PROVN OF COVERD VERNDAH WITH GALVALUME SHEET AT TRG HALL SPECIAL REPAIR TO BLDG NO T19 OF ASRI GUARD ROOM STN GATE AND PROVN OF TOILET BLOCK NEAR SHOPPING COMPLEX AT 20 CMP SRC AT RAMGARH CANTT

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete and removing rubbish off from the premises complete all as specified and directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:4) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

M&L for Vetrified light shed coloured floor tiles 10 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc set & jointed in neat cement slurry and pointed in cloured cement to match the shade of tiles over & including 15 mm thick screed bed in cement mortar (1:6) etc complete all as specified & directed.

M & L glazed ceramic coloured tiles of size 375 mm x 250 mm x7mm/450 mm x 300 mm x7 mm thick ,as in dado/skirting etc ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles including 10 mm thick rendering in cement plaster in CM (1:4) complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails/screws complete all as specified and directed.

S & F for providing aluminium snap grid frame work for false ceiling system with size 605 mm x 605 mm, consisting of main runner of size 36.5 mm x 25 mm x 1.4 mm (weight not less than @ 0.24 Kg/Rm) and cross Tee of size 23.5 mm x 36.4 mm x 1.4 mm (weight not less than @ 0.191 Kg/Rm). The snap grid shall be supported at end all along the wall with aluminium anodised angle of size 40 mm X 25 mm X 2 mm (weight not less than @ 0.36 Kg/Rm).The snap grid shall be fixed to ceiling supporting hangers consisting of 2 mm dia mild steel wire /GI wire, J-bolts ,nuts and washers as per manufacturer's instructions and complete all as specified and directed by Engr-in-Charge.

M & L for 4.0mm thick Non asbestos fibre cement building boards fixed in ceiling flat or sloping fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed by Engr-in-Charge.

S & F in repair for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Hacking out old boken glass(any thickness, size, quality or description) from wooden frames/steel frames or stone , concrete or brick surrounds, glazed with oil putty or fixed with beads removal from site complete all as specified and directed

M & L for 3mm thick plain sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engr-in-Charge .

M&L for prepartion of old painted of wooden surface of any description , not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint on old wooden painted surface complete all as specified & directed.

M&L for prepartion of old painted of steel surface of any description , not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint on old steel painted surface complete all as specified & directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with preparation of plastered surfaces and apply two coats of distemper oil emulsion (OBD) over a coat of primer and a layer of putty (not less than 1.5 mm thick )complete all as specified and directed.

M & L for preparation of old surface of wall and applying one coat of cement base paint on wall including necessary scaffolding complete all as specified & as directed.

S & F in repair vitreous China wash basin, any colour, flat back size 550 mm X 400 mm including 32mm brass chromium plated waste coupling , 32 mm bore PVC waste pipe, chromium plated Grating including cutting for & pinning in ends of bracket or errecting bracket ,fixing of pillar tap & PCC 1:2:4 ,type B-1(using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed. Note : Pillar tap as supply only will be measured & paid seperately under respective item of BOQ.

Supply only pillar taps fancy type, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed.

S & F in repair vitreous China half stall type (back to corner )urinals with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)(back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe etc.complete all as specified and as directed

S & F vitreous China half stall type (back to corner )urinals with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)(back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe etc.complete all as specified and as directed

S&F in repair vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device complete all as specified and directed. Note : Plastic seat cover shall be measured separately as Supply only as considered under respective items.

Supply only plastic water closet seat closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S & F in repair PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S & F PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S&F in repair for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair bib taps , cast copper alloy with capstan head or butter fly handle,chromium plated fancy type screwed down with high pressure screwed for iron pipe and fixed 15 mm bore complete all as specified & directed.

S&F in repair stop valve 15mm bore chromium plated ,fancy type cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall etc complete all as specified and directed.

S&F in repair brass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flanges fixed with and including chromium plated brass screw & wooden /plastic cleats complete set all as specified and directed.

S&F PTMT towel rail 450 mm long between flanges fixed with and including chromium plated brass screw & wooden /plastic cleats complete set all as specified and directed.

