Supply, installation, testing, and commissioning of fire fighting system at NSC Jayant including automatic FDAS, automatic sprinkler and wet riser cum down comer including three year CAMC after completion of 02 years warranty period

Amount

Providing laying, testing and commissioning of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, reducer, jointing with nuts bolts, gaskets and welding etc. and fixing the pipe on wall/ceiling with suitable hangers, clamps, supports, as required and painting with two or more coats of synthetic. Enamel paint of required shade complete as directed by Engineering-in-Charge. (i) 200 mm

(iii) 100 mm

(iii) 80 mm

Supplying, installation, testing & commissioning of approved make horizontally mounted coupled motor (Eff-1) 60hp, 2900 RPM, 3 Ph 415 V with mechanical seal pump delivery of 2280 litres per minute against total head of 70 meter so as to ensure a minimum pressure of 3.5Kg/Cm2 at the highest .The impeller shall be closed type and accurately balanced dynamically. The pump shall be of castiron, impeller shall be of bronze and shaft shall be of stainless steel, automatic air release valve, pressure gauges (combination suction gauge, 3½”dial type with ¼” cock and lever handle - 1no ,discharge gauge, 3½”dial type with ¼” cock and lever handle-1 no.) including coupling, coupling guard, base channel foundation & matching flanges etc. as required as per specifications .The firepump set as per NFPA –20 specifications.

Supplying & installation of approved make diesel engine driven fire fighting pump water cooled 65BHP 2150 RPM engine, fuel tank 200 Ltr (empty), accesMP SORies, matching flanges, base frame, ARV , fuel gauge, 12 Volt battery & charger ,lugs & cable between battery & charger. The pump capacityof 2280 litres per minute at total head 70 meters, automatic air release valve, pressure gauges (combination suction gauge, 3½”dial type with¼” cock and lever handle-1 no, discharge gauge, 3½” dial type with ¼” cock and lever handle-1 no.) as required . All above equipment's are mounted on common baseplate.The fire pump set as per NFPA –20 specifications.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operationandconsistingof following, complete inall respects, as required: (Terrace Pump) (a)Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3phase, 50Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c)M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d)Suitable cement concrete foundation duly plastered and with anti vibration pads. (i) 900LPM at 35m head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type,multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. SuitableHPsquirell cage inductionmotorTEFCtype suitable for operationon415volts, 3phase 50Hz ACsupplywithIP55classofprotectionforenclosure, horizontal footmounted type with Class-'F' insulation, conforming to IS : 325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. (i) 180 LPM at 70m head

Providing and fixing single headed hydrant valve with instantaneous female Gun metal couplings ofrequired dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank gunmetal cap and chain,adopter as required complete as directed by Engineer-in-Charge. 63mm dia

Providing and fixing first -Aid hosereel with MS construction spray painted in post office red, confirming to IS 884 with up to date amendments,complete with the following asrequired.) (a) 30-36m long 20mm (nominal internal) dia water hose thermoplastic (textile reinforced ) type -2 as per IS 12585 (b) 20mm (nominal internal) dia gun metal globe valve and nozzle. (c) Drum and brakets for fixing the equipments on wall. (d) Connections from riser with 40 mm dia stop valve (gun metal) and M.S. pipe

Providing and fixing 63mm gun metal branch pipe with 20mm (nominal internal diameter)size gun metal nozzle conforming to IS 903, suitable for instantaneous connection, to interconnect hose pipe coupling as required.

Providing and fixing flow switches in 100/150 mm dia MS pipe. Capacity 5.0 kg.

Supplying and fixing 63 mm dia, 15m long, RRL hose pipe with following diamale and female gun metal couplings duly binded with GI wire, rivets etc. confirming to IS 636 (type-A)as required.

Providing and fixing hose cabinet of size 900x600x500 mm made of 2 mm thick MS sheet with 4 mm thick float glass doors in front painted "FIRE" in red paint i/c necessary locking arrangement suitable to accommodate external hydrant with butterfly valve 2 nos. 15m Long hose pipe, 1 no branch pipe mounted on wall or raised brick platform& duly painted with post office red externally and white internally with synthetic enamel paint complete in all respects for external hydrant, as directed by Engineer-in- Charge.

