Renovation of D.T.O. and Deputy Director Office building at Dharamshala, in District Kangra, (Himachal Pradesh)

Amount

Demolition un-reinforced cement concrete more than 15cm (fifteen centimetre) thickness above G.L. upto all floor level including disposal of unserviceable materials within all leads as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete 1:6:12 (One cement isto Six sand isto Twelve graded broken/crushed stone aggregate 40mm (Forty millimeters) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying 600 x 600 x 10 mm (Six hundred into six hundred into ten millimetres) antiskid vitrified ultra charged tiles of nitco / rak/ Kajaria/ orient and bell as per approved shade in flooring treads of steps and landings laid on a bed of 12mm (Twelve milimetres) thick cement mortar 1:3 (One cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment to required shade to match the shade of tiles complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Dismantling G.I. Sheet roofing including ridges, hips, valleys, gutters etc. stacking the serviceable materials and disposal of un-serviceable materials within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet of Tata durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six milimetres) diametres with prepainted limpet and rubber washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification and as directed by the Engineer-in-Charge

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all width 0.60mm (Zero decimal Sixty millimetres) thick prepainted steel sheet Tata durashine of approved make in ridges (Factory made) shall be having proper Gola/Shape of steel sheet Tata/ Sakti or equivalent with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge

Providing and fixing valleys 90 cm (ninety centimetres) over all width 0.60mm (Zero decimal Six zero milimetres) thick prepainted sheet Tata durashine in roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (five) micron primer coating, back coat of polyster of 5 (Five) microns including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing 0.63mm (zero decimal six three) thick sheet 15 cm (fifteen centimetre) wide 45 cm (forty five centimetre) overall semicircular plain G.I. (galvanised iron) sheet gutter with iron brackets 40x3mm (forty into three millimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing on wall face 110mm (One hundred ten milimetres) diametres P.V.C. rain water pipes of working pressure 4.5kg / sqm (four decimal five kilogramme per square metre) as per ISI finolex / Ralpipe / vectos pipe confirming to IS code 13592 for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals, and as directed by the Engineer-in-Charge.

Providing and fixing 150mm (One hundred fifty milimtres) diametres PVC Plain bend on wall face P.V.C. acessories for rain water pipes of working pressure 4.5kg / sqm (four decimal five kilogramme per square metre) as per ISI finolex / Ralpipe / vectos confirming to IS code 13592 for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge

Providing and fixing plain M.S. B.P. iron sheet 2mm (Two milimetres) thick fixed in eaves board / facia / soffits / ceiling including cutting, fixing and jointing with gas/ electric welding in position complete (frame work is to be measured and paid for separately within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

Dismantling doors, windows and clerestory windows, ventilators etc. (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachements etc. complete and stacking them within all leads Not exceeding 3 (three) sq.m in area within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge

Providing and fixing powder coated (50 - 60 microns) aluminium work for door, window, ventilators and partitions frames in approved colour / shades with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazing/ panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and the directions of Engineer-In-Charge within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and Fixing aluminium composite pannel sheet as per architectural drawings and the directions of Engineer-In-Charge For doors windows and ventilatiors and glazed partitions frames within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

Steel work welded in built up sections including hollow steel sections in trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint in beams, joists, channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters, purlins connected to common rafters and the like within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 5mm (five millimetre) thick plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 40mm (forty millimetres) thick second class deodar wood, panelled glazed or panelled and glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws, within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 40mm (Forty milimetres) thick second class deodar wood wire gauge shutters using galvanized M.S. wire gauge of IS gauge designation 85 G with wire of 0.56mm (Zero decimal five six milimetres) diameters for doors, windows and clerestory windows including bright finished /black enameled iron hinges with screws within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final finish to the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Removing dry or oil bound distemper by washing and scraping and sand papering the wall surface smooth including necessary repairs to scratches complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

Painting one coat (excluding priming coat) with white enemal paint on previously painted wood and wood based surfaces with enamel paint to given and even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

Painting one coat (excluding priming coat) with white enamel paint on previously painted steel and othermetal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt,dust and other foreign matter within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

Finishing walls with weather proof exterior grade emulsion of approved design (apexultima) on un decorated wall surfaces( two coats) to give an even shade and final finish after throughly brushing the surface clean of all dirt, dust, loose pieces of scales and also including preparing the surface even and sand papered smooth complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing aluminium Pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with necessary screws etc.Tower bolts (Barrel type) as approved drawing, design and as directed by the Engineer-in-Charge.

300x10mm (three hundred into Ten milimetres) size

150x10mm (One hundred fifty into Ten milimetres) size

Providing and fixing aluminium Pilot/sheel or equivalent anodized transparent or dyed to required colour and shade and of approved make with necessary screws etc. handles with the necessary screws etc. complete. within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.

100mm (One hundred milimetres) size

125mm (One hundred twenty five milimetres) size

Providing and Fixing stainless steel bench for sitting make of kamdenu or its equivalent within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge

Providing and Fixing wooden board cabin including table with vertical glass fixed in cabin. The size of cabin 1.20x0.75x0.75 (one decimal two zero into zero decimal seven five into zero decimal seven five) with wall fininsed within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge

PARDEEP KUMAR