S&F in repair double arm wall mounted reversible plain /magnifying pivotal mirror complete all as specified and directed.Make: Jquar cat part No. CAN 1193 N (Continental Series) or equivalent in MARC/Parko

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed

S & F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed

S & F in repair 40 mm dia bore waste coupling of CP brass (half or full threaded )minimum weight 45 gms suitable discharge pipe complete all as specified and directed by Engineer-in- Charge.

S & F 40 mm dia bore waste coupling of CP brass (half or full threaded )minimum weight 45 gms suitable discharge pipe complete all as specified and directed by Engineer-in- Charge.

S & F in repair 32 mm dia bore waste pipe fixed to wash hand basin complete all as specified and directed by Engineer-In- Charge.

S & F 32 mm dia bore waste pipe fixed to wash hand basin complete all as specified and directed by Engineer-In- Charge.

S & F in repair Grating doom 100mm dia of PTMT (minimum weight 25gms) complete all as specified and directed by Engineer-in- Charge.

S & F in repair Grating doom 125 mm dia with waste hole of PTMT. (minimum weight 40gms) complete all as specified and directed by Engineer-in- Charge.

Repair & easining of aluminium window/door and refixing on the same position including all necessary asseccories complete all as specified and directed.

Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out off MOD land etc complete all as specified and directed.

Dismantling old Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed

S & F fo Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust,etc.complete with & including brushing neat cement slurry (@ 3 Kg of cement per Sqm) for bonding of old concrete surface to new concrete, complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18mm -20 mm thick of size not less than 575 mm X 575 mm, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing & polishing over & including 20 mm thick screed bed in CM (1:4) complete all as specifed & directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Add to (or deduct from) above item No. 45 for every 3cm or part there of above or below 15 cm average depth complete all as specified and directed.

Excavation in trenches in soft & loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes,foundations,laying of cable, shafts, well, cesspits, manholes etc. complete all as specified and directed.

Excavation in post holes (or similar holes) not exceeding 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick as in soft / loose soil including watering & removing surplus soil material to a distance not exceeding 50 mtr & making good surface complete all as specified & directed.

M&L for plain cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in foundations for tubular post ,filling & mass concrete etc complete all as specified and directed.

S&F steel work in tubular trusses /tubular post (square/ rectangular /circular) steel tubular sections including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161 1979 Grade St-240 complete all as specified and directed. Note: Drawing & design shall be approved by GE.

Returning, filling in including spreading, leveling, watering and well ramming in layers of not exceeding 25 cm thick after the cables & pipes etc. are laid, jointed & tested and foundations complete all as specified and directed by Engineer-in-Charge.

Removal of surplus excavated spoil exceeding 250 Mtr but not exceeding 500 Mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring, foundations,filling & mass concrete for fencing posts, foundation of pole ,struts & stay assembly etc complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in foundation including rafts, footings,plinth beams, and mass concrete etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use & waste of form work to sides of concrete foundation, base of coloumn ,rafts,footings, plinth beams, and plinth beam and similar work for rough finished flat surfaces of concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in columns,pillars,piers,popst and struts etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides of columns,pillars,piers,post and struts for rough finished surface of concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in lintels beam, floor/roof Beams, cantilevers, bressummers, etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in chajja etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides of soffit of chajja,chullah hoods,troughs & similar items etc including for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to sides and soffit of lintel Beam,floor/roof Beams, etc for rough finished surface of concrete complete all as specified and directed.

M&L for half brick thick Brick work using fly ash bricks old size , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 etc complete all as specified & directed.

M&L for Brick work using fly ash bricks old size , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

M&L for mild steel TMT bars 10mm dia and over grade Fe-500, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for mild steel TMT bars 08 mm dia and over grade Fe -500 , as in reinforcement ,cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for mild steel TMT bars 08 mm dia and over grade Fe -500 , as in stirrups, spacers & binders ,cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M & L for 40 mm thick damp proof course PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate )mixed with integral water proofing compound (as per manufacturer’s instructions) or @ 3% by weight of cement)conforming to IS: 2645 including covered with 100 micron thick polythene film complete all as specified & directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

Supply only water proofing compound complete all as specified and directed.

