Construction of Central Bank of India Office building at Amaravati, Andhra Pradesh

DSR Total with NON DSR TOTAL AMOUNT

DSR Total with NON DSR TOTAL AMOUNT

ABSTRACT OF COST-CIVIL

S NO ITEM OF CIVIL WORK

All Figures are in Rs. All Figures are in Rs.

1.00 Earth Work Rs. 11148880 0

2.00 Concrete Work Rs. 1154896 0

4.00 Brick Work Rs. 11949928 0

5.00 Marble Work Rs. 303850 0

7.00 Steel Work Rs. 1462983 0

8.00 Flooring Work Rs. 15789507 10579402

9.00 Roofing Work Rs. 852611 4704039

10.00 Finishing Work Rs. 12294876 0

11.00 Aluminium Work Rs. 351258 2951956

12.00 Structure Glazing Rs. 13033835 0

13.00 Water Proofing Rs. 8082804 0

15.00 Road Work Rs. 1927233 0

16.00 Rainwater Harvesting Work Rs. 595651 0

17.00 Miscellaneous Work Rs. 0 5755244

Total Amount Rs. 315798944

Total Amount Rs. 315798944

Contractor 3 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

1.00 2.0 EARTH WORK

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm

deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal

of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers

1.03 2.25 not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 3705.00 Cum 196.00 726180.00

50 m and lift upto 1.5 m.

Disposal of surplus earth by mechanical transport including loading, unloading for a lead upto 10.00

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and

dressing complete.

2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 655.00 Litre 234.75 153761.25

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment

(excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart

2.35.3 including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse

sand) to match the existing floor :

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 1178.00 Sqm 310.05 365238.90

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto

1.09 2.25(a) a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in 275.00 Cum 700.50 192637.50

foundation trenches, plinth, sides of foundation etc. complete for all lift.

Total Earth Work : 11148879.86 0.00

2.00 4.0 CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - All work up to plinth level:

1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40

mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including

attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses,

2.02 4.2 parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five

level, excluding the cost of centering, shuttering and finishing :

i) 4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1.00 Cum 9895.20 9895.20

1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources: 6 graded stone aggregate 20

mm nominal size derived from natural sources)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse

sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of Per 50 kg

cement as per manufacturer's specification. cement

Contractor 4 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using

2.05 4.13 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a 41.00 Sqm 146.15 5992.15

piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill)

derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural

2.06 4.17 sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated 121.00 Sqm 749.30 90665.30

and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top

Extra for concrete work in superstructure above floor V level for each four floors or part thereof by

mechnical means.

Total Cement Concrete work : 1154896.15 0.00

3.00 5.0 R.C.C. WORK

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended

proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction

3.01 5.33 of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the

minimum specified cement content in design mix shall be payable separately. In case the cement

content in design mix is more than 110% of the specified minimum cement content, the contractor shall

have discretion to either re-design the mix or bear the cost of extra cement.

5.33.1 All works upto Plinth level

5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum 2592.00 Cum 9655.70 25027574.40

3.02 5.33.2 All works above plinth level upto floor V level

5.33.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum 1265.00 Cum 10011.35 12664357.75

3.03 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. 414.00 Cum 355.65 147239.10

Analysed on Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding

DSR all complete at all level and height

CRS TMT bars of grade Fe-550D. 669388.00 Kg 129.00 86351052.00

4.04 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

a) 5.9.1 Foundation, footing, bases of columns etc. for mass concrete 710.00 Sqm 392.15 278426.50

b) 5.9.3 Suspended floors, roofs, landings, balconies and access platform 4874.00 Sqm 927.25 4519416.50

c) 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers 4755.00 Sqm 736.40 3501582.00

d) 5.9.19 Weather shade, Chajjas, corbels etc., including edges 262.00 Sqm 951.10 249188.20

e) 5.9.7 Stairs, (excluding landings) except spiral-staircases 80.00 Sqm 764.95 61196.00

f) 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 1382.00 Sqm 961.30 1328516.60

g) 5.9.4 Shelves (Cast in situ) 51.00 Sqm 927.25 47289.75

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses,

bands, copings, bed plates, anchor blocks and the like

i) 5.9.16 Edges of slabs and breaks in floors and walls

j) 5.9.14 Extra for shuttering in circular work (20% of respective centering and shuttering items) 28.00 Sqm 192.26 5383.28

k) 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 5827.00 Sqm 842.50 4909247.50

4.05 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 203.00 metre 78.40 15915.20

Contractor 5 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping

4.06 5.11 etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every

additional height of 1 metre or part thereof (Plan area to be measured).

5.11.1 Suspended floors, roofs, landings, beams and balconies (Plan area to be measured) 6205.00 Sqm 384.30 2384581.50

4.07 MR Core cutting for fire & plumbing

4.00 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 509.00 Cum 7132.25 3630315.25

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement: 6 coarse sand) 128.00 Cum 9105.95 1165561.60

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for

each four floors or part thereof by mechanical means.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundations and plinth in :

6.12.2 Cement mortar 1:4 (1 cement :4 coarse sand) 1.00 Sqm 905.05 905.05

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 442.00 Sqm 1123.80 496719.60

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by

mechanical means.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with

Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure

4.08 6.38 above plinth level up to floor V level in cement mortar 1:4 (1 cement: 4 coarse sand ). The rate includes 82.00 Cum 10195.45 836026.90

providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300 mm thick

with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super

structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved

block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge.

(The payment of RCC band and reinforcement shall be made for seperately).

Total Brick Work : 11949928.40 0.00

5.00 8.0 Marble WORK

Contractor 6 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine

cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,

approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse

sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including

rubbing, curing, edge moulding, facia and polishing to edges to give high gloss finish etc. complete at

8.2.2 Granite Stone Slab of Colour Black, Cherry/Ruby red

i) 8.2.2.1 Area of slab upto 0.50 sqm 2.00 Sqm 5413.50 10827.00

ii) 8.2.2.2 Area of slab over 0.50 sqm 42.00 Sqm 5136.30 215724.60

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform,

vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar

taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep

and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and

5.03 8.10 embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and

finished smooth.

8.10.2 Granite Stone of approved shade 7.00 Sqm 4051.85 28362.95

Total Marble Work : 303849.55 0.00

6.00 9.0 Wood WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

6.01 9.1 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast

lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood 6.00 cum 142949.70 857698.20

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,

core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 591.00 Sqm 2392.65 1414056.15

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt /

suede finish with high density protective surface layer and reverse side of adhesive bonding quality

conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of

flush door shutters (over all area of door shutter to be measured).

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than

6.05 9.96 grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws

etc. complete :

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade

6.06 9.97 AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of

6.07 9.113 approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- 102.00 Sqm 850.05 86705.10

Contractor 7 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade

6.08 9.97 AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc.

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete

as per direction of Engineer-in-charge.

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not

6.10 9.101 less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with

necessary screws etc. complete.

9.101.2 Twin rubber stopper 112.00 each 72.35 8103.20

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand

6.11 9.83 logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), 112.00 each 1124.85 125983.20

with necessary accessories and screws etc. complete.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts,

6.12 9.53 nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 814.00 each 228.85 186283.90

coarse sand: 6 graded stone aggregate 20mm nominal size).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded)

6.13 (overall area of door shutter to be measured):

9.24.1 Rectangular or square 143.00 Sqm 199.15 28478.45

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on

vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating not less than 120

gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed Door Shutters. The frame shall be filled

with mineral wool Insulation having density minimum 96Kg/sqm. The frame will have a provision of G.I.

anchor fastners 14 nos (5 each on vertical style & 4 on horizontal style of size M10 x 80) suitable for

fixing in the opening along with factory made template for SS ball bearing hinges of size 100x89x3 mm

for fixing of fire rated glazed shutter. The frame shall be finished with an approved fire resistant primer

or powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in-

Charge. (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minutes Fire rating

conforming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by

Engineer-in-Charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side

rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6 mm thick G.I. sheet

6.15 9.162 (zinc coating not less than 120 gm/ sqm) duly filled mineral wool insulation having density minimum 96 91.00 Sqm 12017.90 1093628.90

kg/ cum and fixing with necessary stainless steel ball bearing hinges of size 100x89x3 mm of approved

make, including applying a coat of approved fire resistant primer or powder coating not less than 30

micron etc all complete as per direction of Engineer-in-Charge (panelling to be paid for seperately).

Contractor 8 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I.

beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/sqm) of size 20 x 33

mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c ,

including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on

G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS

16231 (Part 3):2016 and as per direction of Engineer-in-Charge with glass of required thickness having

6.16 9.164 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of 91.00 Sqm 43677.65 3974666.15

insulation (El20). The manufacturer have to give test report/certification of fire glass and the glass

should have the stamp showing the value of E, EW & El. The glass shall be tested in approved NABL

accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011

and accredited labs asort. The OEM shall have ISO 9001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification and India Design Mark.e b

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back

6.17 9.139 side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, 46.00 each 8366.15 384842.90

PELMET: Fabricate and install pelmet made of 19 mm thick board, up to 300 mm high and in line with

6.18 MR external glazing as per details of Architect. Rate to include finishing exposed surfaces of the Pelmet 312.00 Metre 692.00 215904.00

with 1mm laminate.

5.5mm THICK FSP HDHMR BOARD: Providing and fixing in wall lining, partitions etc. Confirming to

ASTM E-84-2021 class1 one side 1mm decorative Lamination, having even grade low emission, high

6.19 MR moisture resistance, fire resistance, borer, termite & fungus resistance, green material and

environmental friendly with necessary fixing arrangement and screws etc. , complete as per direction of

Engineer-in-Charge

5.5mm thick FSP HDHMR Board 10.00 Sqm 623.00 6230.00

WOODEN BATTENS: Providing and fixing specified wood frame work consisting of battens 50x25mm

8.27 fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 6.00 Cum 187277.65 1123665.90

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special

CRYSTAL-effect film to reproduce Sand-blasting effect on glass with customised designs, thickness of

2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5

pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch

(0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to

15yrs (indoors) .

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution

(premium GRIHA rated lacquered glass from Saint-Gobain) of approved color by Architect/ Client /

Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon/ double sided tape) on a

perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is mounted

on the RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating

6.22 MR process); opaque (if viewed against a support wall), coated with PU lacquer (50 micron thick); color 64.00 Sqm 4917.00 314688.00

consistency (measured by Minolta spectrophotometer CM5081); highly durable (passes PERSOZ

hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999);

environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content

(12% post industrial/ 6% post consumer); compressive strength (1000 MPa) & tensile strength (40

MPa), same as float glass;

Contractor 9 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame

and required board, including providing and fixing of frame work made of special section power

pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor

and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm

length or suitable anchor fastener or metal screws with nylon plugs and the studs 48mm wide having

one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor

and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts,

including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or

6.23 9.105 metal screws with nylon plugs at spacing of 450mm centre to centre, and fixing of boards to both side

of frame work byort. The OEM shall have ISO 9001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification and India Design Mark.e bushings to ensure

smooth, scratch-free stacking. The entire understructure will be powder-coated, with a finish thickness

of 40 to 60 microns, ensuring long-lasting durability and a high-quality appearance. The OEM shall

have ISO 9001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory

certification and India Design Mark.+/- 5mm to be considered for dimensions Length, Depth & height

and tolerance of 5% to be considered in thickness. The OEM shall have ISO 9001, BIFMA Level 2,

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum

9.105.1 (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks) 30.00 Sqm 2131.10 63933.00

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free

uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having

minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4

profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild

steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads,

interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket,

hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of

matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14,

plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion

(if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners,

including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap

between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer

rod of approved size and quality, all complete as per approved drawing conforming to CPWD

6.24 specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of

uPVC profiles to be as per design approved by Engineer-in-Charge.

Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance

coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.

Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the

manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with

structure height more than 20m for all wind speeds

Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the

manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with

structure height more than 20m for all wind speeds

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium

channel for roller track, wool pile, nylon rollers with SS 304 body.

Contractor 10 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25

i) 9.147.A4.1 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height 1.00 Sqm 10,993.55 10,993.55

upto 1.2 metre).

Using R4 series with frame (115 mm & above) x (45 mm & above) & both glazed and fly screen sash

ii) 9.147.A4.3 (44 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed 3.00 Sqm 12,372.25 37,116.75

panel along with multi- point locking system. (Height above 1.8m)

iii) 9.147.C1 Fixed window/ ventilator without mullion / transom.

9.147.C1.1 sing R1 series with frame (33 mm & above) x (35 mm & above). (Height upto 0.90 metre) 1.00 Sqm 8,247.25 8,247.25

9.147.C1.3 Using R3 series with frame (55 mm & above) x (45 mm & above). (Height upto 2.5 metre) 5.00 Sqm 7,080.05 35,400.25

Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc alloy (zamak)

iv) 9.147.B1 powder coated handle on every panel along with multi-point locking system, adjustable nylon rollers

with SS 304 body.

Using R3 series with frame (55 mm & above) x (40 mm & above) & sash (30 mm & above) x (74 mm &

above). (Height upto 2.5 metre).

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183

having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw,

rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of

Engineer-in-Charge.

Total Wood Work : 13863870.80 597742.00

7.00 10.0 STEEL WORK

Steel work welded in built up sections/ framed work, including cutting, hoisting, hinges, ms handle as

7.01 10.25 required, fixing in position and applying a priming coat of approved steel primer using structural steel

etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates, safety grilled door and similar works

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia

double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia

polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per

direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary

7.03 10.28 accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of 12.00 Kgs 772.40 9268.80

the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for

payment purpose only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc.).

Total Steel Work : 1462983.25 0.00

8.00 11.0 FLOORING

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12

mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @

3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Contractor 11 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the

manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory,

8.02 11.37 Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing 119.00 Sqm 1096.55 130489.45

with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching

pigment etc., complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours

8.03 11.41 and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments

etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and

matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles

will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber

mallet for placing the tiles gently and easily.

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with

water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours &

8.05 11.46 shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand),

jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement &

matching pigments etc. complete.

FLAMED FINISH GRANITE FLOORING : Providing and laying flamed finish Granite stone flooring in

required design and patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement

8.06 11.55 mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement

slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete

as specified and as directed by the Engineer-in-Charge :

11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. 263.00 Sqm 3186.70 838102.10

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as

curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone

slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed

with cement slurry and pointing with white cement slurry admixed with pigment of matching shade

including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-

11.56.2 Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red 176.00 Sqm 4481.30 788708.80

Granite stone slabs 18 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average)

Analysis of thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with

DSR pigment to match the shade of the slabs, including rubbing and polishing complete.

8.09 11.24 Extra for pre finished nosing to treads of steps of marble stone. 370.00 Metre 719.90 266363.00

8.10 11.25 Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre. 126.00 Sqm 851.80 107326.80

Contractor 12 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar

refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped

surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse

sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including

rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm

height along the parapet walls in the same manner.

Providing and installation (by spray method) of projected cork spray for interior, exterior wall and roofing

surfaces. Wall surface must be dry, smooth and provided by civil contractor or client so the final finish

can be desired and standard. Product with 2-3mm spray to achieve best of the product advantages as

high performance against thermal conductivity, acoustic and thermal insulator, waterproofing,

ecological, anti-oxidant, anti-bacterial, rot proof, anti-humidity, green building, sustainable, organic &

natural material. Product must be sprayed over dry, levelled and smooth wall/ roof surfaces in dust free

and non-rainy/non humid climate condition for better performance.

