Construction of School of Tourism Studies at Muttom Campus for MG University Kottayam

Amount

Laying and Jointing PVC Pipe. Heading

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

2.7.3 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (blasting prohibited)

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.9.1 : Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock

2.9.3 : Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Hard rock (blasting prohibited)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.26.2 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.32 : Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.2.5 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

4.11 : Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

4.12 : Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification .

4.13 : Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

4.15 : Extra for laying concrete in or under water and or liquid mud including cost of pumping or bailing out water and removing slush etc. complete. Note for item No. 4.15 : - The quantity will be calculated by multiplying the depth measured from the sub-soil water level upto centre of gravity of concrete under sub-soil water level with quantity of concrete in cum executed under the sub-soil water. The depth of centre of gravity shall be reconed correct to 0.10 m 0.05 m or more shall be taken as 0.10 m and less than 0.05 m ignored.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and walls Under 20 cm wide

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.12 : Providing, hoisting and fixing up to floor level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone - III) : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

6.15 : Extra for providing and placing in position 2 Nos 6 mm dia M.S bars at every third course of half brick masonry.

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.5 : Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

9.5.1.1 : Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge.Second class teak wood35 mm thick shutters

9.7.1 : Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:Second class teak wood

9.12 : Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. ( Area of opening for glass panes excluding portion inside rebate shall be measured).

9.14 : Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. ( Shutter area to be measured)

9.21.1 : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative Type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

9.23 : Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.74.1 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:250x10 mm

9.74.2 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:200x10 mm

9.74.3 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:150x10 mm

9.75.2 : Providing and fixing bright finished door latch with necessary screws etc. complete:250x16x5 mm

9.77 : Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete

9.81.1 : Providing and fixing bright finished brass handles with screws etc. complete:125 mm

9.82 : Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.96.1 : Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:300x16 mm

9.96.2 : Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:250x16 mm

9.102 : Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

9.103 : Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc . complete.

9.118.3 : Providing and fixing to existing door frames25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm x 25 mm or less as per requirement with and average wall thickness of 1 mm ( ± 0.3 mm). PVC foam end cap of size 23x10 mm area provided on both vertical edges to ensure the overall thickness of 25 mm. An M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end -cap of the size 25 mm x 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer,s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places.

9.119 : Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door fame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer-in Charge.

9.139 : Providing and fixing panic bar / latch (Double point ) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer -in-charge, all complete.

9.161 : Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontalside & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mmthick GI sheet ( Zinc coating not less than 120gm/m2) suita2ble for mounting 120min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineralwool Insulation having density min 96Kg/m2 . The frame will have a provision ofG.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style ofsize M10 x 80 ) suitable for fixing in the opening along with Factory madeTemplate for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire ratedglazed shutter . The frame shall be finished with a approved fire resistant primeror Powder coating of not less than 30 micron in desired shade as per thedirections of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded

9.162 : Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minFire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certifiedas per laboratory approved by Engineer-in-charge, with suitable mounting ondoor frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mmwide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet(zinc coating not less than 120gm/m²) duly filled mineral wool insulation havingdensity min 96 kg/m³ and fixing with necessary stainless steel ball bearing hingesof size 100x89x3mm of approved make, including applying a coat of approvedfire resistant primer or powder coating not less than 30 micron etc all completeas per direction of Engineer-in-charge (panelling to be paid for seperately

9.164 : Providing and fixing glazing in fire resistant door shutters, fixed panels & partitionsetc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mmfrom the edges and 150 mm c/c , including applying a coat of approved fire resistantprimer/powder coating of not less than 30 micron on G.I. beading, & special ceramictape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-incharge.The glass shall be clear, toughened, interlayered, non-wired fire resistant having11 mm thickness of approved brand with 120 minutes of fire resistance both integrity &radiation control (EW120) and minimum 15 min of insulation (EI15) and having a soundreduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category ofImpact Resistance as per EN 12600. The glass should be manufactured in UL & TUVaudited Facility and including UL-EU Certification.The maximum glazing size cannotbe more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report forthe complete system (Glazed Door or Partition) will be considered valid only if it containsthe stamp and signature of the authorized signatory from the glass manufacturer.(Actual glass size is to be measured at site for payments).

9.165.1 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

10.7 : Providing and fixing ball bearing for rolling shutters.

10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges (area of grill to be measured).

10.17 : Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

10.27.1 : Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide P A 6 grade sleeve, including drilling of hole in frame, concrete/masonry, etc. as per direction of Engineer-in-charge.10 x 60 mm

11.4 : 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete

11.6.1 : Cement plaster askirting upto 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement .18 mm thick

11.36 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.41.3 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x 800 mm

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.46.3 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 800 x 800 mm

11.47.2 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

12.45.1 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

12.45.4 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:Fully Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

12.52.3 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.12.5 mm thick square edge PVC Laminated Gypsum Tile size 595x595 mm made of Gypsum plasterboard , manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyster on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyster film so as to make the tile a completely sealed unit.

12.52.4 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.12.5 mm thick fully Perforated Gypsum Board tile made from plaster board having glass fibre conforming to IS: 2095 Part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with centre borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side , having as NRC ( Noise Reduction Co efficient) of 0.79, with 50 mm resin bonded glass wool backing.

13.1.2 : 12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand).

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.21 : Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.47.1 : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

14.70 : Melamine polishing on wood work ( one or more coat)

15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

19.18.3 : Supplying and fixing C.I with out frame for manholes:560 mm diameter ( heavy duty) the weight of the cover to be not less than 108 kg

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

21.12.2 : Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with S.S. screws etc. complete as per direction of Engineer -in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar

21.15.1 : Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary necessary screws etc. complete.Anodized (AC 15 ) aluminium

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.22A : Providing and applying fibre reinforced elastomeric liquid water proofing membranewith resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top ofconcrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming ofelastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and twocoats of undiluted elastomeric waterproofing liquid (dry film thickness of completeapplication/system not less than 500 microns). The operation shall be carried outafter scrapping and properly cleaning the surface to remove loose particles withwire brushes, complete in all respect as per the direction of Engineer-in-Charge.

22.23A : Providing & Applying polymer modified, flexible cementatious negative sidewaterproofing coating with elastic waterproofing polymers on interior wall plastersurface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatiouswaterproofing polymer(dilution with water in the ratio of 1:1) and two coats ofcementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) afterscrapping and properly cleaning the surface to remove pre-existing paint film &loose particles till plaster is visible, complete in all respect as per the direction ofEngineer-in-Charge.

22.26 : Providing and applying of swellable type water stop tape, 19mm x 25mm thick inlinear meter (expansive nature) for construction joints treatment of RCC structuresuch as raft slab, retaining walls, water storage tank and at the junctions of raftslab with the retaining walls etc.. After cleaning the surface, one coat of requiredprimer for swellable water stop tape shall be applied throughout the length of thejoint @3.78 litre per 240 running meter. Over the primed surface swellable typewater stop tape shall be placed. The work shall be carried out all complete as perspecification and the direction of the engineer-in-charge. The product performanceshall carry guarantee for 10 years against any leakage.

23.5 : Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer -in- charges

23.6 : Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit,over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer -in-Charge

23.7 : Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

25.1 : Providing and supplying aluminium extruded tubular and other aluminium sectionsas per the architectural drawings and approved shop drawings , the aluminiumquality as per grade 6063 T5 or T6 as per BS 1474,including super durable powdercoating of 60-80 microns conforming to AAMA 2604 of required colour and shadeas approved by the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extruded aluminiumframe work. Nothing extra shall be paid on this account).

25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi(grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including:a) Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof testat 1.5 times design wind pressure without any failure), including functional designof the aluminum sections for fixing glazing panels of various thicknesses, aluminiumcleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmokeseals, microwave cured EPDM gaskets for water tightness, pressureequalisation & drainage and protection against fire hazard including:b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3Dimentional movement for achieving perfect verticality and fixing structural glazingsystem rigidly to the RCC/ masonry/structural steel framework of building structureusing stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetalliccontacts with nuts and washers etc. of stainless steel grade 316, of the requiredcapacity and in required numbers.c) Providing and filling, two part pump filled, structural silicone sealant and onepart weather silicone sealant compatible with the structural silicone sealant ofrequired bite size in a clean and controlled factory / work shop environment ,including double sided spacer tape, setting blocks and backer rod, all of approvedgrade, brand and manufacture, as per the approved sealant design, within and allaround the perimeter for holding glass.d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thickand of sizes, shapes and profiles, as required as per the site conditions, to seal thegap between the building structure and all its interfaces with curtain glazing tomake it watertight.e) Making provision for drainage of moisture/ water that enters the curtain glazingsystem to make it watertight, by incorporating principles of pressure equalization,providing suitable gutter profiles at bottom (if required), making necessary holesof required sizes and of required numbers etc. complete. This item includes costof all inputs of designing, labour for fabricating and installation of aluminium grid,installation of glazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes or cradles etc.as described above and as specified. The item includes the cost of getting all thestructural and functional design including shop drawings checked by a structuraldesigner, dully approved by Engineer-in-charge.The item also includes the cost of all mock ups at site, cost of all samples of theindividual components for testing in an approved laboratory, field tests on theassembled working structural glazing as specified, cleaning and protection till thehanding over of the building for occupation. In the end, the Contractor shall providea water tight structural glazing having all the performance characteristics etc. allcomplete as required, as per the Architectural drawings, as per item description,as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extrudedaluminium section capping for fixing in the grooves of the curtain glazing andvermin proof stainless steel wire mesh shall be paid for separately under relevantitems under this sub-head. However, for the purpose of payment, only the actualarea of structural glazing (including width of grooves ) on the external face shallbe measured in sqm. up to two decimal places.Note:-2. The following performance test are to be conducted on structural glazingsystem if area of structural glazing exceeds 2500 Sqm from the certified laboratoriesaccreditated by NABL(National Accreditation Board for Testing and CalibrationLaboratories), Department of Science & Technologies, India. Cost of testing ispayable separately. The NIT approving authority will decide the necessity of testingon the basis of cost of the work, cost of the test and importance of the work.Performance Testing of Structural glazing systemTests to be conducted in the NBL Certified laboratories1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to+300pa) as perASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testingmethod for a range up to 2000 ml.”3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testingmethod for a range upto 2000 ml”4. Structural Performance Deflection and deformation by static air pressure test(1.5 times desing wind pressure without any failure) as per ASTME-330-10 testingmethod for a range upto 50 mm”5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method forQualitative test” Tests to be conducted on site6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi)upto 2000ml”

25.3 : Providing, assembling and supplying vision glass panels (IGUs) comprising ofhermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel unitsof size and shape as required and specified, comprising of an outer heatstrengthened float glass 6mm thick, of approved colour and shade with reflectivesoft coating on surface # 2 of approved colour and shade, an inner Heat strengthnedclear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primaryseal and secondary seal (structural silicone sealant) etc. all complete for the requiredperformances, as per the Architectural drawings, as per the approved shopdrawings, as specified and as directed by the Engineer-in-Charge. The IGUs shallbe assembled in the factory/ workshop of the glass processor. (Payment for fixingof IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment,only the actual area of glass on face # 1 of the glass panels (excluding the areas ofthe grooves and weather silicone sealant) provided and fixed in position, shall bemeasured in sqm.(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating onface # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved makehaving properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflectioninternal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performanceglass shall be decided by technical sanctioning authority as per the site requirement

25.4 : Extra for openable side / top hung vision glass panels (IGUs) including providingand supplying at site all accessories and hardwares for the openable panels asspecified and of the approved make such as heavy duty stainless steel frictionhinges, min 4 -point cremone locking sets with stainless steel plates, handles,buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts,washers etc. all complete as per the Architectural drawings, as per the approvedshop drawings, as specified and as directed by the Engineer-in-Charge.

25.5 : Providing,fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi - rigid, inorganic, non- combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5mm and nominal mass not less than 60 gm/ sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts,bolts, washers etc complete.