M&L for rendering 15 mm thick on brick masonry/concrete surface etc in CM (1:4) surface finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on brick masonry/concrete surface etc in CM (1:6) surface finished even & smooth using extra cement complete all as specified and directed.

M&L for preparation of newly plaster surface of wall and applying two coats of cement base paint over a coat of alkali primer including necessary scaffolding complete all as specified & as directed.

M&L for preparation of newely plastered surfaces of wall and applying three coat of white wash on new wall surface complete all as specified & directed.

S&F roof trusses (framed), trussed, purlins, crane guntries, rail, fastening ,heavy bracket ,rafter,framing (beam, tee, angle, channel or flat sections) distance pieces, cleats including fabrication and fixing conforming to Fe-410-W(Gde E-250) quality-A complete all as specified & directed.

M&L for prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

M&L for hard core of broken stone or boulder gauge not exceeding 63mm deposited, spread & leveled in layers not exceeding 15cm thick, watered and rammed to a true surface etc complete all as specified& directed.

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushed stone aggregate ) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 grade and sand in the ratio 1:3 including necessary form work , complete all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to flooring/hard standing etc ,complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in kerb/benching/copings including weathering, slightly rounded or chamfered angle and throating including use & waste of necessary form work etc complete all as specified and directed

M&L for plain cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in floor/hardstanding etc surface finished even and smooth without using extra cement complete all as specified & directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engr-In-Charge .

S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as fixing in the frame at site as per specification and drawing including 3 Nos stainless steel butt hinges 100 mm long for each door, complete all as specified and as directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed.

S & F 100mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed .

S&F 150mm aluminium alloy handles, cast type, anodised complete all as specified & directed.

S &F powder coated aluminium work for doors, windows, ventilators shutters(fixed/sliding track two or three track) and partitions frames with extruded built up standard sections of approved make fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions with sealent with wall, i.e. at top, bottom and sides including cleat angle, C.P. brass/ stainless steel screws, all complete all as specified and directed.

S&F powder coating of any colour (thickness or powder coating not less than 50 micron) anodised , windows, ventilators shutters , fixed type without sash bar ,aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips rubber packing anodised aluminium, snap beading screws, powder coated aluminium fittings such as peg stays 150mm long (1No.),100mm long hinges type B-21 (2Nos), suitable handle(02 Nos.) in each door top rail guide rail etc. complete all as specified and directed.

S&F for powder coated aluminium grills size 4mmx4mm, 8mm thick and aperture not exeeding 50 mm X 75 mm width and including fixing with aluminium channel, 1 mm thick with steel screw and tint match for windows and ventilators etc. complete all as specified and as directed.

S&F 4 mm thick figured glass pin headed type in squares/ rectangular not exceeding 0.5 Sqm in each pane glazing with oil putty or aluminium frame/shutters with rubber neoprene beading complete etc all as specified & directed.

S&F rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in base of PVC tank etc including necessary form work complete all as specified and directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chasees for brick walls and making good the surfacein cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls /laid in trenches and ceiling or laid in floors including cutting chasees for brick walls and making good the surfacein cement mortar 1:3 complete all as specified & directed.

S & F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F stop valve/cock 15mm bore chromium plated with long shank fancy type cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall etc complete all as specified and directed.

Cutting chases, pinning in to in brick wall , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Cutting existing steel tubing for alterations or additions (Each cut measured) 15mm bore of pipes complete all as specified and directed.

S&F bib taps , cast copper alloy with capstan head or butter fly handle,chromium plated fancy type screwed down with high pressure screwed for iron pipe and fixed 15 mm bore complete all as specified & directed.

S & F vitreous China wash basin, any colour, flat back size 550 mm X 400mm including 32mm brass chromium plated waste coupling ,PVC 32 mm bore waste pipe, chromium plated Grating including bracket , fixing of pillar tap & PCC 1:2:4 ,type B-1 (using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed. Note : Pillar tap as supply only will be measured & paid seperately under respective item of BOQ.

