COMPREHENSIVE REPAIR TO ROOF FALSE CEILING JOINERIES FLOORS BRICK WORK PLUMBING AND SANITARY FIXTURE PAVING FOOTPATH AND OTHER MISC REPAIRS IN NEW AND OLD DD LINE ESCORT LINE 9 CISU DPDO STN HQ AND EME AREA UNDER AGE B R I AT YOL CANTT

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of cement concrete (unreinforced) in above ground floor; exceeding 15 cm thick complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of brick work or stonework built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed

Taking down chowkats with shutters (without taking off shutters from chowkat) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from chowkat) exc 1.50 Sqm but not exc 4.00 Sqm each complete all as specified and directed. .

Taking down shutter of any description not exc 1 sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but not exc 2 sqm each complete all as specified and directed.

Taking down steel water tubing 15 mm bore including all fitting and connections complete all as specified and directed.

Taking down steel water tubing 20 mm bore including all fitting and connections complete all as specified and directed..

Dismantling timber in scantling 40 sqcm and over in section unframed work complete all as specified and directed.

Dismantling timber in scantling 40 sqcm and over in section framed work complete all as specified and directed.

Demolition of wall and ceiling boards any thickness including cover fillets complete all as specified and directed.

Dismantling plain or corrugated steel sheets any gauge thickness including Nanital or similar pattern roof covering including ridges complete all as specified and directed.

Hacking out old broken glass any thickness , size, quality or description from wooden/steel frame or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, complete all as specified.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises. complete all as specified and as directed.

Dismantling water storage tank of capacity exc 250 ltr but n.exc 500 ltr complete all as specified and directed. .

Dismantling water storage tank of capacity exc 500 litres but n.exc 1000 liters complete all as specified and directed. .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-1 (using 20mm graded crushed stone aggregates) as in hold fast block and similar work including use and waste of necessary form work complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

Extra for forming fair finished drain or channel n.exc 30 cm inner girth in cement concrete using extra cement including forms, moulds mitred / stopped ends etc complete all as specified and directed.

Add or deduct for each 25mm girth or part thereof over or under 30cm inner girth in cement concrete using extra cement including forms, moulds mitred / stopped ends etc complete all as specified and directed.

Precast cement concrete 1:2:4 ( nominal mix ) type B-0 (using 12.5 mm graded crushed stone aggregates) as in louvers and jallies, 40mm thick (measured solid) set in cement mortar (1:4), including all mouldings , frame including necessary formwork where required complete all as specified and directed.

Plain cement concrete 1:2:4 ( nominal mix ) type B-1 (using 20 mm graded crushed stone aggregates) as in copings and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork where required complete all as specified and directed.

RCC 1:1.5:3 (nominal mix) type A-1 (using 20 mm graded crushed stone aggregates ) as in slab and like complete all as specified and directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 (01 cement : 06 coarse sand) all as specified & directed.

All as per description of Srl item No 29 above but except bricks .

Brick work with old size fly ash bricks, class 7.5, as in half brick thick wall ,any radius, built in cement mortar 1:4 and pointed with same mortar as the work proceeds complete all as specified and directed.

Walling of random rubble stone masonry brought upto course well bonded bedded and soilidly hearted built in CM 1:6, complete all as specified and directed.

All as per srl item no 32 above but except stone.

2nd class hardwood (Sal) plain solid straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed

Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing of glass, particle board,aluminium frame etc complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II

Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 105 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified.

Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 125 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified.

35mm thick second class hardwood (Sal/Hollock) factory made plain framed panelled shutter (two panel) with lock rails & panel of 9 mm B.W.P commercial ply wood or 12 mm thick veneered particle board with commercial veneering on both side. The size of rail and stile as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

35 mm thick 2nd class hard wood (Sal/Hollock)) glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members of door shutters as specified in SSR- 2009 Part-I Section 8.24(a) complete all as specified and directed.

30 mm thick 2nd class hard wood (Sal/Hollock)) glazed & skeleton shutters open rebated and prepared to receive glass, gauze etc ( sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members of window shutters as specified in SSR- 2009 Part-I Section 8.24(b) complete all as specified and directed.

35mm thick flush shutters, solid core construction with particle board core and plywood face panels commercial type on both sides including 6mm thick external teak wood lipping complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, anodised aluminum snap beading screws etc. complete all as specified.