25.6 : Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc., all complete for the required performance as specified, as per the architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in - Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass panels in the curtain glazing is included in cost of relevent item*).(ii) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face #2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35%, Light reflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25 - 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

50.2.26.1 : Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

50.6.1.4 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.6 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

50.6.2.1 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.6.3.1 : Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth for 10 cm thick wall in CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

50.12.2.5 : Providing & fixing Poly carbonate multi wall plain sheet 8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size ( 5.5x55mm) with EPDM seal complete upto any pitch in horizontal /vertical / curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

od264030/2019_2020 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. All work upto plinth level

od264031/2019_2020 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Minimum Cement content considered in this item is @ 330 kg/ cum. All work above plinth level upto floor V level

od264034/2019_2020 : Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

od264035/2019_2020 : Steel work welded in built up sections/framed work including cutting hoisting, fixing in position and applying two coats of approved make and colour synthetic enamel paint over two coats of approved make anticorrossive yellow zinc chromate primer, etc. including cost and conveyance of all materials, labour, lead,lift etc. complete as directed by Engineer- in-Charge at all levels. In stringers, treads, landings etc of staircases including use of chequered plate wherever required, all complete

od264038/2019_2020 : Providing ,hoisting and fixing upto floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, slabs,brackets etc. including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 Cement : 3 fine sand) on exposed surfaces complete but excluding the cost of reinforcement with design mix cement concrete of M-25 grade conforming to IS 456 or IS 10262.

od264039/2019_2020 : Steel work welded in built up sections/framed work including cutting hoisting, fixing in position and applying two coats of approved make and colour synthetic enamel paint over two coats of approved make anticorrossive yellow zinc chromate primer, etc. including cost and conveyance of all materials, labour, lead,lift etc. complete as directed by Engineer- in-Charge at all levels. In gratings, frames, guard bar, ladders, railings, brackets, gates similar works.

od264040/2019_2020 : Providing and laying Anti-skid Ceramic floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

od264042/2019_2020 : Providing and applying Antitermite treatment by injecting chemical emulsion Imidacloprid emulsiable concentrate .075% for pre-constructional treatment and creating a chemical barrier as per IS 6313 (Part II) 2001 for wall trenches, foundation, top surface of plinth filling, foundation of wall and floor, along the external perimeter of the building, etc. complete conforming to manufacturers specification and as directed by the Engineer-in-Charge. (Plinth area only to be measured for the payment )

od264044/2019_2020 : Supplying and fixing C.I. cover with frame for manholes :600x600 mm square C.I. cover (light duty) the weight of the cover to be not less than 32 kg. Complete all works including cost and conveyance of all materials, all labour charges,lead, lift, sundries, etc., complete. as directed by the Engineer- in-Charge

od264046/2019_2020 : Steel work in built up tubular sections YST 310 grade as per IS: 4923 including cutting, bending, hoisting, fixing in position, welded and bolted including special shaped washers etc. complete with electric resistance or induction butt welded tubes including painting with two coats of approved make and colour synthetic enamel paint over two coats of approved make anticorrossive yellow zinc chromate primer, closing all the open ends properly with same material cost and conveyance of all materials, labour, etc., complete as directed by the Engineer-in-Charge at all levels.

od264048/2019_2020 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level up to floor five level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

od264053/2019_2020 : Supplying and fixing rolling shutters of approved make,made of required size M.S laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets,side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire springs grade No.2 and M.S top cover of required thickness for rolling shutters including two coats of approved make and colour synthetic enamel paint over two coats of approved make anticorrossive yellow zinc chromate primer, including cost and conveyance of all materials, labour charges,lead,lift etc complete as directed by Engineer in Charge at all levels. 80 X 1.25 mm M.S.Laths with 1.25mm thick top cover

od266485/2019_2020 : Providing and fixing steel (white power coated) crescent lock for uPVC /aluminum sliding window/ door with necessary screws etc. complete.

od267060/2019_2020 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer and epoxy paint . G.I. pipes

od268608/2019_2020 : Extra rates for excavation in or under water and/or liquid mud, including pumping out metre water as required. ( 20 % of respective earthwork considered) - All kinds of Soil.

od268610/2019_2020 : Supplying and fixing C.I. cover with frame for manholes : 600x600 mm square C.I. cover (Heavy duty) the weight of the cover to be not less than 210 kg. Complete all works including cost and conveyance of all materials, all labour charges,lead, lift, sundries, etc., complete. as directed by the Engineer- in-Charge

od268611/2019_2020 : 15mm cement plaster of mix, 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement 2 kg/sqm( including mixing water proofing material separately )proportion recommended by manufacturer at all heights including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer in charge at all levels. (water proofing liquid will be paid separately)

od268612/2019_2020 : Providing and constructing soak pit 2 m x 2 m x 2 m size with honey comb brick work on the sides upto a height of 1.2 m and brick masonry in CM 1:6 for the balance height,providing and filling brick bats graded, upto a height of 1.7 m,providing and laying precast slab(1:1.5:3) over the pit supporting on the brick work, including cost and conveyance of all materials,labour charges, lead, lift, etc. complete as directed by the Engineer-in-charge.

od268719/2019_2020 : Supplying And Fixing BTS 80 or equivalent Floor spring ,Top patch , bottom patch , Top pivot , and corner lock for Frameless glass door with 60mm EPC - both side key , all complete as per approved drawings and as directed by Engineer in charge

od268727/2019_2020 : Supply and Installation of Handles TGDIH 450 X 25 for Glass Door of Stainless Steel Satin Finish, SS 304 Back To Back Pull Handles Dia. 25 mm,CTC Length 350 mm all complete, as per approved drawing and as directed by Engineer in charge.

od268734/2019_2020 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock , stopper top bottom pivot spring etc to be paid separately)

od268893/2019_2020 : Supplying and Fixing Movable Wall(comprising of 12 panels) 52 dB,R W Sound rating (Laboratory tested) fitted with necessary Hardware and acoustic material packed together with Medium Density Fibre board (MDF). Standard Panel and Expanding Panel of thickness -100 mm with 16mm Thick MDF on both sides with side Stacking. Total No .of panels-12 including the Expanding Panel; each approximately 1089 mm Wide. and 3 metre height as per manufacturers specification and as directed by engineer in charge..The rate shall be inclusive of 12 number of approved panels including instalation,all lead,lifts,scaffolding ,accessories etc complete and measurement shall be done for complete movable wall and not for individual panels. .

od269147/2019_2020 : Providing and applying Synthetic Fibre plaster RENOVO or equivalent of approved colour, shade and pattern on external wall over the base plaster in cement mortar, including providing necessary grooves and painting the plastered surface to give a neat and uniform finish at all floors, inclusive of the cost of materials labour and scaffolding for executing the Renovo plaster all as per manufacturers specifications and as directed by the Engineer-in-charge. The base plaster in cement mortar will be paid for separately.

od269275/2019_2020 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Double charged Vitrified tiles of size 600 x 600 mm.

od269279/2019_2020 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Anti Skid Germ Free vitrified Tiles of Size 600 x 600 mm.

od269291/2019_2020 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement matching pigments etc. complete. Double Charge Vitrified Tiles of Size 600x600 mm

od269339/2019_2020 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement matching pigments etc. complete. Anti Skid Germ Free Vitrified Tile of Size 600x600 mm

od269357/2019_2020 : Providing and laying Heavy Duty Vitrified tiles 20 mm thick of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Heavy Duty Vitrified Tile of Size 600 x 600 mm.

od269374/2019_2020 : Providing and fixing onto staircase steps/landings, ready made heavy duty vitrified step tiles of size 300 x 1200mm / 600x1200 or slabs 15mm thick combinations of different colours as directed by the Engineer in charge over 20 mm thick cement mortar base with cement mortar1:4(1cement :4 coarse sand) etc., complete. Tiles of Size : 300 x 1200 mm ( tread)

od269448/2019_2020 : Providing edge moulding to tile work in flooring and skirting etc., including machine/ hand polishing,moulding or rounding to edge to give smooth finish etc. complete as per design approved by Engineer -in-Charge.

od270956/2019_2020 : Extra for providing vision panel in all type of flush doors (cost of glass excluded ) (overall area of door shutter to be measured): Rectangular or square

od271051/2019_2020 : Providing and Laying water proofing on external surface of retaining wall and base using minimum 1.2 mm thickness HDPE membrane of approved make confirming to the requirements of DIN EN 1849-1 for thickness with a puncture resistance of >220 N as per ASTM E154 including cleaning the surface, priming the surface with cold applied bituminous primer. The membrane should be sealed properly at joints & maintaining 75 mm overlap between the membrane selvedge & 100 mm overlap on the end joints of the membrane over the surface etc.. complete, with 10 years warranty for waterproofing performance to be given by the principal manufacturer for both supply and application all complete as per manufacturer specification and the direction of the engineer-in-charge.

od271052/2019_2020 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With float glass panes of minimum 5mm thickness

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 x 1.5 sq.mm + 1 x1.5 sq.mm earth wire

2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire

2 x 4 sq.mm +1 x 4 sq.mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/CMS/Floor trunking etc as required.

3 x 1.5 sq. mm

3 x 2.5 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mm x 75mm)

3 Module (100mm x 75mm)

4 Module (125mm x 75mm)

6 Module (200mm x 75mm)

Supplying and fixing following Modular base and cover plate on existing modular metal boxes/PVC boxes/furniture cut outs/CMS etc as required

1 or 2 Module

3 Module

4 Module

6 Module

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing suitable size GI box for surface application with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supply and fixing 3 pin, 6A ceiling rose on the existing junction box / wooden block including connection etc as required.

Installation, testing and commissioning of pre-wired, fluorescent/LED fitting/compact fluorescent/LED fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall/false ceiling/hanging/pendandt type, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan upto 450mm in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Supplying and fixing brass batten/ angle holder including connections etc. as required.

Providing and fixing plain 16/0.20 mm (0.50 sq.mm) twin circular flexible FRLS PVC insulated, PVC sheathed copper conductor cable direct on the wall with PVC clips etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB,“C” curve including connections, painting etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

MCB, SWITCHGEARS & DBs Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way double door

8 way double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (4 + 12), Double door

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Triple pole

Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and fixing Cable End Box (Loose wire box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

EARTHING Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50 mm)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

MV & HT CABLE LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the exisitng RCC/Hume/Metal pipe as required.

Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/ 40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.l. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

HT CABLE LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size in the existing masonry open duct as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size in the existing RCC/HUME/ METAL pipe as required.

Above 120 sq. mm and upto 400 sq. mm

MV CABLE JOINTING & END TERMINATION Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3.5cx300 sq.mm

3.5cx240 sq.mm

3.5cx150 sq.mm

3.5cx120 sq.mm

3.5cx70 sq.mm

3.5cx35 sq. mm

4cx16 sq mm

4cx10 sq mm

2c X 10 sq. mm

2cx6 sq mm

3cX185 sq mm

MISCELLANEOUS ITEMS Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor with day light dimming(lighting level shall be regulated as per availability of natural day light in an area along with occupancy detection.) having high preformance, regulating programmable type, suitable for connected load upto 10 A, for mounting height up to 2.8 meter and for 5 meter diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

Supply and installing of DG exhaust support etc using structural steel work (riveted, bolted or welded) in built up sections, including angle, channel, I section, necessary nut and bolt and all required accessories including cutting, hoisting, fixing in position and applying 2 coats of primer and 2 coats of enamel paint of approved quality etc as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

Providing and fixing M.S. Fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required.