Interior & Exterior projected cork spray must comply with below mentioned quality and technical

standards. Adhesion resistance by pull-off test - EN-ISO 1524: 2000 - ≥ 1,9 N/mm2.Thermal

conductivity - UNE-EN 12667 - 0,075 W/m. ºC.Tensile strength and elongation at break - EN-ISO 527-4

- 0,36 Mpa.Crack bridging capability - EN 1062-3:2008 - A1 (-20ºC).Thermal compatibility (freeze-thaw

cycles) - EN 13687-5 - ≥ 0,8 N/mm2.”No bubbles and cracks”.Water vapor permeability - EN ISO 7783-

1(-2) - Sd< 5m Class.Hazardous substances - EN 16516:2018 - Complies with 5.3.Volatile organic

compounds (VOC)- UNE EN ISO 17895 - Maximum product content 15.Sound absorption - EN ISO

354:2004 - aw = 0,10. installation/spray on façade and roofing saves 20%-25% of AC consumption and

made of 100% natural organic materials as base material 96% of cork granules, it helps government

agencies, engineers, architects, project owners to achieve green building and sustainable compliances.

Product must be with 10 years of warranty with acceptable aging decolouration with times. Spray

method and wall preparations as per company standards shall not be sprayed over non recommended

wall conditions and colour or patterns as per project architect or engineer approval.

EXTERIOR GRADE COMPACT HIGH-PRESSURE LAMINATE (HPL) CLADDING: Providing and fixing

6mm thick Suede Finish Greenlam, or equivalent exterior grade Clad (High Pressure Laminates) made

up of 1300mm x 3050mm in size and conforming to EN 438-6:2016 standard, EDF Grade. Exterior

CLAD HPL should be made under high pressure, using thermosetting Phenolic resin treated kraft

layers, Amino plastic resin treated Exclusive & UV conforming Exterior Grade Decorative paper on both

sides and UV protection layer above the décor papers on both sides. Clad should be resistant to wet

conditions and meets permissible increase on mass, have density >1.35 gm /cm3, UV resistance of a

minimum of 4 on a grey scale rating after 1500 hours, Resistance to artificial weathering including light

fastness of a minimum rating of 4 (after 650 MJ/m2 radiant exposure). The product must conform to

European Fire-Retardant norms of Bs1d0 when classified in accordance with EN 13501-1.

Contractor 13 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

8.13 MR The Fire-Retardant Additive must be Halogen free to protect the environment. HPL must be a green

product conforming to GRIHA, GreenPro and Green Guard Gold certification and meet Anti bacterial

and Anti-termite property under JIS Z2801. Finish and color of compact laminates should be finalized

under direction of Engineer –in-charge. Clad should be installed on Aluminum tubular substructure in

the size of 50mm x 25/50mm or as per site requirement fixed at a maximum center-to-center distance

of 400mm to 600mm with the help of 5mm dia color matching rivets with sliding holes and fixed holes

on the HPL. The aluminum tubular substructure should be fixed on wall with the help of dead load

bearing brackets and wind load bracket by 10mm fastener. Wind load bracket will have vertical slot &

dead load bracket will have in horizontal slot & maintain 6mm both horizontal and vertical gap between

two installed clad panels. Shade/design of clad should be finalized under direction of Engineer –in-

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a

11.3 floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate 296.00 Sqm 614.20 181803.20

RAISED FALSE FLOOR: Providing and fixing removable raised/false access flooring with systemand

its components of approved make for different plenum height with possible height adjustment upto

50mm, comprising of modular loadbearing floor panels supported on G.I. rectangular stinger frame

workand G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed

by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of

thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size

100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts

screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in

position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate

using epoxy based adhesive of approved make or the machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized ofrectangular size

570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head

using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the

pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid,

rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance

8.15 between the bottom of the floor for electrical conduits and wiring etc. all complete as per the

architectural drawings, as specified and as directed by the Engineer-in-charge.

Contractor 14 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static

high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded

construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and

bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum

64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy

coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip

noncombustible Portland cementitious core mixed with lightweight foaming compound. The access

floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto

1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a

Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the

panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load

(UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved

manufacturers specification and as per the direction of Engineer-in-charge. All specification must be

printed on the side of the panel to ensure the quality of the product.

11.54.2 450mm Finished Floor Height (FFH). 24.00 Sqm 5977.35 143456.40

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising

8.16 MR In Natural Finish. Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete 127.00 Metre 346.00 43942.00

with Rubber/ PVC Jointers and Gasket.

CARPET TILES: Supply and fixing of Modular Carpet Tiles/ Planks made of Yarn type Nylon 6; Tufted

Textured Loop Pile manufacturedusing 100% Recycled Content Nylon, 100% Solution Dyed, Soil/Stain

Protection- Protekt²® , Preservative Protection - Intersept® , tiles of size 100 cms x 100 cms/ 50cm

50cm, with Glasbac having tufted yarn weight of 14-18Oz and average yarn density of 4500-6000

oz/cu. yd., Nominal total thickness 6 mm minimum, Minimum Recycle Content of 60% , Stability -

Delaminating ASTM D3936 ≥ 3.0 lbs/in, Wear - Castor Chair EN 985 > 2.4 Rating @25,000 cycle, ISO

10361 (ASTM D5417) ≥ 3.5 Rating @20,000 cycles (Heavy Use), Colour Fastness to Light AATCC 16

Part 3 ≥ 4 @ 60 Hours, Colour Fastness to Rubbing and Crocking AATCC 165 ≥ 4, Colour Fastness to

Water AATCC 107 ≥ 4, Flammability Methenamine Pill ASTM 2859 - 7 of 8 passing, Flammability -

Radiant Panel ASTM E648 > .45 watts/sq. cm., Flammability - Smoke density ASTM E662 < 450,

Antistatic AATCC 134 < 3.0 kV, Antimicrobial Treatment ASTM E-2471, Complete Inhibition AATCC

174 Parts II & III 99% reduction. No mold 7 Days. Acoustic - Nylon Absorption Coe cient - NRC 0.0 -

0.2, Dynamic Loading ISO 2094 < 15% Thickness loss, Green Carpet ASTM D5116, CRI Green Label

Plus certified for indoor air quality, NSF/ANSI 140 Gold including fixing/ installation with Low/ Zero VOC

content Adhesive.

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40

mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal

size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2

8.18 11.40 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 296.00 Sqm 978.45 289621.20

kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding

the cost of nosing of steps etc. complete.

12 mm THICK HDHMR BOARD RAW : 12 mm thick FSP HDHMR Board: Providing and fixing in wall

lining, partitions etc. Confirming to ASTM E-84-2021 class1, having even grade low emission, high

moisture resistance, fire resistance, borer, termite & fungus resistance, green material and

environmental friendly with necessary fixing arrangement and screws etc. , complete as per direction of

Engineer-in-Charge

12mm thick FSP HDHMR Board 1334.00 Sqm 730.00 973820.00

Contractor 15 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and fixing stainless steel clamps of required size and shape for anchoring stone wall lining to

the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse

sand), including making the necessary chases in stone and holes in walls wherever required.

VIC STRIP WALL PANELLING : Supply & Installation of Vicstrip (single slat/double slat)having size of

2400x600x12mm(+/- 2mm) thickness, backing of PET panel with front facia of 1mm laminate. The

product use for absorption of medium and high frequency range with NRC of 0.50 direct fix. Panel

Should be anti fungal as per ASTM G:21 and also Non-toxic, non-irritant, and fire complying with safety

standards confirm to Class 1 Fire Ratings tested as per BS 476 Part 6 passes (Fire Propagation) & Part

7 class2 (Surface spread of flame) ,for interior applications-The product should be 100% make in india

and OEM must have ISO CERTIFICATIONS- complying to- IGBC membership ISO 14184-2 (Release

formaldhyde) ISO 9001 (Quality Mangement System) ISO 14001 (Environmental Management System)

ISO 45001 (Ocupational helth & safety management system)

EMBOSSED PET PANEL : Supply & Installation of VMT Embossed 12mm PET panels which shall be

processed with VMT technology for surface customised colour options with available pattern as per the

designers requirement, the panel shall be made from-100% polyester fiber, with up to 70% recycled

fiber. size of panel 2800mm x 1200mm (± 0.5mm). Panel Should be anti fungal as per ASTM G:21

and also Non-toxic, non-irritant, and fire-resistant complying with safety standards confirm to Class 1

Fire Ratings tested as per BS 476 Part 6 (Fire Propagation) & Part 7 (Surface spread of flame) ASTM

8.22 MR. E 84 CLASS A, EN 13501 PART 1C,s2,d0 for interior applications. Noice reduction coefficient (NRC) - 50.00 Sqm 3000.00 150000.00

0.70 with 9 mm backing direct fix, 0.75 with 12 mm backing direct fix and 0.90 with 25 mm backing

direct fix. The product should be 100% make in india and OEM must have ISO CERTIFICATIONS-

complying to- IGBC Membership ISO 14184-2 (Release formaldhyde) ISO 9001 (Quality Mangement

System)ISO 14001 (Environmental Management System)ISO 45001 (Ocupational helth & safety

management system)

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The

ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering

process and finally finished by floating, brooming with wire brush etc. complete as per specifications

8.23 16.75 and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). 344.00 Cum 9823.80 3379387.20

(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per

design mix is payable/ recoverable separately).

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after per cm

making the joints dust free with high pressure air jet cleaners, all complete as per direction of the depth per

8.24 16.45 Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound 230.00 cm width 5.30 1219.00

impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board per metre

and IS: 1834 for hot sealing bitumen compound grade A.) length

Total Flooring Work : 15789507.40 10579402.00

9.00 12.0 ROOFING

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate 10

12.21 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per

standard design :

Contractor 16 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400

9.02 12.22 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, 26.00 Each 298.25 7754.50

rounding the edges and making and finishing the outlet complete.

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing

of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25

mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange

fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of

cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size

and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm

with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed

in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia

x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high

12.45 having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of

9.03 rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25

mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the

board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3

layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

WOODEN VENEER/ BAMBOO CEILING: Providing and fixing wooden veneer / bamboo ceiling by

Fixing Natural OAK Veneer 4 mm / natural bamboo shoots, mesh, screens, gall screen complete as per

9.04 MR the design on 12mm UnderlayFire retardent Ply fixed to a subframe made using 50mm X 50mm Kiln 49.00 Sqm 8223.00 402927.00

seasoned and chemically treated hollock wood fixed to RCC ceiilng using Fastners

Contractor 17 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

POLISH: Polishing in high gloss/matt finish melamine clear polish on wood work in required

color/wooden shade texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd

coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove

excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied

9.05 MR with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be 199.00 Sqm 2467.00 490933.00

allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to

dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear

polish and melamine thinner in required proportion.This 1st coat is allowed to dry for 24 hrs then this

dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final

melamine polish is applied with compressor pressure spray gun using melamine clear polish and

melamine thinner mixed in required proportion complete coat to be done in 1 or 2 layers without gap of

time.) as per direction of Engineer-in-Charge.

WAVE BAFFLE CEILING: To Supply & Install Custom made Vertical curve Polylam Blades Ceilings as

per the design intent. The vertically curve baffle system POLYLAM exhibiting space- delineating

characteristics. The system comprises vertically curve baffle with 75-150mm deep curved rafters

manufactured out of 1.2mm Aluminium to provide wave effect. The module for fixing baffle shall be

150mm centres as per design requirement. The carrier rails run perpendicular to the baffles axis and

can be mounted with M6 threaded rods using technical approved fasteners as per EN 13964

9.06 MR standards. The individual baffle lengths between 1200- 2400 mm can be selected. Baffles lengths less 102.00 Sqm 8998.00 917796.00

than 1500mm required two carrier rails mounted at the baffle ends. Baffle longer than 1500mm require

additional carrier rails mounted in the centre. Finish RAL Powder Coated.No Pre Coated products shall

be accepted. The spacing of the grid angles is according to the requirements of DIN 18168 and DIN EN

13964 and quality controlled to ISO 9001:2015 approved by SIS & LEED certification by Indian Green

Building council (IGBC).

Contractor 18 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

PERFORATED GYPSUM BOARD CEILING: Providing and fixing suspended false ceiling Size

1188x1998x12.5mm Globe perforation 8/18 with 8.7% perforation with NRC upto 0.6 : Regular round

perforation of glass fibre reinforced gypsum material, which includes providing and fixing GI perimeter

channels of size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of

27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves

and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk

with two flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x

10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55

mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the

intermediate channels with help of connecting clips and in direction perpendicular to the intermediate

channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm

9.07 MR dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done mechanically 11.00 Sqm 3152.00 34672.00

either with screw driver or drilling machine with suitable attachment. Finally the boards are to be joined

and finished so as to have a flush look with uniflot.

Cleaneo Technology - Air purification & Air quality.Active reduction of air polluants thanks to Cleaneo

Technology effectively reduces concentrations of VOC’s like alcohol, aldehydes, ketons and esters as

well as unpleasant odours from e.g. food or cigarette smoke

Air purification properties tested according to CEN standards and VDI guidelines by Fraunhof Insistute

for Building Physics.

The false ceiling surfaces shall be prepared to the satisfaction of the Architect, and shall be applied

with two coats of primer to the satisfaction of Architects.

300X1200 SUSPENDED FALSE CEILING : Providing and fixing suspended false ceiling microlook

tegular edge tile with 15 mm thickness, easily demountable tile, manufactured from High density glass

wool, visible surface is a batch painted glass tissue in white, back of the tile covered with glass tissue.

Size 1200x600x15mm Acoustics-Sound absorption(Alpha W) - 0.95 at 200 mm o.d.s as per EN ISO

354 Acoustics-Sound absorption Class - Class A at 200 mm o.d.s as per EN ISO 11654Acoustics-

Articulation class - 180 as per ASTM E1111, ASTM E1110,NRC - 0.9 NRC as per ASTM C

423,Humidity Resistance -Permanent ambient RH up to 95% at 30*C without sagging, warping and

delaminating ( 13964:2014). Fire Safety - Tested and classified as non combustible according to EN

ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501-1 - European

METAL CEILING FOR WET AREAS : Providing and fixing G.I Plain 84mm wide x12mm deep panel

with 16 mm flush profile to make it 100mm module of length upto 6mtr, shall be roll formed out of

0.5mm thick Powder Coated .The top coat of panel shall be 60 micron polyester coated finish in

approved colour. The panel shall be factory cut in up to 6Mtr OR required length. Accessories

Detail:Carrier: 32 mm wide and 39mm deep, made out of 0.5mm thick steel backed with enameled

black paint having cut out to hold on panel in a module of 100mm closed. The joint of two carriers shall

be joined by means of carrier splices maintaining a module of 100mm .4mm dia galvanized rod with

special height adjustment butter fly clips made out of SS steel sheet. The edge profile G.I.shall be

matching with the panel.

ACOUSTIC BAFFLE CEILING: Supply and installation of 2400 x 200x 18 mm PET Panels with a

9.10 MR density of 1850 gsm, material -100% polyester fibre , 100% recyclable and highly durable with GI U 10.00 Sqm 4137.00 41370.00

channel and clutch wire for hanging.

Contractor 19 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

OPEN CELL CEILING: Supply and installtion of Metal open Cell ceiling made of GI made and powder

coated of approved RAL shade. open cell ceiling with cell size of 50 x 50 mm. The cell is formed by

locking of upper sections and lower sections with U shaped profiles of 40mm height 15mm width and

595 mm length. The upper and lower sections when locked are locked with end panels on all 4 sides to

form a tile of 595 x 595mm. Each tile is installed on a 15mm T Grids system The grids system is formed

by locking of GI made Main T of 3000mm or 3600mm length and GI Cross T of 600mm at 600mm c/c.

