Risk of Cost Special repair to 14 guard posts of certain unit at Banar in Army Area Jodhpur

Amount

Taking down chowkats or frames with shutters area n exc 1 sqm each as in ventilator of any size and description

S&F 35mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of member as sped in SSR part-I section 8, clause 8.24(a).

S&F 35mm thick factory made, second class hard wood, plain framed, paneled shutters (any number of panels) with lock rail and panel of 9mm BWP commercial ply as specified in particular specifications or 12mm veneered particle board with commercial veneering on both faces. The size of rail and styles shall be as per IS:1003 (Part I), Kiln seasoned and chemically pressure treated.

S & F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement of stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top roil and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification.

S & F 01 mm thick steel cupboard including handle, mortice type locking arrangement (two set key) and frame including two coat of synthetic enemel paint over one coat of red oxide and taking down from existing place including making good the existing surface.

S&F rolled section of Gde Fe-310-0 or Fe 410-0 in framing for cladding, glazing and the like fixed with angle cleat and connecting plate etc (Door frame/chowkats with hold fasts, flat iron for fixing hinges, cooler stand) etc. Note: the rate quated shall be deemed to including making holes for insterting hold fasts and making good the surfaces of cills, jambs, wall etc.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars dovetailed or welded.

S&F factory made steel window with side hung shutter including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded.

S&F factory made steel ventilators with top hung shutters including hinges, steel peg stay complete.

M&L for framedwork such as grills, grating, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, and similar work conforming to Fe 410-0 or Fe-310.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with stainless steel wire staples

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc. 0.50 Sqm in each pane.

All as per item No 12 above but figured, pin head type and glazing with oil putty or wooden beads, in squares n.exc. 0.5 Sqm in each pane.

S&F 300mm long mild steel sliding door bolts plate type, stove enameled black with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate.

S&F 150 mm long mild steel barrel tower bolts stove enameled black with bright bolt all as specified.

S&F 100mm size butt hinges, medium weight cold rolled mild steel (ISI Marked) all as specified.

S&F 150 mm size mild steel pressed handles, oval type, stove enameled black.

S&F 150mm size (overall length of cover plate) floor door stopper of aluminum alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section.

S&F 150mm size aluminium handle extruded alloy, fabricated type anodised.

S&F 19/20mm internal dia PVC coated drapery rod of aproved make including PVC curtain ring any colour suitable for 19/20mm internal dia drapery rod & 10 Nos/per meter length including curtain bracked fancy type with adjustable threaded socket use for 19/20mm internal dia drapery rod complete (Two Nos of brackets for one length/Each

M&L for preparation of new wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of pink wood primer all as specified.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide primer.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc. 15cm thickness (below or above ground level) and removing from site

M&L for non skid ceramic colour tiles 7 to 8mm thick (Square & Rectangular) area of each tile exec 0.18 Sqm but n.exc 0.38 sqm in floor etc set and joint in neat cement slurry and pointed in white or colour cement to match 15mm thick screed bed in CM 1:6 complete all as specified by Engr-in-Charge

All asper item No 25, above but on vertical surface as in skirting/Dados over 10mm thick plaster in CM 1:4

M&L for colured glazed ceramic tiles in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match 10 mm thick screed bed in CM 1:4 on vertical surpfaces of wall complete all as specified directed by Engr-in-Charge

S&F in repairs vitreous china squatting pan, 'Orrissa ' pattern, size 580 x 440 mm white , with integral foot rests complete including provision of lime concrete beding, including connection to P or S trap, and to flushing pipe, anti-syphonage pipe, etc including maing good to floors all as specified and directed.

M&L machine cut Kota stone 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete (mirror face) as in cooking platform, window cills , stair step and riser over 15 mm thick screed bed in CM 1:6

All as per item No 29, above but as skirting in 10mm thick screed/plaster in cm (1:4)

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set in grey cement and pigment, jointed and pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed

M&L for 50mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, concrete shall be laid in alternate bays n.exc. 3m in length, finished fair and even.

Demolition of RCC roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removing from site.

M & L for RCC 1:2:4 type B1 (20 mm graded stone aggregate) as in roof slab, chajja, shelves, facia, landing, balcony and similar articles including necessary form work, props/scaffolding reqd upto roof of 1st floor and including cutting for enlarging opening for providing fins & Facia for applying rust remover, epoxy bonding, drilling reinforced TMT Bars, and make with existing finishes all as directed.

M&L Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending, spirally for hooping for coloumns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete.

All as per item No 35, above but 8 mm to 10 mm .

Taking down cement plaster/wall tiles from concrete/stone surfaces including raking out joints, hacking for key, scrubbing down with water etc and its removal from site as spfd & directed.

M&L for 15mm thick rendering in CM 1:6 on stone surface and surfaces finished even and smooth without using extra cement.

M&L for 10 mm thick plaster on ceiling in cement mortar (1:4) finished even and smooth without using extra cement.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on wall.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceillings.

M&L preparation of old decorated surfaces of walls (plastered of unplastered) including cornices, pillasters etc by bromming down or wire brushing removing dust, dirt etc scrapping smoke, scot, moulds, moss and efflorecent salts, removing oil and greasy spots and applying three coat of distermper dry (white or tint as directed) on walls complete all as specified and directed.