Providing and fixing circular/ Hexagonal GI box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick GI sheet with its top surface hacked for proper bonding, top lid shall be screwed into the GI box by means of 3.3 mm dia round headed screws, one lock at the corners, clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Ordinary Rock

Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

75 mm thick back filling for pitching including supplying of required materials and consolidation etc. complete with :

Stone aggregate 20 mm nominal size

HT PART 250kVA TRANSFORMER

Supply, installation ,testing & commissioning of 250kVA 11kV/433V indoor cast resin dry type USS transformer (copper wound) having a continuous rating for 11kV / 433V 3 phase 50 Hz. Vector group Dyn 11 with off-circuit tapping +5% to -5% in steps of 2.5% by tap links, include separate winding temperature indicator for each phase and core in the Transformer, emergency off switch housed seperately outside. Transformer should have cable end box on HV side suitable for 3Cx185 sq.mm XLPE 11kV cable and suitable end box on LV side for connecting XLPE insulated PVC cables with all accessories, complete as required as per State electricity board, IE rules specifications. The transformer shall confirm to IS 2067/77, 11171/1985 with latest amendment etc complete with HT HRC fuses and output connected to 11KV seal off bushings to the transformer. Supply, Installation, testing and commissioning of Unitised substation with load break switch as primary protection, dry cast resin power transformer, cable end termination facility etc. as follows. HT load break switch fuse unit 630A -1 No. 26.3kA , 630A Aluminium busbar with heat shrinkable insulation and support insulator ( SMC / DMC ) - 1set, Earthing switch interlocked with the main switch - 1 No, Mechanical and electrical on / off indictaion etc

HT CABLE SUPPLY & LAYING

Supply of following 11kV (E) grade XLPE insulated PVC sheathed compact circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in combination with copper tape suitable for 11kV earthed system confirming to relavent standard. 3cx185sq.mm XLPE Cable

Laying of following 11kV (E) grade XLPE insulated PVC sheathed compact circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in separate existing cable tray using factory made clamps and the spacing between clamps will not exceed 60cm. Above 120 sq. mm and upto 400 sq. mm

H.T CABLE TERMINATION

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required. 3C x185 sq.mm.

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required. 3C x185 sq.mm.

TOD METER Supply, Installation, testing & commissioning of 3 phase 4 way 110V (L-L), 5A, class: 0.2, TOD meter with RS485 port, of Electricity board approved make, in existing enclosures of HT Panel including all necessary accessories for fixing and connection complete as required getting tested and approved from statutory authorities, providing connection/inter-connections as required for complete installation and as instructed by Engineer in charge/consultant.

OUTDOOR METERING CUBICLE Supply, erection, testing and commisioning of dust and vermin proof, floor mounted free standing cubicle type 11kV outdoor metering panel box IP67, fully compartmentalised complete with hinged and earthed front doors interlocked with earth switch with provision for TOD metering. Unit shall comprise of 3 nos. CT's of 10VA burden, and class Cl:0.2 and ratio depending on contract demand including fixed type PT of ratio 11kV/110V, 25VA, Cl:0.2 (1 No.) and seal off bushings, space heater with thermostat including 400A Aluminium busbars with support insulators and all other accesories as required for complete installation as required and instructed by engineer in charge/consultant.

2 -POLE STRUCTURE Supply, installation, testing and commissioning of State Electricity board incoming 2 pole structure which consists of required length HT Pre-stressed Concrete Poles (PSC), HT stay set complete, 11kV pin type insulator, channel cross arm, 11kV disc insulator with tension set, earth pipe with clamp ,GI :4mm dia wire, 9kV / 5kA Lighting Arrestor set, 400A Air Break switch with operating handle and locking mechanism, DO fuse set, supports, jumpers, interconnecting conductors and all required accessories complete as per State Electricity board requirements. The cost of the civil foundation not to be considered and shall be measured along with the civil items.

DIESEL GENERATOR SUPPLY & INSTALLATION 250kVA DIESEL GENERATOR

EXHAUST PIPES Supply, erection, commissioning of additional length of exhaust pipes with long radius bend from residential silencer with necessary clamps, fixtures, civil works for support and painted with heat resistant, rust proof, bituminous paint of approved colors to a maximum of 10 m in stages of following sizes including suitable rain cap for top to avoid rain water entry. The distance between exhaust pipe at top and rain cap should be higher than diameter of pipe. It is also recommended that horizontal run of exhaust piping should slope downwards away from engine to the condensate trap. Silencer should be installed with drain plug at bottom. Fixing shall be done with proper clamps, expansion bolts, and all other acessories as instructed by the Engineer and the rate inclusive of all minor civil works required, bolts, clamps etc as required for istallation. Support to exhaust piping should be done in such a manner that load of exhaust piping is not exerted to turbocharger. Exhaust pipe height shall be 3m more than the top of any adjacent building withing 10m radius of the exhaust.

150mm dia

200mm dia

Fabrication, supply & installation of DG adaptor box including all accessories for complete installation including extending of DG bus bar if required,and making ease for providing cable terminations

Supply & providing thermal insulation for silencer with inner glass wool and providing aluminium cladding for 250 kVA DG set exhaust pipe length as per standards.

Supply & providing insulation for exhaust pipe with thermal insulation and providing aluminium cladding as per standards.

Supply, fabricate, handle and erect Fabricated G I duct, complete with all necessary fittings and accessories etc. as reqd. and including supports and necessary fixing components as required for complete installation for DG hot air exhaust

Providing and fixing M.S. grills using suitable sections on to the walls with sufficient bearings on walls including applying a priming coat with approved steel primer and including cost and conveyance of all materials hire and labour charges etc. complete.

DG set commisioning including Trial run of DG set for 6 hrs. on no-load and variable load condition and to record the parameters as per prescribed format as per manufacturer standards. Cost of consumable ( fuel oil, lube oil, etc.) to be borne by Contractor.

LT PANELS

MAIN PANEL Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 14 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. This panel should include Pluggable type surge arrester Class B & Class C/ Class 1 & Class 2 as per IEC 61643 (IP 20) with inbuilt common remote indication for defective arresters 3 nos of encapsulated spark gap & 3 nos of single large block of MOV with series thermal fuse and cooling gel to connect between Line and Neutral and one number arrester encapsulated spark gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, Impulse current-150 KA (10/350µ sec) & 60KA (8/20µ sec) for Line to Neutral & 125 KA(10/350µ sec) for Neutral to Protective Earth, voltage protection level <1.3 KV ( L to N) & <1.3 KV ( N to E). Operating temp -40º to +85ºC. Response time <100 nano sec including necessary HRC fuse for protection of same. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Incomer - EB Incomer - 400A, 36kA EDO Microprocessor based MCCB having isolation duty with 3 O/C and 1 E/F release and standby low set EF relay using CT at neutral earthing conductor. DG Incomer 1 - 400A 36 kA FP EDO Microprocessor based MCCB having isolation duty set and standby low set EF relay using CT at neutral earthing conductor. 400A, ATS with AMF(ASCO) 400A 433V, 36kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement. Multi function digital LED meters with accuracy class 1, with necessary CT and accessories for measuring Voltage, current, kWh, KW, frequency, KVA, kVAr, PF, kVAh, kVArh, Runhours, On hours, Interupts, RPM,Events(High-Low),Neutral current. Phase angle, THD etc. - 2 Nos RYB phase indicating LED lamps with control fuses and switches - 2 set. Surge Protection Device Class B & Class C/ Type 1 & Class 2 and fuse for protection of the same - 2 set Outgoings: 100A 25kA TP Thermal Magnetic Based MCCB - 8 nos, 200A 25kA TP Thermal Magnetic Based MCCB - 2 nos,

COMMON SERVICE PANEL Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable.Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Incomer: 100A FP Isolator - 1 no, 100A 433V, 25kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement, RYB phase indicating LED lamps with control fuses and switches - 1 set Outgoings: 40A TP MCB - 3 nos, 32A TP MCB - 3 no.

LIFT PANEL Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Incomer - 40A FP Isolator - 1 no. 40A, 433V,best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement, RYB phase indicating LED lamps with control fuses and switches - 1 set. Outgoings: 32A FP 100mA FP RCBO - 1 no, 25A DP 30mA FP RCBO - 1 no, 6A SP MCB - 4 nos,

AC Load Bank Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 8 way Load Bank IP43 and quality with corner boxes, cable end boxes, meter module, including busbar, neutral link and DIN bar, bottom add on box for installing surge arrestor device along with fuses with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. SMDB shall be with mounting base for mounting on floor Incomer - 200A FP 25kA thermal magnetic release MCCB -1No., 200A 415V 25kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Prewired meter module including indicating lamps with ammeters and voltmeters CT/PT which is site programmable as per schematic layout. Cable alley - 2 no, Corner box - 4 nos, Bottom add on module for installing surge arrestor - 1 no Outgoings: 63A 16kA TP MCCB, with thermal magnetic releas - 8 nos

STREET LIGHTING PANEL Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Incomer - 32A 100mA FP RCBO - 1 no. 32A,433V,best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement. Astronomical time switch for automatic switching On & OFF of street lights at sun set & sun rise or twilight(Auto ON, Auto OFF, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site - 1no. 32A TP contactor - 1 no. Outgoings:16A DP MCB - 6 nos,

PLUMBING PANEL Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor mounted, front operated MV panel board made out of 16 SWG thick CRCA sheet (7 tank treatment) fully compartmentalised complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Incomer - 32A FP Isolator - 1 no, 32A,433V,best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement, RYB phase indicating LED lamps with control fuses and switches - 1 set. Outgoings: 25A TP MCB -6 nos

CABLES & END TERMINATION LT CABLE SUPPLY Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date.

3.5cx300sq.mm Al Cable

3.5cx240sq.mm Al Cable

3.5cx150sq.mm Al Cable

3.5cx120sq.mm Al Cable

3.5cx70sq.mm Al Cable

3.5cx35sq.mm Al Cable

4x16sq.mm Al Cable

4x10sq.mm Al Cable

4x6sq.mm Al Cable

4x4sq.mm Al Cable

2x10sq.mm Al Cable

2x6sq.mm Al Cable

2x4sq.mm Al Cable

12x2.5sq.mm Cu Control Cable

2cx2.5sq.mm Cu Control Cable

Supply and clamping of the following PVC sheathed unarmoured power cable conductor of best conductivity copper solid/stranded conductor, XLPE insulated, PVC inner sheathed1.1kV grade strictly conforming to IS:1554 (Part-I) 1964 of the following sizes in cable tray /wall using factory made heavy gauge GI/painted MS clamps. Space between clamps not exceeding 60cms amd making good the damages colour washing etc as required. and instructed by engineer at site/consultant.

1Cx10sq.mm Copper Flexible Cable

1Cx6sq.mm Copper Flexible Cable

Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured.