GI wall angle 25x25 x0.4x3000mm {Material-GI(IS513),YS-280Mpa,Finish-Galvanised 90GSM(IS277)}

9.11 MR is fixed along the periphery of the ceiling with wooden screws at 300mm centers or Hilti HPS 6x40mm 316.00 Sqm 2800.00 884800.00

placed at 600 mm c/c. The grid system is suspended by 4 mm wire rod with adjustable clip, connected

to the grids system at 1200mm c/c. The suspension rod with clip is fixed to the slab by means of soffit

cleat and rawl plug ( fastner), at 1200mm c/c. Gyproc® soffit cleat 27x37x25x1.6mm {GI(IS513)YS-

260Mpa, Finish-Galvanised 120GSM(IS277) } is fixed with Gyproc® Rawl Plug- Ø8x45mm {Material-IS

513 CR1 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} Suspension

etc. all complete as per direction of Engineer-in-charge.

Total Roofing Work : 852610.65 4704039.00

10.00 13.0 FINISHING

10.01 13.4 12 mm cement plaster of mix :

10.02 13.16 6 mm cement plaster of mix :

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse

10.03 13.11 sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). 2634.00 Sqm 518.55 1365860.70

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height

of 3 m or part thereof.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the

surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

13.83 Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved

brand and manufacture

13.45 Finishing walls with textured exterior paint of required shade :

10.08 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior

primer applied @ 2.20kg/10 sqm

10.09 13.114 Melamine polishing on wood work (one or more coat). 6.00 Sqm 1192.30 7153.80

10.10 13.18 Neat cement punning. 234.00 Sqm 79.95 18708.30

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and

10.11 13.80 manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 130.00 Sqm 156.05 20286.50

13.37 Washing with lime to give an even shade :

13.37.1 New work (three or more coats) 1.00 Sqm 39.05 39.05

Total Finishing Work : 12294876.25 0.00

11.00 21.0 ALUMINIUM WORK

Contractor 20 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up

standard tubular sections/ appropriate Z sections and other sections of approved make conforming to

IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up

the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.

11.01 21.1 Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless

steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

(Glazing, paneling and dash fasteners to be paid for separately) :

21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) 32.00 Kg 530.90 16988.80

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making

11.02 21.1.2 provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket

required (Fittings shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron 49.00 Kg 634.45 31088.05

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with

11.03 21.3 EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 6.00 Sqm 1505.25 9031.50

21.3.3 With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) 139.00 Sqm 1685.40 234270.60

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather

11.04 21.8 silicon sealant over backer rod of approved quality as per architectural drawings and direction of

Engineer-in-charge complete

21.8.1 Upto 5 mm depth and 5 mm width 8.00 metre 96.75 774.00

Providing and fixing aluminium casement windows fastener of required length for aluminium windows

with necessary screws etc. complete

21.15.1 Anodized (AC 15) aluminium 2.00 Each 89.40 178.80

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete

as per direction of Engineer-in-charge

21.16.1 Anodized (AC 15) aluminium 2.00 Each 107.90 215.80

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring

11.07 21.18 type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete 7.00 Sqm 5325.90 37281.30

as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with

SS screws etc .complete as per direction of Engineer-in-Charge.

21.12.1 Anodized (AC 15 ) aluminium tubular handle bar 6.00 Each 575.75 3454.50

Providing and fixing 12mm thick toughened glass in Aluminium frame work including sealing with

11.09 EPDM / Neoprene gasket all complete as per the architectural drawings and the directions of engineer- 5.00 Sqm 3595.00 17975.00

SINGLE GLAZED SLEEK PARTITION: Supply and installation of aluminum profile for single-glazed

straight partition with top, bottom and side profiles of size 21mm x 30mm natural anodised finish and

11.10 MR suitable gaskets for insertion with 10mm thick clear toughened glass. It consists of 2 way polycarbonate 31.00 Sqm 10965.00 339915.00

profiles, 90 Degree L Junction and T Junction profiles and suitable fasteners for fixing profiles including

installation charges.

Contractor 21 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

SINGLE GLAZED SINGLE LEAF DOOR: Supply and Installation of door frame size 55X36mm and

single leaf single glazed stile door frame size 40x82mm with seals natural/black anodized finish with

Hardware: Flush Hinges(4 Nos) & Lever Handle with Narrow sash Lock 35mm backset, oval

11.11 MR escutcheons, strike plate, EPC both side key-70mm and saint gobain exposed door closer with Hold 4.00 Nos 109646.00 438584.00

Open unit with insertion of 10mm thick clear toughened glass and necessary seals to be provided all

around the door frames and drop down seal.

FIBRE WALL COVERING: Supply & Installation of Glass fiber based homogenous Woven/ non-woven

.1mm thick, 100-200 GSM Density brethable Wall Coverings. Material to be fire certified with minimum

Euroclass BS1D0 certification under EN13501, no harmful chemical coated with Oekotex Standard 100

certification and non-toxic in nature for closed enviornments with A+ attested for emission in indoor air.

Installation to be done over smooth, dry and dust-free substrate as specified with OEM recommended

adhesive by the supplier's authorized installer team. Installation measurement as per the entire area

(concealed/visible) installed. Finished as per satisfaction of E.I.C. PAINTABLE

INSULATION : Providing and fixing thermal insulation with Resin Bonded Fibre glass woolconforming

to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall

with screw, rawel plug & washers and held in position by criss crossing Gl wire etc. complete as per

directions of Engineer-in-Charge.

Fabrication, Supply & installation of Top mounted SS 304 Grade satin finished railing for staircase area

made by using SS Top rail Ø50x1.5 mm Thk. mounted on SS baluster made of SS round tube baluster

of Ø50 x 1.5 mm thick with SS modular swivel neck to hold the top rail. The total height of the installed

rail including top rail will be 1050 mm from FFL. Further the baluster will be mounted on Dia-100x6 mm

thick SS 304 grade base plate fixed on the Top of the RCC floor with 3 nos. of M10 x 120 mm long

11.14 MR HRD anchors or chemical based anchor. The baluster will hold 5 nos. of SS round tube of Ø16 x 1.5 153.00 Sqm 7000.00 1071000.00

mm thk. as horizontal/diagonal mid rails connected to the baluster with the help of CNC made modular

adjustable connectors. only argon welding allowed at site.The average spacing of baluster will be 900

mm. All material need to be in SS 304 grade with satin finish only.

Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50 m x2.00

m made of 40x40x6 mm angle iron or 50x50x3 mm hollow MS tube posts/horizontal members/bracings

covered with 1.63 mm thick MS sheet. The sheet shall be fixed with 30x5 mm MS flat by suitable

welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making

overall height as 2.5 m. MS channel ISLC 75 @ 5.70 kg/m, 50 cm long shall be provided at the bottom

having oval shaped holes of size 50x25 mm at both ends with 50 cm long MS angle 40x40x6 mm

bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by

providing 250 mm long expansion fasteners at both ends. The work shall be executed as per

11.15 16.81 drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic

diversion such as traffic signals during construction at site for day and night, glow lamps, reflective

signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided

shall be retained in position at site continuously including shifting of barricading from one location to

another location as many times as required during the execution of the entire work till its completion.

Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and

works required to execute the job. The barricading shall not be removed without prior approval of

Engineer-in-Charge.

(Note :- One time payment shall be made for providing barricading from start of work till completion of

work including shifting. The barricading provided shall remain to be the property of the contractor on 162.00 metre 3439.50 557199.00

completion of the work).

Contractor 22 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Total aluminium Work : 351258.35 2951956.00

12.00 25.0 STRUCTURE GLAZING WORK

Providing and supplying aluminium extruded tubular and other aluminium sections as per the

architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6

as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of

12.01 25.1 required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material 11198.00 Kgs 414.30 4639331.40

such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work.

Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken

for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of

12.02 25.2 structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights

and all levels, including

(a) Structural analysis & design and preparation of shop drawings for the specified design loads

conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure

without any failure), including functional design of the aluminum sections for fixing glazing panels of

various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts,

bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke

seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and

protection against fire hazard including:

(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of

required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving

perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel

framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent

bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and

in required numbers.

(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone

sealant compatible with the structural silicone sealant of required bite size in a clean and controlled

factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all

of approved grade, brand and manufacture, as per the approved sealant design, within and all around

the perimeter for holding glass

(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes

and profiles, as required as per the site conditions, to seal the gap between the building structure and

all its interfaces with curtain glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it

watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at

bottom (if required), making necessary holes of required sizes and of required numbers etc. complete.

This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium

grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc.,

enabling temporary structures and services, cranes or cradles etc. as described above and as

The item includes the cost of getting all the structural and functional design including shop drawings

checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost

of all mock ups at site, cost of all samples of the individual components for testing in an approved

laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection

till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight

structural glazing having all the performance characteristics etc. all complete as required, as per the

Architectural drawings, as per item description, as specified, as per the approved shop drawings and as

directed by the Engineer- in-Charge.

Contractor 23 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section

capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall

be paid for separately under relevant items under this sub- head. However, for the purpose of payment,

only the actual area of structural glazing (including width of grooves) on the external face shall be

measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of

structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National

Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies,

India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of

testing on the basis of cost of the work, cost of the test and importance of the work. Performance

Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other

accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per

1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per

ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind

pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test,

Tests to be conducted on site

6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml 1120.00 Sqm 3510.50 3931760.00

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12-

6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified,

comprising of an outer heat strengthened float glass 6 mm thick, of approved colour and shade with

reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear

12.03 25.3 float glass 6 mm thick, spacer tube 12 mm wide, dessicants, including primary seal and secondary seal

(structural silicone sealant) etc. all complete for the required performances, as per the Architectural

drawings, as per the approved shop drawings, as specified and as directed by the Engineerin-Charge.

The IGUs shall be assembled in the factory/ workshop of the glass processor.

(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For

payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the

grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm

Airgap + 6 mm Heat Strengthened clear Glass of approved make having properties as visible Light

transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20

%, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of

performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site

all accessories and hardwares for the openable panels as specified and of the approved make such as

heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates,

handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all

complete as per the Architectural drawings, as per the approved shop drawings, as specified and as

directed by the Engineer- in-Charge.

Contractor 24 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing, fabricating and supplying shadow box of required size and shape, for fixing in the spandrel

portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi

-rigid, inorganic, non-combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and

BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass

12.05 25.5 insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5 mm and nominal mass 20.00 Sqm 2159.65 43193.00

not less than 60 gm /sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay

process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board

including SS rivets, nuts, bolts, washers etc complete.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic

float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour

and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for

the required performances as specified, as per the Architectural drawings, as per the approved shop

12.06 25.6 drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area

of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone

sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel

Glass Panels in the curtain glazing is included in cost of relevent Item*).“

(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, having

properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light

reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. . 20.00 Sqm 2450.15 49003.00

The properties of performance glass shall be decided by technical sanctioning authority as per the site

Total Structural Glazing work : 13033835.40 0.00

13.00 22.0 WATER PROOFING

13.01 MR Single component PU +0.3mm PVC Membrane, complying to IS 15909 (Category A, Type 1) 711.00 Sqm 761.00 541071.00

1.2mm Single component PU + 1mm thick PVC Membrane, (Category A, Type IV), complying to IS

15909 on the mother/ RCC slab

13.02 MR Additionally, 2-component acrylic cementitious coating with protection of fiberglass mesh/ fabric over 804.00 Sqm 969.00 779076.00

the insulation/ screed concrete made for required slope/ drainage.

13.03 MR Providing and laying 1.5mm Fully Bonded HDPE membrane, complying to IS 16352 1166.00 Sqm 1453.00 1694198.00

Providing and laying 1.2mm thick HDPE membrane, complying to IS 16352 (for confined retaining

walls) + protection

Providing and applying Swellable Rubber (hydro expensive) for all applications except for Water

Storage Tanks where PVC Centrally Placed Water stops shall be used

Waterproofing of basements and/or other areas as required with 75mm guniting with 1:4 cement sand

mortar to the R.C.C. elements, after cleaning the surface off dust dirt including providing and fixing 100

x 100 x 10G Welded mesh and applying adhesive chemical Conbond SNA as required complete.

a) For Horizontal surface 1120.00 Sqm 969.00 1085280.00

b) For Vertical Surface 1315.00 Sqm 969.00 1274235.00

Total water proofing work : 8082804.00 0.00

14.00 20 PILE WORKS

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under

reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe

14.01 20.3 working load not less than specified, excluding the cost of steel reinforcement but including the cost of

boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete.

(Length of pile for payment shall be measured upto to the bottom of pile cap) :

Contractor 25 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading

platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and

dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-

14.02 20.6 charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing.

Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-

20.6.1 Single pile upto 50 tonne Safe capacity

20.6.1.1 Initial test (Test Load 2.5 times the Safe capacity) 5.00 per test 54771.50 273857.50

20.6.1.2 Routine test (Test Load 1.5 times the Safe capacity) 5.00 per test 19632.40 98162.00

Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance

with IS :14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean

14.03 20.9 concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting

the test & submission of results, all complete as per direction of Engineer-in-charge.

Note :- The inclusion of the above item in the schedule of work shall be judiciously decided by the

technical sanctioning authority, keeping in view the quality control, type of soil strata & importance of 216.00 per test 1153.20 249091.20

Providing and fixing permanent steel sheet piles of approved make and section including coating/anti-

14.04 MR corrosive treatment, driving, interlocking, welding, alignment and all incidental works complete as per 1428.00 Sqm 8998.00 12849144.00

specifications.

Total Pile work : 43721930.70 12849144.00

15.00 16.0 ROAD WORK

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after

excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller

including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth

with lead upto 50 metres.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks,

lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by

table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted

15.02 16.91 bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand

bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and

cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete

all as per direction of Engineer-in-Charge.

16.91.2 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. 1.00 Sqm 1091.50 1091.50

Construction of granular sub-base by providing close graded Material conforming to specifications,

mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads

15.03 16.78 & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and

compacting with vibratory power roller to achieve the desired density, complete as per specifications

and directions of Engineer-in-Charge.

16.78.3 With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20 95.00 Cum 2808.55 266812.25

Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in

position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse

sand), including making joints with or without grooves (thickness of joints except at sharp curve shall

not to more than 5mm), including making drainage opening wherever required complete etc. as per

direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved by Engineer-in-charge). 16.00 Cum 10117.60 161881.60

Contractor 26 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre

openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall

with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced

barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or

G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced

barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with

tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including

15.06 16.70 strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction

of Engineer-in- charge.

16.70.1 Made of G.I. wire of dia 4 mm 10.00 sqm 1017.80 10178.00

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XO) on 150 mm thick sub grade of

compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm

thick Jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all

complete as per direction of Engineer-in-charge.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using

cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal

size in appropriate proportions as per approved & specified design criteria, providing dowel bars with

sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using

needle and surface vibrators, levelling to required slope/ camber, finishing with required texture,

including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/

expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine,

providing and filling joints with approved joint filler and sealants, complete all as per direction of

Engineer in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design

mix is payable/ recoverable separately.

16.43.1 Cement concrete prepared with batch mixing machine 95.00 Cum 10529.35 1000288.25

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after per cm

making the joints dust free with high pressure air jet cleaners, all complete as per direction of the depth per

15.09 16.45 Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound 316.00 cm width 5.30 1674.80

impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board per metre

and IS: 1834 for hot sealing bitumen compound grade A.) length

Construction of dry lean cement concrete sub base over a prepared sub grade with coarse and fine

aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement

ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content

not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length

construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant,

transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne

vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge.

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road

15.11 16.47 marking paint of superior make as approved by the Engineer-in-charge, including cleaning the surface

of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete.