M&L preparation of old decorated surfaces of walls (plastered of unplastered) including cornices, pillasters etc by bromming down or wire brushing removing dust, dirt etc scrapping smoke, scot, moulds, moss and efflorecent salts, removing oil and greasy spots and applying two coat of colour wash on walls complete all as specified and directed.

Taking down 40mm bore galvanized steel water tubing with all fitting fixed complete to wall and ceiling or laid in floor

S&F 20 mm bore galvanized steel water tubing with all fitting fixed complete to wall and ceiling or laid in floor

All as per item No 45, above but 40 mm bore

S&F in repair 40mm bore stop valve, cast copper alloy (ISI marked) screw down high pressure with crutch or butterfly handle, screwed both ends (externally threaded) for iron pipe or for unious.

S&F in repair PVC low level flushing cistern, 10 litre capacity, symphonic action type, white inlet valve, float, handle,15mm dia PVC connection 450mm long, 15mm dia cast copper alloy chromium plated stop valve and 32mm dia PVC & flushing pipe including fixing of long screw chromium plated.

S&F in repair 15 mm bore bib taps, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S&F gun metal globes or gate valves with iron wheels head, screwed both ends for iron pipe and fixed for 20mm bore GI pipe

M&L PTMT(Float) valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferruly and fixed for 20mm GI pipe all as directed at site

Cutting existing GI pipe 100/80mm for insertion of new GI fitting any type all as directed at site

M&L for brass chromium plated shower rose 80 mm size with swivel joints including fixing to steel pipe of 15mm bore in repairs.

Raking out cement joints/pointing to squared rubble coursed masonry or uncoursed masonry work built in cement mortar.

M&L for keyed pointing in CM 1:3 to squared rubble masonry, coursed or uncoursed

M&L Plain cement concrete (1:3:6) type CI using 20mm graded stone aggregate as in hold fasts, roof kerbs, golla vatta.

Dismantaling of 100mm dia cast iron pipes, jointed in cement mortar or lead joints and taking out of trenches if required.

All as per item No 57, above but 75mm bore

M&L 100mm bore CI pipe and vent pipe sand cast pipe in any length with or without ears with cement joints to wall or laid in trench or as directed

All as per item No 59,above but 75mm bore

M&L cost irom bends diminishing pieces or tappers of pipe 75mm bore with oval access dorr

S&F Stack Clamps out of (50mmx5mm) flat iron and 12mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for pipe 100mm bore .

All as per item No 62 above but for 75mm bore pipe.

M&L for cast iron cowls for 100 mm bore of pipe.

M&L cast iron floor trap with grading including jointing to waste pipe fixed in cement concrete type BI (1:2:4) using 20mm graded stone aggregate dia of outlet in 100mm.

M&L for cast iron nahani trap with grating including jointing to waste pipe fixed in cement conctete type B-1, 1:2:4, diameter of outlet in 100mm.

M&L for PCC type D2 1:4:8 (40mm graded stone aggregate) in foundations, filling and mass conctete

M&L for 150mm internal diameter of saltglazed stoneware drain pipes laid in trenches and jointed as specified

M&L for concrete bed to drain pipes including packing under and hunching against the, side of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate for 150mm bore SGSW pipe

Dismantaling PVC water tanks exc 250 Litre capacity but not exc 500 Ltr capacity and removing to site.

S&F ISI marked 500 Litre capacity rotational moulded polyethylene water storage tanks white in colour (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball brass float valve high pressure.

M&L rendering 15 mm thick in cement mortar 1:3 on roof surfaces finished even and smooth without using extra cement mixing with water proofing compound.

M&L for painting with blown type bitumen conforming to IS -702 grade 85/25 @ 1.20 Kg/Sqm including a coat of bitumen primer conforming to IS 3384 @ 0.40 ltr per sqm, third layer of APP modified polymeric membtane having centre core of 20 micron HMHDPE outer film 20 micron each thickness 1.5 mm having weight 2.25 Kg/Sqm and Fourth coat of bonding material using blown type bitumen conforming ti IS -702 grade 85/25 @ 1.20 Kg/Sqm and a fifth and top most of PCC tiles 22 to 25 mm thick (hydraulically pressed) laid over 15 mm thick layer of cement mortar screed 1:3 joint of tiles shallbe 4 mm wide and grouted with CM

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L for point wiring complete with 1.5 sqmm single core mulfistranded copper conductor PVC (FRLS) insulated and unsheathed cable in and incl PVC casing caping fixed on wall, surface, ceiling etc including 3mm thick, laminated Hylen sheet for mounting switches, sockets, regulator etc on existing sunk cast iron terminal boxes with 1.5 sqmm single core multistranded copper conductor PVC insulated and unsheathed cable as earth continuity conductor to common earth and earth dolly for:- (a) One light point contolled by one, oneway switche single pole

(b) One Fan point contolled by one, oneway switch single pole

(c) One 3 pin, 5 Amp socket outlet on same board

(d) One 3 pin, 5 Amp socket outlet on independent board

(e) One 3 pin, 5 Amp socket outlet on same board

M&L for point wiring complete with 4.0sqmm single core multistranded copper conductor PVC insulated and unsheathed cable 1100v grade fixed on and including PVC capping casing fixed on wall surfaces ceiling etc for existing MCB enclosure/ socket board with 2.5 sqmm single core multistranded copper conductor PVC insulated and unsheathed cable as earth continiuty conductor to cmmon earth and earth dolly. (for AC/Geysers point)

Supply and fixing switch Piano flush type 5 Amp single pole.

