Construction of one room with washroom water tank, Septic Tank and Repair/ renovation of office of Fleece Testing Officer Kartholi

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) in trenches, foundation, drains pipes cable etc. in all classification of soils and disposal of excavated earth and refilling the available excavated earth behind trenches or wherever required incl. levelling, dressing, ramming, watering and rolling etc. as per directions of Engineer-in-charge with all leads / lifts and carriage complete job.

Providing and Laying in position cement concrete of specified grade excluding the cost of centring and shuttering – All work upto plinth level a) 1:5:10 (1 cement : 5 coarse sand : 10 graded crushed stone aggregate 40mm nominal size) with all leads and lift carriage complete

b) 1: 3: 6: ( 1: cement 3: coarse sand : 6 graded crushed stone aggregate 20mm nominal size, with all leads and lift carriage complete.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing & reinforcement. All work upto plinth level 1: 1.5 : 3 ( 1 : cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size. with all leads and lift carriage complete.

Providing and Laying damp – proof course 50mm flooring with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 grade crushed stone aggregate 20mm nominal size) with all leads and lift carriage complete.

Supply and laying of River Bed Materials including leveling, dressing, watering & consolidation in layer 20cm in depth each layer consolidated with power road roller of minimum 8 tonne capacity incl. carriages complete,

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in, Cement mortar 1:6 ( 1 cement : 6 coarse sand) with all leads and lift carriage complete.

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level, with all leads and lift carriage complete.

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand) with all leads and lift carriage complete.

Extra for half Brick masonry in superstructure above plinth level upto floor V level, with all leads and lift carriage complete.

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 ( 1 cement : 4 fine sand), with all leads and lift carriage complete.

18mm Cement plaster in two coats under layer 12mm thick cement plaster 1 : 5 (1 cement : 5 coarse sand) finished with a top layer 6mm thick cement plaster 1 : 3 (1 cement : 3 coarse sand) finished rough with sponge, with all leads and lift carriage complete.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete, with all leads and lift carriage complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately), Second class deodar wood

Providing and fixing 35mm thick glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, Second class deodar wood

Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge, Second class deodar wood

Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete, With Galvanized M.S. Wire gauge with wire of dia 0.63 mm With 2nd class teak wood beading 62x19 mm

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of 12 mm thick plain grade-I, medium density flat pressed three layer particle board FPT-I or graded wood particle board FPT-I, IS: 3087 marked, bonded with BWP type synthetic resin adhesive as per IS: 848

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Reinforcement for RCC work including straightening, cutting bending placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centring and shuttering including strutting, propping etc. and removal of form work for:- a) Foundations, footings, bases of Columns.

b) Suspended floors, roofs, landings, balconies and access platform.

c) Edges of slabs and breaks in floors and walls Under 20 cm wide

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead For thickness of tiles above 25 mm and upto 40 mm.

Painting top of roofs with bitumen of approved quality at 17 kg per 10sqm impregnated with a cost of coarse sand at 60 cudm per 10 sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete, with residual type petroleum bitumen of grade VG-10

Providing and laying on terrace mud phuska to proper slope mud plaster gobri leaping on top of terrace, Complete Job

Providing and laying pressed clay tiles (as per approved pattern 20mm nominal thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound laid over a bed of 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) and finished neat complete, with all leads and lift carriage complete.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately) Size of tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete, Size of tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture over and including a priming coat of ready mixed zinc chromate yellow primer on new work, 75 mm diameter pipe.

Providing and fixing aluminium works for doors, windows, ventilators and in partitions with extrusted built up section standard tobular section of approved Z-section and other sections of approved make with desh fasternar of required dia and size incl. necessary filling up of gaps and junctions i.e at Top bottom, side with required EPDM rubber aluminium section should be smooth, dust free, straight aluminium snap beading for glazing, panneling, C.P brass etc. all complete ( 14 gauge )

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade, one or more coats on old work

Polishing on wood work with readymade wax polish of approved brand and manufacture on old work.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work, over and including water thinnable priming coat to give an even shade

Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade

Finishing walls with water proofing cement paint of required shade Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat.

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand), Ordinary cement without any pigment.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete, with all leads and lift carriage complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge, Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Renewing glass panes, with putty and nails wherever necessary including raking out old putty, Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm)

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in- charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required, 510x1040mm bowl depth 250mm

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required, White glazed fire clay kitchen sink of size 600x450x250 mm

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 18.2.1 W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete, Flexible pipe 40 mm dia

Providing and fixing 100 mm sand cast iron grating for gully trap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour, 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer,

Providing and fixing plain panelling with skirting chair rails and cornice with necessary screws, priming coat on unexposed surface etc. complete ( Second class deodar wood with 25mm thick )

Mohd Rafeeq