16.47.1 New work (Two or more coats) 48.00 Sqm 188.20 9033.60

Total Road Work: 1927233.35 0.00

16.00 23.0 RAINWATER HARVESTING

Contractor 27 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in

the required thickness, for all leads & lifts, all complete as per direction of Engineer-in

Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit, over

16.02 23.6 the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of 29.00 Cum 1538.25 44609.25

Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in

16.03 23.7 required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in- 29.00 Cum 1538.25 44609.25

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel

16.04 23.8 fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction 29.00 Cum 2024.50 58710.50

of Engineer-in-charge.

Replacement of M.S. foot rests in manholes including dismantling concrete blocks and fixing with

16.05 19.17 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20

mm nominal size):

19.17.2 With 20x20 mm square bar 156.00 each 621.95 97024.20

16.06 19.19 Providing and fixing in position precast R.C.C. manhole cover and frame.

19.19.3.1 Circular shape 560 mm internal diameter 12.00 each 1675.70 20108.40

Supplying, assembling, lowering and fixing in vertical position in bore well Unplasticised PVC medium

well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings &

accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

23.4.2 150 mm nominal size dia 240.00 metre 807.45 193788.00

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and

approved quality

19.19.1.1 Rectangular shape 600x450 mm internal dimensions 12.00 each 1437.65 17251.80

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in

cement mortar 1 :4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x61 O mm internal

dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and

weight of frame 15 kg), R.C.C. top slab with 1: 1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone

aggregate 20 mm nominal size), foundation concrete 1:5:10 fine sand : 10 graded stone aggregate 40

mm nominal size), inside plastering 12 mm thick with cement mortar 1 : 3 ( 1 cement : 3 coarse sand),

finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per

standard design:

Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

19.30.2 With common burnt clay non-modular bricks of each class designation 7 .5 6.00 each 8150.50 48903.00

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks

and S.W. drain pipe 100 mm diameter, 1.Bm long complete as per standard design.

19.32.1 With common burnt clay non-modular bricks of class designation 7.5 1.00 each 26861.90 26861.90

Total Rainwater Harwesting Work 595650.50 0.00

17.00 MISCELLANEOUS WORK

Contractor 28 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

MODULAR KITCHEN - UNDER COUNTER STORAGE CABINETS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with

openable shutters and sufficient number of drawers made of 18 mm thk. ISI Marked marine ply, all ply

to be laminated with 0.8 mm laminate.All shelves should be supported on approved quality SS pins and

shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at

least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All

Shutters finished in high gloss acrylic of approved. The cabinet boxes of floor units will be supported by

100mm height vertical adjustable legs which will be covered with PVC skirting in brushed aluminum

finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/slab using metal screws

of appropriate size and rawl plugs. Only front face area of cabinets and skirting from floor to top of

boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from

400X560X710MM to 1000X560X710MM (approx.) and join together as per site requirements etc.

MODULAR KITCHEN - OVERHEAD STORAGE WALL UNITS:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with

openable shutters and sufficient number of drawers made of 18 mm thk. ISI Marked marine ply. All ply

to be laminated with 0.8 mm laminate.All shelves should be supported on approved quality SS pins and

shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at

17.02 MR least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All 7.00 Sqm 8643.00 60501.00

Shutters finished in high gloss acrylic of approved. The unit shall be fixed to the floor/ wall/slab using

metal screws of appropriate size and raw plugs. Only front face area of cabinets and skirting from floor

to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be

varies from 400x560x710MM to 1000x560x710MM (approx.) and join together as per site requirements

17.03 MR Providing and fixing of Innotech with metal sides and quadro channels 20.00 Each 3833.00 76660.00

17.04 MR Providing and fixing of Innotech with metal sides and quadro channels 20.00 Each 4336.00 86720.00

SLIDING & FOLDING ACOUSTIC PARTITION : Supply & installation of Zilio Lite system of the sliding

folding partition type with the following details. Top rail/track: top rail/track shall be proprietary supplied

extruded aluminum Profile, finished in approved color anodized finish. Above fixed Mild Steel support

Structure: Mild Steel partition above sliding folding panels with 50mm thick rockwool insulation based

on the Acoustics required,finish for above support: gypsum cladding shall be provided with necessary

cut-outs for services, Mild Steel structure shall be created with the help of Anchor fastners,Box/square

Mild Steel pipes attached to the true slab. Moveable partition Panels : Panels to be filled with

necessary infills for acheiving the necessary nrc levels, finished on both sides with MDF, the panels will

have retractable Top and Bottom acoustical seals for better acoustics.Panel Mounting: panels shall be

mounted over proprietary supplied Zilio Aluminium & Mild Steel, frame work as per Architect/Clients

17.05 MR requirement.Suspension :The partition panels shall be suspended on track/rails with the help of top 0.00 Sqm 49834.00 0.00

hung mechanism.The top rail shall be fixed/suspended from the Mild Steel structure using threaded

rods. Quote also to include necessary supports, cutting, finishing for the sliding folding partition panel

top rail. Parking/Stacking module: the partition panels shall be centre/parallel/side stackable type as per

client's requirement. Retractable Operation/Mechanism - Manual Handle operation by an Internal crank

jack spindle mechanism. Telescopic panel - Manual handle operation by two different internal crank

jack mechanism with lever closer cut teeth gear.

ZILIO ZM - W100 Lite - Manual Suspension : 1,Track : 300.001.004,Sound Rating : 46dB,No. of

Panels - 8, Total Width : 9800mm,Clear Height : 2550 mm,True Celing Height : NA,Parking Layout :

Type A Center stacking,Surface : Laminate Finish

Contractor 29 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

ACCESS PANEL: Providing & fixing Access Panel of size mentioned below having - 1. Outer

aluminium frame - thickness : 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 2.

Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3.

Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc

Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness

2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard (Knauf Brand) Type: moisture resistant (MR)

in green plasterboard liner. 6. Screw (self-drilling black phosphate) - Material: mild steel C1018 - 1022.

7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock (spring catch/ catch

lock) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge -

Thickness : 4.0mm, Length: 82mm; Material: SS2172 (cold drawn steel wire). 10. Powder coating -

Color: white, RAL 9010

BLINDS : Providing & Fixing of Window Blinds as per the approved sample double honeycomb shades

having honeycomb within honeycomb with easy rise operating system as per following specifications

fabric specifications:

• Original Non-woven honeycomb shade shaving soft fabric appearance and high energy-efficient fabric

with high tear strength constructed out of Anti-static, resilent, colour fast & Sanitized Treat 100% spun

bonded non-woven polyester fiber & precision manufacture to form a hexagonally shaped duette pleat.

The Fabric is GREENGUARD certified and can attain an NRC value of 0.75. Certificates to be provided

at the time of delivery of material at site. Pleat dimension ¾ ”Honeycomb within a Honeycomb” with 3

air pockets for maximum energy efficiency.

• Shadings are duotone, with neutral tone facing the exterior and color facing the interior The Head rail.

Shall measure 50 wide and 35mm deep & thick 1.25mm extruded from alu. alloy& shall be powder

coated to a smooth finish with a thickness of 40 microns. Fabric shall be constructed from spun-bonded

polyester fiber, precision manufactured to form a hexagonally shaped, dual pleat, cellular construction.

17.07 MR All cords & cord holes shall be fully concealed inside the fabric structure. As each of the hexagonal cells 139.76 Sqm 20764.00 2902018.17

is formed individually, pleats operate independent of each other providing superior pleat retention &

structure strength. Installation brackets. shall be of high-tension spring steel suitable for overhead &

wall mounting 30mm Duette Hartford mounting bracket. Head rail covered with Sydney Valance of

height 80mm made up of Aluminium & L shape moving Rail includes “Click & Engage" method of

dimension 50mmx55mmsticked with integrated moving rail magnets provide a streamlined look, reduce

centre light gap, and promote easier operation. Polyester cord. Shall be 0.9mm in diameter & of woven

hollow core end cap shall be moulded acrylic color matched to the head & bottom rails. Bottom rail shall

be a single channel section, measuring 30mm wide and 12.5mmdeep & thickness 1-1.2mm extruded

from alu. Alloy & shall be powder coated with a smooth finish to a thickness of 15-25 microns. Hold-

Down bracket (optional) shall be molded in clear acrylic. It incorporates a pin for engagement with the

bottom rail end-cap. It shall be suitable for sill, face or side facing. Cord Equalizer shall be injection

melded from impact modified acrylic with a high flexural modulus

Contractor 30 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: CIVIL

DSR 2023/ Amount

S No MR ITEMS Description of Item Qty Unit Rate DSR NON DSR

All Figures are in Rs. All Figures are in Rs.

Providing & supplying of Window Blinds as per the approved sample in required shade and style

consisting, of Roller Blinds comprising of optima screen Fabric comprising of 22% polyester, 78% PVC,

Fabric weight 460-480G weight per sqm, Thickness 0.67 mm, Yarn count 18-19/cm, having fire

resistance standard – NFPA 701-89 small testing ISO-5659-2. The tear resistance should be complying

to ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and

safe installation, molded plastic with steel spring support and inserted into the tube end. It shall be

driven by a ball chain pulley with ball chain and can be positioned at right side or left-hand side of the

Shade. The Shade when lowering or raising, shall be automatically locked in position upon release of

the ball chain by means of a built-in friction lock. Universal clutch for left- and right-hand operation.

Chain Gear Ratio of 1.75:1. The END PLUG shall be molded of plastic with a steel location pin. The

17.08 MR plug shall be inserted into the tube end. (Opposite to the Drive Unit) for ease of installation. The 559.05 Sqm 2907.00 1625152.54

SUPPORT BRACKETS shall be of coated steel & provided with covers and used in right hand or left-

hand positions differentiated by the acceptance of the of the rectangular drive unit support or the round

idler plug pin. Can be installed (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket

should be protruding outside maximum of 80mm.The ROLLER TUBE shall be of extruded aluminium

with 37mm internal diameter & skin thickness of 1mm and shall incorporate a keyway integral with the

tube to accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom made up of powder coated

steel. The BALLCHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls molded co-axially

to it on 6mm pitch to form an endless ball chain. It is used for raising or lowering action of the shades.

Total Miscellaneous Work 0.00 5755243.70

Contractor 31 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with

1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core

cable in surface/ recessed medium class PVC conduit, with modular

A.1 switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS/HFFR PVC insulated copper conductor single core

cable etc. as required

Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point ( without independent switch etc.) with 1.5 sq.

mm FRLS/HFFR PVC insulated copper conductor single core cable

1.55 in surface/ recessed PVC conduit, and earthing the point with 1.5 sq.

mm FRLS/HFFR PVC insulated copper conductor single core cable

etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS/HFFR PVC

insulated copper conductor single core cable in surface/ recessed

A.3 1.12 medium class PVC conduit along with 1 No. 4 sq. mm FRLS/HFFR Metre 16290 373.00

PVC insulated copper conductor single core cable for loop earthing

as required. 6076170.00

Supplying and fixing following modular switch/ socket on the existing

1.24 modular plate & switch box including connections but excluding

modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 2 136.00 272.00

1.24.5 6 pin 15/16 amp socket outlet Each 2 219.00 438.00

Supplying and fixing modular blanking plate on the existing modular

A.5 1.26 plate & switch box excluding modular plate as required. Each 25 47.00

Supplying and fixing following size/ modules, GI box along with

1.27 modular base & cover plate for modular switches in recess etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC

insulated copper conductor single core cable in surface / recessed

medium class PVC conduit, 2way modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR

PVC insulated copper conductor single core cable etc. as required.

Contractor 32 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing 3

pin 5/6 A modular socket outlet and 5/6 A modular switch,

connections etc. as required. 182575.00

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing 6

pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,

connections etc. as required. 104122.00

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing 2

A.10 1.56 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular Each 145 757.00

switch, connections etc. as required. (For light plugs to be used in

non residential buildings). 109765.00

Supplying & fixing suitable size GI box with modular plate and cover

in front on surface or in recess including providing and fixing 25 A

modular socket outlet and 25 A modular SP MCB, "C" curve

including connections, painting etc. as required. 807.00

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring along with earth wire with the

following sizes of FRLS/HFFR PVC insulated copper conductor,

single core cable in surface/ recessed medium class PVC conduit as

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 10 373.00 3730.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 200 482.00 96400.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 360 1078.00 388080.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 360 1454.00 523440.00

Supplying and making end termination with brass compression gland

and aluminium lugs for following size of PVC insulated and PVC

sheathed / XLPE aluminium conductor cable of 1.1 KV grade as

Supply of following XPLE armourned 1.1 KV grade conforming to

I.S.7098/1554Aluminium Conductor Cables :

Supply of following sizes of PVC sheathed PVC/XLPE insulated

Aluminium conductor armoured cable of 1.1 KV grade conforming to

IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

Contractor 33 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

(b) 3.5 C x 95 Sqmm XLPE cable RM 100 1080.00 107999.81

(c ) 3.5 C x 70 Sqmm XLPE cable RM 50 849.95 42497.26

(d) 3.5 C x 50 Sqmm XLPE cable RM 50 637.50 31875.02

(e) 3.5 C x 35 Sqmm XLPE cable RM 50 475.26 23763.17

(g) 4 C x 16 Sqmm XLPE cable RM 200 262.50 52500.04

Supply of following sizes of copper cables -PVC sheathed

PVC/XLPE insulated Copper conductor armoured cable of 1.1 KV

grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively &

(a) 4 C x 16 Sqmm XLPE copper cable RM 250 1807.50 451876.04

(b) 4 C x 25 Sqmm XLPE copper cable RM 100 2816.25 281625.35

(c ) 3.5 C x 35 Sqmm XLPE copper cable RM 50 3357.51 167875.27

(d) 3.5 C x 50 Sqmm XLPE copper cable RM 50 4030.00 201500.02

Laying of one number PVC insulated and PVC sheathed / XLPE

power cable of 1.1 KV grade of following size direct in ground

including excavation, sand cushioning, protective covering and

refilling the trench etc as required.

10.1.2 Above 35 sq. mm and upto 95 sq. mm Meter 100 475.00 47500.00

10.1.3 Above 95 sq. mm and upto 185 sq. mm Meter 100 497.00 49700.00

10.1.4 Above 185 sq. mm and upto 400 sq. mm Meter 200 564.00 112800.00

Supplying and fixing single pole blanking plate in the existing MCB

DB complete etc. as required. 1400.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C"

curve, miniature circuit breaker suitable for inductive load of following

D.2 poles in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, MCB in the

MR existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 V, on surface/

recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing etc.

as required. (But without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 20 9081.00 181620.00

Supplying and fixing following rating, double pole, (single phase and

neutral), 240 V, residual current circuit breaker (RCCB), having a

2.14 sensitivity current 30 mA in the existing MCB DB complete with

D.5 connections, testing and commissioning etc. as required.

Contractor 34 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Supplying and fixing following way, single pole and neutral, sheet

steel, MCB distribution board, 240 V, on surface/ recess, complete

D.6 2.3 with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required.

(But without MCB/RCCB/Isolator)

2.3.3 12 way, double door Each 7 2871.00 20097.00

PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supplying and fixing following modular switch / socket on the existing

1.24 modular plate & switch box including connections but excluding

E.1 modular plate etc. as required.

1.24.6 Telephone socket outlet Set 119 168.00 19992.00

1.24.7 TV antenna socket outlet Set 31 168.00 5208.00

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the exisitng surface/recessed

steel/ PVC conduit as required 50220.00

Supplying and fixing of following sizes of medium class PVC conduit

along with accessories in surface/recess including cutting the wall

E.3 and making good the same in case of recessed conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC

insulated annealed copper conductor, unarmored telephone cable in

the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing two module stepped type electronic fan

regulator on the existing modular plate switch box including

connections but excluding

modular plate etc. as required. 10452.00

Installation, Testing and Commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5 sq.

