Loading…
Loading…
Tender Value
₹10.0 Cr
EMD Value
₹10 L
Closing Date
25 Jun 2026, 6:00 pm
The Managing Director
Development work of Ecological Tourism Site at Wilson Hill, Dist.Valsad, Gujarat
310960
2026
Open
Civil - All
Gandhinagar
2 documents required · 2 mandatory
₹12,000
Tourism Corporation of Gujarat Limited
₹10 L
3 Jun 2026
3 Jun 2026
3 Jun 2026
25 Jun 2026
3 Jun 2026
Sr.No Description of items. Unit Total Qty Total Rate Total Amount.
Excavation for foundation upto 1.5 m depth including sorting out and
2 stacking of useful materials and disposing off the excavated stuff upto 50 Cum 2,245.79 264.82
Meter lead.(A) Soft rock not requiring Blasting
Excavation for foundaation for depth from 1.5 m to 3.0 m including sorting
3 out and stacking of useful materials and disposing off the excavated stuff Cum 619.47 287.48
upto 50 Meter lead.(A) Soft rock not requiring Blasting
Filling Available Excavated Earth (Excluding Rock) In Trenches. Plinth, Sides
4 Of Foundations Etc. In Layers Not Exceeding 20 Cm. In Depth Consolidating Cum 3,942.12 130.39
Each Disposited Layer By Ramming And Watering
Earthwork for embankment including breaking clods, dressing with all lead
and lift and including watering rolling and consolidation of subgrade in
5 layers at O.M.C. to required dry density including filling the depression Cum 30,365.64 169.44
which occur during the process using power roller 8T to 10T.(E) From
Borrow area within 3.0KM. lead
Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6-
6 crushed stone aggregates 20 mm nominal size) and curing complete Cum 1,181.28 4,030.98
including cost of formwork in (A) Wall Caps / Coping
Providing and laying controlled cement concrete M.250 and curing complete
including the cost of formwork and excluding cost of reinforcement for
reinforced concrete work in (A) Foundations, footings, Base of columns and
Mass concrete. (upto 10 ton)
Providing & laying Controlled cement concrete for plinth beam(tie beam),
Ground beam with M-250 cement concrete including finishing smooth with
curing etc. complete including the cost of formwork but excluding the cost
of reinforcement for any cross sectional area of beam.
Providing & laying Controlled cement concrete M-250 and finishing smooth
with curing etc. complete including the cost of formwork but excluding the
cost of reinforcement for RCC column work having any cross sectional area
.For Column Up to Plinth & all floors.
Providing & laying Controlled cement concrete M-250 and finishing smooth
with curing etc. complete including the cost of formwork but excluding the
cost of reinforcement for R.C.C. work in slabs, Sunk Slab & Beam having
thickness more than 10 cm and upto 20 cm thickness.For all floors
Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending,
binding and placing in position complete upto floor two level
Structural steel work ( Confirming to IS 4923-1997) riveted, bolted or welded
in builtup for all type sections, in framed work, including cutting, hoisting,
fixing in position and applying a priming coat of approved steel primer all
complete as per the structural designs and directions of Engineer in charge
Brick work using common burnt clay building bricks having crushing strength
13 not less than 35 kg./Sq.Cm. in foundation, plinth and superstructure in cum 635.73 4,388.47
Cement Mortar 1:5. (1 Cement : 5 -fine sand)(A) Modular
Providing 10mm thick cement plaster in single coat on brick/concrete walls
14 for interior plastering upto floor two level and finished even and smooth in Sqmt 1,787.50 116.13
(ii) Cement mortar 1:4 (1-cement :4-sand)
Providing 15mm thick cement plaster in single coat on Rough (Similar)side of
15 single or half brick walls for interior plastering upto floor two level and Sqmt 4,611.77 171.80
finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)
Providing 20 mm thick double coat mala cement plaster on interior brick
/Exterior/ concrete work for plastering comprising of base coat of 12 mm
16 thick cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough Sqmt 3,654.72 272.48
finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse
sand) finished with trovel including scaffolding curing etc. complete.
Providing and filling rubbles including hand packing and filling interstices
with quarry spalls behind abutments and between returns as directed.
Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in flooring
treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3
(1-cement : 3-coarse sand )
finishing with flush pointing in white cement.
Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in skrting
19 risers of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3- Sqmt 418.46 1,141.45
coarse sand) and jointed with white cement slurry
Providing and laying white glazed tiles 6mm thick in flooring treads of steps
and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-
coarse sand ) finishing with flush pointing in white cement.
Providing and laying white glazed tiles 6mm thick in skrtingrisers of steps
and dedo on 10mm thick cement plaster 1:3(1-cement : 3-coarse sand) and
jointed with white cement slurry (Tile Size 300x600)
Providing & laying Sandwich platform of maximum 700mm width a)
Sandwich type platform of top stone as 18 mm thick Granite of approved
shade and sample and bottom stone as 25 mm thick single side polished
kota stone with 25 mm thick screed of cement mortar 1:4 in between two
stones. The stone shall be fixed by chasing in to the wall surface and
providing necessary MS supports of 50x50x6mm Angle or "T" (hot dip
galvanised) and embedded in between the two stones etc as per the drawing
/ specification and / or as instructed of EIC complete and b) 75 mm raised
platform (Otli) at floor level with polished kota laid on 50mm screed of
(1:2:4) and skirting of kota stone as per design and approved sample. The
rate includes rounding, champhering and mirror polishing of edges, facias of
granite, MS supports, all material labour and wastage, as per drawing,
including necessary bonding adhesive (if required) of Araldite or equivalent.
Rate shall be also inclusive of making holes & cutouts for SS sink, Oval wash
basin, Piller tap / Bib tap etc. as directed by engineer in charge. (Only
finished single side granite work shall be measured & paid for).
Providing and fixing 600mm x 450mm bevelled edge mirrror of superior
glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to
wooden pluge with C.P.
brass screws and washers.
Providing and fixing Urinal of approved quality including connection with
24 trap and with integral longitudinal flush pipe.(A) Squating plate pattern Each 8.00 1,550.99
white earthenware 550mm x 300mm.
Providing wood work in frames of Doors, windows cleare story windows and
25 othersimilar works wrought, framede and fixed in position. (A) Indian Teak 10CU.DM. 257.81 608.06
Providing and fixing 35 mm thick shutters for Doors, windows and clearstory
26 windows including blackenamelled M.S. butt hinges with necessary screws. Sqm 114.61 3,941.37
(A) Indian teak wood. (i) Fully Panelled.
(ii) Providing and fixing glazed louvered glass windows and ventilators with
27 teak wood frame 10cm. x 7cm. size including 3 coats of oil painting to wood Sqm 5.54 4,375.79
work etc.complete. with wooden louvers plank 12mm thick
Providing and fixing 30mm thick FACTORY MADE SOLID SINGLE SIDE PRELAM
PANEL PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of
gauge thckness and size of 19mm x 19mm for stiles, and 15mm x 15mm for
top and bottom rails. The M.s. frame shall have coat of steel primers of
approved makde and manufacture. The M.S. frame shall be covered with
5mm thick heat moulded single side prelim PVC ‘C’ channel of size 30 x
50mm to form stiles and 5mm thick and 75mm wide single side prelim PVC
sheets shallbe for the top, bttom and lock rails. Paneling of 5mm thick one
side prelim sheet to be fitted in the M.S. frame and sealed to the front
28 (Prelam side) stiles and rails (which should have a 5mm 45 degree bent Sqm 29.10 2,023.03
portion as beading) and attached to the back (white/lvory) stiles and rails
(which should have a 10mm 90 degree bent portion as beading) using 2 nos.
15mm wide x 5mm thick PVC sheet beading inside the 9 degree bent
beading. All stiles, rails and beading to be joined to the panel using solvent
cement.An additional 5mm thick PVC strip of 20mm width is to be struck on
the interior side of the ‘C’ channel using PvC solvent adhesive and 10mm
thick (5mm x 20) thick 20mm width cross PVC sheet to be fitted as gap insert
for top and bottom rails, etc. complete as per direction of Engineer in
charge, manufacture’s specification and drawing.
