General Fund

Drilling of Bore well by down the hole hammer drilling after feasibility report of Geologist to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time (A) up to 90.00 m depth

Drilling of Bore well by down the hole hammer drilling after feasibility report of Geologist to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time (B) above 90.00 m up to 150.00 m depth

Supply, delivery and erection of 180mm dia OD PVC 6 Kg/cm2 casing pipe of 6 mts lengths including cost and conveyance of all materials and labour charges etc. complete as directedcted by the Engineer in charge of the work. 180 mm dia OD PVC 6KSC casing pipe

Supply & Fixing of 180 mm dia PVC Bore Cap per 1No

Supply and fixing of 50 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 ISI mark with GI fittings including the cost of pipe & its fittings & labour charges complete

Supply and Transportation of THREE PHASE 7.5 HP, 20-24 Stage, 5 star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with water proof winding, Pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415V ± 10% , Three Phase 50 Hz AC supply,etc complete for 6" Bore well.

Supply of WPTC (Weather Proof Twin Core) 6 Sqmm ISI Alluminium Wire.Makes: Gold Medal / Million / GM / Vimal / Finecab / Nakoda / Plaza/ Payal / Sudhakar/ Rajnigandha/ Airson/Orbit/ollvin/Beljin ( Service Main)

Supply of 3 Core 4 Sqmm Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990. Makes: Finolex / RR Kabel/ Polycab / Havells / KEI/Gloster ELEC-1.6.3

Supply, and delivery of 50mm GI Long Couplings suitable for 50mm Nominal Bore GI pipe Medium grade porperties etc., complete as directed by the Engineer in charge of the work. (Quotation)

Fabrication ,transportation and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. 1.Voltmeter ; 0-500 V 96x96mm size. Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab - 1No 2.0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size). Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab- 1No. 3.Single phase preventor of suitable range Makes: L&T / Minilec / Powertec. - 1No. 4.32 A TP, 10KA MCB. Makes: Legrand / Schneider / - 1No 5.Indication lamps (R-Y-B) with switch control - 1set 6.Voltmeter & Ammeter selector switch - 2 Nos 7. Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos /Havells. above 7.5 HP to 12.5 HP with Star- Delta Starter of Make C&S/Crompton / L&T / Siemens/BCH above 7.5 HP to 12.5 HP with Star- Delta Starter of Make: C&S/Crompton / L&T / Siemens/BCH.

Geological Survey Charges

Erection of New Submersible Motor Pumpset including its fittings & labour charges complete.(Quotation)

Supply, delivery and fixing of the Bore well materials including cost and conveyance of all materials charges and labour charges etc complete. (Based on Local Quotations) 2" Pipe fitting MS Clamp set

Supplying & fixing Gunmetal (GM) Horizontal Check (Non return) Valve as per IS-778 I-class heavy duty - 50 mm NB Size