E.6 1.45 mm FRLS/HFFR PVC insulated, copper conductor, single core Each 26 332.00

cable, including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required. 8632.00

Installation, Testing and Commissioning of exhaust fan in the

E.7 1.50 existing opening, including making good the damage, connection,

testing, commissioning etc. as required.

Extra for fixing the louvers/ shutters complete with frame for a

1.51 exhaust fan of all sizes. 5720.00

Contractor 35 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Brush Less Direct Current (BLDC) Fan with Remote

Supply, Installation, Testing and Commissioning of ceiling fan with

Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3

nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos.

canopies, shackle kit, safety rope, copper winding, steel/Al body.

Power Factor not less than 0.9, Service Value (CM/M/W) minimum

as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total

Harmonic Distortion)

E.9 9.1 less than 10%, remote (preferably mobile app based) for speed

control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise=75 0C (max.), insulation resistance more

than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply

Ceiling Fan compliant to IS 374:2019 fan i/c external connections

with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single

and earthing etc. as required.

9.1.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)

E.10 MR Supply of Exhaust Fan 300 mm Each 22 3500.00 77000.00

Providing and fixing M.S. Fan clamps of 16 mm dia M.S. bar, bent to

shape with Hooked ends in R.C.C. slabs or beams during laying,

including painting the exposed portion of loop, all as per standard

design complete

Providing and fixing circular/Hexagonal G.I. Box for ceiling fan

clamps, of internal dia 140 mm, 73 mm height, top LID of 1.5 mm

thick G.I. sheet with its top surface hacked for proper bonding, top

E.12 DSR 10.18LID shall be screwed into the G.I. box by means of 3.3 mm dia Each 26 220.65

rounded screws, one lock at the corners. Clamps shall be made of

12 mm dia M.S. bar bent to shap as per standard drawing.

Supply, Installation, Testing and Commisioning of Galavanized Iron

(GI) Raceways along with required suitable number of GI couplers

MR for joining raceways and fixing GI brackets and all accessories

complete in all respect as per the directions of engineer in charge

E.14 (a) 300mmx38mm(GI) - 3 compartment Mtr 100 2172.50 217249.61

(b) 225mmx38mm(GI) - 3 compartment Mtr 80 1775.00 142000.11

Supply, Installation, Testing and Commisioning of Junction boxes for

direct access to cables at the intersection of raceways supplied

completely with base and cover plates, height adjustable junction

box 65- 90 mm including all accessories ss plate of 3mm thick

E.15 complete in all respect as per the directions of engineer in charge

Contractor 36 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with cover

plate having locking arrangement and watering pipe of 2.7 Meter

long etc. with charcoal/ coke and salt as required. 100212.00

Providing and fixing 25 mm X 5 mm copper strip on surface or in

recess for connections etc. as required. 124600.00

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess

for connections etc. as required. 28700.00

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for

loop earthing as required. 16800.00

Providing and fixing of lightning conductor finial, made of 25 mm dia

300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6

mm thick G.I. base plate including holes etc. complete as required.

F.6 6.2 Fixing of lightning conductor finial (single prong) with base plate includingEach

holes etc. complete

4 as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the

F.7 6.3 finial or any other metallic object) by riveting / nut bolting/ sweating Each 4 139.00

and soldering etc as required. 1112.00

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or

F.8 6.6 surface of wall for lightning conductor complete as required.(For Meter 150 148.00

horizontal run) 47360.00

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or

F.9 6.70 surface of wall for lightning conductor complete as required.(For Meter 150 238.00

vertical run) 76160.00

G PANEL BOARDS

Designing, fabricating, transporting, unloading, storing, fixing in

position, testing and commissioning the following sheet steel cubicle

type panels fabricated from 1.6mm thick CRCA sheet, dust and

vermin proof, outdoor type double door with canopy, TPN Panels

with hinged lockable doors fabricated from 2mm thick CRCA sheet,

suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access

for cable alley and with segregated bus-bar chamber with tinned

aluminium bus bar and including supplying and fixing following

switchgears, meters and accessories, inter-connections, bonding to

earth, powder coated painting and marking as specified. Switch

boards complete as per schematic diagram:

Contractor 37 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in

Schematic diagram and as detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 630 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit

Breaker of fault breaking capacity 25 KA (ICS=ICU up to 433 V)

complete in all respect

TPN aluminum bus bars of minimum of 800 Amps capacity with heat

shrinkable colored sleeves and I/C DMC/SMC bus bars supports at

required intervals complete for cross section, size supports & their

spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB +ELCB - 20 Nos.

(b) 40 Amps, TPN, MCB +ELCB - 10 nos

Panel complete as above Each 1 425000 425000.00

G PANEL BOARDS

Contractor 38 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Designing, fabricating, transporting, unloading, storing, fixing in

position, testing and commissioning the following sheet steel cubicle

type panels fabricated from 1.6mm thick CRCA sheet, dust and

vermin proof, outdoor type double door with canopy, TPN Panels

with hinged lockable doors fabricated from 2mm thick CRCA sheet,

suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access

for cable alley and with segregated bus-bar chamber with tinned

aluminium bus bar and including supplying and fixing following

switchgears, meters and accessories, inter-connections, bonding to

earth, powder coated painting and marking as specified. Switch

boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in

Schematic diagram and as detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 200 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit

Breaker of fault breaking capacity 25 KA (ICS=ICU up to 433 V)

complete in all respect

TPN aluminum bus bars of minimum of 250 Amps capacity with heat

shrinkable colored sleeves and I/C DMC/SMC bus bars supports at

required intervals complete for cross section, size supports & their

spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 Nos.

(b) 40 Amps, TPN, MCB - 4 nos

Panel complete as above Each 7 225000.00 1575000.00

H SAFETY ITEMS

Providing and fixing MV danger notice plate of 200mm x 150mm

made of mild steel, atleast 2 mm thick, and vitreos enamelled white

on both sides and with iscription in single red colour on front side as

Online UPS- Input supply: Three Phase, Output supply: Three

Phase- Supplying, installation, Testing & Commissioning of following

a 26.2.3 capacity at fullPower

30KVA (Each load (Unity

operating temperature 0 Nos. 2 505748.00 1,011,496.00

Contractor 39 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Supplying,installation,testing and commissioning of 6 meter

Height hot dipped galvanized pole continously tapered (bolt

fixing type) octagonal Pole with top 70 mm dia and bottom 130

mm dia made of 3 mm thick H T sheet Steel conforming to grade

S 355 complete with G I base plate of size 220 mm (L) X 220

mm (B) X 16 mm thickness welded at bottom of pole complete with

4 Nos 20 mm dia 600 mm long foundation bolts confroming

to EN 8 grade, inbuilt / Vandal resistance, weathproof

electrical junction box having terminal block, 32A 4P MCB in

incomer & 16A DP MCB in outgoing for Pole Light ON/ OFF

etc mounted on bakelite sheet for looping in /looping out of

cables, with flush door having locking arrangement,

earthing arrangement (at atleast 0.5 m height) and

mounted on RCC foundation of size 500 mm x 500 mm x

1200 mm in ground and 300 mm above ground level with

foundation bolt duly embeded before casting and supply and

embedding of suitable size HDPE pipe sleeve for cable entry.

complete including erection of Pole complete in all respect as

per specification as reqd.

Supply, Installation, testing and commissioning of 500mm

long Single arm bracket of approved design and shape

H.4 NS/MR made up of MS metal with hot dip galvanised suitable Each 15 2000.00 30000.00

for pole top of 70mm dia complete with fixing arrangement as

Supplying & drawing 3x2.5sq.mm size FR PVC insulated copper

H.5 NS/MR conductor single core cable in the existing pipe as required Meter 150 400.00 60000.00

Supplying, installation on wall, testing and commissioning of

following capacity Air Insulated Compact Type Rising Mains for use

wire 415 volts, 50Hz A.C. supply with enclosure having IP-54 rating

after fixing the tap off boxes and all accessories, made of 1.6mm

thick steel sheet duly powder coated in convenient sections complete

I.1 3.8 with 4 Nos aluminium bus bars having current density of 130 A/ sq

cm at nominal current rating, necessary joints & expansion joints, fire

barrier at each floor, provision of tapping at every metre, continuous

earthing with 2 Nos aluminium strip of suitable size (one on each

side) including, G.I. clamping brackets, angle iron bracket, steel

fasteners, connecting to earthing system etc. as required.

Contractor 40 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO E&M DESCRIPTION UNIT QTY RATE

2025 All Figure are in Rs. All Figure are in Rs.

Supplying, installation, testing & commissioning of following capacity

End Feed Unit for the existing Air Insulated Compact Type bus

trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C.

supply made with 1.6mm thick steel sheet enclosure (IP54) duly

I.2 3.11 powder coated with provision of MCCB/ACB (but without

MCCB/ACB) complete with necessary joints including clamping

brackets, angle iron bracket, steel fasteners, connecting to earthing

system etc. as required

Supplying, installation, testing & commissioning of following capacity

Plug In/ tap off box on the existing Air Insulated Compact Type bus

trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C.

I.3 3.12 supply made with 1.6mm thick sheet steel enclosure (IP54) duly

powder coated with provision of MCCB/ACB (but without

MCCB/ACB) complete etc. as required

Total of Electrical items 14667783.90 5850683.35

Contractor 41 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: SUBSTATION

DSR E&M DSR NON-DSR

S No Description QTY UNIT Rate

All Figure are in Rs. All Figure are in Rs.

Supply, installation, testing and commissioning of following capacity (continuous loading) 11/0.433 KV Delta/Star,step down, 3 Phase, 50 Hz, Dyn 11 vector

group, Cast Resin / VPI (vacuum pressure impregnated) Dry Type, copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade

Cold Rolled Grain Oriented (CRGO) Core grade MOH or better) AN (air natural) cooled transformer suitable for indoor applications with Offload Tap Changer/ On

Load Tap Changer (OLTC) (upto 500 KVA offload and above 500 KVA On Load Tap Changer) on HV side having AVR relay and Remote Tap Changer Control

(RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote and manual operation of OLTC HV side in range of +5% to

-15% in steps of 2.5%, insulation class F (minimum), suitable for environment conditions class E4, suitable for fire behaviour class F1,climate class-C1, having

cable end boxes on HV side suitable for 3x300 sqmm XLPE cable of 11 KV grade with necessary hardware, clamps, lugs etc. for termination on HV/MV etc. for all

transformers, bus trunking arrangement on LV side complete with all accessories and safety provisions as per relevant IS Code ,The transformer shall be

provided with standard fittings/ accessories as per relevant IS and mentioned below, protection alarm/trip protection, 3 nos. of Polymeric Zinc Oxide surge

Arrestors on HV Side. Winding Temperature scanner (Digital) with alarm/Trip contacts with RTD Sensors per LV winding and space for mounting differential

protection CT's in LV chamber with neutral brought out separately including supplying and laying of copper conductor multicore control cable from transformer to

24.27 1 HT breaker/HT Panel for safety tripping, complete as confirming to IS-2026 Part-11, i/c supplying and grouting of suitable M.S. Channel with all accessories

,complete in all respects as required at site as per CPWD specifications . Design ambient condition : a) air temperature 50 0C, b) Relative Humidity 90 % Max, c)

Seismic Zone as per location of site, d) Altitude as per location/site. The transformer should have QR code which should contain drawing, test report OEM manual,

Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. All testing shall as per relevant IS Code. Noise level shall not exceed limits as per

NEMA TR-1 with all accessories running measured as per IEC 551/ NEMA Standard.

Fitting and Accessories : The following fittings shall be provided:- a) Two earthing terminals with the earthing symbol b) Rating and terminal marking plates; c)

Thermometer pocket with cap; d) Lifting lugs for the complete transformer as well as for core and winding assembly; e) Bi-directional flat rollers (for transformers

above 200 kVA); f) HV side neutral grounding strip (where one of the HV bushing terminal is connected to earth); g) Arcing horns or suitable rating lightning

arrestors for HT side – 3 Nos. for transformers up to 200 kVA; h) Bird guard; i) Jacking pads (for transformer above 1 600 kVA); j) Name Rating & Diagram Plate.

k) Monogram Plate.i) Additional neutral separately brought out on bushing for earthing. Level 5

24.27.37 1.1 630 KVA (losses at 50% loading < 1745watt, losses at 100% loading < 4850watt) 1 Each 1904199.00 1904199.00

25.1 2 Automatic Power Factor Correction (APFC) System

Automatic Power Factor Correction (APFC) System Supply, Installation, testing and commissioning of Automatic Power Factor Correction (APFC) panel, indoor type floor

mounted free standing totally enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %, 50 Hz AC System for Ambient temperature -5°C to +40°C, fabricated

in compartmentalised designed made of CRCA sheet steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c cleaning & finishing complete with 9 tank process

for powder coated of approved shade ( RAL 7032-Siemens Gray or as approved by Engineer-in-Charge), having front section (switch gear and control accessories) and rear

section capacitor and reactor, front and rear access, having suitable current carrying capacity, extensible TPN Aluminium alloy bus bar of high conductivity, DMC/SMC bus bar

supports, bottom base channel of MS Section, fabrication shall be done in transportable section, entire panel shall have common copper earth bar of minimum size of 25mm x

5mm with 2 nos. earth studs, the earth terminals provided on the body of capacitor bank shall also be bonded to the main capacitor panel earth bus with 2 nos. 8 SWG or 6 SWG

GI earth wires/ equivalent size of copper conductor cable, forced ventilation for maintaining temperature rise not more than 5°C from ambient, interconnections, connections with

14% detuned reactor and heavy duty 525 V ISI marked Impregnated MPP(Metalized Polypropylene) Capacitor (IS 13340 Part -1 & 2) APFC Panel shall be in compliance with IS

:16636 & CPWD Specifications etc. as per below details.

(A) Incomers Suitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of TPN 50KA breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating Lamp

set along with required Instruments and accessories with extended rotary handle and door interlocking arrangement. Current rating of the Incomer in ampere shall be APFC

Panel rating in KVAR x 1.4 x 1.5 or Nearest higher standards rating.

(B) Instruments & Indications i) 3-Phase current sensing APFC microprocessor relay/controller, advance 8/12 stages (8 stages for capacity below 100 KVAR and 12 stages 100

KVAR & above) with Communication Ethernet/RS485/SNMP port open protocol for BMS integration as per approved by Engineering in charge and having display of Phase wise

V, A, PF, Cos-Phi, Kw, KVA, KVAR, THD-V, THD-I, harmonics up to 31 level. 3 nos of dual core CT's accuracy class 1, 15VA at incomer of PCC Panel for APFC relay.

ii) Auto Manual Selector switch, auxiliary contactors with timer for delay in manual mode.

iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA, KVAR, THD-V & I, Frequency.

iv) Suitable rating control transformer shall be provided for control and indication circuit.

v) All components like control transformer, meter, relay and indicating lamp shall be protected by using suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS/HFFR 1100 V grade, PVC insulated multi stranded copper control wire.

(C) Bus Bars 1.3 Amp per Sq.mm,TPN, Electrolytic grade Aluminium bus bar of capacity 1.25 times of incomer rating as per CPWD specification.

(D) Outgoings (APFC Section) Selection of the capacitors combinations shall be for continuous rating and each capacitor bank shall have suitable capacity Heavy

Duty ISI Marked Capacitor, capacitor duty contactor,the capacitor shall be mounted on channel with base of perforated M S Powder coated sheet, connections

inter connections etc. and other features as per CPWD Specifications and relevant IS Code having following:

(i) Capacitor bank ratings & stages shall be as per the technical specifications sheet of NIT.