4Cx6sq.mm Al Cable

4Cx4sq.mm Al Cable

2Cx4sq.mm Al Cable

Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required. 6 sq.mm

Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required. 10 sq.mm

Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured. 2Cx2.5 sq.mm Cu Control Cable

Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured. 12Cx2.5 sq.mm Cu Control Cable

LIGHT & FAN FIXTURES

INTERIOR LIGHT FIXTURES Supply of surface mounted LED Batten of wattage 20W. Extruded Aluminium housing with corrosion resistance powder coating using Nano Technology. UV Stabilized diffuser for Optimum light transmission. 4 feet version including all accesories as required for complete installation(Lighting Technologies Wand 24W 5700K LED Commercial Batten light W02457S000 or equivalent)

Supply of surface mounted circular LED Downlighter of wattage 12W. Pressure-die cast Aluminium alloy housing with corrosion resistance powder coating using Nano Technology. Injection moulded UV Stabilized diffuser for Optimum light transmission including all accesories as required for complete installation.(Lighting Technologies Lunar Mid 12W 5700K LED Surface Down light L01257S000 or equivalent)

Supply of recess mounted circular LED Downlighter of wattage 12W. Pressure-die cast Aluminium alloy housing with corrosion resistance powder coating using Nano Technology. Injection moulded UV Stabilized diffuser for Optimum light transmission including all accesories as required for complete installation.(Lighting Technologies Lunar Mid 12W 5700K LED Recess Down Light L01257R000 or equivalent)

Supply of surface mounted circular LED Downlighter of wattage 9W. Pressure-die cast Aluminium alloy housing with corrosion resistance powder coating using Nano Technology. Injection moulded UV Stabilized diffuser for Optimum light transmission including all accesories as required for complete installation.(Lighting Technologies L00957S000 or equivalent)

Supply of recess mounted circular LED Downlighter of wattage 9W. Pressure-die cast Aluminium alloy housing with corrosion resistance powder coating using Nano Technology. Injection moulded UV Stabilized diffuser for Optimum light transmission including all accesories as required for complete installation.(Lighting Technologies Lunar Mid 9W 5700K LED Recess Down Light L00957R000 or equivalent)

Supply of wall mounted LED Batten of wattage 9W for mirror light application. Extruded Aluminium housing with corrosion resistance powder coating using Nano Technology. UV Stabilized diffuser for Optimum light transmission. 2 feet version including all accesories as required for complete installation(Lighting Technologies Wand 09W 5700K LED Commercial Batten light W02457S000 or equivalent)

Supply of LED Square downlight luminaire suitable for surface mount application. The downlighter wattage is 36W. PDC Aluminium alloy housing to facilitate ultra cool performance. White color corrosion resistance powder coating using Nano Technology. Injection moulded PC diffuser for uniform light output, silicon encapsulated high efficency driver including all accesories as required for complete installation. (Lighting Technologies Sparkle surface, S026CTR000+ASS0003 or equivalent)

Supply of LED Square downlight luminaire suitable for recess mount application. The downlighter wattage of 30W. CRCA housing with corrosion resistance powder coating using Nano Technology. UV Stabilized diffuser for Optimum light transmission. Suitable for recess application including frame for flat ceiling if required and all accesories as required for complete installation.(Lighting Technologies Full Lit CR 30W 5700K LED Recess Commercial Light L03057R0C0 or equivalent)

Supply of LED Square downlight luminaire suitable for recess mount application. The downlighter wattage is 15W. Pressure die-cast Aluminium alloy housing with corrosion resistance powder coating using Nano Technology. UV Stabilized diffuser for Optimum light transmission including all accesories as required for complete installation. (Lighting Technologies Dice 15W 5700K LED Recess Sqaure Down Light D01557R000 or equivalent)

Supply of LED luminaire suitable for surface mount application. The luminaire wattage is 30W. Extruded Aluminium housing and PDC endcaps with corrosion resistance powder coating using Nano Technology. UV Stabilized diffuser for uniform distribution. IP65 Protection for both optical and electrical compartment including all accesories as required for complete installation for kitchen application.(Lighting Technologies Amiot 30W 5700K LED Industrial diffused luminaire A03057ID00 or equivalent)

Supply of LED Bulkhead Light Luminaire suitable for Surface/wall mount application. Pressure die-cast Aluminium alloy housing with corrosion resistance powder coating using Nano Technology. UV Stabilized diffuser for Optimum light transmission. 12W 5700K LED including all accesories as required for complete installation. The fixtures shall come with minimum 5 year warranty including all accesories as required for complete installation. (Lighting Technologies LT Star NBT or equivalent)

Supply of LED Wall Light suitable for wall mount application. The luminaire wattage is 12W. High quality synthesis for long lasring durable texture. Consistent chrome finish for uniform shine including all accesories as required for complete installation including all accesories as required for complete installation. Fixture shall include lamp suitaible for connecting in the base including all other accesories required (Philips myliving MLC 30950 or equivalent)

FAN FIXTURES Supplying ceiling fan of 1200mm sweep, including the down rod of standard length (upto 30 cm.) including all accesories as required for complete installation of (havels make, ES 50 White or CG make, Riveria or equivalent).

Supplying of wall fan of 450 mm sweep Havells Airboll Hi-speed or equivalent) including all accessories as required for complete installation.

Supply of exhaust fan of 250mm sweep in the existing opening, as required, including all accessories as rquired for complete installation incluidng shutter etc complete as required.(havells, Ventil Air DX White or equivalent)

Supplying of heavy duty exhaust fan of 450mm sweep in the existing opening, including all accessories as required for complete installation, shutter etc complete as required (Havells, TurboForce SP or equivalent)

PVC BOX Supplying and fixing following size/modules, PVC surface box on surface for modular switches etc as required as instructed by engineer in charge

1 or 2 module

3 module

4 module

6 module

Supplying and fixing following size/modules, PVC flush mounted box, deep mounting box for mounting in furniture cut out/wall trunking for fixing modular baseplate and cover plate for modular switches etc as required as instructed by engineer in charge

1 or 2 module

3 module

4 module

6 module

PVC FLEXIBLE CONDUIT Supply and clamping the following size of corrugated pvc fiexible conduit with necessary locking ring and check nut at termination pointed using suitable size GI/painted MS saddles spacing not exceeding 60 cms on surface including making good the damages, colour washing etc.as required

20mm dia

25mm dia

RCBO Supplying, fixing, testing and commissioning following four pole and double pole , 415 volts and 240 volts, residual current circuit breaker with overload protection (RCBO) of the following rating and sensitivity current in the existing MCB SPN and TPN horizontal/vertical DB's complete with connections, etc. as required and instructed by engineer in charge/ consultant..

16A DP 30mA RCBO

25A 30mA FP RCBO

25A 100mA FP RCBO

32A 100mA FP RCBO

Wiring for Staircase Light Point Wiring for stair case light points with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in and including surface / recessed medium class PVC conduit and all acessories required for complete installation etc , with 1 way modular switch, modular plate, suitable GI box medium class PVC conduit and all acessories required etc and earthing the point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required and instructed by engineer in charge/consultant. (*Note - Staircase light point shall be controlled by a single switch located inside fire control room in ground floor as per latest fire norms)

One light point controlled by one way switch

Loop wiring for Light point

Isolator With Enclosure Supply and fixing of FP CRCA sheet steel powder coated enclosure on surface/recess along with following Amps, 415V, FP isolators confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.

40A FP Isolator with enclosure

63A FP Isolator with enclosure

32A FP Isolator with enclosure

25A FP Isolator with enclosure

Supply, installation, testing and commisioning of following rating TP C curve MCB, 10kA as per IS/IEC 60898-12002 in the existing MCB VDB including all connections and iterconnections as required and as instructed by engineer in charge/consultant.

40A TP MCB

POP - UP BOX

Supply, Fixing, testing and commisisoning of 4 module Matt black finish pop up box with slim design for perfect integration into furniture equipped with one number 6A socket and one number CAT 6 data socket supplied alongwith installation kits for table tops and all accessories as required for complete installation including making good any damages made, as instructed by engineer in charge, providing connections etc as required.

Supply, Fixing, testing and commisisoning of 8(2x4) module Matt black finish pop up box with slim design for perfect integration into furniture equipped with 2 number 6A socket and 1 number CAT 6 data socket & provision for fixing and including one number AV/HDMI socket supplied alongwith installation kits for table tops and all accessories as required for complete installation including making good any damages made, as instructed by engineer in charge, providing connections etc as required.

INDUSTRIAL SOCKETS Supplying, installation, testing & commisioning following surface mounting insulated plug and socket arrangement, power socket in independent position housed in suitable enclosure with high ingress protection (IP 67) with DIN rail for providing RCBO protection of suitable rating , with safe entry for cable and straight plugs with instant locking with screwless clamping, with direct connection with universal screws all terminals facing the same direction with large body size making wiring easy, maximum safety with elongated earth pin disconnected last on removal with direct mounting onto base and maximum cable grip with screwless clamp giving necessary connection as required including all acessories as required for complete installation and as directed by engineer in charge/consultant, and making good any damages made during installation..

MCCB Supply, fixing, testing and commisioning of following rating, breaking capacity and pole, type MCCB in existing Vertical Distribution Board with spreader links, terminal connections and all accesories as required making all necessary connections etc as required and instructed by engineer in charge/consultant.

100 Amp, 16kA, FP MCCB with Thermal-Magnetic Release

SURGE ARRESTOR FOR LOAD BANKS Supply, installation testing & commisisoning of pluggable type surge arrester Class B+C/ Class 1+2 as per IEC 61643 (IP 20),to be fixed in the existing add on module of loadbank with thermal dis connector & provision for inbuilt common indication to identify defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 21 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-90 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) complete with back up fuse of 160A rating HRC fuse unit (4 nos. ) in seperate holder/enclosure suitable for fixing on surface as backup for protection of the arrestor and all accesories as required for complete installation of the same, all connections using Cu flexible cable and interconnections as required. (Distance between arrestor and loadbank shall be kept to minimum as per standard)

SURGE ARRESTOR FOR VDB Supply, installation testing & commisisoning of pluggable type surge arrester in existing Vertical DB in additional DIN bar alongwith the same Class C/ Class 2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E). Lightning Impulse Current – 25 kA(10/350µ sec) for Neutral to EarthNominal discharge current-60 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 120 kA (8/20µ sec)for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth voltage protection level 1400V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E)DIN rail mounting type etc complete and all accesories as required for complete installation of the same.

CABLE MANAGEMENT SYSTEM Supply and fixing of 32 x 12.5 mm PVC Cable Management System with base and lid along with all accessories like external angle, internal angle, flat angle, end cap etc conforming to IEC 61084/ BS 476 & 4678 on surface as required and instructed by engineer in charge/consultant, including all accesories as required for complete installation.

CABLE TRAYS Supply, fabrication at site as per necessary site conditions and fixing of Perforated Cable tray with connectors, horizontal & vertical bends, reducers, Tee's, cross over , anchored din rail suitable supports and brackets and other accessories as required confirming to IEC-61537 and as required for complete installation. The Tray shall be galvanized for corrosion protection confirming to DIN EN 10346 / ISO 1461 .The trays should be tested for a max. safe working load of 150 Kgs with a span distance of 1.5 meters and the deflection should be within the limits as per standard. The safety factor shall be 1.7 times of the safe working load. The perforated tray shall be supplied with the standard length of 3 Mtr. All accesories required for complete installation shall be considered, including bends, hanging supports anchor bolted from ceiling etc. Cable tray routing shop drawing shall got approved from Consultant/Architect before execution at site. Supports shall be placed at minimum distance of 60cm as required. Fabrication works, including welding required for changing of shape, size or offseting of cable trays as per site requirement shall also be considered in this scope. Trays shall be considered with all standard accesories as required like bends, reducers, Tees, cross connectors etc as required (Make OBO Betterman or equivalent). The contractor scope shall include necessary fabrication works for offset of cable, providing radius bends and other joints etc as required as per site conditions and drawings approved and as per the direction of the engineer in charge.

500mm width x 60mm Height

400mm width x 60mm Height

300mm width x 60mm Height

200mm width x 60mm Height

150mm width x 60mm Height

100mm width x 60mm Height

THREE PHASE TO THREE PHASE UPS Supply installation, testing and commissioning of following three phase to three phase UPS indoor (IP20) in stand alone configuration,true online double conversion DSP based UPS system in stand alone configuration with inbuilt parallel kit capable of connecting UPS in parallel mode when required without additional cost, with 15 min backup battery ( battery of reputed make) with, input pf>.99, less input current consumption, with necessary battery circuit breaker., with input 415V, 50Hz three phase, output 240V, IGBT rectifier and IGBT inverter. It shall be 100% generator compatabile with efficiency > 94% and output power factor > 0.9 and including all accessories etc as required. THe UPS system shall be with automatic & manual maintenance bypass switch facility.UPS shall have seperate battery bank, and batteries shall be connected in single string.The system shall comply to IEC /EN 62040-1 and relevant IS standard.The acoustic noise of the system should be less than 58dB.The system shall comply to IEC /EN 62040-1, EN/IEC 62040-2, EN/IEC 62040-3 and relevant IS standard.

