SPECIAL REPAIR TO HANGER BLDG NO P 97 AT RALAWAS UNDER GE BANAR IN ARMY AREA JODHPUR

Amount

Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) for turbo ventilator at above 10m height, all as specified & directed by Engineer-in-Charge.

S&F 600mm dia Turbo vent in roofs of hangers at above 10m ht. complete all as specified and directed by Engr-in-Charge.

Dismantling of Plain or corrugated steel sheeting, any gauge,thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised, corrugated mild steel 0.63mm thick sheeting with two corrugations side lap, in roofs, walls etc. With grade of zinc coating 275 L- type or J-type hook bolts at a height of 8 to 12 mtrs, complete all as specified and directed by Engr-in-Charge.

S&F 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip & straight flashings (length & girth as fixed) with grade of zinc coating 275 as specified & directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with hot dip galvanised self drilling fasteners with EPDM washers (one fastener on each crest) complete all as specified & directed by Engineer-in-Charge. Note:- Roof height above 10 mtr.

M&L for preparing new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer as specified & directed by Engineer-in-Charge.

S&F 2 mm thickness fibre glass reinforced translucent corrugated (Polycarbonate) sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and directed.

S&F for stainless steel spikes of 1.4mm dia along with 25mm wide rubber (protective pad) to fixed on desired location complete all as specified and directed by Engineer-in-charge.

Dismantling 1mm dia and 1"X1" apeture square or hexagonal multithread HDPE Coplymer bird proof netting ultra voilet resistant fixed with nylone rope with 4mm dia GI wire.

S&F 1mm dia and 1"X1" apeture square or hexagonal multithread HDPE Coplymer bird proof netting ultra voilet resistant fixed with nylone rope with 4mm dia GI wire.

Dismantling wrought iron or mild steel work of any description not otherwise provided for MS Flat with galvanised steel wire netting fixed with tinned tacks or wire staples all as specified and directed by Engineer in charge.

S&F Rolled mild steel sections as in framing for cladding, glazing & the like fixed with angle cleats & connecting plates, etc. Fe410-W (Gde-E-250) quality-A at a height of 8 to 12 mtr complete as specified & directed by Engineer-in-Charge.

S&F Wire netting aperture of size 20 mm galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples all are specified and directed by Engineer in charge.

M & L for applying two coat of synthetic enamel paint over a coat of Red oxide zinc on new Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint all are specified and directed by Engineer in charge.

Taking out old unserviceable glass of any description, from old wooden or metal frames, or stone, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc, including making good breakages in taking out and handling removing to store or stacking for reuse.

S&F for fibre sheet glass 4mm thick for window/ventilators area not exc 0.50 Sqm in each pane complete all specified.

M&L in repair forming 20mm thick expansion joint filled with performed HDME filler applying bond breaker tape on top of filler board for complete width of joint, provn of closed cell polyethylene back up rod 25mm dia, filled with polyethylene sealant (min depth of sealant above back up rod shall be 12mm) complying with BS-5212, priming the sides and applying masking tape on edged of joint to prevent accidental spillage of sealant and removing the masking tape after sealant applied, for thickness of concrete slab 200mm complete all as specified and directed by Engineer in Charge.

M&L in repair for forming contraction (dummy) joints 75mm deep x 10mm wide (using diamond cutter)filled with expand polyethylene form (armoour board) applying bond beaker tape on top of armour board for complete width of joint, provn of colsed cell polythylene back up rod 12mm dia sealed with 10mm (depth min above back up rod) polythylene sealant complete with BS-5212, priming sides, masking tape on edges of joint to prevent accidental spillage of sealant on top surfaces and to give a neat finish to the sealant and removing the masking tape after sealant application complete all as specified and as directed.

M&L in repair forming construction joints 30mm deep and 10mm wide, (using diamond cutter) and sealed with polyethylene sealant complying with BS-5212 and priming the sides, provn of closed cell polyethelene line back up rod 12mm dia and applying masking tape on edges of joint to prevent accidental spillage of sealant on top surfaces and to give a neat finish to the sealant applied complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n exc 4 sqm each complete all as specified and diected by Engineer-in-charge.