(ii) Capacitor will be MPP self healing type with discharge resistor, pressure release mechanism.

(iii) Since Capacitor Voltage is 525 Volts, thus higher KVAR has to be considered to get rated output at 415 Volts.

(iv) 14% Detuned Reactor of class H insulation & 150% linearity in series with Capacitor.

(Note: Technical specifications sheet for selection of the capacitors combinations shall be provided by the NIT Approving Authority with due consideration of

number of capacitors i.e. 1 KVAR, 2 KVAR, 3 KVAR, 5 KVAR, 10 KVAR.....for smooth correction).

Contractor 42 Digitally signed by NBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: SUBSTATION

DSR E&M DSR NON-DSR

S No Description QTY UNIT Rate

All Figure are in Rs. All Figure are in Rs.

Supplying, Installation, Testing & Commissioning of ‘Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating

of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory

and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing,

test report OEM manual,Geo- Tag of

manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings:

(A) Diesel Engine: Tourbocharged Diesel engine 4 stroke water cooled, multi cylinder, dynamically balanced fly wheel, electric

start of suitable BHP at 1500 RPM suitable for above output of alternator at 40 0C, 50% RH & at 1000 Meter MSL , capable of taking 10% over loading for one

hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with

service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, the

Electronic governor shall be as per ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS

10000, IS 10002, IS 13018 and as per CPWD specifications.

(B) Engine mounted Instrument Panel fitted with and having digital dis Plate for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(C) Alternator: Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 0C, 50%

RH & at 1000 Meter MSL. The alternator shall be having Screen Protected Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically balanced

rotor, capable of taking 10% over loading for one hour after 12 hours of continuous operation, self cooled,self-excited and self-regulated through AVR conforming

to IS13364(Part 2)/IS: 4722/BS 2613 suitable for tropical conditions and with class- H insulation.

(D) Base Frame & Foundation: Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which

shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.

(E) FUEL TANK: Daily service fuel tank of suitable liters capacity as per CPWD Specifications, fabricated out of 3 mm thick M.S. sheet complete with all standard

accessories and fuel piping between fuel tank and diesel engine with MS class ‘C’ pipes of suitable dia. Complete with valves, level indications & accessories as

required as per specifications.

(F) Exhaust System: Dry exhaust manifold with hospital type exhaust silencer and catalytic convertor.

(G) Starting System: 12V/24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial

excitation complete with suitable numbers of batteries (180 AH capacity lead acid SMF type) as required as per specifications. The battery shall be housed inside

the acoustic enclosure of DG Set.(H) Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction,

discharging hot air in to the atmosphere and the temperature rise inside the enclosure, noise level outside enclosure. The acoustic enclosure should be suitable

29.1 3 for cable connection/connection through bus-trunking. Such arrangements on acoustic enclosure should be water proof & dust-proof conforming to IP-65

protection. The enclosure shall be as per CPCB IV + or better norms etc. and as per CPWD specifications.

(I) AMF Panel: Free standing floor mounted IP 42 automatic mains failure control panel including auto by-pass, suitable for KVA as below for silent type DG set

complete with relays, timers, set of CTs for metering & protection and energy analyser to indicate currents, phase and line voltages, frequency, power factor,

KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase & Total), KW & provision for overload, short circuit, restricted earth fault, under frequency, power

(aluminium) and control (copper ) cabling of suitable size upto 15 meter between AMF panel, LT Panel and DG Set including connection interconnection etc. as

required, all complete and inter locking and communication/ Ethernet /RS485/SNMP port open protocol for BMS integration including suitable software, the panel

shall be of DG Set OEM make etc. as per approved by Engineering in charge and including the following:

Contractor 43 Digitally signed by NBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: SUBSTATION

DSR E&M DSR NON-DSR

S No Description QTY UNIT Rate

All Figure are in Rs. All Figure are in Rs.

1. Suitable numbers and appropriate capacity 4 pole motorised electrically operated draw out with cradle type 3 position ACB/ MCCB with electronic release for

O/C & E/F and shunt trip.

2. Auto/Manual/Test/Off selector switch

3. Protection for under and over voltage phase reversal (2 nos Over voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay).

4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for metering

5. Energy analyser unit to indicate current, Voltage (LN & L_L), kW, kVA (Phase & Total), Frequency, KWH, PF.

6. LED Indicating lamps for load on mains and load on set

7. Fuse/ MCB for instruments

8. Battery charger, complete with transformer/ rectifier, D.C. voltmeter and ammeter, selector switch for trickle, off and boost and current adjustment.

9.Main supply failure monitor

10.Supply failure timer

11.Restoration timer

12.Control unit with three impulse automatic engine start/stop and failure to start lockout.

13. Impulse counter with locking and reset facility.

14.ON/OFF/Control circuit switch with indicator

15.Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC sensing, Over Current, Unbalancing load with suitable number of relays and accessories

17. Maintenance notification based on Engine Run Hour & due date.

18. Load Management through PLC to achieve auto opening and closing of incomer breakers, bus coupler switching of essential panel, interlocking providing

signal to AMF Panel for load status and AMF shall give command to DG Set to auto start / auto stop depending upon load status and requirement etc. and

necessary hardware and software required to perform the operation shall be provided by the contractor

including all control wiring

B Sub Head - II : Cabling

M.R. 1 Supplying of one number PVC insulated and PVC sheatehed XLPE power aluminium conducter armoured cable of 11 KV (E) grade of following size etc as reqd. 50 Meter 4864.00 243200.00

22.1 2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand

cushioning, protective covering and refilling the trench etc as required.

22.1.2 2.1 Above 120 sq. mm and upto 400 sq. mm 50 Meter 694.00 34700.00

22.4 3 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.

22.4.2 3.1 Above 120 sq. mm and upto 400 sq. mm 25 Meter 146.00 3650.00

23.4 4 supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core,

XLPE aluminium conductor cable of 11 KV grade as required:

23.5 5 Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3

core, XLPE aluminium conductor cable of 11 KV grade as required :

5.4 1 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking 12 Set 8351.00 100212.00

arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

5.6 2 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking 12 Set 15004.00 180048.00

arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

M.R. 3 Providing and fixing 50 mm X 6 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation 200 Meter 5750.00 1150000.00

and re-filling etc. as required.

M.R. 4 Providing and fixing 50 mm X 12 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and 200 Meter 2000.00 400000.00

re-filling etc. as required.

Contractor 44 Digitally signed by NBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: SUBSTATION

DSR E&M DSR NON-DSR

S No Description QTY UNIT Rate

All Figure are in Rs. All Figure are in Rs.

M.R. 5 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. 100 Meter 2649.00 264900.00

M.R. 6 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. 100 Meter 627.00 62700.00

OUTDOOR SUB STATION

2-POLE STRUCTURE:

Supply, erection and commissioning of 2-pole structure for terminating 11 KV O.H. supply from supply company as per specifications and drawing. The 2-pole

structure shall comprise of:-

a) MS tubular swaged pole 11 mtrs high (410SP 24) (as per latest relevant BS standard)or as per Indian std., in cement concrete foundation 1:3:6 (1 cement : 3

coarse sand : 6 graded aggregate 40mm nominal size) including excavation and refilling etc. as required. The rate shall be inclusive of painting with 2 coats of

aluminium paint (on red oxide). The portion of pole under the ground shall be provided with 2 coats of bituminous paint -2 Nos.

b) Steel sections, channels angles, flats, clamps, GI nuts, bolts and required hardware etc of different sizes for cross arms, bracings, supports etc. for pole GODO

etc. including anticlimbing barbed wires (conforming to BS Standard) having 4 points barbs spaced 75 ±12mm apart. All steel structure shall be given 2 coats of

red oxide primer and 2 finishing coats of aluminium paint as required as per drawings and direction of Engineer-in-charge -Lot

c) Supply, installation, testing and commissioning of 11 KV class disc/pin/support insulators complete with clamps and fixing hard disc/pin/support insulators

complete with clamps and fixing hard wares etc. complete as required as per drawings and direction of Engineer-in-charge -Lot

d) Supply, installation, testing and commissioning of 11 KV station class thyrite type lightning arrestors complete with mounting arrangement (on all phases) -1

e) Supply, installation, testing and commissioning of drop out -lock out (DOLO) fuse, gang operating device (Air Break Switch) with pad locking arrangement

(operating rod to be supported properly), complete with operating handle and locking arrangement -1 Set

f) Supply, installation, testing and commissioning of GI stay set complete with 20mm dia 1.8 M long stay rod with 450 x 450 x 7.5 mm anchor plate with thimbles,

stay clamps, 7/4.00 mm dia GI stay wire, turn buckle (20mm x 600mm) strain insulator bow tightner in cement concrete 1:3:6 foundation as excavation and refilling

Earthing of poles with 2 Nos. 20mm dia M.S. rod earthing and connecting the poles with 25 x 6mm GI earth strip. - Lot

Earthing of lightning arrestors with 2 Nos. 32 x 6mm GI strip directly connected with GI pipe Earth station (2 Nos.) as per IS-3043 - Lot.

Two pole structure as described above. Set 1 125000.00 125000.00

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of cubicle type 11 kV metering panel fabricated out of 14 SWG CRCA

sheet steel, free standing floor readable dust and vermin proof with arrangement for sealing the covers and doors, re-inforcement of suitable size angle iron,

channels, T sections of flats wherever necessary. Cable gland plate shall be provided on bottom of metering panel. Panel shall be treated with allanti-corrosion

process prior to powder coating.

Approval shall be obtained from concerened Electricity Board for the shop drawings before fabrication.

The metering panel shall comprise the following

Trivector Meter of Secure make, accuracy class 0.5

MR 8 3 nos 11 KV cast resin CT's of 50/1 A amps CT ratio, 15VA burden and accuracy class 0.5

1 no. 3 phase potential transformer of approved make by Electricity Board Ratio 11000V/√3/110/√3 VA Burden 100VA Class 0.5

Ratio 11000V/√3/110/√3 VA Burden 100VA Class 0.5

One Set of Phase Indicating Lamps.

2 Sets of HRC fuses with fuse base (H.T. Fuse - 1A & LT fuse 2-6A).

1 Nos. indoor cable end box for suitable for 3C x 95 sq.mm.11 KV(E), aluminium conductor XLPE Al. cable (Incoming & Outgoing cable).

Note: The contractor shall get the Trivector meter, CTs' & PT tested by SEB and the charges for liaison for the same will be paid extra.

The metering panel shall be complete with all interconnections etc. as above including calibration of instruments as per Electricity Board. Set 1 132000.00 132000.00

11kV DISTRIBUTOR BOARD

Supplying, installing, testing and commissioning of Indoor 1no. Incomer and 01no. Outgoing Vacuum Circuit Breaker Panel Comprising of 11kV, 630Amp,

26.3kA/3-sec, Draw-Out type HT Vacuum Circuit breaker panel confirming to IEC 62271-200, IAC AFLR – 26.3kA for 1sec, LSC2B-PM Class, comprising of

630Amp, continuous rated aluminium busbars and droppers, 01no. Line-Earthing Trucks, 01nos. Rack-In-Rack-Out Handles and mandatory spares including

01no. Trip Coils, 01nos. Closing Coils, 01nos. Spring Charging Motors, 02nos. Space Heaters.

The Board shall consist of following panels:

INCOMER PANEL - 01nos., Each comprising of

11kV, 630Amp, 26.3KA/3-sec, Draw-Out Vacuum Circuit Breaker as per IEC-62271-100. Vacuum Circuit Breaker should have 03nos. encapsulated vacuum

bottles of same manufacturer as of circuit breaker. Motorized spring charging mechanism (230VAC) with integral spring charging handle for manual spring charge,

associated Shunt Trip/Close Coils (24VDC):

Current Transformers: 11kV, 300-150/1-1, Core1: Class 5P10, 5VA, Core2: Class 0.5, 5VA

Potential transformers: 11kV/rt3:110V/rt3, 50VA, Class 0.5

Accessories: Local Remote Switch, Breaker Control Switch (T-N-C), space heater with thermostat, DC & AC control circuit through MCB,

Contractor 45 Digitally signed by NBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: SUBSTATION

DSR E&M DSR NON-DSR

S No Description QTY UNIT Rate

All Figure are in Rs. All Figure are in Rs.

Indicating Lamps: for RYB, spring charge, DC Supply healthy, Breaker ON/OFF and TEST/ SERVICE position

Metering Instruments:

Multifunction Meter with RS485 port for MODBUS communication (Acc.Cl.0.5), Digital Ammeter (Acc.Cl.0.5), Digital Voltmeter (Acc.Cl.0.5)

Protection Relays:

01no. Flush-Mounted, Numerical based, 03-OverCurrent+01-EarthFault Feeder Protection Relay, providing OverCurrent (LowSet: 10%-250% / HighSet: 20%-

2500%), Earth-Fault (LowSet: 10%-200%/HighSet: 50%-1250%), ThreePhase Inrush Detection, CktBrkr Control, TripCkt Supervision, ThreePhase & Residual

Current Measurement, Non-Volatile memory for 100-event log, five-fault-record with time-stamp, Local HMI and user-programmable 4DI/6DO for future

deployment of interlocking/changeover scheme.

Relay should be communicable on MODBUS protocol.

Master Trip Relay - DA Aux.

Pluggable Relays for contact multiplication, anti-pumping, spring-charging indication etc. where applicable.

Additional facilities like Arrangement for connecting atleast one run of outgoing cables. Panel Illumination Lamp, Space Heater + Thermostat, Electrical or

Mechanical Anti pumping Protection, Test Terminal Block, Seperate PowerPack with associated BatteryBackup: 24VDC of suitable rating for each VCB, Panel

structure fabrication shall be made of sheet steel with anti-corrosive protection of zinc and aluminum coating. Safety Shutters, Continuous rated closing and

tripping coil. Panel design shall be one-second Fully Internal Arc Type tested for 26.3kA by the works manufacturing the item (principle/licensor/half-panel type-test

reports will not be accepted). Vacuum Bottles of same make as panel manufacturer. Complete Control circuit shall operate on 24VDC, except Spring-Charging-

Motor and SpaceHeater which shall operate on 230VAC.

OUTGOING PANEL - 01 nos. EACH COMPRISING OF

Same description as INCOMER PANEL above, except following changes:

Potential Transformer, Voltmeter, Under/OverVoltage Relay, R-Y-B Phase Indications are not required in Outgoing Panels

PANEL COMPLETE AS ABOVE 1 nos 1250000.00 1250000.00

PANELS WITH REAR ACCESS

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and commissioning the following sheet steel cubicle type panels fabricated from

1.6mm thick CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3

phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar chamber with tinned copper/aluminium bus bar as specified and

including supplying and fixing following switchgears, meters and accessories, inter-connections, bonding to earth, powder coated painting and marking as

specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

All MCCBs in Main LT Panel shall have minimum 50 kA breaking capacity

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the Specifications

Colour: Siemens Gray Powder Coated, as per approved sample.

ALL PANELS MUST BE EQUIPPED WITH GAS FLOODING SYSTEM

(NOTE: Interlocking of the incoming breakers and coupler to be coordinated with PLC in DG Control Panel with suitable control wiring and auxillary contacts left

Panel must have suitable entry for bus duct and rising main wherever required

INCOMER (Transformer)

1 nos 1000A FP electrically operated draw-out type ACB with microprocessor-based relay for O/L, S/C and E/F protection with time delay facility and fault type

indication, with Reverse Power Relay and three phase indicating lamps, 1no 96mm x 96mm multi parameter digital meter with LCD display for Voltage, Current,

Frequency, Power, Energy, Power factor, RS 485 port for connection to BMS system and set of suitably sized CTs including protection with 2A HRC fuses and

suitable number of auxilary contacts for electrical interlocking as described.