Fixing Metallic tower bolts of sizes with necessary screws etc. complete
(Tower bolts and screws to be paid under separate items)
Fixing metallic or plastic door handles of sizes with necessary screws etc.
complete (Door handles and screws to be paid under separate items)
Fixing metallic door latches of sizes with necessary screws etc. complete
(Door latches and screws to be paid under separate items)
Fixing metallic floor door stoppers of sizes with rubber cushion screws etc.
32 to suit shutter thickeness complete (Floor door stopper with rubber cushion Each 140.00 4.30
and screws to be paid under separate items)
Fixing metallic door handles or knobs for mortice locks with necessary
33 screws etc. complete (Door handles /knobs and screws to be paid Each 140.00 3.67
Providing and fixing post and pipe railing as per detailed drawing including
34 coats of painting to steel works Rmt 52.80 1,205.11
Applying two coats of putty & two coats of primer of approved brand and
manufacture on new wall surface to give an even shade including thoroughly
brushing the surface free from mortar dropping and other foreign matter
and sand papered smooth.
Distempeing (Two coats) with oil bound distemper of approved brand and
manufacture and of required shade on wall surfaces to give an even shade,
over and including a priming coat with distemper primer of approved brand
and manufacture after thoroughly brushing the surface free from mortar
dropping and other foreign matter and also including preparing the surface
even and sand papered smooth.
Finishing wall with weather proof exterior emulsion paint on wall surface
(two coats) to give an required shape even shade after thoroughly brushing
the surface to remove all dirt, and remains of loose powdered materials.etc
Providing and fixing PVC Printed pain colour false ceiling with grid type with
alluminium frame consisting of 600mm x 600mm 3mm thick plain PVC sheet
used as panel insert in a frame work made using anodized alluminium T
section of size 1 x 1 (235 x 25mm, 19 gauge or 1 mm thick) in square pattern
of grid sizes of 2 x 2 (600 x 600mm) The alluminium frame work is supported
from the cceiling with the help of G.I. hook and G.I. wire/6mm M.S. rods of
required sizes to maintain proper level etc. The aluminium frame work is
supported on side wall with the use of alluminium L section of size 1 x 1 (25 x
25mm) angles etc. complete as per direction of Engineer in charge.
Manufactures specification and drawing.
Providing and fixing eco-friendly light weight calcium silicate false ceiling
tiles having Tegular edge & 15 mm Thick Densified edges on the Tile
Periphery for Extra Strength The Light weight calcium silicate ceiling tiles
shall have, light reflection 85% non-combustible as per B.S. 476 part IV,
100% humidity resistance and also having thermal conductivity0.043° w/m
KC.for the best thermal Insulation . The Light weight calcium Silicate tile shall
be of approved texture Fine fissured/ Spintone/Cosmos having NRC value of
0.5 & Globe having NRC value of 0.75 NRC or equivalent of size 595 X
mm to be laid on true horizontal level suspended inter locking metal grid of
hot dipped galvanized steel sections (galvanizing @120 grams per sqm
including both side) consisting of main ‘T’ runner suitably spaced at joints to
get required length and size of 24X38mm made from 0.30 mm thick
(minimum sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm
made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced
between main ‘T’ at 600mm centre to centre to form agrid of 1200X600mm
and secondary cross ’T’ of length 600mm and size 24x28mm made of
mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm
panel to form grid of size 600X600mm resting on periphery walls/partitions
on a perimeter wall angle pre-coated steel of size (24X24X3000mm made of
0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre
to centre with 25mm long dry wall screws @ 230mm interval and laying
15mm thick Densified edges
Providing laying (to level or slopes) and jointing reinforcedconcrete Light
duty non-pressure pipes I.S. class NP2 of the following internal diameter
with collars and butt ends prepared for collar joints including testing of
joints complete.(H) 900mm
Landscaping work
Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm
thickness of existing ground prepared with proper level and ramming with
41 tools wooden (Dhurmos) and than rolling the surface with light roller make Sqmt 731.50 216.54
the surface smoothen and light waterning with sprinkler and maintenance
for 30 days or more till the grass establish properly, as per direction of
officer-in-charge.