.--Ditto-- as per item no. 21 here-in- above but not exc 1.5 sqm each complete all as specified and diected by Engineer-in-charge.

S&F, Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed by Engineer-in-charge..

S&F, Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips rubber neiprene packing, handles 2 nos in each door, hinges, anodised aluminium snap beading screws etc. complete all specified & directed by Engineer-in-charge.

S&F, Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

S & F aluminium alloy wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples or clip in aluminium frame complete.

Supply & Fix sheet glass 5.5mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed by Engineer-in-charge.

S&F for door closer(aluminium extruded body) hydreulically regulated, ,designation No 1 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg & fixed, complete all as directed.

S&F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor of size 150mm complete all as specified.

S&F mild steel 4 Lever mortice lock, vertical type of size 100mm all as directed.

Material and labour for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) drawn into and including PVC casing caping (heavy duty) and accessories fixed on walls/floors/ceilings etc alongwith continuous earth wire 1.5 Sqmm PVC insulated and unsheathed single core FRLS cable (Earth - Green) 1100 volts grade with stranded copper conductor and connected to common earth dolly, with and including 1.6mm thick cadmium plated sunk MS pressed steel terminal boxes with 3mm thick plastic laminated sheet cover fixed with brass screw etc complete all as specified for the following :-

(a) One light point controlled by one switch.

(b) One fan/exhaust fan point controlled by one switch.

(c) One bell/buzzar point controlled by one bell push independent.

(d) One switch socket outlet point 5 Amps on independent board

(e) One switch socket outlet point 5 Amp on same board

Material and labour for surface point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black, Earth - Green) drawn into and including PVC casing & caping with all fittings and accessories fixed properly on wall or ceiling including PVC terminal boxes for mounting switches socket for 3 pin 15 Amp independent board all as specified and as directed by Engr-in-Charge.

Supply and fixing switch piano flush button single pole one way 5 amp complete.

Supply and fixing ceiling rose 63 x 25 mm three terminals complete.

Supply and fixing socket outlet 2 in 1, 3 pin, 5 amp, flush type complete.

Supply and fixing socket outlet 2 in 1, 5 pin 5 & 15 amp flush type complete.

Supply and fixing switch piano flush button single pole one way 16 amp complete.

Supply and fixing bell/buzzer ding dong AC 230 Volts single pole

Supply and fixing bell push flush type complete.

Supply and fixing stepped type electronic fan regulator, flush type

M&L for submain wiring along with earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable 6 Sqmm (Phase- Red, Neutral-Black, earth-Green) drawn into and including rigid non metallic PVC conduit not less 25mm dia, medium gade, ISI marked ivory colour along with accessories fixed with clamp properly on wall or ceiling as per specified as directed by Engr-in-Charge.

Supply and fixing in repair powder coated, CRCA steel sheet MCB distribution board double door, single pole and neutral 8 way 240 Volt fitted with busbar, earth bar, DIN rail, neutral link and incoming contact.

Supply and fixing in repair powder coated, sheet metal enclosures Verticle TPN distribution board, double door and neutral, 4 way 415 volts for MCCB incomer with & including MCB outgoing 40 Amps TPN-4 Nos fitted with insulated vertical phase bus bar/neutral bar with shrouded earth bar cement spill protector interconnecting wire set cable tiesblanking plates and circuit indentificaiton etc all as per IS-8623 1K-09

Supply and fixing in repair MCB SPN 32 Amps 240 Volts

Supply and fixing in repair MCCB TPN 125 Amps 415 Volts, 16 kA adustable overload setting and fixed magnetic setting

Supply and fixing in repair MCB SP 6-32 Amps 230Volts

S&F in repair metal clad plug and socket with box 20 Amp with MCB complete fixed properly on wall surface with the provisioning of suitable sizes of bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 4 Sqmm as per specification as per directed.

Material and labour in repair for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

All as per Sr Item No 53.00 here-in-above but earth lead of GI strip 32 X 6 mm and protection pipe 40 mm.

