , 20 Watt, 4 feet including connection with 23/0.0076 three core PVC flexible cable etc complete all as specified and directed.

Supply & Fix LED lamp 12 Watt, 230 V , AC integrated circuit complete all as specified and directed.

Supply & Fixing security light fitting, LED type, 20 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed.

Fixing only LED light fitting of any description LED batten, 20 Watt, 4 feet including connection with 3 core 23/.0076 three core PVC insulated copper conductor flexible cable, complete all as specified and directed.

Supply and Fixing surface mounting LED slim square down lighter made of PDC aluminium with high efficent LEDs and glare free opal diffuser, IP-20, 12 watt, 220 volts AC complete with driver holders LED lamp suitable for roof ceiling including connection with 3 core 23/.0076 three core PVC insulated copper conductor flexible cable, complete all as specified and directed.

M&L for sub main wiring with two run, single core 6.0 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. (Note :- Two runs of 6.0 sqmm (FRLS) and one run of 6.0 sqmm (FRLS) copper conductor shall be measured as one unit length.)

M&L for sub main wiring with two run, single core 4.0 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 4.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. (Note :- Two runs of 4.0 sqmm (FRLS) and one run of 4.0 sqmm (FRLS) copper conductor shall be measured as one unit length.)

M&L for sub main wiring with four run, single core 10 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 10 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly, complete all as specified and directed. (Note :- Four runs of 10 sqmm (FRLS) and one run of 10 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Taking down carefully ceiling fan and deposit to E/M store yard, complete all as specified and directed.

Taking down carefully exhaust fan with louvers from existing site and carry out for servicing by opening motor, romoving / clening the dust from body, oil greasing complete including one coat of smoke grey synthetic enamel paint, cutting hole into wall of appropriate size for fixing exhaust fan with necessary arrangement such as grouting threaded bolts/nuts & washers and making good the disturbed surfaces of wall and provision of new single core twin twisted cable from ceiling rose to exhaust fan connector, complete all as specified and directed.

Taking down carefully Geysers and deposit to E/M store yard, complete all as specified and directed.

Supply and fixing ceiling fan with blades, down rod and accessories, 230 volts, 1200 mm sweep, minimum air delivery 210 CFM with service value 6.00 BEE 5 star rated ith brushless direct current motor (BLDC) including connection with flat 3 core copper wire 1.5 sqmm from celing rose to connector, complete all as specified and directed.

Supply, installing, testing and commissioning exhaust fans (PVC body) 300 mm sweep, 230 volt, AC, 50 Hz single phase with louvers complete and including cutting of wall of appropriate size for fixing of exhaust fan and making good complete all as specified and directed.

Supply, installing, testing and commissioning electric water heater(Geyser) steel body with copper inner tank and heating element of 2 KW capacity 25 Ltrs capacity, BEE 5 star rated, AC, 50 Hz single phase complete and including connecting up with flexible three core copper conductor etc complete all as specified and directed.

M&L point wiring for inverter point with provision of 5 Amp switch socket combination with single core wire suitable for inverter wiring in all board for light and fan point including all bedrooms, hall, kitchen toilet etc complete all as specified and directed.

S&F TV socket for cable connection with concealed modular metal box with white modular cover with all accessories complete all as specified and directed.

S&F MCB SPN 40 Amp 240 volt, 'B' curve, breaking capacity 10 KA, complete all as specified and directed.

S&F MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed.

S&F MCB TPN 40 Amp 415 volt, 'B' curve, breaking capacity 10 KA, complete all as specified and directed.

Supply and fix flush sheet metal enclosure SPN DB 8 way, 240 volts, with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete including taking down old unserviceable complete all as specified and directed.

Supply and fix flush sheet metal enclosure, TPN DB 8 way, 415 volts, with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete including taking down old unserviceable complete all as specified and directed.

Supply and fix single pole & neutral enclosure, SPN with a two pin earth plug and socket including 01 nos single pole MCB 20 Amps, complete all as specified and directed.