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07. Make : As per Appendix 'C'. Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Aluminium handles cast type anodized of size 125 mm complete all as specified and directed.

Aluminium handles cast type anodized of size 100 mm complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 150 mm and fixed complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 200 mm and fixed complete all as specified and directed.

200 mm long, prepainted steel type door spring heavy duty including roller and roller plate complete all as specified and directed.

200 mm long, prepainted steel type door spring heavy duty including roller and roller plate, fixed in repair complete all as specified and directed.

Aluminium (die cast) body ,door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair complete all as specified and directed.

Mild steel continuous (piano) hinges, bright finish or electrogalvanised of width flaps size 40mm (when open) complete all as specified and directed.

Fixed in repair brass mortice lock, 4 levers, vertical type, 100 mm size for doors all as specified.

Floor door stopper of 150mm long of alluminium alloy body and tongue, anodized with hard drawn steel spring, fixed in floor complete all as specified and directed.

Mild steel butt hinges of size 100 mm medium weight cold rolled complete all as specified and directed.

Mild steel butt hinges cold rolled medium weight of size 75 mm complete all as specified and directed.

Supply only mild steel butt hinges of size 50 mm medium weight cold rolled complete all as specified and directed.

Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed.

Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples, fixed in repair complete all as specified and directed.

Sheet glass, 3 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

Sheet glass, 4 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

Sheet glass, 4.8mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

3 mm thick, figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 mm and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete size of grid 605 x 605 mm all as specified and directed .

4 mm thick non asbestos fibre cement building boards (E-board classic) as in ceiling fixed or laid/ inserted to timber/ GI/ aluminium frame work fixed with nails, all as specified.

12 mm thick, Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame works all as specified and directed by Engr-in-Charge.

6mm thick external teak wood lipping on 18/19mm block board or veneered particle board complete all as specified & directed.

18/19mm particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified & directed.

2nd class hard wood as in weather boarding, wrought both sides and edges shot and chamfered (on exposed edges), plain, 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps, complete all as specified & directed.

2nd class hard wood, clean sawn, timber, unframed and fixed as in scantling complete all as specified and directed.

2nd class hard wood, wrought timber, unframed and fixed as in scantling complete all as specified and directed.

2nd class hard wood, wrought timber, framed and fixed as in scantling complete all as specified and directed.

0.63 mm thick CGI sheeting with nominal grade of zinc coating 120 gms per sqm with two corrugation side lap fixed with 'J' or 'L ' hooks as in roof covering,walls etc complete all as specified and directed.

All as per srl item no 77.00 above but except sheet with two corrugation side lap fixed with 'J' or 'L ' hooks as in roof covering, walls etc complete all as specified and directed.

0.80 mm thick plain, galvanised, mild steel sheeting as in ridges, hipe, valley gutters, drip and straight flashing (length and girth as fixed) with grade of zinc coating 120 gms per sqm complete all as specified and directed.

Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Prepainted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips, valley/ eaves/ rain water gutters, drip and straight flashing (length and girth as fixed), fixed with self tapping screws all as specified

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Rolled mild steel work as in main and cross beams, hips and jack rafter, purlins where connected to common rafters and running rails and guides for sliding doors ,fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde E-250) quality-A complete all as specified and directed.

Mild steel work as in hold fast, wind ties for roof including securing bolts including all necessary drilling ,bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in floor finish, surface finished even and smooth without using extra cement complete all as specified and directed.

Glass dividing strips 3 mm thick and width 38 mm inserted in position to conform to design complete all as specified and directed .

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

100 mm thick plain cement concrete 1:2:4 (nominal mix) type B-2 (using 40 mm graded crushed stone aggregates) as in hardstanding finished even and fair with spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

50 mm thick plain cement concrete 1:2:4 (nominal mix) type B-1 (using 20 mm graded crushed stone aggregate) as in repair to roof top padding, chajjas, roof projection etc., and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, mixed with water proofing admixture as per manufacturer's instructions, complete all as specified and directed. (Note:- WPC will be measured and paid separately)

Taking down of existing un-serviceable roof treatment materials including removing plaster, PCC padding etc complete from roof carefully by cutting chiseling, cleaning the surface by scraping brooming brushing etc and removing the rubbish from site complete all as directed .

