Construction of Additional Accommodation PWD Rest House at Bagsaid in Tehsil Thunag Distt Mandi SH C/o Building portion site development WS SI and harvesting system

Amount

Cutting in earth work all kinds of soils and disposal of excavated earth upto a lead of any metres such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including levellingup with cement concrete 1:6:12 (1 cement : 6 Sand : 12 Graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1cement:6 sand) in breast walls and retaining walls.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm nominal size) mechanical mixed and curing complete excluding cost of centring and shuttering in:oundation and plinth: as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:- Foundation, footing basis of columns etc. and mass concrete .

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness up to all floor level

Beams, cantilever, girders and lintels sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels in any depth in all height from floorup to all floor level

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan up to all floor level

Stair cases with sloping or stepped soffits excluding landing up to all floor level

Edges of slabs and breaks in floors and walls in any width. up to all floor level

Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like

Providing and laying reinforced cement concrete design mix M-25 (Design mix) grade mechanically mixed and vibrated and curing excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge pior to the casting . The theoritical consumption of cement fot the item shall be worked out as per approved design mix as per I.S code including carriage of materials with in all leads, lifts and other incidentals . Foundation, footing basis of columns etc. and the like and mass concrete .

Suspended floors, roofs ,landings and shelves and their support, balconies, beams, girders, breasumers and cantilevers up to all floor level

Columns, pillars posts and struts up to all floor level

Stair cases (except spiral stair cases) excluding landing but including preparing of the top surface and finishing of nosing up to all floor level

Providing and laying reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S code in string courses, copings, bed plates, anchor blocks, plain windows sills and the likes up to floor all floor level including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S code in string courses, copings, bed plates, anchor blocks, plain windows sills and the likes up to floor all floor level including carriage of materials with in all leads, lifts and other incidentals ii)Walls (any thickness but not less than 0.10 m (Zero point one zero) metre thickness) including attached pilasters , buttersses,plinth and string courses etc. from top of foundation upto floor all level

i)Suspended floors , roofs, landings and shelves and their support , balconies, beams, girders,bressumers and cantilever upto floor any level.

Stone soling/boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Back filling behind abutment wing wall and retainling wall complete as per drawing & technical specification clause 1204.3.8. including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing weep hole in brick masonry/ stone masonry / plain reinforced concrete abutment, wing wall, return wall with 100mm dia.(one hundred millimetre diametre) PVC pipe extending through the full width of the structures with slope of 1V:20H (one vertical isto twenty horizontal) towards drawing face complete as per drawing and technical specifications clauses 614,709,1204.3.7 including carriage of material and other incidentials as per the direction of the Engineer-in Charge .

Providing RCC Smooth finishing of the exposed surface with cement morter 1:3 (one cement : three sand) including carriage of material and other incidentials as per the direction of the Engineer-in Charge .

Providing and laying 20 cm. (twenty centimetre) thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6 (1 cement :6 sand) and concrete backing with cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stoneaggregate 20 mm (twenty millimetre) nominal size on inner face of walls including centring,shuttering and propping complete up to all floor level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . upto Floor any Level

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick) in super structure above plinth level up to floor level as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other ncidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:5 (one cement : five sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing Second class deodar wood work in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

P/F 12 mm (twelve millimetre) thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm (fourty millimetre) thick frame as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing 40x3 mm(Forty x three millimetre ) flat iron hold fast 40cm. (Forty centimetre ) long including fixing to frame with 10mm (Ten millimetre ) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm.(Thirty x ten x fifteen centimetre ) 1:3:6 ( One cement : three sand: six graded /crushed stone aggregate 20mm(Twenty millimetre ) nominal size within all leads and lift including carriage of material in all respect and as per direction of Engineer-in-charge.