20kVA UPS - 1No Battery Circuit Breaker-1No Battery - Required nos. of SMF for providing 15 Minutes Back UP and Battery Accessories like battery rack, interconnecting cables etc.

15kVA UPS - 1No Battery Circuit Breaker-1No Battery - Required nos. of SMF for providing 15 Minutes Back UP and Battery Accessories like battery rack, interconnecting cables etc.

10kVA UPS - 1No Battery Circuit Breaker-1No Battery - Required nos. of SMF for providing 15 Minutes Back UP and Battery Accessories like battery rack, interconnecting cables etc.

LIGHTNING PROTECTION Supply, installation and testing of 2 meter air terminal with accessories: Providing and fixing Air terminals as per IEC -62305 part-3 16mm rod tapered to 10 mm aluminium rod 2 meter rod: Meets the technical specification according to DIN EN 50164-2 (VDE 0815 part 202). Meets the requirement of VDE0185/305(IEC 62305) 101 VL 2000: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. System consist of Fang Fix with base and clamp on the top air terminal is erected. Fang fix clamp made of cable bracket, lightning tested for 100 KA 10/350 micro sec waveform. 16 KG stone of 365 mm diameter, high level of stability. Quick and easy mounting of interception rod using anchors. Concrete, frost-resistant, can be stacked. including all accesories as required for complete installation and as instructed by engineer in charge.

Supply and installation of 8mm solid aluminium round conductor: For concrete building Meets the technical specification according to DIN EN 50164-2 (VDE 0815 part 202). Meets the requirement of VDE0185/305(IEC 62305) RD 8/ALU: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) With 50 sq.mm cross sectional area. Polyamide Conductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance, including all accesories as required for complete installation as instructed by engineer in charge.Price shall be inclusive of conductor holders.

Vertical run- Down conductor

Horizontal run-Parapet application

Supply and fixing of cross connector/T connector: to route vertical down conductor /mesh formation made of stainless steel/hot dipped galvanised iron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts and all accesories as required for complete installation

Supply and fixing of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IEC 62305) and all accesories as required for complete installation

Supply and Fixing Equipotential bonding rail for Lightning Arrestor applications(Test Joint). Equipotential bonding rail for equipotential bonding according to DIN VDE 0100-410/540 and lightning protection equipotetial bonding according to DIN VDE 0185-305. Base plate and cover hood from polystyrene. Colour: Black, UV resistant. Can be used outdoor also. Screw and crossbar made of VA. Capable of carring lightning current 100KA (10/350). Connection options: 7 x single or multi-core conductors to 25mm square or fine core conductors to 16mm square. 1 x round cable Rd 8-10. 1 x flat strip to FL 30 or round cable RD 8-10 including corrosion tapes and all accesories as required for complete installation as instructed by engineer in charge.

Supply and laying hot dip Galvanised Steel Flat having 70 microns zinc 30X3 mm thick from earth electrode directly in ground as required. Hot Dip GI strip, corrosion resistant. Cross sectional area of 90mm square According to DIN EN 50164-2 (VDE 0185 part 202) Meets the requirement of VDE0185/305(IEC 62305) Zinc coating: 500 g/m square (70 micron coating) Should be tested and use exclusively for lightning protection earthing system and ring equipotential bonding including cross connectors and all accesories as required for complete installation as instructed by engineer in charge.

Providing and fixing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate.

Supply and fixing of PVC trapezoidal 2.5m long ducts including the fastening clamps and all accessories as required.

Supply, installation and testing of maintenance free Earthing system as per IS 2309 ,IEC 62305 part3, IEC 60364, IEC 62561 part 2, IS 3043, UL 467 & UL 96 standards. Earthing System comprises of molecularly bonded copper of 99.9% purity on low carbon steel of 3m length (1m (219 20 CU) x 3 nos), having a diameter of 20mm with copper coating thickness of 250 microns with self-coupling bore and peg arrangement (without the need for external coupler) with fault current withstand capability of 20 KA rms value for 1 second and I peak of 50 KA. For obtaining desired length, the number of rods shall be increased and is provided with Universal Clamp (2730 20 VA) made of SS 304 for clamping the cable/flat conductor to the rod. Impact point (219 20 IP) on the bottom rod for easy insertion. Earth enhancing mineral compound (ECS PB 12.5) is used for improving the soil conductivity. Earth enhancing mineral compound shall be so designed and constructed that in normal use their performance is reliable and without danger to persons and the surroundings. The material shall be mineral inert to sub soil and shall not pollute the environment. It shall provide a stable environment in terms of physical and chemical properties and exhibit low resistivity. It shall not be corrosive to the earth electrode itself. The material should have a resistivity less than 0.2 Ohm meter. It should be free from hazardous substances The mineral compound is required to have minimum 12.5 Kg of the total composite. Polypropylene & Polyethylene (UFE)Earth electrode inspection chamber with heavy duty cover should be used to cover the Earth Rod. The dimension shall be 170mmx 170mmx 190mm with a weight bearing capacity of 5KN, including all accesories as required for complete installation as instructed by engineer in charge. (Minimum 2 earth pits shall be provided. No of earth pits shall be increased till overall earth resistance of the system is less than 10ohms as per site conditions and soil resistivity)

EARTHING Supply, installation and tesing of 1200mmx1200mmx12mm CI plate electrode earth station conforming to IS:3043-1987 / NEC / IEE complete with brick masonry chamber, CI cover, CI frame, GI watering pipe of 50 mm dia with funnel having 20G GI wire mesh etc. The CI cover frame/ chamber shall be of 450mm x 450mm size. CI manhole cover with frame shall be painted with bitumastic paint, identification of earthpit with yellow paint below the chamber cover, mixtures of charcoal & common salt around electrode including digging of pit up to permanent moisture level but not less than 3 metre depth and back filling. ( value of earth resistance should be less than 1 ohm )

Supply and laying the following sizes of Cu strips laid 0.6 m below ground level including excavating trench of suitable size and refilling ,including necessary clamps and bolts etc and all accessories as required for complete installation as instructed by engineer in charge/consultant. 25x3mm Cu strips tinned at the point of contact

Supply and laying the following sizes of strips on cable tray/wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant.

25x3mm Cu strips tinned at the point of contact

Copper wire No.10 SWG

Copper wire No.8 SWG

Providing coil/spring earthing using 8SWG, GI wire for street light pole etc. GI wire buried to a minimum depth of 1.5m, with excavation, refilling and connecting GI wire to pole using bolt and nut complete.

SAFETY EQUIPMENTS Supply and fixing of 4 Kg ABC Dry Powder (Stored Pressure) Type Fire Extinguisher. pressurized with dry nitrogen gas at 15 bar. Design, construction and testing as per IS 2171-1999 external epoxy powder coating with PO Red Shade No. 538 of IS 5, Supplied with standard accessories.

Supply & fixing of Class A Electrical rubber mat, used for up to 3.3 kV, Dielectric Strength of 33 kV , 2 Mtr x 1 Mtr size 2 mm thick, as per IS. 15652 - 2006 in front of various type MV panels. as per IS:15652 - 2006 with ISI certification mark of standard 1 Mtr width.The work includes cleaning of the floor, fixing of insulation mat by using suitable adhesive, waterproofing compound, sealing materials etc., complete as required

Supply and providing First Aid Box.

Supply and providing laminated First Aid chart duly framed and placed in a conspicuous location for clear vision.

Supply & fixing Laminated drawings of electrical lay out, schematic drawing etc on good frame work.

Supply and providing MS chequered plate of suitable thickness including cutting, welding, painting etc. as required for cable duct covering etc.

Supplying and installing at approved location approved make fire buckets of 24 gauge galvanized steel sheet, standard 9 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters “FIRE” in black and gold. Cost shall be inclusive of providing MS stand for 2 nos of fire buckes, or , duly painted over a coat of primer.

Supply of 1 pair 11 KV rubber hand gloves of approved make.

Supply & fixing of Class A Electrical rubber mat, used for high voltage 11kV , 2 Mtr x 1 Mtr size 3 mm thick, as per IS. 15652 - 2006. with ISI certification mark of standard 1 Mtr width.The work includes cleaning of the floor, fixing of insulation mat by using suitable adhesive, waterproofing compound, sealing materials etc., complete as required

LIASIONING WORKS Preparation of all documents & submitting and getting initial and final approvals from Electrical Inspectorate, submitting of Completion certificates and arranging inspection, getting sanctions and energisation certificates, test reports. Preperation of shop drawings for execution at site and getting them approved by engineer in charge/consultant before execution at site, preperation of As-built drawings of installation upon completion. Obtaining manuals, technical details,as-built/GA drawings of all equipments from concerned and arranging technical class for maintenance staff of the complete installation for timely maintenance and working and also obtaining all necessary sanctions from relevant regulatory boards, submitting of test certificates of all equipments obtaining power allocation & power connection etc. for commissioning of the whole installation in the premises. All statutory payments will be reimbursed on production of the original receipts.

EXTERNAL YARD WORKS LT CABLE SUPPLY Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date.

2x10sq.mm Al Cable

2x6sq.mm Al Cable

LT CABLE TERMINATION Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

2c X 10 sq. mm (DSR 9.1.2)

2cx6 sq mm (DSR 9.1.2)

EXTERIOR LIGHT FIXTURES Supply, fixing, testing and commissioning of 10 M octagonal poles of approved make having top dia 70 mm, bottom dia 175 mm, Sheet thickness 3 mm, pitch circle dia (PCD) of 275 mm, Base plate diamentions 275 mm length x 275 mm bredth x 16 mm thickness, EN8 grade Foundation bolts of size 4 x 24 mm dia, having bolt length of 750 mm. The Octagonal Poles shall be designed to withstand the maximum wind speed as per IS 875. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The octagonal Poles shall have door of approximate 500 mm length at the elevation of 500 mm from the Base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connections. The door shall be flush with the exterior surface and shall have suitable locking arrangement. There shall also be suitable arrangement for the purpose of earthing. Material Octagonal Poles HT Steel Conforming to grade S355JO. Base Plate Fe 410 conforming to IS 226 / IS 2062, Foundation Bolts EN.8 grade The poles shall be hot dip galvanised as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 85 micron. The galvanizing shall be done in single dipping. The pole shall be with one arm for fixing one number 120 W LED fixture with pressure die-cast aluminium alloy housing with corrosin resistance powder coating using nano technology, UV stabilised injection moulded PC cover for optimum light transmission, IP 66 protection including all accesores as required. Make: ( Lighting technology Adornis INT 120W 5700K LED pole mount street light or equivalnet)

Supply, fixing, testing and commissioning of 8 M octagonal poles of approved make having top dia 70 mm, bottom dia 175 mm, Sheet thickness 3 mm, pitch circle dia (PCD) of 275 mm, Base plate diamentions 275 mm length x 275 mm bredth x 16 mm thickness, EN8 grade Foundation bolts of size 4 x 24 mm dia, having bolt length of 750 mm. The Octagonal Poles shall be designed to withstand the maximum wind speed as per IS 875. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The octagonal Poles shall have door of approximate 500 mm length at the elevation of 500 mm from the Base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connections. The door shall be flush with the exterior surface and shall have suitable locking arrangement. There shall also be suitable arrangement for the purpose of earthing. Material Octagonal Poles HT Steel Conforming to grade S355JO. Base Plate Fe 410 conforming to IS 226 / IS 2062, Foundation Bolts EN.8 grade. The poles shall be hot dip galvanised as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 85 micron. The galvanizing shall be done in single dipping. The pole shall be with one arm for fixing one number 90 W LED fixture with pressure die-cast aluminium alloy housing with corrosin resistance powder coating using nano technology, UV stabilised injection moulded PC cover for optimum light transmission, IP 66 protection including all accesores as required. Make: ( Lighting technology Adornis INT 90W 5700K LED pole mount street light or equivalnet)