Supply & installation LT Meter box wall mounted made out of 2 mm thick CRCA sheet indoor type totally enclosed weather, dust & vermin proof with front openable door with locking arrangement mounted on 04 nos mild steel flat iron 40x6 mm, 150 mm long of size not less than 900x900x250mm and maximum size suitable for fixing under metioned MCCBs, Pre paid meters, Multifunction meters 415 Volts 3 Phase and neutral, 4 wire, 50 Hz AC supply system having bus bar chamber with insulated electrolyted aluminium bus bars TPN of capacity 100 Amps rating insulated, bus bar mounted on DMC insulators with bus bar chamber, front opening type with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 6 sqmm complete. All steel metal works including frame shall be with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens gray RAL-7035 shade. The scope of work also comprising of the following and size of panel suitable to fixing all below materials with required space as per IE rules:- .(a) BUS BAR CHAMBER :- i) 100 Amps TPN main aluminium bus bars with color coded heat shrinkable sleeve and shall be mounted on non hygroscopic , non combustible, track resistant high strength DMC material interconnection of all incomings & outgoings. ii) Red, Yellow Blue Phase indicating lights LED Type 220 V AC-1 Set (Set of Three) INCOMING SUPPLY:- i) MCCB 40 Amps 10 KA, 4 Pole, 415 Volts, 50Hz- 01 No. OUT GOING SUPPLY:- i) MCB SPN 25 Amps 10 KA, - 04 Nos.

Supply & installation LT Meter box wall mounted made out of 2 mm thick CRCA sheet indoor type totally enclosed weather, dust & vermin proof with front openable door with locking arrangement mounted on 04 nos mild steel flat iron 40x6 mm, 150 mm long of size not less than 900x900x250mm and maximum size suitable for fixing under metioned MCCBs, Pre paid meters, Multifunction meters 415 Volts 3 Phase and neutral, 4 wire, 50 Hz AC supply system having bus bar chamber with insulated electrolyted aluminium bus bars TPN of capacity 100 Amps rating insulated, bus bar mounted on DMC insulators with bus bar chamber, front opening type with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 10 sqmm complete. All steel metal works including frame shall be with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens gray RAL-7035 shade. The scope of work also comprising of the following and size of panel suitable to fixing all below materials with required space as per IE rules:- .(a) BUS BAR CHAMBER :- i) 100 Amps TPN main aluminium bus bars with color coded heat shrinkable sleeve and shall be mounted on non hygroscopic , non combustible, track resistant high strength DMC material interconnection of all incomings & outgoings. ii) Red, Yellow Blue Phase indicating lights LED Type 220 V AC-1 Set (Set of Three) INCOMING SUPPLY:- i) MCCB 100 Amps 16 KA, 4 Pole, 415 Volts, 50Hz- 01 No. OUT GOING SUPPLY:- i) MCB TPN 63 Amps 10 KA, - 04 Nos.

M&L for earthing complete including taking out old unserviceable and replace with galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe 'light grade' as water pipe from earth chamber and including excavation and earth work, PCC 1:3:6 type C1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm, 4 core, complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm, 3.5 core, complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 sqmm, 3.5 core, complete all as specified and directed.

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed.

Material and labour for Brick protection with sub class 'B' bricks old size, laid dry, flat over cable, perpendicular across the cable in trenches complete all as specified and directed.

S&F GI pipe 80mm bore light grade galvanised with all fittings and fixed complete for road crossing /on wall/floor and crossing culvert or laid in floor complete all as specified and directed.

S&F GI pipe 40mm bore light grade galvanised with all fittings and fixed complete for road crossing /on wall/floor and crossing culvert or laid in floor complete all as specified and directed.

Taking down of old aluminium conductor / hanging services mains of any description / size from LT poles, panel including dismantling insulators, complete all as specified and directed.

Dismantling stay assembly complete all as specified and directed.

Dismantling of cross arms of mild steel channels or angle section etc. including necessary T&P required at site complete all as specified & directed.

Taking down carefully old street light fitting from pole of any capacity and any description with GI pipe mounting bracket of any size and clamps etc and refixing the same including painting on steel poles and bracket & clamps with two coat of aluminium paint and colour strips on poles as per existing pattern with synthetic enamel paint, including connection with flexible 3 core copper cable 1.5 sqmm from pole box to light fitting connector, complete all as specified and directed.

S&F loop in and loop out box of size 20x15x15 cm made of 1.6 mm thick PVC sheet weather proof, dust and vermin proof with hinged door of locking arrangements and slanting cover on top with provision of aluminium busbar of size 25x2 mm 02 Nos fixed on insulators and MCB capacity 6 Amps single pole 'C' series complete fixed on pole with and including suitable size MS flat iron clamps, nuts, bolts and washers, etc complete all as specified and directed.