Providing and fixing 40 mm (Forty millimetre) thick 2nd class deodar wood panelled glazed or panelled glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws etc. complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 40 mm (forty millimetre) thick 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing double glazing(doubleglass ) fixed in wooden window ventilator shutters and partition rtc with wooden corner or wooden bead in teak wood bead etc. of specifified size with nails mitred and jointing complete and glazing with glass panes of 4 mm(four millimetre) thick(weight not less than 10.00 kg/sqm. as per the direction of Engineer-in-chargeincluding carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 12mm(twelve millimetre) thick 150mm(one hundred fifty millimetre) wide pelmet with 25 mm(twenty millimetre) diametre wooden curtain rods and brackets including fixing 25x3mm M.S. flat at 10 cm. Long and plugs etc. complete as per the direction of Engineer-in-chargeincluding carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing brass curtain rail with rollers stop ends and bracks in pelments instead of wooden curtain rod 25 mm (twenty five millimetre)dia and brackets of first deodar wood acctual length) of rails of be measured.as per the direction of Engineer-in-chargeincluding carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing Plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 75 mm x60mm (seventy five millimetre x sixty millimetre) moulded hand rail in straight length complete in second class teak wood.as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing MS sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 300x16mm (three hundred x sixteen millimetre)

250x16mm (two hundred fifty millimetre x sixteen millimetre)

Providing and fixing anodized MS tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250x10mm (Two hundred fifty x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

Providing and fixing MS handles with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred twenty five millimeter)

100 mm (One hundred millimeter)

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 150 mm (one hundred fifty)

Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. double acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 90 mm (ninety millimeter) oxidized MS heaps and stapples (safety type) with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 50 mm (fifty millimeter) chremium plated brass cup board or ward robe knob with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm ( ten millimetre) bright finished bress ball catcher with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10mm (ten millimetre) digital ceramic tile of size 300 x 600 mm (three hundred into six hundred millimetre)in skirting risers of steps and dados on 8 mm (eight millimetre) thick cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and laying spartic ceremic tiles 5.5mm ( Five point five millimetre ) thick in flooring 300 x300mm (Three hundred x three hundred millimetre ) treads of steps laid on a bed of 12mm (Twelve millimetre) thick cement mortar 1:3(One cement: three sand) finished with flush pointing in white cement within all leads and lift including carriage of material in all respect and as per direction of Engineer-in-charge.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10 mm(ten millimetre) thick WI-Paraquit or action tesa clip in prelaminated wooden flooring (H.D.F) with poly sheet & thermocoal sheet with door profile and side moulding locks with all fittings ,etc. complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. Up to Floor any level.

Providing and laying Flaming granite stone in single piece flooring 20 mm (twenty millimetre) (average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

25 mm (Twenty Five millimetre) thick Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. Up to Floor any level.

Providing wood work in frames of false celling partitions etc. sawn and put up in position in second class deodar wood as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 25mm (twenty five millimetre) thick wooden plank first class indian teak wood. ceiling with tongued and grooved jointing and wood screws (frame work and cover fillets to be measured and paid for separately) as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing angle iron cupboard frames frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge including carriage of materials with in all leads, lifts and other incidentals.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreignmatter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including carriage of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white as per the direction of Engineer-in-Charge including carriage of materials within all leads,lifts and other incidentals.

Providing and fixing 19mm (nineteen millimetre) thick terramite resistant water proof Commercial Board box including shelves and shutters the back side of cupboard/ cabinet of 8mm (eight millimetre) thick ply and cut portions of shelves shall be finished with 6mm (six millimetre) hard board edging. The cut portion of shutters from all the sides shall be finished with 12mm (twelve millimetre) hard wood edging the shutters from out side shall be finished with 1mm (one millimetre) thick laminating of approved shade including piano hinges and mgnetic catcher with all ascesories as per deatil architectural drawing No. 195/1 to 199/1 etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters with 6mm (six millimetre) thick hard wood edging for cup boards including fixing with nickel plated piano hinges with screws etc. complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stopingready mixed paint other thanwhite as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 12mm (twelve millimeter) thick Glass Reinforced concrete cladding of approved shape and texture of unistone or its equivalent made from portland cement alkally resistance glass fibres, UV resistant synthetic inoraganic pigment combined with the range of chemical additives on exterior surface side as on faces of Arch masonry walls etc. 12mm. thick cement plaster 1:3(1cement:3sand) and jointed with cement slurry including scaffolding etc complete in all respect as per specification and the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing valley 90 cm (ninety centimetre overall 0.60mm (Zero six zero milimetre)thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat og regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with screws, preprinted iron J and L hooks,bplts & nuts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals

Providing and fixing M.S. BP Sheet 1.66 mm (One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in: In beams joists,channels angles,tees,flats with connectiong plates or angle cleats as main and cross beams hip and jack rafters purlins connected to common raffers and the like.including carriage of materials with in all leads, lifts and other incidentals.