10mm thick (average) screed bed/ plaster in cement mortar 1:3 in order to maintain proper slope and base over existing roof surface for laying of APP based polymeric membrane, mixed with integral water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete, all as specified and directed. (Note:- WPC and polymeric membrane shall be measured and paid separately).

Applying a coat of bitumen primer conforming to IS: 3384-1986 over plastered surfaces @ 0.40 litres/ Sqm of density 087-0.89kg/ litres at 25° C and viscosity 70-160 CPS (Bitumen primer shall be of same make as of membrane) including preparation of surfaces, complete all as specified & directed.

APP (atactic Poly-propylene polymer) modified membranes, five layered, 3mm thick weighing not less than 3.6 kg/Sqm, having a centre core of polyester non-woven mat (FP) reinforcement dipped into APP modified mix and sealing all the over laps 75mm on length side and 100mm on width side of membranes by torching as per manufacture's instructions by authorised applicator only after applying evenly a coat of bitumen 85/25 grade @1.2kg per sqm on the bottom of APP and on top of joints of APP complete all as specified.

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor finish, surface finished even and fair to receive top finish complete all as specified and directed.

Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic coloured tiles of size 450 mm x 350 mm x 7 mm/350 mm x 250 mm x 7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE.

Glazed ceramic coloured tiles of size 300mm x 200 mm x 7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the GE.

Vitrified ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm as directed by EIC, as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Vitrified ceramic tiles (light shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm as directed by EIC, as in vertical surfaces , set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick cement screed in cement mortar 1:4 complete all as specified and directed. .

14 to 16mm thick, machine cut , marble slab as in kitchen plateform/ shelf/vertical faces, over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the marble slab including rubbing / grinding & mirror finish polishing / granite polishing over and including 15 mm thick screed base in cement mortar 1:6 over and complete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over and including 50mm thick sand cushioning, joints of tiles filled with dry sand and compacted with mechanical vibrator over and including 75mm thick PCC M-10 (Nominal Mix) type C-2, using 40mm graded crushed stone aggregate complete all as specified and directed.

Chequered cement concrete coloured tiles, homogenious texture glossy finished , chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 complete all as specified and as directed. Shade/Colour of tile shall be approved by the GE.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on stone masonry surfaces, mixed with water proofing admixture as per manufacturer's instructions, trowelled to even and smooth finish without using extra cement complete all as specified. (Note:- WPC will be measured and paid separately)

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on stone masonry or surface other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling , chajjas, fin, facias etc and including applying cement slurry; surface finished even & smooth without using extra cement complete all as specified and directed .

Supply only liquid water proofing admixture.

Preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint complete all as specified and directed.

Preparing surfaces of wood & wood based surfaces new or old of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified and directed.

Preparation of wooden surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old ,ends of post and backs of chowkhats etc., area exceeding 0.10 Sqm and not exceeding 0.5 Sqm each and treating with tar or coal tar black paint all as specified.

All as per Ser Item No 116 here-in- before but treating small articles such as gully, grating, hold fast, back of chowkhats etc., area not exceeding 0.1 Sqm each.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Two coats of white wash on newly plastered or un plastered, previously undecorated walls surfaces including preparation of surfaces complete, all as specified.

Two coats of white wash on newly plastered or un plastered, previously undecorated ceiling surfaces including preparation of surfaces complete, all as specified.

Preparation of new plastered surfaces or un plastered, previously undecorated wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

G I tubing medium grade of 15 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor/trenches complete all as specified and directed.

All as per ser item No 122 above but except pipe including new fittings as per requirement .

G I tubing medium grade of 20 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

All as per ser item No 124 above but except pipe including new fittings as per requirement .

G I tubing medium grade of 50 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

Cutting chases, pinning in. making good to facings here required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good complete all as specified.

Steel plate rack made of stainless steel having thickness 0.80 mm, fixed with plugs, washers and steel screws including bedding in cement mortar on to dwarf wall, overall size 600mm x 750mm X 250 mm, all as specified and directed.

Sink with drainage board (glossy) made of high grade stainless steel 1 mm thick with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x510 mm and bowl size 600mmx450mm x 225mm, fixed in repair complete all as specified and directed.

Mild steel curtain rod, 25 mm bore, powder coated with all fittings i.e. wall bracket, bracket screws & stope, fixed in repairs all as specified.

Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges fixed in repairs with and including chromium plated brass brackets, brass screws complete all as specified

Chromium plated soap dish, fixed in repair complete all as specified.

PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and directed.

Wash basins, Vitreous China (Flat white type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make: Cat Part No. 1008 of Cera or equivalent in makes mentioned in Appx 'C'

Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (including fixing bolts, flush pipe, PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 7.0 litres), with grating and union for discharge pipe, flush pipe and waste pipe, Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, complete all as specified and as directed.

Pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe of bore 15 mm, fixed in repair complete all as specified and directed

Stop valves/ angle valve/ concealed valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure , screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. Type of valve approved by the GE.

Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair, complete all as specified and directed.

Gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed bore dia of pipe 20 mm, fixed in repair, complete all as specified and directed.

Gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed bore dia of pipe 25mm, fixed in repair, complete all as specified and directed.

Chromium plated shower jet spray hygenic spray set with 15mm dia, 1m long tube, fixed in repair, complete all as specified.

Chromium plated shower rose, 125mm size, fixed in repair, complete all as specified.

Vitreous china wash down water closet (Pedestal pattern) white with seat cover with all fittings including connection to drain and to flushing pipe , anti syphonage pipe etc complete all as specified and directed.

PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, in repairs, all as specified. Make: Cat Part No. 2602 of Cera or equivalent in makes mentioned in Appx 'C'.

Fixed in repair, 600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc and making good to floors to match existing, in repairs, all as specified. Make: Cat Part No. 2071 of 'Cera' or equivalent makes mentioned in Appx 'C'.

Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, fixed in repair complete all as specified and directed.

40mm bore, high density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm complete all as specified and directed.

Fixed in repair, PVC cabinet of size 350 x 450mm with shelf assembly mirror mounted as shutter complete all as directed.

110mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to trenches or in floor or walls ,fixed in repair complete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to trenches or in floor or walls, fixed in repair complete all as specified and directed.

110 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement, fixed in repair complete all as specified and directed.

110mm dia PVC (SWR) junction single, (single T) equal or unequal provided with oval access door, fixed in repair complete all as specified and directed.

75mm dia PVC (SWR) junction single, (single T) equal or unequal provided with oval access door, fixed in repair complete all as specified and directed.

110 mm dia PVC(SWR) vent cowl, fixed in repair complete all as specified and directed.

75mm dia PVC(SWR) nahani trap plain with grating including jointing with solvent cement, fixed in repair complete all as specified and directed.

CP grating for 100/110 mm bore cast iron nahani trap, fixed in repair complete all as specified.

Disconnecting existing tank any type of capacity exc 500 litre and not exc 1000 litre, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position omplete all as specified and directed.

Disconnecting existing tank any type of capacity exc 250 litre and not exc 500 litre, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Nipple 20mm suitable for HDPE water tank fixed in repair complete all as specified and directed. (Minimum weight 20mm- 45gms )

Nipple 25mm suitable for HDPE water tank fixed in repair complete all as specified and directed. (Minimum weight 25mm- 65gms)

Cutting and uprooting vegitation growth/plants of any size on roof surfaces or chajja including making good surface and including muds and disposal of unserviceable material to a distance not exceeding 100m complete all as specified and directed.

Tank cover for 500/1000litres water tank, made out of 2mm thick sheet of mild steel , circular in shape having dia 0.45m with border of cover made out of mild steel sheet 25mm wide and 1mm thick, welded around the cover at 90degree with sharp tip nails (10 nos) of 5cm length, welded on top of cover for protection from monkeys with locking arrangement comprising 04 nos flat iron pieces (25mm x 2 mm) flat iron of suitable length duly drilled and welded with tank and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

20 mm dia, ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed in repair complete all as specified and directed. (Minimum weight 210gms)

10 mm dia, AQUA TP aluminium grouting nipple upto 75mm to 100mm deep by drilling with 12mm bore hole and fixing in cement mortar at 600mm above skirting /junction/trapa and gravity @10-12 kg/sqm pressure using grouting pump complete all as specified and directed.

Vent for moisture release for wall more than 100mm thick and applying AQUAVENT complete all as specified and directed. Make :-AQUAVENT25100A or equivalent make as approved by the GE.

Vent for moisture release for wall more than 100mm thick and applying AQUAVENT complete all as specified and directed. Make :-AQUAVENT2050P or equivalent make as approved by the GE.

jatindera enterprises

Ms Sunil Kumar