INCOMERS (DG SET)

MR 10 1 nos 800A FP electrically operated draw-out type ACB with microprocessor-based relay for O/L, S/C and E/F protection with time delay facility and fault type

indication, with Reverse Power Relay and three phase indicating lamps, 1no 96mm x 96mm multi parameter digital meter with LCD display for Voltage, Current,

Frequency, Power, Energy, Power factor, RS 485 port for connection to BMS system and set of suitably sized CTs including protection with 2A HRC fuses and

suitable number of auxilary contacts for electrical interlocking as described.

2 nos 630 A TPN MCCB with thermal-magnetic release setting of 80%-100%, rotary operating handle and ON indication with 1no 96mm X 96mm digital 3-phase

current Ammeter with suitably rated CTs and protected with set of 2A SP HRC fuses.

1 nos 400 A TPN MCCB with thermal-magnetic release setting of 80%-100%, rotary operating handle and ON indication with 1no 96mm X 96mm digital 3-phase

current Ammeter with suitably rated CTs and protected with set of 2A SP HRC fuses.

2 nos 250 A TPN MCCB with thermal-magnetic release setting of 80%-100%, rotary operating handle and ON indication with 1no 96mm X 96mm digital 3-phase

current Ammeter with suitably rated CTs and protected with set of 2A SP HRC fuses.

Contractor 46 Digitally signed by NBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: SUBSTATION

DSR E&M DSR NON-DSR

S No Description QTY UNIT Rate

All Figure are in Rs. All Figure are in Rs.

4 nos 100A TPN MCCB with thermal-magnetic release setting of 80%-100%, rotary operating handle and ON indication with 1no 96mm X 96mm digital 3-phase

current Ammeter with suitably rated CTs and protected with set of 2A SP HRC fuses.

10 nos 63A TPN MCB with rotary operating handle and ON indication with 1no 96mm X 96mm digital 3-phase current Ammeter with suitably rated CTs and

protected with set of 2A SP HRC fuses.

1no 800A FP electrically operated draw-out type ACB with ON/ OFF indication and suitable number of auxilary contacts for electrical interlocking as described

Equally sized three phase and neutral aluminium conductors busbar suitably sized to carry 1250A current and suitably insulated with colour coded Heat Shrink

Panel complete as above 1 nos 1875000.00 1875000.00

Supplying, erecting, testing and commissioning outdoor duty floor mounted weather proof IP54 feeder pillar fabricated as detailed in description given in E.1 above

but with double door (lockable outer door), sloping roof, water run-off gutter on three sides as per approved drawing, entire unit mounted on 50mm x 50mm x 5mm

angle iron with minimum 300mm long "legs":

1nos 40A TPN MCB.

1 no 96mm x 96mm multi parameter digital meter with LCD display for voltage & current with suitably rated CTs and MCB protection.

1 set of three phase indicating lamps with suitable protection.

MR 11 Busbar: Equally sized three phase and neutral copper conductors busbar suitably sized to carry 100A current and suitably insulated with colour coded Heat Shrink

1 nos. 25A TP MCB

3 nos. 40A DP ELCB.

18nos.6/10/16A SP MCB

2 nos. 16A water proof outlet.

Feeder Pillar complete as above 1 nos 90000.00 90000.00

Safety equipments

MR 1 Supplying & Erection of following safety equipments at suitable places as required.

MR a CO2 (Carbon Dioxide) type fire extinguisher Confirming to IS:15683 with cylinder fully charged of 4.5 Kg. capacity (ISI marked.) 2 Each 6400.00 12800.00

MR b ABC Powder type Fire Extinguisher (Stored Pressure type) Capacity 06 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609 (ISI marked.) 2 Each 3200.00 6400.00

MR c A set of 4 Nos. Fire Buckets with 50 mm x 50 mm x 6 mm thick angle iron suitable stand etc. as required (Confirming to IS-25461974). 2 Each 4500.00 9000.00

MR d Industrial First Aid small kit having Metal Box wall mounted with acrylic door as approved by St. JOHN AMBULANCE BRIGADE or Indian Red Cross Society as 2 Each 3500.00 7000.00

per IS code 2217 '1963

MR e Electric shock treatment chart of size 24" X 18" as per BIS 1986 duly framed in glass frame work i/c mounting arrangement. 2 Each 4500.00 9000.00

Supplying & Fixing of Fire retardant / Extinguishing Elect. Insulated mat of 3.0 mm thick + 10% according to IS: 15652, 2006 meeting requirements of IS: 3043, IS: 10 Sq Meter 1600.00 16000.00

5216 (Part 1,2& 3), IS: 8437 and IEC 479 Pub-1, Tested for breakdown strength, tensile/ elongation, ageing, properties, Insulations resistance,effects of acid,

alkaline, diesel & transformer oil, leakage current test, having min. width of 1000 mm + 20 mm. All allied material such as pu-resin, chemi bound (Hardener), spl.

PVC adhesive, liquid primer and sealing material and similar tape of matching colour and matching design tapes should be used to maintain any aesthetic look of

the insulation over the joints and corner as per in servicerecommendation of Annexure "A" Clause C of IS: 15652 and suitable for Class-C upto 33 KV etc

complete as required

Supplying & Fixing of Fire retardant / Extinguishing Elect. Insulated mat of 2.0 mm thick + 10% according to IS: 15652, 2006 meeting requirements of IS: 3043, IS: 10 Sq Meter 1200.00 12000.00

5216 (Part 1,2& 3), IS: 8437 and IEC 479 Pub-1, Tested for breakdown strength, tensile/ elongation, ageing, properties, Insulations resistance, effects of acid,

alkaline, diesel & transformer oil, leakage current test, having min. width of 1000 mm + 20 mm. All allied material such as pu-resin, chemi bound (Hardener), spl.

PVC adhesive, liquid primer and sealing material and similar tape of matching colour and matching design tapes should be used to maintain any aesthetic look of

the insulation over the joints and corner as per in service recommendation of Annexure "A" Clause C of IS: 15652 and suitable for Class-A upto 3.3 KV etc

complete as required

10.1 Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle 100 Each 598.00 59800.00

iron, 60 cm long and fixing the same in ground as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II

15.16 3 complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning

and protective covering etc., complete as required.

Contractor 47 Digitally signed by NBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: SUBSTATION

DSR E&M DSR NON-DSR

S No Description QTY UNIT Rate

All Figure are in Rs. All Figure are in Rs.

15.16.5 a 200 mm dia (OD-200 mm & ID-175 mm nominal) 100 Meter 733.00 73300.00

Based on Supplying, installation by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains/Bus Duct for use on 3 phase 4 wire

31.13 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly

powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints,

elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous

earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners,

connecting to earthing

system etc. as required

Contractor 48 Digitally signed by NBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Supply, Installation, Testing and Commisioning of SINGLE LEVER

CONCEALED BASIN MIXER (WALL MOUNTED) WITH SPOUT

1 MR (COMPOSITE ONE PIECE BODY) LPM should be 2.5 with suitable EACH 48 16080.00 771840.00

aerators as per GRIHA norms. Manufacturer should have valid

GRIHA certification

Supply, Installation, Testing and Commisioning of TABLE TOP

BASIN, SIZE: 630x460x130mm

Supply, Installation, Testing and Commisioning of suitable

3 MR compatible WASTE COUPLING 32MM- FULL THREAD- WITH EACH 48 2398.00 115104.00

CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioning of BOTTLE TRAP

(WITH INTERNAL PARTITION) 32mm SIZE WITH 300mm &

190mm LONG WALL CONNECTION PIPES & WALL FLANGE

Supply, Installation, Testing and Commisoning of RIMLESS, BLIND

INSTALLATION WALL HUNG WC WITH UF SOFT CLOSE SLIM

SEAT COVER, HINGES AND ACCESSORIES SET, SIZE:

Supply, Installation, Testing and Commissioning of PNEUMATIC

Supply, Installation, Testing and Commisoning of ANGULAR STOP

COCK WITH WALL FLANGE

Supply, Installation, Testing and Commissioning of CONCEALED

8 MR STOP COCK WITH ADJUSTABLE WITH WALL FLANGE 15mm EACH 48 4965.00 238320.00

Supply, Installation, Testing and Commisiong of HAND SHOWER

(HEALTH FAUCET) WITH 8mm DIA 1.2 METER LONG FLEXIBLE

TUBE AND WALL HOOK ALD-CHR-573 or equivalent. LPM should

be 3.8 with suitable aerators as per GRIHA norms. Manufacturer

should have valid GRIHA certification

Supply, Installation, Testing and Commisiong of PNEUMATIC

SINGLE PIECE SLIM CONCEALED CISTERN BODY WITH

10 MR INSTALLATION KIT & “S-TYPE” DRAIN PIPE CONNECTION SET EACH 48 8044.00 386112.00

FOR WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE). This

should be as per the GRIHA norms of 2L/4L LPF

Contractor 49 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality)

12 17.31 complete with 6mm thick hard board ground fixed to wooden cleats EACH 48 1607.95 77181.60

with C.P. brass screws and washers complete.

Providing and fixing C.P. brass angle valve for basin mixer and gyser

13 points of approved quality conforming to IS : 8931

18.53.1 15 mm nominal bore EACH 192 574.30 110265.60

Cutting chases in brick masonry walls for following diameter sand

cast iron/centrifugally cast (spun) iron pipes and making good the

same with cement concrete 1:3:6 (1 cement: 3 coarse sand: 6

14 graded stone aggregate 12.5 mm nominal size) including necessary

plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand)

Cutting holes upto 30x30cm in walls including making good the

18.76.1 With common burnt clay F.P.S. (non modular) bricks EACH 48 416.80 20006.40

Making chases upto 7.5 X 7.5 cm in walls including making good and

finishing with matching surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete as

per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes METRE 350 335.00 117250.00

18.7.3 25mm nominal outer dia pipes METRE 200 401.55 80310.00

18.7.4 32mm nominal outer dia pipes METRE 180 518.75 93375.00

18.7.5 40mm nominal outer dia pipes METRE 100 702.95 70295.00

18.7.6 50mm nominal outer dia pipes METRE 80 934.15 74732.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps

at 1.00 m spacing.

This includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in

Concealed work including cutting chases and making good the walls

18.8.1 15mm nominal outer dia pipes METRE 700 497.80 348460.00

18.8.2 20mm nominal outer dia pipes METRE 400 537.60 215040.00

18.8.3 25mm nominal outer dia pipes METRE 200 627.25 125450.00

18.8.4 32mm nominal outer dia pipes METRE 100 739.30 73930.00

Contractor 50 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Providing, fixing, jointing and testing in position of ISI marked UV

stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS

: 13592 suitable for rubber ring joints, including all neccessary

specials and fittings (confirming to IS:14735) i.e. bends, tees,

junctions (with or without doors), reducers, WC connectors,

couplers, expansion joints / bellows, cowels, clamps, rubber rings,

clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement

ceiling / external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from floor

under false ceiling or embedding the pipes laid under floors / building

19 in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand

MR : 4 graded stone aggregate 20 mm nominal size) including cost of

shuttering for proper completion of the work, breaking and making

good the walls and floors etc. after pipes have been duly laid and

tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with

nuts, washers etc on 50x50x5 mm slotted angle. The cost will

include all support arrangements. The work includes commissioning

of all pipes lines as per drawings and specifications and as directed

by engg-in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 800 536.00 428800.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 150 416.00 62400.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985)

UPVC pipes of min 6 Kg/ Sqcm rating with fitting for waste pipe

from fixtures to floor trap including reduces, enlarger, socket,

couplers, bends, tees etc including fixing at wall/ ceiling level

supported by clamp & hangers etc. cutting holes in wall/ floors/ slabs

and making good the same with cement concrete 1:2:4 complete as

Providing & fixing UPVC Floor trap of self cleansing design with

21 MR stainless steel grating complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 125 536.00 67000.00

Extra for providing & fixing 125 mm dia C.P. grating in place of C.I.

grating over floor traps.

Providing & fixing of SS Floor Cleanout, round or square with rubber

23 MR seal and flat round cover with screws and other required fitting EACH 125 1001.00 125125.00

complete as required.

MR Supply, Installation, Testing and Commisiong of HIGH FLOW EACH 22 18938.00

24 SINGLE LEVER CONCEALED DIVERTOR FOR BATH & SHOWER 416636.00

MR Supply, Installation, Testing and Commisiong of SPOUT FOR EACH 22 9377.00

BUILT IN BATH/SHOWER MIXER

MR Supply, Installation, Testing and Commisiong of OVERHEAD EACH 22 24100.00

SHOWER 350x350MM ROUND EDGE SQUARE HEAD SINGLE

FLOW (BODY & FACE PLATE STAINLESS STEEL WITH CHROME

PLATED) WITH RUBIT CLEANING SYSTEM

Contractor 51 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Supply, Installation, Testing and Commissioning of 15 litre geyser

Supply, Installation, Testing and Commisiong of SOAP DISH

Supply, Installation, Testing and Commisiong of TUMBLER

Supply, Installation, Testing and Commisiong of TOWEL RACK

600MM LONG WITH LOWER HANGER

31 MR Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 22 2045.00 44990.00

Supply, Installation, Testing and Commisiong of TOWEL HOLDER

Providing and fixing white vitreous china battery based infrared

sensor operated urinal of approx. size 610 x 390 x 370 mm having

pre & post flushing with water (250 ml & 500 ml consumption),

having water inlet from back side, including fixing to wall with suitable

brackets all as per manufacturers specification and direction of

Engineer-in-charge.