Providing and fixing 4way fire brigade connection (FBC)of cast iron body with 4 nos. gun metal male instantaneous inlet couplings complete with cap and chain as required. For 150mm dia MS pipe connection, confirming to IS 904 as required.

Providing, fixing, testing and commissioning of butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, confirming to IS 13095, of following sizes as required. (a) 200mm dia

b)150mm dia

c)100mm dia

d) 80mm dia

e) 65mm dia

f) 50mm dia

Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. a) 200 mm dia

b) 150 mm dia

c) 100 mm dia

d) 80mm dia

Supplying & installation of pressure gauges with15mm dia brass check nut & capable of showing pressure reading from (0 to 30 kg).

Supplying & installation of approved make pressure switch with 15 mm dia brass check nut for automatic operation on required pressure including necessary wiring up to control panel.

Supply, installation, testing and commissioning of ball valve (brass) high or low pressure with plastic floats inclusive of all necessary required material, labor for mentioned below size. 25mm OD

Providing & Fixing of spring loaded Air Release Valve suitable for pressure of 15 Kg/sq.cm including flanges, nuts, bolts, washers etc. complete as required.

Providing and fixing air vessel made of 250mm dia, 8mm thick MS sheet, 1200mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia Gunmetal wheel valve, with required accesMP SORies, pressure guage and painting with synthetic enamel paint of approved shade as required .

Supplying, fabricating, STRUCTURAL STEEL SUPPORTS such as MS channels, angles, flats, rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete with painting.

Providing, installation, testing and commissioning stainless steel strainer fabricated out of 1.6 mm thick stainless steel sheet with 3 mm dia holes with stainless steel flange. (i) 150mm Dia.

(ii) 100 mm Dia

Fire panel : Providing, fixing, testing & commissioning microprocesMP SOR based main fire alarm panel and indicating panel solid state modular card type pulsar, timer for dual stage alarm facility with indicators, standby battery ,complies to IS 2189:1999.2 x 16 character backlit LCD display lamp test features. Complete with integral power supply and battery charger for SMF battery. NO/NC contacts for both fire and fault. Switches to enable on board operation. LCD and LED Indication for open, short circuit, Isolate, fire in each zone. reset, lamp test, silence, isolate, short, open, fire continuous buzzer for fault and intermittent buzzer for fire battery charger box, operating voltage 220 Volt mains A.C. input/24V D.C. output etc. complete in all respect (including all wiring work). (i) 24 zones fire panel

Supply installation testing & commissioning of heat detector operating at 54°C/57°C with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as requiered.

Supply installation testing & commissioning of Smoke detector with built in LED and mounting base complete with all connection etc. as requiered.

Manual call point: Providing & fixing of manual calls point flush or surface mounting. Front protection glass cover. Unbreakable glass ABS plastic body.

Control Module

Providing & fixing of internal hooter with working AC Voltage 220V A.C./24V D.C.current consumption,sound output 120 DB, material M.S. sheet.

Providing, fixing testing and commissioning of 15mm sizequartzoid bulb type sprinklers, set to operate at 68/79 degree Centigrade. Pendent type/upright type/side wall type with required accesMP SORies complete as directed by Engineer-in- Charge.

(i)Rubber Valve - 150mm

(ii)Rubber Valve - 100mm

Providing, fixing, testing and commissioning of installation control valve of Cast iron body and brass/bronze working parts comprising of water motor alarm, bronze seat clapper, and clapper arm, hydraulically driven mechanical going bell to sound continuous alarm when the Wet riser/Sprinkler system activates, pressure gauges, emergency, releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ballvalves, MS pipe of required sizeflanges, orifice plate, gasket etc. of size 150 mm dia and obtaining NOC from local bodies etc required.

R.I. : Providing & fixing of response indicator

Minor civil related jobs like pedestals, platforms for motors, core cutting, water inlet pipe to pump house, cabling, excavation, dismantling of false ceiling and re-installing of false ceiling as per requirement. etc .

For dismantling of existing Fire detection system and charges for safe upkeeping of outside NSC hospital building after dismantling

1st year CAMC charges after two year warranty

2nd year CAMC charges after two year warranty

3rd year CAMC charges after two year warranty

Total impact of GST for the purpose of CTC

J.K. DEFENCE FIRE ENGG. SERVICES