Supply, fixing, testing and commissioning of 8 M octagonal poles of approved make having top dia 70 mm, bottom dia 175 mm, Sheet thickness 3 mm, pitch circle dia (PCD) of 275 mm, Base plate diamentions 275 mm length x 275 mm bredth x 16 mm thickness, EN8 grade Foundation bolts of size 4 x 24 mm dia, having bolt length of 750 mm. The Octagonal Poles shall be designed to withstand the maximum wind speed as per IS 875. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The octagonal Poles shall have door of approximate 500 mm length at the elevation of 500 mm from the Base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connections. The door shall be flush with the exterior surface and shall have suitable locking arrangement. There shall also be suitable arrangement for the purpose of earthing. Material Octagonal Poles HT Steel Conforming to grade S355JO. Base Plate Fe 410 conforming to IS 226 / IS 2062, Foundation Bolts EN.8 grade. The poles shall be hot dip galvanised as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 85 micron. The galvanizing shall be done in single dipping. The pole shall be with two arms for fixing one number 90 W LED fixture with pressure die-cast aluminium alloy housing with corrosin resistance powder coating using nano technology, UV stabilised injection moulded PC cover for optimum light transmission, IP 66 protection including all accesores as required. Make: ( Lighting technology Adornis INT 90W 5700K LED pole mount street light or equivalnet)

Supply, installation, testing and commisioning of 25W Post top lantern with good light distribution ,with pressure die-cast aluminium alloy housing with corrosin resistance powder coating using nano technology, UV stabilised injection moulded PC cover for optimum light transmission, and integrated electronic drive with weather proof protection(IP 65) and all necessary accessories (Lighting technology Adornis Min 25W LED psot top or equivalnet). The item shall also include pole for mounting the fixture (Make : Lighting Technology or equivalent)

MV & HT CABLE LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mm(dsr 7.1.1)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the exisitng RCC/Hume/Metal pipe as required. Upto 35 sq. mm(dsr 7.5.1)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct as required. Upto 35 sq. mm(dsr 7.6.1)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)(dsr 7.7.1)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)(dsr 7.8.1)

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required. 40 mm dia (DSR 11.6.2)

TERMINATION BOXES Supply, installation, testing and commisioning of self extinguishing, weatherproof cabinets suitaible tfor outdoor application (IP 65, IK 09) with reversible door and cabinet with terminals for looping of cables and rail for fixing modular isolator along with 25A DP isolator including all connections and interconnections as required for outdoor application as instructed by engineer in charge.

PART A: SANITARY FIXTURES AND CP FITTINGS: Supply, Installation, Testing, Commissioning of Vitreous China wall mounted two piece European water closet - snow white with seat and cover (with 'P' trap of IS specification make and approved by the consultant) , MS / CI chair brackets, fischer bolts with CP bolts / nuts and with with CP flanges, solid plastic seat and lid with heavy duty CP hinges and rubber buffers and flap etc. The work shall include cutting making of walls and floors etc. Notes: Necessary consumables like brass screws, CP extension nipple of approved make, dia and length, wooden plugs, white cement, sealants etc., required if any, shall be arranged by the contractor. Only drilling machines shall be used for making the holes in the walls for fixing, no wall jumper and hammer will be allowed.(EWC+Cistern) Make:cera calibre/ equivalent

Supply, instalation,testing and commissioning of Vitreous China wall mounted European water closet - with seat and cover (with 'P' trap of IS specification make and approved by the consultant) , MS / CI chair brackets, fischer bolts with CP bolts / nuts and with concealed cistern with CP flanges, solid plastic seat and lid with heavy duty CP hinges and rubber buffers and flap etc. The work shall include cutting making of walls and floors etc. Notes: Necessary consumables like brass screws, CP extension nipple of approved make, dia and length, wooden plugs, white cement, sealants etc., required if any, shall be arranged by the contractor. Only drilling machines shall be used for making the holes in the walls for fixing, no wall jumper and hammer will be allowed.Make:Cera Carat/ Jaquar- Vignette,Continental /equivalent

Make: Cera Carat

Make: Jaquar-continental / equivalent

Make: Jaquar vignette / equivalent

17.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests MAKE: Cera -CALINA orissa pan/ Equivalent (Flush tank-Cera -combiflush)

17.18 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 17.18.1 10 litre capacity - White

Supply, Installation, Testing, Commissioning of colour vitreous china counter top wash basin- installed on granite/ marble with CI / MS brackets, 32mm dia CP waste coupling with plug and chain, PVC / CP cold watersupply connecting pipe, one no of 15mm dia CP angle stop cock for cold watersupply liness with wall flange etc as per IS specification make and approved by the consultant. The works shall include cutting in walls and making good the walls & floors. .(Granite / Marble counter will be installed by other agency)

Make: Cera CLIFF / equivalent

Make: Cera CAMARA / equivalent

Make: Jaquar JDR / equivalent

Supply, Installation, Testing, Commissioning of wash basin White or equivalent, fitting waste coupling , Rag bolt, PVC connection , waste pipe to PVC pipe necessary washers, white cement, all other accessories etc. complete in all respects . complete up to PVC pipe connection.including necessary solvent cement, socket, if any other fittings which are not included in fitting items etc.complete as required. (Wash basin+Piller cock) Make: CERA- Canon-450 x350 size

Supply, instalation,testing and commissioning of shower with divertor and spout with inlet body, conversion bend for overhead shower with wall flanges and shower arm, valve plate lever, etc as per IS specification make and approved by the consultant, complete in every respect including, cutting, chasing & making good the walls .MAKE: Jaquar-Allied (ALD-065 (Divertor) FLR-5065K (Exposed part) SPJ-429 (Spout) ,SHA-477 + OHS- 1995 ( shower arm and shower)

Supply, instalation,testing and commissioning of approved make CP shower unit with concealed part for concealed stop cock suitable for 20mm pipeline with inner head with out exposed parts with 220mm long bend pipe for over head shower with CP wall flanges. make: Jaquar-SHA-477 +OHS 1995

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.2 Kitchen sink without drain board 17.10.2.1 610x510 mm bowl depth 200 mm

supply and labour

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.2.3 470x420 mm bowl depth 178 mm

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.1 Semi rigid pipe 17.28.1.1 32 mm dia

17.69 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Fixing of stainless steel sink with Single bowl and single drain board of approved size manufactured from 1 mm thick stainless steel, 18/8 grade SS-304 indestructible chrome nickel steel with top quality polish, 40 mm dia CP waste coupling with extension flexible pipe of suitable dia etc gloss finish., complete. fixing of granite counter shall be done by the external agency.Make : cera-diana lite-940 x455mm size/equivalent

Fixing of urinal pan snow white urinal flat back normal (340x280x470mm).including necessary solvent cement, socket, if any other fittings which or not included in fitting items etc.complete. Make cera CHRYS / equivalent

Fixing of urinal pan snow white urinal flat back normal (375x390x590mm).including necessary solvent cement, socket, if any other fittings which or not included in fitting items etc.complete. Make cera CAPRIANA / equivalent

Fixing of approved make & Snow white coloured urinal division plate of size 90 x320x720mm and fixed to wall by using CP brass screws etc. complete as per specifications. Make cera -CORVIN /equivalent

supply and labour

Fixing of 15mm CP angle cock with flange complete as per IS specification make and approved by the client / consultant, including cutting and making good the wall etc. complete MAKE:JAQUAR-Continental-059KN

Fixing of CP health faucet as per IS specification make ABS body with 1meter long easy flex tube in chrome finish and wall hook and approved by the client /consultant consisting. Make JAQUAR- Allied/equivalent

17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Fixing of approved make SS grab bar with CP flanges, fixed with SS screws complete . Location : Handicap Toilet. MAKE Cera-cat no-b2210106 /equivalent

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 17.32.2 Rectangular shape 453x357 mm

Fixing of Paper towel dispenser as per IS specification make and approved by the client / consultant, including cutting and setting in walls with cement joints and making good the wall. Make - JAQUAR-PTD-SAP DT0106CS/ equivalent

Fixing of tumbler holder as per IS specification make and approved by the client / consultant, including cutting and setting in walls with cement joints and making good the wall. Make -JAQUAR- ACN1141N / equivalent

Fixing of soap dish holder as per IS specification make and approved by the client / consultant, including cutting and setting in walls with cement joints and making good the wall. Make -JAQUAR- CAN-1131N / equivalent

Fixing of superior quality Rob hook with brackets and flange with concealed brass screws etc as per IS specification make and approved by the client / consultant, including cutting & making good the walls. Make JAQUAR-CAN-1161 N/ equivalent

Providing and fixing C.P. brass sink cock (table mounted) with 170mm long swivel spout including cutting and making good the walls wherever required of approved quality. Make :Jaquar/ Cera F2004301

Fixing at site in position 15mm dia C.P Piller cock with neck spout and aerator including cutting and making good the walls wherever required. Make JAQUAR-Pressmatic

Supply, instalation,testing and commissioning of approved make of vertical / horizontal type Electric water heater suitable for pressure rating up to 4 Kg / Sqcm with heating element with thermostat, pressure relief valve, non - return valve with CP copper connecting pipes with wall flanges etc., complete with all inlets, outlets, valves and all other accessories etc., complete. Toilet Geyser.6KG make: Jaquar -Elena

Fixing of toilet paper holder : C.P. brass as per IS specification make and approved by the consultant including cutting and setting in wall with cement joints and making good the wall. MAKE JAQUAR- ACN-1151N

Supply, instalation,testing and commissioning of Jacuzzi with all CP fittings 15mm dia CP pillar cock fitting, 32mm dia CP waste coupling with plug and chain,32mm dia CP brass trap, PVC / CP hot & cold watersupply connecting pipe, two/more nos of 15mm dia CP angle stop cock for hot & cold watersupply liness with wall flange etc as per IS specification make and approved by the consultant. The works shall include cutting in walls and making good the walls & floors. make Cera-CAROL

PART B : WATER SUPPLY (INTERNAL AND EXTERNAL ):CPVC PIPES AND FITTNGS 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal outer dia Pipes

18.8.2 20 mm nominal outer dia Pipes

18.8.3 25 mm nominal outer dia Pipes

18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brassthreaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

18.9.2 20 mm nominal outer dia Pipes

18.9.3 25 mm nominal outer dia Pipes

18.9.4 32 mm nominal outer dia Pipes

18.9.5 40 mm nominal outer dia Pipes

18.9.6 50 mm nominal outer dia Pipes

Supply and fixing of UPVC pipes and fittings / specials like tees, elbows, bends, unions, offsets, Hex nipples collars, cutting, threading the pipes with threading machine, jointing using holdtile and cotton thread or shallock and pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc., including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CC or CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors.Make:Supreme / Finolex DWS SHAFT / CEILING /TERRACE PIPING:

20 mm dia sch 40

25 mm dia sch 40

32 mm dia sch 40

40 mm dia sch 40

50 mm dia sch 40

65 mm dia sch 40

18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall

18.10.4 32 mm dia nominal bore

18.10.5 40 mm dia nominal bore

18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

18.18.2 20 mm nominal bore

18.18.3 25 mm nominal bore

Supply and fixing of ball valves of brass body nickel plated with stainless steel ball, lever operated ( as per IS specification make and approved by the client / consultant) and tested to 20kg / sq.cm.MAKE : Zoloto /sks

32 mm dia

40 mm dia

50 mm dia

Supply and fixing cast iron lever operated slim seal type butterfly valves of CI body and spheroidal graphite iron disc (SG iron),with nitrile rubber seal, tested to 10 kg / sq.cm Confrming to BS 5155 / MF6 standards and including a set of GI flanges as per BS 10 table 1 including bolt nuts, and Neoprene rubber gaskets etc.,complete as required.MAKE : Zoloto /sks

65 mm dia

50 mm dia

18.19 Providing and fixing gun metal non- return valve of approved quality (screwed end) :

18.19.3 40 mm nominal bore

Supply & Fixing of brass body nickel plated automatic air release valves with necessary GI Specials, thread, holdtight, brass spindle, NBR and elastomeric, stainless steel spring polypropylenic float at the top most points of water supply distribution ring main. 20 mm dia.