Providing and fixing pre-cast concrete kerb stone of gray cement based
concrete block 30cm length,30cm height and 15cm thick of M250 grade
42 concret as per approved design and including excavation for fixing in proper Rmt 1,437.70 361.64
line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc
Providing and laying broken chine mosaic flooring for terrace using 12 mm
to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to
plain or slope and to be tempered to bring mortar creme out upto surface
using white cement including rounding off junctions and extending them
upto 15 cm along the wall,clearing with water and oxalic acid etc. as
Carring out plinth treatment to post construction / existing structure by
spraying chemical solution for termite control treatment including labour
and material consistment with I.S.I specification. Using Chlordene and
44 Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent Sqmt 600.27 124.28
is recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1 %
concrentration inclusive of one litre chemical emulsion appication at the
rate of 5 Litre chemical / Sqm of surface is recommended as per I.S
Providing and filling rubbles including hand packing and filling interstices
with quarry spalls behind abutments and between returns as directed.
Providing and laying STONE COATED ROOF TILE - sizing 1340X420mm in
size. fixed with 10mm dia sheet metal screws to the metal structure.
overlapping 20mm to on the under laid roof. cut, chamfered and aligned
with MS structure - truss, rafter, beam etc. (1) 0.50 mm thick sheet.
Supplying and installation of Maccaferri units, made of Mechanically Woven
Double Twisted Hexagonal Shaped Wire Mesh complying with specifications
& testing procedures as per IS 16014:2024, Mesh Type 10 x12, Zn + Polimac.
Mesh Wire dia. 2.7/3.7mm (ID/OD), mechanically edged / selvedged, with
punch strength of 22 kN & tensile strength of 38kN/m, having partitions at
1m interval and shall have minimum 10 numbers of mesh openings per
meter of mesh perpendicular to twist, tying with lacing wire of dia 2.2/3.2
47 mm (ID/OD), supplied @ 3% by weight of gabion unit, including filling with Cum 11,546.00 2,817.90
stones 150- 250 mm in size. Polymer coated wire mesh, when subjected to
neutral salt spray test in accordance with ISO 9227, after 20,000 hours of
exposure the mesh should not exhibit more than 5% Dark Brown Rust (DBR)
and polymer should be resistant to abrasion after 300 cycles and shall not
expose metal wire. (The third-party testing for abrasion resistance of
polymer coating on mesh must be carried out at IIT Bombay in strict
accordance with procedure outlined in IS 16014:2024).
Supplying and installation of Mactex N 30.2 as filter media and placing
48 behind the Gabions and Gabion facia units as per MoRTH 700 Type-III Sqm 6,439.00 75.75
geotextile, The width of geotextile roll shall not be less than 4.5m
Supply and placing boulders of size 150 mm to 250 mm, tying with lacing
49 wires, placing of geotextile at the back side etc. as directed by engineer in Sqm 11,583.00 218.33
Providing & Backfilling behind Gabion units with approved selected fill
50 materialas available within lead of 1-2 km including all leads and lifts, Sqm 2,554.00 289.06
including segregation, complete as per drawing and technical specification.
Earth work excavation for cutting as per drawing/technical specification to
51 prepare foundation of reinforced soil structure, lift and machinery etc. as Sqm 1,254.00 264.82
directed by Engineer in charge
Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes
52 (Medium grade) of the following nominal bore, tube fitting and clamps Rmt 241.00 393.93
including making good the wall ceiling and floor.(C) 25mm
Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes
53 (Medium grade) of the following nominal bore, tube fitting and clamps Rmt 176.00 242.55
including making good the wall ceiling and floor.(A) 15mm
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR
13.5) PIPE having National Sanitation Foundation (NSF) seal for potable
water of following dia. nominal bore tube fittings and clamps including
making good the wall, ceiling and floor etc. complete. [C] 25 mm.
Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR
13.5) PIPE having National Sanitation Foundation (NSF) seal for potable
55 water of following dia. nominal bore tube fittings and clamps including Rmt 270.00 165.21
making good the wall, ceiling and floor etc. complete.[A] 15 mm.