Supply Installation, Testing and Commisioing of Handicap Toilet

34 MR special fixtures to the complete satisfaction of the engineer in charge

(a) SITC of Grab Bar vertical swing white Each 5 9867.00 49335.00

(b) SITC of Grab Bar Left/Right 90 angle Each 5 7271.00 36355.00

(c ) SITC of Grab Bar 842mm long white Each 5 4664.00 23320.00

Providing and fixing C.P. brass bib cock of approved quality to

conforming to IS 8931.

a 18.49.1 15 mm nominal bore Each 48 506.80 24326.40

Providing and fixing C.P. brass long body bib cock of approved

36 18.51 quality conforming to IS standards and weighing not less than 690

a 18.51.1 15 mm nominal bore Each 2 798.95 1597.90

Providing and fixing C.P. brass stop cock (concealed) of standard

design and of approved make conforming to IS : 8931.

a 18.52.1 15 mm nominal bore Each 58 670.45 38886.10

38 18.9.6 50mm nominal outer dia pipes M 200 794.25 158850.00

Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end).

a 18.17.1A 20 mm nominal bore Each 80 539.95 43196.00

b 18.17.1 25 mm nominal bore Each 40 622.40 24896.00

c 18.17.2 32 mm nominal bore Each 16 689.60 11033.60

d 18.17.3 40 mm nominal bore Each 4 826.10 3304.40

e 18.17.4 50 mm nominal bore Each 4 1026.65 4106.60

Providing and fixing ball valve (brass) of approved quality, High or

low pressure, with plastic floats complete :

a 18.18.3 25 mm nominal bore Each 6 464.05 2784.30

Providing and fixing unplasticised PVC connection pipe with brass

18.21.1 30 cm length

a 18.21.1.1 15 mm nominal bore Each 100 85.00 8500.00

Contractor 52 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Providing and placing on terrace (at all floor levels) polyethylene

water storage tank IS: 12701 marked with cover and suitable locking

arrangement and making necessary holes for inlet, outlet and

overflow pipes but without fittings and the base support for tank

Excavating trenches of required width for pipes, cables, etc including

excavation for sockets, and dressing of sides, ramming of bottoms,

depth upto 1.5 m including getting out the excavated soil, and then

2.10 returning the soil as required, in layers not exceeding 20 cm in depth

including consolidating each deposited layer by ramming, watering,

etc. and disposing of surplus excavated soil as directed, within a lead

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm

Providing and fixing square-mouth S.W. gully trap class SP-1

complete with C.I. grating brick masonry chamber with water tight

19.4 C.I. cover with frame of 300 X 300 mm size (inside) the weight of

cover to be not less than 4.50 kg and frame to be not less than 2.70

kg as per standard design :

19.4.1 100 X 100 mm size P type

a 19.4.1.2 With Sewer bricks conforming to IS : 4885 Each 10 2685.20 26852.00

Constructing brick masonry manhole in cement mortar 1:4 (1 cement

: 4 coarse sand) with R.C.C. top slab with 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size),

foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded

stone aggregate 40 mm nominal size) inside plastering 12 mm thick

19.7 with cement mortar 1:3 (1 cement : 3 coarse sand) finished with

floating coat of neat cement and making channels in cement

45 concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate

20 mm nominal size) finished with a floating coat of neat cement

complete as per standard design :

19.7.1 Inside size 90 X 80 cm and 45 cm deep including C.I. cover with

frame (light duty) 455 X 610 mm internal diamensions total weight of

cover and frame to be not less than 38 kg (weight of cover 23 kg and

weight of frame 15 kg):

a 19.7.1.2 With Sewer bricks conforming to IS : 4885 Each 15 12711.80 190677.00

19.7.3 Inside size 120 X 90 cm and 90 cm deep including C.I. cover with

frame (medium duty) 560 mm internal diameter, total weight of cover

and frame to be not less than 208 kg (weight of cover 108 kg and

weight of frame 100 kg)

a 19.7.3.2 With Sewer bricks conforming to IS : 4885 Each 1 32719.50 32719.50

47 19.8 Extra for depth of manholes

19.8.1 Size 90x80cm

19.8.1.2 With Sewer bricks conforming to IS : 4885 Meter 15 8654.25 129813.75

19.8.2 Size 120x90cm

19.8.2.2 With Sewer bricks conforming to IS : 4885 Meter 1 10381.45 10381.45

Contractor 53 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Constructing brick masonry road gully chamber 50 X 45 X 60 cm with

bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500

X 450 mm precast R.C.C. horizontal grating with frame complete as

per standard design :

19.27.1 With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5

Supply, Installation, testing and commisioning of Domestic Water

Pumps(to lift water from underground domestic water tank to terrace

tank of building)Location - Near underground water tank with Level

Controller with sufficient nos. of low / high level alarms, contacts with

electrodes and control wiring for the automatic operation of all water

supply pumps to achieve the functional requirement shall be

provided. Control wiring between these pumps and water tanks shall

be provided. Raw water pumps must start at low level of water in

49 underground domestic water tank & stop at high water level in that

tank. Dry running protection shall be provided for all the pumps.All

water supply to operate automaticaly through level controller.

(a) Capacity 1 LPS each minimum

RPM 2800 / 2 HP

SUBMERSIBLE SUMP PUMPS FOR PLANT ROOM DRAINAGE

(Location : Basement of the Building)

Supplying, Installation, Testing & Commissioning of dewatering

single stage submersible non clog type (Capable of solid handling of

20 mm diameter) self priming of suitable HP pump with casing in

SS., Impeller in SS & shaft in SS with auto level controls (to stop at

Low Level and to Start at High Level in the sump) having discharge

of 250 LPM at 12 Mtr head complete with all accessories suitable for

operation on 230 Volt 3 phase 50hz AC supply as required for plant

room. The pump shall be inclusive of strainer, sluice/gate valve, non

return valve, float switch,...Etc

Flow Rate =250 LPM

HP - as per maufacturer recommendations.

Quantity (Set=1 Working + 1 Standby)

Control panel, configuration with all standard feature like , contactor

,relays, MCB Tp, Amp-meter, volt meter, single phase / Three phase

preventer , over load, dry run protection, Start, Stop, Indicators, Auto,

manual, Sequential, timer etc. all of reputed make like: L&T/

Installation testing & commissioning of pump

Cable 2x 1.5 squire mm (Supply and lying /Terminating).

Ø 50mm GI pipe (Make Pipe JINDAL/SURYA) with Ø50 mm 1No

Ball valve, 1 No NRV Ø 50mm. (Make: SANT/ZALOTO).

Contractor 54 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Providing and Fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A, including jointing with seal

ring conforming to IS: 5382, leaving 10mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised PVC moulded fittings/

accessories for unplasticized Rigid PVC rain water pipes conforming

52 12.42 to IS : 13592 Type A, including jointing with seal ring conforming to

IS: 5382, leaving 10mm gap for thermal expansion.

12.42.1 Coupler

12.42.6 Shoe (Plain)

Providing and fixing unplasticised PVC pipe clips of approved design

to unplasticized PVC rain water pipes by means of 50x50x50 mm

hard wood plugs, screwed with M.S. screws of required length,

including cutting brick work and fixing in cement mortar 1:4 (1

cement : 4 coarse sand) and making good the wall etc. complete

Providing and fixing to the inlet mouth of rain water pipe cast iron

54 12.44 grating 15 cm diameter and weighing not less than 440 grams Each 20 54.70 1094.00

Providing, laying and jointing glazed stoneware pipes class SP-1 with

55 19.1 stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1

fine sand) including testing of joints etc. complete :

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

sand : 10 graded stone aggregate 40 mm nominal size) all-round

S.W. pipes including bed concrete as per standard design :

a 19.2.2 150 mm diameter S.W. pipe meter 160 1179.85 188776.00

b 19.2.3 200 mm diameter S.W. pipe meter 160 1375.45 220072.00

Contractor 55 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2023/ DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

MR All Figure are in Rs. All Figure are in Rs.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

sand : 10 graded stone aggregate 40 mm nominal size) up to

haunches of S.W. pipes including bed concrete as per standard

a 19.3.2 150 mm diameter S.W. pipe meter 160 743.10 118896.00

b 19.3.3 200 mm diameter S.W. pipe meter 160 873.50 139760.00

Providing and laying non-pressure NP2 class (light duty) R.C.C.

pipes with collars jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement : 2 fine sand) including testing of joints

etc. complete :

Supply, Installation, Testing and Commisioning of Sensor based

basin mixer wall mounted. LPM should be 2.5 with suitable aerators

as per GRIHA norms. Manufacturer should have valid GRIHA

Supply, Installation, testing and Commisioning of Touch free infrered

Supply, Installation, testing and Commisioning of Automatic soap

Supply, Installation, Testing and Commisioning of Toilet Paper

Holder with flap

Supply, Installation, Testing and Commisioning of Wall Mounted

Paper Towel Dispenser

Supply, Installation, Testing and Commissioning of Electromagnetic

Flow Meter/ Water Meter having the following specs suitable for

pipes upto 50 mm dia pipes:

Transmitter: Die Cast

Power Supply: 90 – 265 VAC

Outputs: 4-20 mA , Pulse, RS485

64 MR Process Pressure: 10 Bar each 4 25300.00 101200.00

Sensor Terminal Housing: C.S

Fabricated IP65

Display: Remote Display With 5

Flange: ASA #150 C.S

Electrode: SS316L

Grounding Electrode: SS316L

Flow Tube: SS304

Coil Housing: C.S

Protection Class: IP-66

Contractor 56 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: HVAC

S No Description Unit Quantity Rate DSR NON-DSR

All Figure are in Rs. All Figure are in Rs.

VRF OUTDOOR UNIT: Supply, Installation, Testing & Commissioning of Modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for

cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll

Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP

modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A

Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To

have better efficiency condenser fan shall be capable to operate at different speed with respect to

load. The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and

CPWD Specifications and work even at 50°C ambient temperature without tripping. The system

shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be

1 31.3 suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit

shall be filled with first charge of the refrigerant and ready for use as required. The condenser

should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat

exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving

overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the

unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below

and complete as per CPWD specification, connections, inter connections etc. as required. (For

capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for

Super ECSBC Building)

For Cooling or Heating or Both

VRF INDOOR UNITS: Supply, Installation, Testing and Commissioning of following minimum

capacity High wall type Indoor unit equipped with and comfort washable synthetic media pre-filter,

fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with

DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan,

necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC

2 31.8 supply, complete as required. The Indoor units must shut down upon receiving a singal from the

BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27

Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Contractor 57 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: HVAC

S No Description Unit Quantity Rate DSR NON-DSR

All Figure are in Rs. All Figure are in Rs.

Supply, Installation, Testing and Commissioning of following minimum capacity Single way wall/corner

VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter,

fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper

coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation,

3 31.6 Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC

supply,complete, as required. The Indoor units must shut down upon receiving a singal from the BMS

System/Fire Signals. The system shall be capable to adjust air flow as per room requirement

automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature. (Make will be same as of Outdoor)

INDOOR UNIT Supply, Installation, Testing and Commissioning of following minimum capacity 4 way

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section

with low noise fan /dynamically balanced blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation,

4 31.4 Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply,

complete, as required. The Indoor units must shut down upon receiving a singal from the BMS

System/Fire Signals. The system shall be capable to adjust air flow as per room requirement in auto

mode. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree

C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original

Equipment Manufacturer (OEM) make as of ODUs and IDUs

b 31.13.2 Outdoor Multi Joint Nos 12 8,098.00 97,176.00

REFRIGERANT PIPING:

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following

nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings,

with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with

XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves

sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per

specifications etc. as required:

Contractor 58 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: HVAC

S No Description Unit Quantity Rate DSR NON-DSR

All Figure are in Rs. All Figure are in Rs.

a 31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 500 256.00 128,000.00

b 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 1675 346.00 579,550.00

c 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 500 487.00 243,500.00

d 31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Metre 1675 615.00 1,030,125.00

e 31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 400 739.00 295,600.00

f 31.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 400 904.00 361,600.00

g 31.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 300 1,068.00 320,400.00

h 31.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Metre 300 1,157.00 347,100.00

i 31.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 100 1,222.00 122,200.00

j 31.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 100 1,286.00 128,600.00

k 31.14.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 50 1,322.00 66,100.00

l 31.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Metre 50 1,368.00 68,400.00

a MR 300x75mm outdoor cable tray with cover (hot dip galvanized) Metre 700.00 1,439.00 1,007,300.00

DRAIN PIPING For VRV HVAC

8 Providing and fixing of uPVC/cPVC/PVC drain pipe

CONTROL CABLING

Supplying, receiving, storing, laying, effecting proper connections, testing and commissioning of the

9 following sizes of 1.1 KV grade PVC insulated copper conductor unarmoured stranded control cable

complete as required.

a MR 2C x 1.5 mm² Cu (Communication cable from ODU to IDU for VRF units) Metre 2610 274.00 715,140.00

Supply, Installation, Testing & Commissioning of Silent type circular /rectangular inline fans for exhaust air

complete with sheet metal casing, 25mm thick acoustic insulation, direct driven centrifugal fan, motor with

proper protection and inspection door. Fan shall be suitable for operation on 220+6 % volts, 50 Hz,1

phase AC power supply. Flanges to be provided on both sides to facilitate duct connections. Fan shall be

10 installed as shown in the drawings and will be of following characteristics:

MR All single phase inline fans shall be provided with factory fitted speed regulators. All Fans Should be

complete with Plug Top & necessary power cable.

Fans shall have low noise level in rage of 35-40dBA @3m and shall be suitable for indoor installations.

a 200 CFM S P of 13-14 for Toilet Nos. 24 6500.00 156000.00

b 500 CFM S P of 13-14 for Kitchen Nos. 2 9500.00 19000.00

Contractor 59 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: VENTILATION

DSR E&M DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

All Figure are in Rs. All Figure are in Rs.

1 Exhaust Fans - Axial Flow Type :

( Fire rated : 250 deg for 2 Hrs. )

Providing, fixing, testing and commissioning of AMCA Certified (For Air and Sound

Performance) tube / vane axial flow fan of different capacity as mentioned below in standard

M.S. construction. Entire fan model & AMCA Seal shall appear in technical submittal of fan. All

the fans are synthetic enamelled painted/hot dip galvanized with minimum 220 GSM Zinc

Coating and complete with bird screen at inlet. The electric motor coupler shall be squirrel cage

induction motor (IE-3 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be

MR of high temperature resistance "Class H Smoke Spill" 250° C for 2 hrs. Fan shall be TUV / CE

Certified for high temperature. Fan shall be EN 12101-3 Certified high temperature. Motor

should be VFD rated. Fan efficiency should not be less than 70 %. Noise level should not more

than 80 dB @ 3 mtr distance when measured in hemispherical reverberant room conditions,

for normal (non-fire) conditions, and not more than 85 dB @ 3mtr distance for fire conditions.

Fans should be as per specification and drawings.

(i) Normal Mode

(ii) Emergency Mode

2 Lift well Pressurization Axial fan

Supply, installation, testing and commissioning of Direct drive Tube Axial fans complete with

Hot dipped Galvanised Steel Casing with spun flanges, adjustable pitch die cast aluminium

impeller (Hub and Aerofoil blades) and IE3 motors. Casing position shall be as per the

MR job requirement and shall be marked on the fan assembly.The complete fan

assembly with its casing, impeller and motor ( not only motor or one of the item ) shall be

sourced from one manufacturer. Fan mut be AMCA certifeid for Air & sound both

3 Lift Lobby Pressurization Axial fan

Supply, installation, testing and commissioning of Direct drive Tube Axial fans complete with

Hot dipped Galvanised Steel Casing with spun flanges, adjustable pitch die cast aluminium

impeller (Hub and Aerofoil blades) and IE3 motors. Casing position shall be as per the

MR job requirement and shall be marked on the fan assembly.The complete fan

assembly with its casing, impeller and motor ( not only motor or one of the item ) shall be

sourced from one manufacturer. Fan mut be AMCA certifeid for Air & sound both.

Supplying, installation, balancing and commissioning of fabricated at site GSS sheet metal

rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

4 30.12.2 vanes, hangers, supports, bends, transitions, reducers, end caps, collars etc as required

complete in all respect in confirmation with IS : 655 and approved drawings and specifications

of following sheet thickness complete as required.

Contractor 60 Digitally signed byNBCC

Tender for appointment of Contractor for "Construction of Central Bank of India Office Building at Amaravati, Andhra Pradesh"

SCHEDULE OF QUANTITIES: VENTILATION

DSR E&M DSR NON-DSR

S NO DESCRIPTION UNIT QTY RATE

All Figure are in Rs. All Figure are in Rs.

Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI

volume control damper with enthalpy sensor and necessary control wire for integration within

5 30.14 AHU room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in

confirmation to SMACNA/IS and as per specifications complete etc. as required.

Supplying, Fixing, installation, testing and commissioning of powder coated extruded SQM 20 9,623.00 192,460.00

6 30.15 aluminium Supply Air Grills with aluminium volume control dampers in confirmation to

SMACNA/IS and as per specifications complete etc. as required.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but SQM 20 6,285.00 125,700.00

7 30.16 without volume control dampers complete in confirmation to SMACNA/IS and as per

specifications complete etc. as required.

Electrical Panels

Supplying ,testing and commissioning of combined sheet steel cubicle type panels fabricated

from 14 guage thick CRCA sheet, dust and vermin proof, indoor type Panels with hinged

lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz

AC supply with rear / bottom access for cable alley and with segregated bus-bar chamber and

including supplying and fixing following switchgears, meters and accessories, inter-connections,

bonding to earth, bottom base channel of MS. Entire panel shall have a common earth busbar

at rear with 2 nos earth stud cable alleys, cable gland plates powder coated painting of

approved shade after antirust treatment and marking as specified. Switch boards complete as