Construction of Block-B of Additional Accommodation Govt. Senior Secondary School Bagsaid in Tehsil Thunag Distt Mandi SH C/o Building portion WS and SI Septic tank and site development

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm (thirty centimetre) in depth, 1.5 m (one point five metre) in width as well as 10 sqm (ten squaremetre) on plan in all kinds of soil including getting out and disposal of excavated earth upto any lead , as directed by Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within any lead in all kinds of soil including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position cement concrete 1:3:6 (one cement : three coarse sand : six graded stone aggregate 40 mm (fourty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (one Cement : four coarse sand) : eight graded stone aggregate 40 mm(fourty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm (fourty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm (twenty millimetre) nominal size over 75mm(seventy five millimetre) thick bed of dry brick ballast 40 mm (fourty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20 mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° ( fifteen degree) landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level in 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate) 20 mm (twenty millimetre nominal size) up to floor five level , excluding cost of centering, shuttering, finishing and reinforcement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, sqm etc. for mass concrete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and acceess platform including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, sqm bressumers and cantilevers including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiralstaircases. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Centering and shuttering including strutting, propping etc. and removal of form for Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Steel reinforcement for R.C.C. work in Thermo-Mechanically Treated bars of grade Fe-500D or more including straightening, cutting, bending, placing in position and binding all complete above plinth level complete up to any level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying in position machine batched and machine mixed design mix M-25 (M- twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability upto plinth level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and laying in position machine batched and machine mixed design mix M-25 (M- twenty five) grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability upto all floor level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (one cement : six coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5(seven point five) in Cement mortar 1:4 (one cement :four coarse sand) superstructure above plinth level up to floor V level. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including levellingup with cement concrete 1:6:12 (1 cement : 6 Sand : 12 Graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1cement:6 sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Stone soling/boulder filling dry hand packed in under floor , Stone filling behind abutment wing wall and retainling wall including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 18 mm (eighteen millimeter) thick granite of any colour and shade having area of slab over 0.50 sqm (zero point five squaremeter) gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimeter) thick base cement mortar 1:4 (one cement : four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm (twelve millimeter) thick bed of cement mortar 1:3 (one cement : three coarse sand) and jointing with grey cement slurry @ 3.3kg (three point three kilogram) per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position 2nd (Second) class deodar wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing wood work in frames of false celling partitions etc. sawn and fixed in position 2nd (Second)class Sal wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm (Thirty five millimetre) thick including ISI marked Stainless Steel butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 40 mm (Forty millimtre) thick double glazed shutters for doors, windows and clerestory windows using 2(Two) number 5 mm (Five millimetre) thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. complete as per specification and including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing double glazing (doubleglass ) fixed in wooden window ventilator shutters and partition rtc with wooden corner or wooden bead in teak wood bead etc. of required size with nails mitred and jointing complete and glazing with glass panes of 5 mm (Five millimetre) thick including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 40 mm (forty millimetre) thick 2nd (Second) class deodar wood wire gauge shutters using galvanised M.S. wire gaugeof average width of aperture 1.4 mm (one point four millimetre) in both directions with wire of dia 0.63 mm (zero point six three millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 18 mm (eighteen millimetre) thick, 150 mm (One hundred fifty millimetre) wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm (Six millimetre)coir veneer board, nickle plated M.S. Pipe 20 mm (Twenty millimetre) dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25 x3 mm (Twenty five x three millimetre) M.S. Flat 10 cm (Ten Centimetre) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm (One hundred millimetre x forty millimetre x forty millimetre) on both inner side of pelmet and rawl plugs 75 mm (Seventy Five millimetre) long etc. all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing Plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing 40x5 mm(Forty x five millimetre ) flat iron hold fast 40cm. (Forty centimetre ) long including fixing to frame with 10mm (Ten millimetre ) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm.(Thirty x ten x fifteen centimetre ) 1:3:6 ( One cement : three sand: six graded /crushed stone aggregate 20mm(Twenty millimetre ) nominal size within all leads and lift including carriage of material in all respect and as per direction of Engineer-in-charge.