In gratings framed guard bars laddeds railing brackets and similar works including carriage of materials with in all leads, lifts and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth Priming coat with distemper primer as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete s per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing plinth protection 50mm (Fifty millimetre) thick in cement concrete 1:3:6 (one Cement : three sand : six Graded stone aggregated 20mm (Twenty millimetre) nominal size) mechanically mix finishing surface of concrete smooth as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing plain lining with tongued and groved jointing and screws (frame work and cover fillets to be measured and paid for separately with 2nd class indian teak wood 12 mm (Twelve millimetre) Thick as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Prelaminated board bwp phenol bonded exterior/interion grade both sides 12 mm (Twelve millimetre) thick as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Varnishing two coats (excluding priming coat)on new wood and wood based surfaces,under coating,with flatting varnish and finishing coat with varnish to give an even surface including cleaning the surfaces of all dirt,dust and sand papering so as to produce a smooth,dry and matt surface including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm(Four point five kilogram per square metre) including filling the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals i)20 mm (twenty millimetre) nominal bore

Providing and fixing PVC water storage tank of ISI:12701 marked,G.I.inlet and outlet connection,15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level:-2000 litres (Two thousand literes) capacity.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 38 kg (thirty eight kilogram) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing plythelineo-aluminiumo-polythelene(PE-AL-PE) composite pressure pipe U.V.stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one meter spacing,cutting,fixing and making good the wall etc.but excluding the cost of fittings(internal work) pipes exposed on wall.internal worko-exposed on wall. (KITEC make) other incidentals 1620 (20 mm ( OD pipe) (twenty millimetre)

1216(16mm O.D.Pipe.) (sixteen millimetre)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors,couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. (KITEC make)as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. Reducing tees 1620 x all branches

Equal tees i)1216

Female branch TEE i)1216x1216x15mm (One thousand two hundred sixteen millimetre into One thousand two hundred sixteen millimetre into fifteen millimetre) thread.

Female elbows i)1216x15mm (One thousand two hundred sixteen millimetre into fifteen millimetre) thread.

Female thread connector i) 1216x15mm (One thousand two hundred sixteen millimetre into fifteen millimetre) thread.

couplers i) 1216

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc complete. as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 nominal (Seventy five millimetre) size.

110mm (Seventy five millimetre) nominal size.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick (Three millimetre) bolts and nuts complete icluding fixing with approved adhesives etc. 110mm (one hundred ten millimetre) nominal size.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing PVC single equal branch plain, ISI marked including fixing with approved adhesives etc.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (Seventy five millimetre) dia

110 mm (one hundred ten millimetre) dia

Providing and fixing PVC collar, ISI marked including fixing with approved adhesives etc.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (Seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC plain bend, ISI marked including fixing with approved adhesives etc. 75 mm (Seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC clamp, ISI marked of approved design with steel screws and rawal plugs etc. Complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (Seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC floor trap ISI marked of self cleansing design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. 110 mm x 75 mm ((one hundred millimetre into seventy five hundred millimetre) size. as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down,water closet Orissa Pattern No. 2071 squatting pan (Indian type W.C pan) size 580mmx440 mm (five hundred eighty into four hundred fourty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China washdown, water closet (European type. W.C. pan) EWC No. CNS-WHT-WH10P of size 390x 365x540 of Jaguar with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately)as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing two piece WC seat for coupled WC ARS-WHT-39751S with PP soft closet seat cover hinges, fixing accessories set and accessories set of size 375x650x800 mm (Three hundred seventy five into six hundred fifty into eight hundred millimetre) including cistren ARS-WHT-39201 complete with jet spray etc and 'S' trap of size 250mm of Jaguar complete as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT colored / white high density polyethylene / poly propylene 10 (Ten) litres capacity (Full flush) European standred control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15 mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40 mm (fourty millimetre) dia CP flush bend including cutting hole in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for seperatly) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing plastic seat (Solid type) and cover of Jaguar for wash down water closet with C.P. Brass hinges and rubber buffers ( white plastic seat and cover) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing Memories self rimming lovatory wash basin of size 579 x459 x 220 No K-2241IN-1-0 with pedestal of Kohler or its equivalent with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing under counter wash basin of size 480 x 370x 200 of Rectangular shape No SNS-WHT-701 of Jaguar or its equivalent with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash basin No. CNS-WHT-807 of size 760x500x210mm ( Seven hundred sixty into five hundred into two hundred ten millimetre ) of Jaguar or its equivalent with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China pedestal of jaquar/ Kohler for wash basin complete recessed at the back for the reception of pipes and fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing CP brass toilet paper holder including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS)