Providing and fixing Gun metal check or non-return fullway wheel valve.(C)
Providing and fixing wash down water closet (European type, W.C. Pan) with
integral P or S trap including
57 jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine Each 13.00 1,290.80
sand) (Seal and cover to be measured and paid for separately)(A) vitreous
China Pattern :(i) in white colour
58 Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan Each 13.00 38.60
Providing and fixing plastic seat and cover for wash down water closer with
59 C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover. Each 13.00 288.45
Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S.
brackets painted white including sutting holes and making good the same
but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v
400mm size. (i) In white colour
61 Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia. Each 25.00 67.24
Providing and fixing Rubber plug for sink or wash basin.
Providing and fixing chromium plated, bottle trap with necessary couplings
of approved quality for wash basin.
Providing and fixing pillar tap, capstan head, screw down high pressure with
screws, shanks and back nuts. (i) 15mm dia.
Providing and fixing screw down bib taps of following size.(A) Brass screw
down bib tap polished bright. (i) 15mm dia
Providing and fixing Urinal of approved quality including connection with
66 trap and with integral longitudinal flush pipe.(A) Squating plate pattern Each 14.00 1,535.63
white earthenware 550mm x 300mm.
Providing and fixing 12.5 Litres low level flushing cistern with a pair, of C.I. or
Mild brackets, complete with fittings such as lead valve less syphon, 15mm
nom.nal size brass ball valve with polythene float, C.P brass handle unions
and couplings for connections, with inlet, outlet and overflow pipes, 40mm
dia. porcelain enamelled flush bend including cutting holes in walls and
making good the same connecting the flush bend with cistern and closet
(overflow pipe to be measured and paid for separately)(A) Vitreous China (I)
In white colour
Providing and fixing chromium plated brass half trun flush cock of approved
quality including fixing in pipe line etc. complete.(i) 20mm dia.
Providing and fixing screw down bib taps of following size.(C) Gun metal
screw down bib tap. (i) 15mm dia.
Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets
70 fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size. or Each 13.00 597.22
20mm inlet.(A) 100mm dia. Each
71 Providing and fixing toilet paper holder.(A) C.P. Brass Each 13.00 414.53
Providing erecting and fixing double coated ISI water tank of required
72 capacity each with all necessary fittings and connection etc. complete on litre 2,000.00 3.91
Providing and fixing Urinal or approved quality including conecting the
73 Urinal with waste pipe , tap etc. complete.(A) White earthenware flat back Each 14.00 1,026.01
or corner type size 430mm x 260mm x 350mm.
Providing and fixing cast iron (Spun) Nahni trap of the following nominal
diameter of self cleaning design with C.I. screaed down or higned grating
including cost of cutting and making good the walls and floor 100mm inlet
and 50mm outlet.(C) 100mm dia.
Providing and fixing 100mm sand cast iron grating for gully, floor or Nahni
Providing and fixing cast iron spigot and socket soil, waste and ventilating
pipes of the following nominal size.(B) 75mm dia.
Providing and fixing cast iron spigot and socket soil, waste and ventilating
pipes of the following nominal size.(C) 100mm dia.
Providing laying (to level or slopes) and jointing reinforced concrete Light
duty non-pressure pipes I.S. class NP2 of the following internal diameter
with collars and butt ends prepared for collar joints including testing of
joints complete.(E) 450mm
Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse
sand : 4-graded stone aggregate 20mm nominal size) foundation concrete
1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside
plastering 15mm thick with Cement Mortar 1:3 (1-Cement : 3-coarse sand)
finished with a floating coat of neat cement and making channels in cement
concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm
79 nominal size) finished smooth complete including curing and festing (i) Each 5.00 10,920.76
Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame
size 560mm diameter total weight of cover and frame to be not less than
128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick
walls of brick msonry using brick having crushing strength not less than
35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type
depth 0.90 Metre for 150mm diameter sewer.
Constructing Manhole with R.C.C. top slab in 1:2:4 mix Constructing brick
masonry chamber for underground C.I. Inspection chamber and bends with
bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover
with frame (Light duty) 455mm x 610mm intenal dimensions total weight of
cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of
frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-
graded stone aggregate 20mm size) foundation concrete 1:5:10 inside
plaster 15mm thick with cement mortar 1:3 finished smooth with a floating
coat of neat cement on walls and bed concrete etc. complete.(i) Inside
dimensions 455mmx 610mm and 450mm deep for single pipe line.
Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight
not less than 35Kg.
82 Providing and fixing in position cowel went to pipes.(C) 100mm dia Each 4.00 496.50
(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling
brickbats with dry masonry work at top for 45cm. height including covering
83 the top with stone including providing vatas in C.M. 1:3 with finishing curing Each 5.00 3,338.80
etc. complete as directed.
Supply, installation, testing and commissioning of ABC 6 KG fire Extinguisher
Supply, installation, resting and commissioning of CO2 4.5 kg Extinguisher
Construction of Septic tank inside dimention of 5 m in length & 2.5 m in
width & 1.5 m depth including excavating any type of soil as shown and
mentioned in the drawing,providing and laying 0.15 m thick plain cement
concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone agg.) M.250
concrete grade slab at bottom with brick masonary 0.230 to 0.450 m thick
walls as shown and mentioned in the drawing CM 1:5 ( 1 cement : 5 coarse
sand ) & RCC Top and bottom slabs 15 cms thick in M.250 (1 cement :
coarse sand : 2 graded stone agg) including reinforcement Fe 500D as per
design and 20 mm thick cement plaster in CM 1:3 using water proofing
compound of approved quality with floating coat of neat cement slurry
inside, top and around tank below 20 cm on ground level, Also provide Two
nos CI Manhole frame and cover of size 60 cm x 45 cm & 75 mm dia. PVC
kgf / Sq cm pressure air vent pipe in 7.00 length with cowl, C-I pipe 100 mm
dia included bend spigot and socket soil, with P & F 12 no. cast iron step of
size 500mm x 150 mm x 22.5 mm with two coat anti corrosive paint etc
complete as per direction of Engineer in charge.
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick
honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m
long complete as per standard design. With common burnt clay F.P.S. (non
modular) bricks of class designation
POINT WIRING FOR LIGHT / FAN WITH MODULAR PLATESWITCHES ANCHOR
/ MK / LEGRAND:
88 Providing and laying point wiring in concealed conduits for thefollowing No. 210.00 520.00
points using specified 1100V grade PVC insulated, FRLSmultistranded 3 x
sqmm copper conductor
Same as above but for 5A socket controlled by one 5A switch on thesame
Same as above but for 5/15A socket controlled by 15A switchindependently
90 mounted including providing wiring with 2 runs of 2.5sqmm and 1 run of 1.5 No. 9.00 495.00
sqmm PVC insulated copper wire through PVCconduit.
Same as above but for AC point with 2 runs of 4 sqmm (P&N) and 1 runof
sqmm (earthing) PVC insulated, FRLS multistrand copper cable in25 mm dia
PVC conduit from MCBDB to 20 A power socket. The conduitshall be
partly/fully concealed in all types o
Supply, laying, and commissioning of wiring using following sizes ofPVC
insulated, FRLS, unsheathed, multistraned copper wire drawn inPVC
conduits. Rate to include supply of 16 GI fish wire, conduits &accessories,
wiring, terminations etc. complete
4 runs of 10 sq mm and 1 run of 6 sqmm copper wire in 40 mm dia
PVCconduit from panel to Distribution Boards
Sweep :1400 mmColour :WhiteBearing type :Double ball
93 bearingDown Rod : Clear 300 mm longRegulator : Electronic type ANCHOR/ No. 36.00 3,200.00
MK makeAccessories : Screws, wall nuts etc.