20 mm dia

Supply & Fixing at site in position Fabricated u PVC Astm Sch 40 Puddle flanges in the underground and overhead water tanks as per the drawings and the requirement of the Project Manager.

50mm dia

65mm dia

80mm dia

100mm dia

Construction of valve chambers with `75' class designation bricks with cement motar joints including excavation,plastering & providing cast iron man hole cover as required.

Size 450 x 450 x 450mm deep

Supply and Fixing of Universal clamp With Threding Rod Completed Make: Hitech

15mm To 32mm (supply and labour)

40mm To 65mm (supply and labour)

75mm To 110mm (supply and labour)

PART – C: PVC SOIL,WASTE,VENT PIPES AND FITTINGS ( INTERNAL & EXTERNAL) Supply and laying of PVC soil, waste and vent pipe confirming to IS 13592 of SWR quality 6 kg / sq.cm pressure rated including all fittings, like Bends, Tees, Elbows, Collars, junction, offsets, access pipes, jointing with solvent cement followed by application of leak proof adhesive like FRP paste & laid on floors inside the toilets kitchen and utility to the required slope including making necessary bores in walls / foundations / concrete slab as applicable, making good the bores with CM 1:3 or cement concrete 1:2:4 as applicable, curing etc., complete. INTERNAL:

50mm dia (6kg / sq.cm)

75mm dia (6kg / sq.cm)

110mm dia (6kg / sq.cm)

75mm dia (4kg / sq.cm) vent pipe

Supplying, fixing ,testing and comissioning SWR PVC pipes selffit type confirming to IS 13592 including all fitting, like bends, tees, Elbows, Collars, Junctions, Inspection doors, Cowls, offsets access pipes jointing with rubber ring /solvent cement followed vy application of leak proof adhesive fixed on wall with properly fabricated MS bracket of suitable size ,GI U Clamp with bolts ,nuts and GI washers ,complete for soil and waste water pipelines laid in shafts

75mm dia (6kg / sq.cm)

110mm dia (6kg / sq.cm pr. Rated)

75mm dia (4kg / sq.cm) vent pipe

Supply and laying of PVC soil and waste pipes for underground drainage line layed under the soil with required slope, confirming to IS 4985 of Agricultural series - 6 kgs / sq.cm pressure rated with necessary specials of required size jointing with solvent followed by application leak proof adhesivesof FRP paste, including haunching / covering the joints with cement concrete 1:3:6 at all the joints and testing of joints etc. complete. pipe lines from manhole to STP.

75 mm dia 6kg / sq.cm

110 mm dia 6kg / sq.cm

160 mm dia 6kg / sq.cm

Supply and fixing of PVC multi inlet floor trap of self cleansing design moulded or fabricated, if not available in size mentioned below, with or without vent arm jointing with solvent cement followed by application of leak proof adhesive like FRP paste including encasing all round fixing the floor trap in cement concrete 1:2:4 ratio of size 300 x 300 mm x 250 mm height (approx) and making good the floors.

110mm dia

Supply and fixing of CP grating of 6mm thick with rim including setting in floor with white cement mortar and making good the floor.

110mm dia

19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 19.4.1 100x100 mm size P type 19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size of 300 x 300 mm & depth not exceeding 900mm . :

Construction of brick masonry inspection chambers of internal clear dimension as mentioned below by using country bricks 230 mm thick wall in cement mortor joints in 1:4, over CC 1:4:8 bed 150 mm thick, inside plastering15mm thick with CM 1:3 (1 cement::3 fine sand) finished very smooth with floating coat of neat cement & making benching and channelling in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate) neatly finished complete as per standard design and as per drawing and specifications. (The rate shall include necessary earth work excavation in all types of soil excluding soft and hard rock, back filling including consolidation disposing the excess earth to all leads curing, finishing etc., complete).including cast iron man hole cover medium duty (62kg) (The rate shall include earth work excavation and back filling)

Inside size of 600 x 600 mm & depth not exceeding 900mm. :

Supplying, Installing & Testing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects.

160 mm dia

110 mm dia

75 mm dia

PART – D: PVC RAIN WATER PIPES AND FITTINGS Supplying and laying of PVC rain water pipe confirming to IS 13592 of SWR quality 4 kg / sq.cm pressure rated, including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, offsets, access pipes, jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI 'U' clamps with bolts, nuts and GI washers complete, for rain water pipe lines laid in vertical shafts.

75mm dia ( 4kg / sq.cm)

110mm dia ( 4kg / sq.cm)

Supplying and laying of PVC Rain water pipes for underground drainage line layed under the soil with required slope, confirming to IS 4985 of Agricultural series - 6 kgs / sq.cm pressure rated with necessary specials of required size jointing with solvent followed by application leak proof adhesivesof FRP paste, including haunching / covering the joints with cement concrete 1:3:6 at all the joints and testing of joints etc. complete as required.

110mm dia ( 6kg / sq.cm)

160mm dia ( 6kg / sq.cm)

Constructing Rain water manhole of size 450mm x450mm inside and depth not exceeding 120 cm with 20 cm( country brick) thick walls in cement mortar 1:6 plastering inside with cement mortar 1:3, 12 mm thick with neat flushing coat and foundation concrete 20 cm thick and forming chanels with cement concrete 1:3:6 using 40 mm broken stones, providing collars around pipes with cement concrete 1:2:4 using 20 mm broken stones , corbels at top courses on two sides with cement concrete 1:1.5:3 using 20 mm broken stones and necessary reinforcement and providing necessary CI /PVCstep including cast iron man hole cover medium duty (62kg)

RCC beams 250 mm thick- 50mm dia

RCC beams 250 mm thick- 75mm dia

RCC beams 250 mm thick- 110mm dia

RCC slabs (For Wash Basin, EWC & Floor Trap) 150 mm thick- 110mm dia

RCC slabs (For Wash Basin, EWC & Floor Trap) 150 mm thick- 75mm dia

RCC slabs (For Wash Basin, EWC & Floor Trap) 150 mm thick- 63mm dia

RCC slabs (For Wash Basin, EWC & Floor Trap) 150 mm thick- 50mm dia

Fixing of Automatic Three phase water level controllers with level sensors for submersible pump shall have the following features 1.Switch off the motor when the water level in tank reaches a preset level below the over flow pipe.2.Switch ON the motor if the water level in tank goes down below a preset value near.3.Switch off the motor in the event of dry running.4.Manual bypass mode.water level controller is suppled by client in free of cost.

Laying of 4 pair 0.5 sq mm cable as control cable of liquid water level controller through a ISI Heavy duty 20mm conduit. Cable supplied by client free of cost.

All works to be carried out to relevant IS specifications whether so mentioned in description of works or not. Only Electrically operated instruments including hammer drilling, Core cutting, groove cutting and other equipments shall be used. The schedule of probable quantities may vary on the higher side or lower side. Hence, during material pocurement, the contractor shall workout the actual quantites based on the good for construction/shop drawings issued for execution as per the project manager's direction. All extra and surpuls material if any will be on contractor's risk and must be carried away from the site upon completion and hand over of the works.The contractor should intimate the consultant & client regarding the progress of work and should submit weekly reports.

FIRE PUMP AND HYDRANT SYSTEM Supply, erection, Testing and Commissioning Terrace Pump rated for 450 LPM @ 35 Mtr head high efficiency volute type with caste iron casting , impeller, pump coupled to squirrel cage induction motor,totally enclosed fan cooled with supply condition 415 V,3 Phase, 50 HZ foot mounted type rated for required HP at 2900 rpm.including Eletrical Motor Starter for the Booster Pump star delta type with necessary starter contactors and push button stwiches. Suitable RCC Pump-Foundations as per manufacturer's design

Providing and fixing Single headed, S.S. ISI marked oblique pattern hydrant landing valve with 80 mm dia flanged inlet and 63 mm dia instantaneous type female outlet complete with gunmetal cap and G.I. chain, twist release type plug and all accessories as per IS:5290. Make of materials : Newage,Minimax,AAG Supply & Erection

Providing and fixing Non-percolating flexible hose (RRL type-'A') ISI marked (IS:636) 63 mm dia x 15 M long complete with instantaneous type S.S. 63 mm dia. IS marked Male and female couplings (IS:903) bound and riveted to hose pipe with copper rivets and 1.5 mm copper wire.(For internall Hydrant valves) Make of materials : Newage,Minimax,AAG Supply & Erection

Providing and fixing S.S. 63mm dia short size branch pipes with 20 mm dia nozzles with 63mm instantaneous coupling ISI marked (IS: 903). Make of materials : Newage,Minimax,AAG Supply & Erection

Providing and fixing first aid fire hose reel (with wall mounting swinging-type drum complying to IS:884), fitted with Thermo Plastic Synthetic Reinforced material conforming to IS:12585 Type II 20 mm bore, with 5mm outlet S.S. nozzle and shut off valve, brackets, complete. Supply & Erection Make of materials : Newage,Minimax,AAG

Supply and Fixing of weather proof Hose cabinet suitable size " 30 x24 x10 inch having made of 16 gauge MS Sheet with common keylock arrangements, suitable to accommodate two lengths of 15mtr hoses,one headed hydrant valves , hose reel and one no branch pipe with nozzle. The cabinet shall be painted to scarlet red colour out side and off-white inside. for internal and external Make of materials : Newage,Minimax,AAG Supply & Erection

Providing and fixing Gun-metal 3-way fire brigade inlet connection of 3nos. 63mm dia instantaneous type male coupling with built in check valves and 100mm dia flanged outlet complete with bolts, nuts and rubber insertions as per I.S:904. (to be connected to riser). Make of materials : Newage,Minimax,AAG Supply & Erection

Providing and fixing wafer type,S.G iron, without lugs,lever operated Butterfly valves (PN10) complete with all accessories. MAKE: KARTAR/ ZOLOTO 100 mm dia Supply & Erection

Supplying, installing, testing and commissioning of CI body, chromium plated Ball valves with fittings of screwed end type.MAKE: KARTAR/ ZOLOTO 25 mm dia

Supply,Installation,Testing and Commissioning of Air Release Valve GM 20mm dia type of approved make.ATOM

Providing and fixing Swing type with Natural rubber flap non-return valves (PN 10) complete with matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes. MAKE: KARTAR/ ZOLOTO 100 mm dia

Supply,Installation,Testing and Commissioning of Pressure switch bellow type of approved make. Make: Dunfoss / Indfoss

Supply, Installation,Testing and Commissioning of Pressure gauge with 0 to 200PSI, 25 mm dia. Make: Dunfoss / H-guru / Oasis

SUPPLY, INSTALLATION, TESTING & COMMISSIONING of GI heavy duty grade 'C' class pipe (IS:1239 Part-I) including cutting, threading, welding etc. bends, elbows reducers, clamps, hangers etc. including cutting holes in brick or RCC walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including all steel work. MAKE: TATA/JINDAL

25mm dia

80 mm dia

100 mm dia

100 mm dia (External)

Extingushers Supply and fixing ABC Powder based Fire Extinguisher of capacity 4.5 kg filled with Mono Ammonium Phosphate with nitrogen as per IS 15683with control dis mechanism. Make Of Materials : MINIMAX /CEASEFIRE

Supply and fixing o ISI marked (IS:2878) Fire Extinguisher, Carbon-di-oxide type capacity 2 Kg. Flat base including valve, discharge hose of not less than 10 mm dia, 1M long and complete in all respects including initial fill with CO2 gas conforming to IS:307-1966 filled to a filling rate of not more than 0.667 and wall suspension bracket. Make Of Materials : MINIMAX /CEASEFIRE

Supply and fixing K type Fire Extinguisher of capacity 2 kg filled as per ANSI / UL-711, UV resistant Vinyl Label