Supply, installation, testing and commissioning of LT feeder pillar outdoor type of size 2000 x 1500 x 600 mm CPRI certified factory made cubical type weather and vermin proof fixed on and including ventilation and louvers arrangement PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in foundation of required / suitable size and as directed at site with angle iron frame of size 70 x 70 x 6 mm, 3 phase, 4 wire, 415 volts 50 Hz fabricated out of 3.15 mm thick CRCA sheet steel including duly powder coated painted and keeping adequate working space inside of the box (outer width of the box not less than 45 cm and gap between bus bar not less than one inch) and double door handle including locking arrangement with 1 nos pad lock of 65 mm long as directed before manufacturing the panel including dismantling / disconnection of old rusted LT panels with accessories. The drawing of the feeder pillar box will be approved by Engr-in-Charge and same have the following electric controls :-

Insulated epoxy coated high conductivity aluminum bus bar 630 Amps (Size 60 mm x 6 mm thick) for phase and neutral complete all as specified and directed.

(A) Incoming:-MCCB 400 Amp 50 KA, 4 pole, 415 volts 50 Hz adjustable thermal & magnetic setting with OL and OC position- 01 No

(B) Outgoing:- (a) MCCB 100 Amp 25 KA, 4 pole, 415 volts 50 Hz adj thermal & magnetic setting (As outgoing) - 05 Nos (b) MCCB 63 Amp 16 KA, 4 pole, 415 volts 50 Hz adj thermal & magnetic setting (As outgoing) - 02 Nos

LED indicating lamp assembly R, Y, B phase - 06 Set

M&L for construction of platform for mounting Panel with 150mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in foundation mass concrete, brick work in CM 1:6 with sub class 'B' bricks old size, rendering 15mm thick in CM 1:4 on exposed surfaces, 100mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) padding on top for grouting bolts etc for panel, complete all as specified and directed. (Note:- The height of platform shall be 45 cm from the existing nearest road level.

(a) M&L for fabrication of MS busbar chamber of nominal dimension 900 mm x 600 mm x 400 mm duly provided with aluminium busbar of size 50 mm x 6 mm fixed on porcelain insulators TPN type outdoor weather / vermin proof with both way opening duly provided with neoprene rubber gasket along the doors openings pedestal type duly painted powder coated on CRCA sheet encloser 3.15 mm thick with 01 Nos Incomer MCCB 100 Amps 3 pole, 16 KA including making connection/ thimbles etc complete all as specified and directed. Make : Havells / Schneider / Gaurav Energen

(b) M&L for construction of platform for busbar chamber with 150mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in foundation mass concrete, brick work in CM 1:6 with sub class 'B' bricks old size, rendering 15mm thick in CM 1:4 on exposed surfaces, 100mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) padding on top for grouting bolts etc for panel, complete all as specified and directed. (Note:- The height of platform shall be 45 cm from the existing nearest road level)

(b) M&L for earthing complete with galvanised or steel earth plate electrode of size 60cm x60cmx6mm thick burried directly in ground vertically ( to a depth not less than 2.25mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI strip 32x 6 mm size with nuts, bolts , check nuts , washers in protection GI pipe 40 mm bore light grade and connecting to earth plate to test point, main switch board, earth plate surrounded by packed layers of charcoal dust and common salt 15cm thick all around, top & bottom, GI pipe 20mm bore of GI medium grade for watering with funnel and wire mesh and testing on completion including PCC chamber concrete 1:3:6 type C-2 and RCC cover 75mm thick with MS TMT bar 8mm dia @ 150mm c/c both ways in cement concrete 1:2:4 type B-1 all as shown in electrical plate in No 3 of SSR(Pt-I) 2009 complete all as specified and dirfected by Engineer-in-charge. Note : (i) If the desired earth resistance is not found within permissible limit, shall be redone by contractor at no extra cost. (ii) Cost of GI strip 32 x 6mm and 40 mm dia GI pipe light grade upto 7.5 m is included in the rate quoted for this item.

Taking up/down old GI tubing 20/25 mm bore, complete all as specified and directed.

Supply and laying in trenches GI tubing 25 mm bore, medium grade ISI marked with all fittings (ie union, socket, elbow etc) for pipe complete all as specified and directed.

Supply and laying in trenches GI tubing 20 mm bore, medium grade ISI marked with all fittings (ie union, socket, elbow etc) for pipe complete all as specified and directed.

S&F 25 mm dia gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F 20 mm dia gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Note : Tenderers may note that amount of credit Rs1495721.80 will be deducted from the total amount arrived, at the time of Acceptance of contract.

M/s J P Bhatia

M/s Arihant Builders

Sudhir Sharma Associates

Global Enterprises

City Promoter and Buildwell Pvt. Ltd.

J.D.Builders

SAWHNEY BUILDWELL LLP