Material and labour for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black, Earth - Green) drawn above surface and roof including with stove enamelled steel conduit medium grade (flame proof) not less than 20 mm dia ISI marked black colour with all conduit fittings / fixing accessories of the following :-

(a) One light/fan point controlled by one switch.

Ditto all as per item No. 55 herein before but with 4 sqmm PVC insulated multistrand FRLSH single core copper conductor cable for one 15 Amp flame proof switch socket outlet and using 4 sqmm PVC insulated multistrand FRLSH single core copper conductor cable multistranded as earth wire complete all as specified and directed.

Supply and fix in repair switch single pole, 250V flame proof, rotary type with termination box in LM6 complete all as directed by EIC.

Supply and fixin repair flame proof switch socket & plug combined in LM6, 16A, 250V (2P+Earth) complete all as directed by EIC.

M&L for two run of single core 6 Sqmm PVC insulated cables (FRLS) with stranded copper conductor 1100V for sub main wiring (concealed) and drawing in to suitable size of stove enamelled steel conduit (ISI marked) with all accessories including 6sqmm size PVC insulated stranded copper conductor cable earth continuity conductor complete all as specified and directed. Note : Two run of sub main, one run of earth wire and one run of MS Conduit shall be treated as one unit i.e one RM

Supply & fixing in repair surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including lamp LED 1x20/1x22 W (4 feet) fixed properly on wall surface and connecting complete from ceiling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit all as directed.

S&F in repair recess mounting (2'x2') 36W LED light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for fixed properly on ceiling and connecting complete to fitting by three core copper conductor cable of overall sheathed size 1.5 sqmm which shall be passed through PVC flexible conduit all as directed by Engr-in-Charge.

S&F in repair building security light LED fitting with pressure die cast housing, epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable lamp LED 45W, fixed/connect properly complete all as directed.

M&L in repair for metallic body exhaust fan 230mm sweep, single phase 240 volt AC, 900 RPM four blade with louver shutter complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5sqmm 3core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr all as directed by Engr-in-Charge.

Supply and fix in repair LED light fitting, 1x20W LED, flameproof type FLP-WP, made of aluminium alloy LM6 and all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Supply and fix in repair flame proof exhaust fan 305mm sweep of single phase with all accessories complete all as directed by EIC

Supply and fix in repair flame proof fan regulator rotary type complete all as directed by EIC.

Supply and fix in repair flame proof junction box with plain cover, entry size 3/4 ET, 3 way complete all as directed by EIC.

Supply and fix in repair flame proof distribution board SPN 8 way double door with 200 amps, rated busbar complete all as directed by Engr-in-Charge

Supply, fixing and installation in repair heavy duty wall mounted air circulators oscillating type fan 600mm sweep 1440 RPM single phase 250W vertical angle adjustment from 22 to 45 degree push button three speed control by regulator (including in this price) to connect by using cable PVC insulated copper stranded conductor of size 2.5sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit all as reqd and as directed by Engr-in-Charge.

Taking down carefully aluminium/copper point wiring of any type/size for light, fan, socket or power complete including making good the disturbed surfaces of wall/ floor etc complete all as specified and directed.

Taking down existing sub main wiring of any type/size complete from wall and making good the disturbed surface.

Taking down existing MCB DBs of any type/size complete from wall and making good the disturbed surface.

Supply and fix in repair earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4mm dia galvanised iron wire all as directed.

S&F in repair bracket made out of 40 mm bore GI tubing light grade 1.50 mtr long bend to required shape as in bracket for building secuirity fixed with two pair of MS flat iron clamp not less than 30 mm width and 4mm thick of appropriate length in required shape suitable to 40 mm GI pipe (as per site requirement) with bolts, nuts, and washers and other petty items required for fixing including painting with two coats of syntheitic enamel paint over a coat of redoxide primer complete all as specified and directed by Engr-in-charge.

M/S KAUTILYA GARG

JAGDISH PRASAD & CO

RISING ELECTRICALS