REPAIR TO WOODEN/ALUMINIUM JOINERY, SUNKEN TREATMENT AND CERTAIN MISC WORK AT MILITARY STN JAMNAGAR

Amount

Demolition of cement concrete (un-reinforced) in any position not otherwise specifically provided complete all as specified and directed by Engineer-In-Charge.

M&L for 40 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate mixed with liquid water proofing compound @ 3% of cement in bottom of sunken floors complete all as specified and directed by Engineer-In-Charge.

M&L Cleaning vertical and horizontal surfaces of sunken slab using wire brushing followed by sanding with emery paper for loose materials/dust and applying two coats of epoxy resin component (Dr. Fixit DAMPGUARD or equivalent) solution/mix using nylon brush pouring Base part in appropriate container followed by the Hardner part and mix thoroughly to attain homogeneous smooth paste and dilute the mixed compound with water in ratio 1 part Base: 1 part Hardner: 1 part water by slow addition and mix thoroughly until a brushable consistency is obtained, first coat will be allowed to dry for 6 to 8 hrs before application of second/final coat) incl curing treated surface for 24 hrs complete incl applying evenly a coat of blown bitumen @ 1.5kg/sqm over entire treated surfaces incl spout holesbefore filling lean concrete complete and all as specified as per manufacturer instruction.

M&L 15mm thick rendering in cement plaster 1:3 with WPC on bottom and side walls of sunken incl finished even and smooth w/o using extra cement complete all as specified and directed by Engineer-In-Charge.

M&L filling PCC type E-2 1:5:10 (40 mm graded stone aggr) as in sunken floor after applying appropriate treatment to side walls cmplete complete all as specified and directed by Engineer-In-Charge.

Supply only liquid waterproofing compound complete all as specified and directed by Engineer-In-Charge.

Taking down cement plaster on brick, stone or concrete surface including racking out joints hacking for key scrubbing down with water to receive plaster a, etc complete all as specified and directed by Engineer-In-Charge.

M & L for rendering 15mm thick plaster in CM (1:4) on fair faces of stone masonry/brick/concrete surfaces or surfaces other than fair faces of brick work, finished even and fair without using extra cement complete all as specified and directed by Engineer-In-Charge.

M & L for rendering 10mm thick plaster in CM (1:6) on surfaces of brick work/ stone masonry /concrete surface, finished even and fair without using extra cement complete.

M & L for Rendering 5mm thick plaster in CM 1: 4 to ceiling,finished even & smooth with using extra cement complete

Preparation of newly plastered surfaces of wall incl sweeping clean with brush to remove loose dust, sand, etc and applying two coats of heavy duty waterproofing coat (Dr Fixit Wounderproof-1 or equivalent) by mixing water @ 25-30% to make slurry coating and allow 4 to 6 hrs time for drying up of first coat before application of second coat in perpendicular direction of first coat and further left to dry for 4 hrs complete all as specified and directed as per manufacturer instructions.

M & L for preparation of new plastered surfaces of walls by applying chalk whiting, preparatory to distempering and evenly applying two coats of oil bound distemper (oil emulsion) on walls complete all as specified and directed by Engineer-In-Charge.

M & L for preparation of newly plastered or unplastered surfaces including cornices, pilasters etc and applying three coat of white wash on ceiling complete all as specified and directed by Engineer-In-Charge.

M&L Preparation of newly plastered surface and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engineer-In-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area exc 1.5 sqm but n.exc 4.0 sqm complete all as specified and directed by Engineer-In-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area n.exc 1.5 sqm complete all as specified and directed by Engineer-In-Charge.

Taking down shutters of any description exc 1.0 sqm and nexc 2.0 Sqm each complete all as specified and directed by Engineer-In-Charge.

Refixing in same opening shutters of any description exc 1 sqm but n exc 2 sqm complete all as specified and directed by Engineer-In-Charge.

S&F 2nd class hard wood in plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned joints including necessary tarrying and sanding complete all as specified and directed by Engineer-In-Charge.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed by Engineer-In-Charge.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel designed with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face incl particle board core complete all as specified and directed by Engineer-In-Charge.

S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (any number of Panel) with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both faces,. The size of rail and styles as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated. complete all as specified and directed by Engineer-In-Charge.

S&F 35 mm thick Flush shutters, solid core constuction, with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats complete all as specified and directed by Engineer-In-Charge.

S&F powder coated anodised Aluminium alloy sections door frame weight 2.863 Kg/Rm and 12mm Toughened glass shutter Jindal or equivalent duly fitted with neoprene beading, glazing clips, glass panes 12 mm nominal thickness aluminium alloy handles etc. complete all as specified and directed. Note : Rates include all joining,, locking arrangements, handle, hinges etc

S&F 35 mm thick 2nd class hardwood factory made glazed & skeleton door shutter open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed by Engineer-In-Charge.

S & F in repair stainless steel wire cloth 0.36mm dia of wire and avarage width of aperture 1.40mm and fixed with stainless steel wire staple in any type of window/door/ventilator complete all as specified and directed by Engineer-In-Charge.

S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and directed by Engineer-In-Charge.

S&F100mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed,tupe B1 complete all as specified and directed by Engineer-In-Charge.

S&F Extruded aluminium alloy handles 150mm long, fabricated type, anodised complete all as specified and directed by Engineer-In-Charge.

S&F Aluminium anodised barrel tower bolts, 150 mm long, of extruded section. complete all as specified and directed by Engineer-In-Charge.

M&L preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-In-Charge.