CONVENTIONAL FIRE ALARM SYSTEM Supply, Installation,testing and commissioning of 6-Zone Conventional Panel with thrirty minites battery backup with necessary indications, solid - state circuitary with visual front and alarm display.The panel shall be designed that the audio alarm activation and silencing switches.The C& I panel be provided with repeated system for both audio as well as visual.The panel should have facility to attach stand by power system using batteries with all necessary attachments as required and directed. Make Of Material :Hochiki/Siemens/MORLEY/AGNI

Supply, Installation,testing and commissioning of Manual Call Point,Flush Mounting, Flexi Elements with Break glass type withcast Aluminium housing, hammer and chain as perdetailed specification. Approved makes : Monsher/Seimens/MORLEY/AGNI

Supplying, installing, testing and commissioning approved make Red Mini Horn, Red, UL certified, Hooters with suitable mounting base etc.,complete as per detailed specification. Approved makes : Hochiki/Siemens/MORLEY/AGNI

Supply laying and termination of 2 Core x 1.5 Sq.mm cable, Armoured Screened FRLS Twin Twisted PVC Insulated copper cable along with all accessories. Approved Make : Polycab, Havells, Finolex

Supply and fixing of fire shaft doors of 2hrs fire rating with a minimum size of 1500mm hgt * 700mm width ,enclosed by wails and door as per the site condition. Approved makes : Fabricated

Supply and fixing of 1 x 6W, 240 V, 1 ph, 50 Hz indoor type emergency exit light fixture with 1.3 AH 4hrs battery back up unit, LED Lamps, indicating Fire Exit, recess mounted type. 24hrs x 7days working conditional.MAKE :

Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyle painted foam board, complete with mirror fasteners. Size : 60cm x 15cm MAKE : SECULITE

Preperation of the as built drawings of suitable size and sufficent number of copies to be submitted to local authorities and obtaining sanction from Fire and rescue department. Final NOC for the whole installation in the premises shall be obtained after testing and commissioning the proposed work. [ Obtaining sanctions is part of contract for releasing the final payments]. All statutory payments will be reimbursed on production of the original receipts.

CCTV SYSTEM Supply, Installation,testing and commissioning of 2.8 mm fixed lens, 2MP , IR Dome camera 1.0 lux, 120 db WDR POE and vandal proof with all connectors and necessary accessories for mounting in True/false ceiling

Supply, Installation,testing and commissioning of Varifocal Dome Camera with 2 MP 0lx, built-in IR LED,120DB WDR , 2.8-12 mm POE,Vandal proof with all connectors and necessary accessories for mounting on true/false ceiling

Supply, Installation,testing and commissioning of Indoor Varifocal Bullet Camera with 2 MP , built-in IR LED, , 2.8-10 mm POE , IP 66 with all connectors and necessary accessories for mounting in false ceiling/True Ceiling

Supply, Installation,testing and commissioning of Outdoor Varifocal Bullet Camera with 2 MP , built- in IR LED, , 2.8-10 mm POE , IP 67 with all connectors and necessary accessories for mounting in Pole/Exterior wall

Supply, installation, testing and commissioning of 32 Channel Network Video Recorder Supports 32 channels 720p resolution video recording at real time, NVR ONVIF , Recording resolution of Max 12 MP, Minimum of 200Mbps of recording, should support dual video output, H.265,H.264, MJPEG Compression.video playback / relay at real time.

Supply, installation, testing and commissioning of HDD for cameras recording at 720p @ 20fps for 30 days 24 hours - 6 TB

Supply, installation, testing and commissioning of workstation with Intel I7 or above, 8 GB ram and 2 TB HDD. Same system will be used for Access control

Supply, Installation, Testing and Commissioning of LED Monitor 40" with all required accessories

ACCESS CONTROL SYSTEM Supply, Installation, Testing and Commissioning of standalone type Proximity Card based access control system with LCD display, suitable for IP connectivity to integrate with access control software.

Supply, Installation, Testing and Commissioning of Biometric reader with inbuilt proximity reader for Time and attendance, in /out time recording, LCD display, suitable for IP connectivity to integrated with T & A management software

Supply, Installation, Testing and Commissioning of licensed security management software with Time Attendance and Access control including programming of access cards.

Supply, Installation, Testing and Commissioning of Proximity Cards

Supply, Installation, Testing and Commissioning of Exit push button

Supply, Installation, Testing and Commissioning of Single Leaf Electro Magentic Lock with Magnetic door sensor Contact with necessary brackets

Supply and Surface laying of 2 CoreX 1.0 Sq.mm unrmoured shielded FRLS PVC Insulated Cable - controller to controller

PASSIVE Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required

1 run of cable

24 Port Cat6 Patch Panel with all accaessories loaded

Supply, fixing, testing and commissioning of Cable Manager

Supply, fixing, testing and commissioning of CAT6 Patch Cable - 2 Meter as required for complete installation.

Supply, fixing, testing and commissioning of CAT6 Patch Cable - 1 Meter as required for complete installation.

Supply, fixing, testing and commissioning of CAT6 Information Outlets for Data with faceplate, Keystone Jack, Back box etc. as required for complete installation.

Supply, fixing, testing and commissioning of Keystone jack for data outlets (for Camera and Wifi access points) as required installation.

19", 9U 500 MM wide x 550 MM Depth Wall Mount Networking Rack with Front Glass Door, Horizontal Cable M anager - 2 Nos, Cantilever Shelf - 1 No, Horizontal PDU 6X5Amps - 1 No, Cooling Fan - 2 Nos, Hardware Screws and all other required accessories

19", 15U 600 M M Wide X 800 M M Depth Floor/Wall Mount Networking Rack with Front Perforated Convex Door, Rear Perforated SPLIT Doors, Side Openable Panels, Castors, Heavy Duty Shelf - 1 No, Horizontal Cable M anager - 2 Nos, Cantilever Shelf - 1 No, Vertical PDU 12X5Amps - 1 No, Fan Housing Unit with 4 Fans - 1 Set, M ounting Hardware Screwsand all other required accessories

19", 42U 800 MM Wide X 1000 MM Depth Floor Mount Server Rack with Front Perforated Convex Door, Rear Perforated SPLIT Doors, Side Openable Panels, Castors, Heavy Duty Shelf - 1 No, Horizontal Cable M anager - 2 Nos, Cantilever Shelf - 1 No, Vertical PDU 12X5Amps - 1 No, Fan Housing Unit with 4 Fans - 1 Set, M ounting Hardware Screwsand all other required accessories

SWITCHES Supply, Installation, Testing & Commissioning of 24 port 10/100/1000 Base-T Network switch with 24 port PoE 1G copper uplink and all related termination accessories as per vendor specific System requirement. 24 Port PoE Switch

Supply, Installation, Testing & Commissioning of 24 port 10/100/1000 Base-T network Switch with 1G copper uplink 24x 1G ports and all related termination accessories as per vendor specific System requirement. 24 Port Switch

Supply, Installation, Testing & Commissioning of 24 port 10/100/1000 Base-T Manegable L3 Core Switch with 10G fibre uplink 24x 1G copper ports and all related termination accessories as per vendor specific System requirement. 24 Port Switch

WIFI Supply, Installation, Testing and Commissioning of Wifi Access Point with Dual Band 8011.ABGN/AC 1200 Mbps Speed

Supply, Installation, Testing and Commissioning of Wifi Controller with licence for minimum 30 Wifi Access points to manage the bandwidth, privilege, password etc

EPBAX Supply, Installation, Testing and Commissioning of "PBX with 30 Analog extensions expandable up to 50 ports (Extensions/Trunks) , 5 Digital Extensions and with maximum of 10 concurrent calls Network Interface: 1×10/100M LAN port 4 Analog Trunks expandable upto 8, Power Consumption: 12V/0.8A, 9.6W Maximum, Failover Function (optional), Web Interface, Call Dashboard, DISA, IVR, Call Hunt, etc. Features:Room monitoring from outside Warning Message during night mode Remote Inspection, with auto-emergency call Sensor Connectivity with auto-emergency call and warning message sending Built-In Auto Answer (Standby mode) during night mode Voice Mail Integration Paging Announcement Programmable Function Keys" Programmable Function Keys"

Supply, installation, testing and commissioning of single line digital phone with 5 navigation keys with necessary connection as required for complete installation.

Supply, installation, testing and commissioning of Basic user phone with necessary connection as required for complete installation as directed by the engineer in charge.

Supply and fixing 50 pair 0.51 mm dia telephone tag block "Krone or equivalent make" with termination box

Supply and fixing 10 pair 0.51 mm dia telephone tag block "Krone or equivalent make" with termination box

Supply and laying 10 pair telephone cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supply and installation of modular type telephone socket outlet mounted in seperate PVC box including supply of modular PVC mounting box, telephone socket covering with modular coverplate giving connection etc as required.

PROJECTOR Supply, Installation, Testing & Commissioning of 3300 Lumen Short through Projector WXGA with HDMI, VGA out,USB connectivity

Supply, Installation, Testing & Commissioning of 120-135" diagonal, Wall mountable, Projection screen

Supply, Installation, Testing & Commissioning of Audio System for projector with 2x15 Watts speaker, amplifier for connecting multiple sources for Mic, projector audio inputs etc with all the cables & suitable accessories required

Supply, Installation of HDMI cable - 15 metr

Supply, Installation of VGA cable - 15 Meter

PA system Supply & Installation of Wall mount 12 W Speaker for PA system

Supply & Installation of ceiling mount 6W Speaker for PA system

Supplying, installing, testing and commissioning Audio booster Amplifier 240 Watts RMS, complete with Speaker wires and RGB connectors for Integrated Music & PA system

Supplying, installing, testing and commissioning of Digtal PA Master Processor with fully Digital Audio system for Public Address and Evacuation consisting of audio digital signal processing (DSP), a matrix, digital message player, 40min Audio message memory, Fireman microphone on Front side for Emergency paging, Red color EVAC button on Front, amplifiers monitoring with switchover to backup amplifier, loudspeaker lines monitoring(mandatory), LCD display for fault checking, Onboard volume control for each zone, Integrate with PBAX System for announcement.. Note: Master processor should incorporate minimum of 6 zones.

Supply & Installation of 6 zone call station with mic

Supply, installation, testing & commissioning of Audio player with DVD/USB /FM/ WiFi connectivity option for playing music

Supply & Wiring of Speaker system using 2core of 1.5sqmm PVC insulated copper FRLS unmoured cable

INTEGRATED LIBRARY MANAGEMENT SYSTEM Supplying, installing, testing and commissioning of Integrated Library management system with RFID Integrater Reader with tag writer, RFID gate Reader, Portable RFID reader, Library management software with middleware integration and all required connetors and accessories to complete the installation. Book data entry for all available books shall be done at the time of installation.

Supplying and fixing RFID Tag for books

Supplying and providing RFID CARD with Printing for library patrons

MISCELLANEOUS Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

Supply and fixing of Perforated Cable tray with horizontal & vertical bends, reducers, Tee's, cross over , suitable supports and brackets and other accessories as required confirming to IEC-61537. The Tray shall be galvanized for corrosion protection confirming to DIN EN 10346 / ISO 1461 .The trays should be tested for a max. safe working load of 150 Kgs with a span distance of 1.5 meters and the deflection should be within the limits as per standard. The safety factor shall be 1.7 times of the safe working load. The perforated tray shall be supplied with the standard length of 3 Mtr . (OBO Betterman make/Equivalent) 100 mm width x 60mm Height

Supply and fixing of 32 x 12.5 mm PVC Cable Management System with base and lid along with all accessories like external angle, internal angle, flat angle, end cap etc conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required and instructed by engineer in charge/consultant, including all accesories as required for complete installation. (OBO Betterman make or equivalent)

SPAN CONSTRUCTIONS

J and J ASSOCIATES

Lee Builders