Providing and fixing 75 mm x60mm (seventy five millimetre x sixty millimetre) hand rail in straight length complete in First class Indian teak wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing aluminium sliding door bolts,300x16 mm (three hundred x sixteen millimetre) ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. completeincluding carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 250x10mm (Two hundred fifty x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 125 mm (One hundred twenty five millimeter)

100 mm (One hundred millimeter)

Providing and fixing aluminium hanging Twin rubber floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 150 mm (One hundred fifty millimetre) bright finished brass hasp and staple (safety type) with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ISI marked 150 mm (One hundred fifty millimetre) oxidised M.S. single acting spring hinges with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 150 mm (One hundred fifty millimetre) oxidised M.S. double acting spring hinges with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing in wall lining 12 mm thick (Twelve millimetre0 medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. completeincluding carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 25mm (Twenty five millimetre) thick pre-laminated medium density fibre board exterior grade ( Grade-I) IS:14587:1998 marked with one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm (Two millimetre) thick of approved brand including ISI marked nickel plated bright finishing M.S. piano hinges conforming to IS:3818 marked with necessary screw etc all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 19 mm (ninteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cup board / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from out side shall be finished with 4 mm (four millimetre) thick vaneer Ply of approved shade to match with panelling including stainless steel hinges hinges and magnetic catcher with in all accessories etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Steel work welded in built up sections in trusses and trussed purlins in buildings including cutting, hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Steel work welded in built up sections in Gratings framed guard bars ladders railing brackets and similar works including cutting, hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm (thirty five into thirty five into five millimetre) , joints mitred and welded by angle iron 35x35x5 mm (thirty five into thirty five into five millimetre) or 35x 5 mm (thirty five into five millimetre) flat pieces to the existing T iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Kota stone slab flooring 25 mm (Twenty five millimetre) thick over 20 mm (Twenty millimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (One cement : four coarse sand) complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Kota stone slabs 20 mm (Twenty millimetre) thick in risers of steps, skirting, dado and pillars laid on 12 mm (Twelve millimetre) (average) thick cement mortar 1:3 (One cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

25 mm (Twenty five millimetre) wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with 2nd class deodar wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying full body vitrified floor tiles of AGL/Johnson/Kajaria/Orient Bell or equivalant in size 600x600mmx10mm ( six hundred into six hundred into ten millimetre) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying full body vitrified floor tiles of AGL/Johnson/Kajaria/Orient Bell or equivalant in size 600x600mmx10mm ( six hundred into six hundred into ten millimetre) with water absorption less than 0.08 % and conforming to I.S.15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing valley 90 cm (ninety centimetre overall 0.60mm (Zero six zero milimetre)thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat og regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with screws, preprinted iron J and L hooks,bplts & nuts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing M.S. BP Sheet 1.66 mm (One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and Fixing 15 mm (Fifteen millimetre) thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm (five hundred ninty five x five hundred ninty five) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams (One hundred twenty) per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm (Twenty four x Thirty eight millimetre) made from 0.33 mm (zero point Thirty three millimetre)thick (minimum) sheet, spaced 1200 mm (One thousand two hundred millimetre) centre to centre, and cross “T” of size 24x28 mm (Twenty four x Thirty eight millimetre) made out of 0.33 mm (zero point Thirty three millimetre) (Minimum) sheet, 1200 mm (One thousand two hundred millimetre) long spaced between main’T’ at 600 mm (Six hunderd millimetre) centre to centre to form a grid of 1200x600 mm (One thousand two hundred x six hundred millimetre)and secondary cross ‘T’ of length 600 mm( six hundred millimetre)and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm (One thousand two hundred x six hundred millimetre) panel to from grid of size 600x600 mm, (six hundred x six hundred millimetre )resting on periphery walls /partitions on a Perimeter wall angle precoated steel of size(24x24X3000 mm(Twenty four x twenty four x three thousand millimetre) made of 0.40 mm (Zero point forty millimetre) thick (minimum) sheet with the help of rawl plugs at 450 mm ( Four hundred fifty millimetre) centre to centre with 25 mm (Twenty five millimetre) long dry wall screws @ 230 mm (Two huundred thirty millimetre) interval and laying 15 mm (Fifteen millimetre) thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm (Twenty five x thirty five x one point six millimetre) fixed to ceiling with 12.5 mm (Twelve point five millimetre) dia and 50 mm (Fifty millimetre) long dash fasteners, 4 mm (Four millimetre) G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, (Eighty five x thirty x zero point eight millimetre) spaced at 1200 mm (One thousand two hundred millimetre) centre to centre along main ‘T’, bottom exposed with 24 mm (Twenty four millimetre) of all Tsections shall be prepainted with polyster baked paint, for all heights, as per specifications, drawings and complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:4 (one cement: four sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying 6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including water thinable priming coat with cement primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying white cement based putty of average thickness 1.00 mm (one millimeter) of approved brand and manufacture over the over plaster wall surfaceto prepare the surface evean and smooth complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Wall painting with acrylic emulsion paint having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth as required for making the surface including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour on steel work to give an even shade one or more coats including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm (fifteen into twenty centimetre) in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm (fourty millimetre) nominal size and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty millimetre) nominal size and finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing one side green board (Chalk writing) and other side white board (Marker writing) in class rooms enabling writing with chalk and marker and fixed on walls with necessary screwes etc.complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing bright finished hard drawn hooks and eyes 150 mm (one hundred fifty millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing weep hole in brick masonry/ stone masonry / plain reinforced concrete abutment, wing wall, return wall with 100mm dia.(one hundred millimetre diametre) PVC pipe extending through the full width of the structures with slope of 1V:20H (one vertical isto twenty horizontal) towards drawing face complete as per drawing and technical specifications clauses 614,709,1204.3.7 including carriage of material and other incidentials as per the direction of the Engineer-in Charge .