M&L for 16 to 18 mm thick granite slab (or any type) table rubbed and pre mirror polished in steps,jambs,pillar,window cill,cooking platforms and like in cement mortar1:4, set & jointed in neat cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite ,over & including 15 mm thick rendering in cement mortar(1:4) etc complete all as specifed and as directed.

S&F WC squatting pan " Orissa Pattern" of size 580 mm X 440 mm white with integral foot rest including cast iron "P" or "S" trap, front or back inlet and making connection to trap & to flushing cistern complete including taking down existing pan & making good disturbed surface complete all as specified & directed.

S&F 75 mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches ,floor or in wall complete all as specified and directed.

S&F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches ,floor complete all as specified and directed.

S&F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F 110 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F in repair 75 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement with chromium plated grating with or without hole complete all as specified and directed.

Taking down carefully unserveciable/damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets ,light fittings etc) and removing material from site and making good to the disturbed surface to match with existing finish etc complete all as specified and directed.

M&L for point wiring for one light/fan/exhaust fan point/ bell /buzzer point controlled by one way switch with using with FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 1.5 Sq.mm nominal cross sectional area for phase & neutral and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steel sheet terminal box (normal & modular type) made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including PVC board with bakelite sheet 2.8 mm thick laminated cover make sheet for housing/fixing switches etc., including cutting holes for switches,sockets,regulators etc as per requirement including fixing with machine screw,washer etc complete all as specified and directed. Note: Proper colour coding to be adopted.

All as per item No .112 here-in-before but 3/5 pin socket outlet 5 Amp socket outlet on same board.with other switches

All as per item No. 112 here-in-before but for 3/5 pin, 5 Amp switch socket on independent board.

M & L Sub main wiring with two runs of single core 6.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 6.0 Sqmm PVC insulated unsheathed FRLSH multi stranded copper conductor cable for earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia/appropriate dia with accessories & fittings complete and making good disturbed surface wall including taking down existing sub main wiring complete all as specified and as directed. Note : - Two runs of 6.0 Sqmm cable and one run of earth wire 6.0 sqmm & conduit shall be measured as one unit length and extra length of cable required for connection to MCBs shall be deemed to be include in unit rate quoted by bidder.

S & F switch piano flush button single pole one way 5 Amp, complete all as specified and as directed.

S & F socket outlet 2 in 1, 3 pin, 5Amp, flush type, universal, complete all as specified and as directed.

S & F fan regulator electronic, step type hum free, socket type, suitable for ceiling fans of any capacity, pre wired 230 volts AC 50 HZ supply 100/120 Watt complete all as specified & as directed

S & F ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified & as directed

S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified.

M&L for point wiring with FRLSH PVC insulated PVC sheathed electric cable confirming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 2.50 Sq.mm nominal cross sectional area for phase & neutral & including non metallic rigid PVC conduit ISI marked medium grade not less than 25 mm dia with all conduit accessories in concealed wiring system & 2.50 Sq.mm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including pressed steel anodized sunken boxes 60 mm deep & 1.6 mm thick duly painted inside & anticorrosive outside with Bakelite hylem sheet 2.80 mm thick complete for one six pin switch socket outlet combination ,15 Amps & 3/5 pin socket point on independent board controlled by one ,one way switch complete all as specified and directed.

S & F Socket outlet 2 in 1, 3 pin, 5Amp and 15 Amp flush type, universal, complete all as specified.

S & F switch piano flush button single pole one way 15 Amp, complete all as specified and as directed.

S & F LED tube light fitting 1 x 20watt , 220 V, AC, surface and wall mounted LED batten PVC housing with polycarbonate diffuserand integrated electronic driver complete with all accessories ,driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge.

S & F in repair sheet metal enclosures powder coated for DBs when MCBs to used single pole and neutral (SPN) double door 240 volts, 12 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked) EARTH BAR & DIN RAIL confirm to IS:13032-1991 DB complete all as specified and as directed.