Providing and fixing C.P Brass waste for wash basin or sink :- (a)32mm (Thirty two millimetre) dia as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing MI union for wash basin or sink :- (a) 32mm (Thirty two millimetre) dia as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing vitreous china blow pattern urinal of jaquar/kohler i/c connection the with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) i/c carriage of materials in all leads and lifts and as per the direction of Engineer-in-Charge. Flat back type of size 430x260x350mm (Jaquar or ESS-ESS)

Providing and fixing division plate for urinals 600mm x300mm (Six hundred into Three hundred millimetre) virterous china including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 600mm x 450mm (Six hundred into Four hundred fifty millimetre) ( beveled edge mirror of superior glass mounted on 6mm (Six millimetre) thick A.C sheet or ply wood sheet and fixed to wooden plugs with C.P brass screws and washers . as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P brass towel rail complete C.P brass brackets fixed to wooden plugs with C.P brass 600mmx20mm. (Six hundred into twenty millimetre)Thick (Jaquar or ESS-ESS) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 600 x 120 mm (Six hundred into one hundred twenty millimetre) Glass shelf with CP Brass bracket and gaured rail complete fixxed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. brass flush pipe/spreaders for urinal with fittings such as unions, clamps etc. (all C.P.) including cutting holes and making good the same including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. 15mm nominal bore

Providing and fixing 32mm lead waste pipe for wash basin or sink including check nut including carriage of material with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing chromium plated brass soap dish with C.P brass brackets fixed to wooden cleats with C.P brass screws . (Jaquar or ESS-ESS)as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia CP brass bib tap with capstan head Jaquaror ESS-ESS as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia CP brass pillar tap with capstan head :- 15mm dia (Jaquar or ESS-ESS) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia CP brass angle valve with out nuts and pipe as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) bore P.V.C connection pipe with brass unions . 300/450mm length as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing PTMT jet spray of approved quality and colour with 1metre tube.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT grating round of approved quality and colour 100 mm (one Hundred millimetre) nominal dia.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Constructing manhole with R.C.C top slab in 1:2:4 (1 cement :2 sand :4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 (I cement :4 sand : 8 Graded stone aggregate 40mm nominal size ) inside plastering 15 mm thick with cement mortar 1:3(1 cement : 3 sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement :2 sand :4 graded stone aggregate 20mm nominal size)finished smooth complete including curing and testing :- (i)inside size 800mmx800mm (Eight hundred millimetre into Eight hundred millimetre) and 500 mm (Fivet hundred millimetre ) deep including C.I. cover with frame( light duty single (seal ) pattern I) 450mmx610mm (Four hundred fifty millimetre into Six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. A)with 200 mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1cement :3sand ). as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing brass stop cock 15 mm dia (Fifteen millimetre)as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Shower head arm casted 19 mm ( Ninteen millimetre) long body round shape SHA -CHR-477 for wall mounted shower with flange of Jaguar complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing Grab Bar of Jaguar WAC-WHT-BR0600 692 mm (Six hundred ninety two millimetre) satinless 40mm ( Fourty millimetre) dia steel pipe at 78 m (Seventy Eight mtr.) height with MS plate as the position of seat as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

KDN Infrastructure Pvt. Ltd.