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 (Thirty) grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete including carriage of material and other incidentials as per the direction of the Engineer-in Charge .

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) W.C. pan with ISI marked white solid plastic saet and lid, 10 litre (Ten) low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required all complete including carriage of material and other incidentials as per the direction of the Engineer-in Charge .

Providing and fixing White Vitreous China Wash basin size 550x400 mm (Five hundred fifty x four hundred millimetre) with a pair of 15 mm (Fifteen millimetre) C.P. brass pillar taps, C.P.wash basin with C.I. brackets, 32 mm (Thirty Two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required all complete including carriage of material and other incidentials as per the direction of the Engineer-in Charge .

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings & making good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm (Forty millimetre) including painting of fittings and brackets, cutting and making good the walls wherever required with drain board of size 510x1040 mm (Five hundred ten x One thousand forty millimetre) bowl depth 225mm (Two hundred twenty five millimetre) & making good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 8 mm (eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 metre (one metre) long with S.S. triangular plate to Eureopean type W.C. of quality including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm (Four hundred thirty x two hundred sixty x three hundred fifty millimetre) or 340x410x265 mm (Three hundred forty x four hundred ten x two hundred sixty five millimetre) sizes respectively & making good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32mm (Thirty two millimetre) dia including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing CP brass toilet paper holder including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT 15 mm (Fifteen millimetre) Urinal spreader size 95x69x100 mm (Ninty five x sixty nine x One hundred Millimetre) with 1/2" (One by Two) BSP thread and shapes, weighing not less than 60 gms (Sixty grams) complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre (one metre) spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 1216 OD pipe 16 mm (sixteen millimetre) .

1620 OD pipe 20 mm (twenty millimetre) .

Providing and fixing 20 mm (twenty millimetre) nominal bore mild steel tube (medium grade) tube fittings with G.I. fittings including trenching and refilling etc. external work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm (fourty five centimetre) length 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing C.P. brass stop cock concealed of standard design and of approved make conforming to IS:8931. 15 mm (Fifteen millimetre) nominal bore complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm (Fifteen millimetre) nominal bore complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Circular type 100 mm (One hundred millimetre) nominal dia PTMT grating of approved quality and colour complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (One hundred Thirty eight millimetre), breadth 102mm (One hundred two millimetre), height of 75mm (Seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms (One hundred six grams) complete in all respect including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slabwith 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (tewenty millimetre) nominal size foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (fourty millimetre) nominal size, inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size finished with a floating coat of neat cement having Inside size 90x80 cm (Ninty x eighty centimetre) and 45 cm (Forty five centimetre) deep including C.I. cover with frame (Light duty) 450x610 mm (Four hundred fifty x Six hundred ten millimetre) internal dimentions, total weight of cover and frame to be not less than 38 kg (Thirty eight kilogram)(weight of cover 23 kg (Twenty three kilogram) and weight of frame 15 kg (Fifteen kilogram)) With Sewer bricks conforming to IS : 4885 complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge:

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre) dia.

150 mm (one hundred fifty millimetre) dia.

Providing and fixing PVC single equal branch with oval access door, 110mm (one hundred ten millimetre) nominal size, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete icluding fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc.complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110mm (one hundred ten millimetre) dia .

150 mm (one hundred fifty millimetre) dia

Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90mm (one hundred ten into ninty millimetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing division plate for urinals 600mm x300mm (six hundred millimetre into three hundred millimetre) virterous china including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15 mm (Fifteen millimetre) dia CP brass bib tap with capstan head including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Suket Construction Co. Pvt. Ltd.