145Supply, fixing and commissioning of 305 mm dia. Exhaust fansincluding
94 bird louvers, frame works and other civil works like chippingand making the No. 10.00 1,805.50
surface good etc.NOS1570146
LIGHT FIXTURES:
Supply, fixing and commissioning of following light fittings. Rate toinclude all
accessories, interconnection of wires from ceiling rose to thefittings and
fluorescent tube /GLS/PL lamps, copper choke etc
1 x 36 W tube light fitting with lamp Philips make cat no. TCS 19/136HPF or
1 x 60 W Bulk head luminaire including lamp Phillps cat no. NXC
orequivalent (Outside building)
Supply and fixing of wall mounting type meter board made out of 16SWG
CRCA sheet steel and single iron with 3 nos 200A Fuse cutoutsN.L , 1 no.
earth link, 1 no. neutral link and space for accommodating 1no. 3 ph, 4 wire
KWH meter complete with adequa
Supply, erection, testing and commissioning of floor mounting typecubical
panel board made out of 16 SWG CRCA sheet steel with 300 ATPN copper
bus bars, interconnections, earthing, powder coating andcomprising of the
followings as required.(TYPE I AS
Supply, erection, testing and commissioning of floor mounting typecubical
panel board made out of 16 SWG CRCA sheet steel with 200 ATPN copper
bus bars, interconnections, earthing, powder coating andcomprising of the
following as required. (TYPE II A
Same as above but with following details:- Incomer :2 nos 63A TPswitch fuse
unit with HRC fuses for DG and EB / 1no. 63A 4 polechange over switch (on
line) / 2 no volt meter with volt meter selectorswitch / 2 no ammeter with
CT & ammeter selector swi
Supply, installation and commissioning of 63A TPN MCB DB Incomer :1 no
A , 4 Pole MCB Outgoings : 18 nos, 10A/16A/20A SP MCBs
Supply, installation and commissioning of 32A TPN MCB DB Incomer :1 no
A , 4 Pole MCB Outgoings : 12 nos, 10A/16A/20A SP MCBs
Supply and laying following size PVC insulated, sheathed, armouredcable of
approved make (A) 3.5C X 35 sqmm AL cable
105 B 4C X 16 sqmm AL cable MTR 250.00 166.75
105 C 4C X 6 sqmm AL cable MTR 250.00 120.75
105 D 4C X 2.5 sqmm AL cable MTR 250.00 126.50
105 E 3C X 2.5 sqmm AL cable MTR 352.00 115.00
End termination of following cables with double compression NFLPgland and
crimping sockets (A) 3.5C X 35 sqmm AL cable
106 B 4C X 16 sqmm AL cable No 16.00 205.00
106 C 4C X 6 sqmm AL cable No 32.00 140.00
106 D 4C X 2.5 sqmm AL cable No 36.00 120.00
106 E 3C X 2.5 sqmm AL cable No 36.00 115.00
End termination of following cables with double compression FLPgland and
crimping sockets - 3C X 2.5 sqmm copper cabl
Excavation in any type of soil including WBM / asphalt up to 600mmdepth
and 300mm wide including supply and laying 150mm thick sandon top and
bottom of cable, supply and laying bricks laid flat on top,back filling trench
109 Junction box for yard light pole No 190.00 811.90
Supply, Fabrication and Erection of 7 mtrs high galvanised Pole havinga base
plate of size 300x300x16 with 1000 mm long 40mm MS pipesuitable for
mounting 1 no. fixture as per attached detail specificaton.Job also includes
foundation for the same. Pol
Street Light Fitting.
P/f 7 mtr high hot galvanised octagonal pole, continously tapered (bolt fixing
type) in single
111 section made out of 3mm thick sheet suitable for bracket having top dia 70- No 65.00 10,925.00
bottom dia 130-150 mm, base plate size 220X220X12 to 240X240X16 mm
GRID CONNECTED SOLAR PHOTOVOLTAIC POWER PLANT.
'Supply, fitting, fixing of 325 Wp modules (200KWp) with hot dipped
galvanized 'module mounting structure, lightning & over voltage protection,
earthling protection as per 'specification.'Design, manufacture, supply,
installation and commissioning of required nos. of String 'Inverter 3 Phase
Power Conditioning Unit comprises of solar charge controller cum Inverter,
'full sine wave 415V, three phase 50Hz AC Output with grid tied feature
112 along with all 'protection, controlling arrangement and required accessories. Kw 30.00 49,775.00
'Design, Manufacture and supply Junction boxes, Distribution boxes, Cables,
Lugs and other 'Hardware’s etc. 'Integration of various equipment’s &
components and commissioning of the power plant 'including tit –bit items
for Installation and commissioning of plant on TURN_KEY basis. 'The Cost
include the all the charges related to the obtaining necessary approvals from
'Government authorities and to acquire the facility of net metering. 'Refer
attached specifications with Five Year Operation & Maintenance.