S&F coloured aluminium anodised sliding window of 3 track, frame of section 92mm X 32mm X 1.47 mm or appropriate equivalent section and shutters of section 18 mm X 44 mmX 1.35 mm or appropriate equivalent section ,aluminium sections weighting 0.55 Kg/m, fixed with 4.80/5mm thick tinted glass with rubber gasket, handles, locking arrangement and SS wire mesh,aluminium powder coated any colour (powder coating not less than 50 micron) incl making good jambs, cills etc including taking down old iron window complete all as specified and directed by the Engr-in-Charge. Note : rate shall include all glazing/SS wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc

S&F in powder coated aluminium fixed louvered ventilator, frame of section 63.5mm X 38.1mm X 1.01 mm or appropriate equivalent section with 4 mm thick figured/frosted sheet glass with rubber gasket,Aluminium wire mesh, handles, locking arrangement etc incl making good jambs, cills etc and including taking down old iron ventilator complete all as specified and directed by the Engr-in-Charge.

S & F in repair stainless steel wire cloth 0.36mm dia of wire and avarage width of aperture 1.40mm and fixed with stainless steel wire staple in any type of window/door/ventilator complete all as specified and directed by Engineer-In-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed by Engineer-In-Charge.

M & L Non skid coloured ceramic tiles 7-8mm thick area of each tiles exceeding .06 Sqm but not exceeding .11 Sqm, in floors etc. set and jointed in neat cement slurry mixed with water proofing liquid compound and pointed in white or coloured grouting chemical to match , over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-In-Charge.

M&L Glazed ceramic coloured designer tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match 0ver 10mm thick plaster in cement mortar (1:3) complete all as specified and directed by Engineer-In-Charge.

S&F Coloured Vitrified tiles 10 mm thick (square/rectangular) polished area of each tiles n exc 0.36 sqm in floors & skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match in light shade including 15 mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-In-Charge.

M&L 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms,wash basin counter and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, incl 20 mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-In-Charge.

Moulding to Granite(single or double) slab including rounding off edges for 20 mm thick slabs including grinding and polishing complete all as specified and directed by Engineer-In-Charge.

Taking down steel tubing and connection including cleaning for refixing or removal to store complete

(a) 20mm dia

(b) 25mm dia

S&F tube medium grade galvanised steel with all fittings & fixed complete to walls & ceiling or laid in floors.

(a) 20mm dia

(b) 25mm dia

S&F in repairs Vitreous china wash basin, white , flat back , size 550 x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engineer-In-Charge.

S/F in repairs vitreous china wash basin coloured oval type including waste type etc complete but excluding pillar taps complete all as specified and directed by Engineer-In-Charge.

S&F 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and directed by Engineer-In-Charge.

S&F in repairs Brass CP wall Mixer for mixing hot & Cold water screwed down for iron pipe/CPVC pipe and fixed.make and joint with adhesive , taflon tape complete all as specified and directed by Engineer-In-Charge.

S&F in repairs bib taps cast copper alloy chromium plated, fancy type, long body, concealed type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed 15mm bore complete all as specified and directed by Engineer-In-Charge.

S&F in repairs angle cock 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-In-Charge.

S&F in repairs Pillar taps 15 mm dia, cast copper alloy , with capstan heads, chromium plated , screwed down high pressure ,with long screwed shanks and fly-nuts , screwed for iron pipe and fixed complete all as specified and directed by Engineer-In-Charge.

S&F in repairs 100mm dia Overhead Shower alongwith 190mm long shower arm casted, fixed to 15mm bore pipe or union complete all as specified and directed by Engineer-In-Charge.

Supply and fix in repair 75 mm bore PVC (SWR) plain floor trap with CP grating complete all as specified and directed by the Engr-in-Charge complete all as specified and directed by Engineer-In-Charge.

S&F in repairs PVC(SWR) pipe 110 mm dia, conforming to IS-13592-1992 type 'B', single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-In-Charge.

S&F in repairs PVC(SWR) pipe 75 mm dia, conforming to IS-13592-1992 type 'B', single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-In-Charge.

S&F 110mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed by Engineer-In-Charge.

S&F in repairs PVC(SWR) bend any radius, 110 mm dia.provided with access door complete all as specified and directed by Engineer-In-Charge.

S&F in repairs PVC (SWR) junction double, (double T), equal or unequal provided wit access door complete all as specified and directed by Engineer-In-Charge.

S&F 500ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with 20mm ball/float valve including dismantling of old one complete all as specified.

S&F 1000ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with 20mm ball/float valve including dismantling of old one complete all as specified.

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, including CI 'P' or 'S' trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish with and includingand PVC flushing pipe, 32 mm dia complete all as specified and directed by Engineer-In-Charge.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe). complete all as specified and directed by Engineer-In-Charge.

S&F CP Health Faucet with 1.50mtr tube & Hook any description including flexible attachment as,specified and directed by Eng-in-charge

S&F In repairs SS Curtain Rod Decorative pattern as approved by Engr-in-Charge.

S&F in repairs SS Curtain Rod Bracket decorative type all as directed and approved complete all as specified and directed by Engineer-In-Charge.

S&F Waste fittings,32mm brass , chromium plated for glazed ware sinks , basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-In-Charge.

S&F in repairs 32 mm bore PVC waste pipe with fittings of approved make suitable for WHB, Urinals etc complete all as specified and directed by Engineer-In-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for window grills etc complete all as specified and directed by Engineer-In-Charge.

S & F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new steel surfaces exc 10 cm in width or girth and applying 2 coats synthetic enamel paint over a coat of red primer complete all as specified and directed by Engineer-In-Charge.

sanu enterprise (BID ID -3187344)

ABR Trading Co (BID ID -3193477)

badri glass and construction (BID ID -3187468)

M/S Badri Electicals (BID ID -3193569)