S & F in repair sheet metal enclosures powder coated for DBs when MCBs to used single pole and neutral (SPN) double door 240 volts, 4 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked) EARTH BAR & DIN RAIL confirm to IS:13032-1991 DB complete all as specified and as directed.

S&F in repair miniature circuit breaker (MCB) SP 6 to 32 Amps ('B' Series) having current rating 10 KA complete all as specifed and as directed .

S & F in repair miniature circuit breaker (MCB)(ISI marked) 415V, 10 KA 'B' Curve and current carrying capacity 40Amp, double pole in the MCB DB complete with connection testing and commissioning all as specified and as directed.

M&L ,for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts check nuts & washers of galvanised iron or steel, protected by GI pipe 15 mm bore (light grade) and watering pipe 20 mm bore GI pipe (light grade) and PCC of chamber and coping shall in 1:3:6 type C-1 (using 20 mm graded stone aggregate ) including excavation and earth work and removal of surplus soil and filling with black cotton soil upto ground level complete all as shown in electrical plate No 3 of SSR Pt-I, 2009 with CI cover 10mm thick of size 300x300mm with charcoal dust and common salt complete and earth lead connected to panel including testing including taking down existing earthing complete all as specified and directed. Note : Earth test result should not less than one ohm.

Dismantling house service brackets of any type complete all as specified and directed.

S & F in repair 40 mm bore GI tube, light grade with all fitting for cable protection including clamp ,nut,bolts & washer etc complete all as specified and as directed.

TS & F LED mirror type light fittings 1 x 9/10 watts with high out put diffuser 2 feet ,220 volt ,AC decorative type with driver holder & LED lamp & all other accessories duly pre wired and making connection with and including three core copper flexible wire from connector to ceiling rose not less than 1 mtr fixed on wall with plastic gutties complete all as specified & directed.

S & F LED bulb of capacity 15 watt , lumen out put (500)lm ,length 102 mm dia 56 mm , base cap B22 (ISI mark) complete all as specified and as directed by Engr-in-Charge.

S&F 1X9 W/1X10 W watt LED Bulkhead fitting with IP 65 environmental frendly, ultra modern, energy saving mounted decorative oval bulk head edge lit LED luminaire comprising of high brightness LED 230 Volts AC circuit complete all as specified and as directed.

S & F plastic body Exhaust fan of 150 mm sweep blade with louvers shutter , frame single phase ,240 V,50 Hz,900 RPM AC ,copper winding, including provision of hole, mounting frame, nut, bolts, washer, fasteners etc and connecting exhaust fan to ceiling rose including provision of three core flexible copper cable of size 1.5 sqmm not less than 0.5 mtr long for connection complete all as specified & directed.

S & F amp rating 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

S & F 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including4mm suspension wire, one twin core cable flat or circular ,size of conductor 6 Sqmm complete all as specified and as directed.

S & F building security lights with new generation energy saving & environment friendly long life versattle pressure dia cast aluminium IP-65 road luminarie with high power LED as light source & exclisively designed polycarbonate cover alongwith electronic driver type street light fitting 35 watt capacity LED including all accessories duly pre-wired,fixing on existing bracket with nut,bolt & washer etc as required at site for fixing of street light on pole/wall complete including taking down existing street light fitting any type complete all as specified & directed.

S & F in repair bracket made out of 40 mm dia GI pipe light grade 1.25 mtr long bend to shape as per site requirement fixed to pole /wall with 40mm x 5 mm size flat iron clamp -02 Nos,nuts ,bolt, washer etc complete all as specified & directed.

S & F in repair LED luminairs 600mm x 600 mm,35/36 watt,220 volt AC recessed type with high efficiency PMMA diffuser soft free light complete with drivers, holsers, LED lamps suitable roof ceiling including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed.

S & F for HDPE pipe of 20 mm dia sutable for 6 Kgf/sq.cm working pressure complete all as specified and directed by Engineer-in-Charge.

M/S KAMLESHWAR SINGH

upadhyay engineers and consultant

Balaji Construction And Company