Supplying and erecting, commissioning and testing of Diesel Generating set
confirming to IS: 4722:1968 & BS:5514 having continuous rating, 3 phase,
415 volts, 50 cycles A.C. supply comprising of a totally enclosed air/water
cooled diesel engine with multi-cylinders developing suitable BHP not less
than following capacity at 1500 RPM with 10% overload for one hour in
hours with standard accessories like fly wheel, lubricating oil cooler, "A"
class governor, heavy duty fuel wheel and lubricating oil filter, oil bath air
filler, lubricating oil pressure gauge, end exhaust manifold, standard set of
tools with adjustable spanners, screw drivers, cylinder head to cover, joint
cylinder head to exhaust, element lube oil filter, 12 / 24 volts electric
starting equipment complete with standard heavy duty battery, dynamo, cut-
outs, ammeter, necessary wiring, pressure gauge, starter etc and heavy duty
Residential type exhaust silencer and vertical hot air duct both indicator
lamps duly wired with HRC fuses.
The alternator & control panel shall be connected with provided suitable
capacity armoured cable and complete with Acoustic enclosure (canopy)
made out of 16 SWG CRCA Sheet, sound absorbing material Rockwool of
density & 100 mm thick conforming to IS:8183 / PU Foam of 40 Density - at
least 40 mm. The resin bonded rockwool covered from inside the canopy by
perforated sheet with 3/4 mm holes, sound level not more than 75 dB at a
distance of 1 mtr, as per PVCT norms. Erection, commissioning and
satisfactory testing as per requirement with first filling of fuel, oil, etc. with
guarantee / Warrantee of complete system for Two years. & with obtaining
all necessary certificate from Electrical Inspector. The Capacity and Ratings
of DG sets are as below. (M) Continuous rating of 125 KVA ,BHP not less than
154 BHP(M) Continuous rating of 125 KVA ,BHP not less than 154 BHP
Supplying submersible pump set for bore of 200 mm. dia. or more having
phase motor capacity about 25 H.P. and discharge capacity having (A) (12
Stage) 472 to 330 L.P.M. discharge at the head 120 to 192 mtrs. suitable for
65 mm dia. delivery pipe Cat III
Providing & erecting open well horizontal mono block pump set with cast
iron body, complete for three phase submersible motor having [A] For
HP 3 phase open well horizontal mono block pump set suitable for 190 LPM
@ 20 mtr head suitable for 40 mm dia delivery pipe Cat.II
I/We am/are willing to carry out the work at… % above/below percent (Should be written in figures and words) of the estimated rate mentioned above. Amount of
my /our tender works out as under.
Estimated amount put to tender Estimated amount put to tender
Deduct………% below Add………% Above
In words In words
1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no extra payment shall be made.
2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.
3 GST and Income tax TDS will be deducted at a source while making payments of bills
4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement Consumption/16/C, Date:11/05/2017 as
stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost of difference of cement consumption have been deducted from the
rate of original item at the rate of input rate mentioned in all the tender.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
01 Notice Inviting Tender.pdf
04 Technical Specification Annexure.pdf
05 General Electrical Booklet.pdf
08 All GR.pdf
Building Constn.pdf
Building-Specification Booklet (2 side) OK.pdf
Extra Access GR.pdf
GR - Steel Lap Calc.PDF
GR GST 1.pdf
GR PQ.pdf
GR.pdf
GR1.pdf
Khanij Royalty.pdf
Khanij-Royalty1.pdf
Materials Make (Civil Elec Plumbing).pdf
Performance Bond and Bitumen date.pdf
RBM-Board.pdf
WIlson HIll SBD Book.pdf
Wilson hill Admin Area Drawing.pdf
Wilson hill Drawings.pdf
Wilson hill Site plan.pdf
Wilson hill Site Section.pdf
wilson hill Toilet Block Drawing.pdf
Wilson Hill BOQ.pdf
Download all tender documents and submit your bid