Supply and fixing multipurpose socket outlet with piano flush type 3 pin 5 Amp all as specified

Supply and fixing switch socket combination 3pin 16 amp flush type 5 in 1 all as specified

Supply and fixing ceiling rose surface backelite 65x17.5mm three terminals all as specified and directed.

Supply and fixing fan regulator electronic type for ceiling fan 1200 mm sweep of Make Anchor/Cromp/Cona

Supply & Fixing in repairs LED tube light is energy efficient alternative to LT8-16watt fluorescent tubelight with same form factor & appearance box type with and including electronic choke 240V, side holder connector block and lamp complete in replacement of existing u/s fittings including provision of 23/0.0076 flexible wire twin core, PVC insulated multistranded copper conductor cable 1100V from tube light fitting to ceiling rose Make : CG/Philips and wipro.

M&L for replacement of existing u/s any type and make security lights fitting and Supply and fix at any height on pole of any type and height from 7 Mtr to 9 Mtr LED based street light fitting having IP 65 protection class with the apoxy power coated housing inclose with glass cover in frame, 40W mounted on MCPCB suitable for 50mm outer dia pipe and minimum lumirious efficency of 90 lumens/W and the matrix of Leds having a minimum out put of 40 W and capable of producing a constn & lux in the voltage range of 180 V to 280 V at 50Hz and suitable for operation in a temprcture range of 5°C to 50°C RH range of 10°% to 90% and injection temp not grater tha 80°C including mounting the LED light fitting on a 50mm dia GI pipe bent to shape and material and lobour for connecting the light fittings to Junction box to brackets using twin core multi stranded flat weather proof aluminium of size 4 sqmm duly passed through the brackets through holls drilled for entry and exits of the cable so as to concealed the same. Make : Philips/Crompton

M & L for Lamp holder PVC/polycarbonate type with back plate suitable for batten fitting all as directed.

S & F High lumen LED Bulb, 5 Watt E27C5 with E27(Screw cap) Base. CCT-230V decorative wall mounting type with multicolour ABS housing with poly carbonate rings and glass shade with lamp holders, connector block etc complete will all accessories prewired and including connection up with twin core twister flexible copper conductor cable with suitable size all as directed. Make : CG/Philips and wipro.

S&F pre-wired distribution board in sheet metal encl, prewired when MCB to be used with 200Amps rated copper bus bar confirming to relevant IS SPN 8 Way, Cat No -SD3706, Make : Legrand/ Siemens.

S&F MCB 10 KA rupturing cap ISI marked 'C' series for MCB SPN 32 Amps

All as per item No 91, but MCB SP 5 to 32 Amps

M & L Sub main wiring with two single core 4 mm FRLS PVC insulated and PVC unsheathed multistandred copper conductor cable drawn through and including casing capping fixed to the surface of wall/ceiling as per ISI including one run of 2.5 sqmm copper conductor unsheathed earth continuity conductor including taking down of existing sub main wiring.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm× 6mm burried directly in gound (earth pit not less than 2.25mtr deep below normal gound level) with top edge of the plate not less than 1.5mtr below normal gound level connected to galvanised earth lead GI wire 4mm by nut and bolt check nut and washer of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I connected to earthing test point on pole including PCC pit (1:3:6) type C1, with RCC cover in lieu of CI cover and frame with necessary excavation and earth work in any type of soil complete all as specified and directed by Engr-in-Charge

S & F High lumen LED Bulb, 7 Watt lumen out put voltage ranging 180- 270volt with E27 A10 (Screw Cap)Base.CCT- 230V decorative wall mounting type with multicolour ABS housing with poly carbonate rings all as directed. Make : CG/Philips and wipro.

Material and labour for GI pipe light grade 50mm dia for cable protection with suitable bracing clamps on wall/pole including cold drilling and making good surface as per existing complete all as specified and directed by Engineer-in-Charge.

S&F having connectivity passing through pipe, 1100volt grade heavy duty cable with XLPE aluminium conductor surved with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16sqmm 2 core nominal cross section in service connection inlcuding lug etc complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M depth in soft/loose soil and getting out for laying GI strip conductor, stay, poles etc all as specified and directed.

Returning, filling in including spreading laveling, watering and well ramming in layers not exceeding 25cm in of soil all as specified and directed.

Removing excavated material n.exc. 50M and depositing where directed at a level n.exc. 1.5M above the starting points.

M&L for clean, dry sand in trenches/ducts for cushioning to cable complete all as specified.

M&L for jodhpur stone patti slab cover 25cm to 30cm in width, 60cm long and 40 to 50mm thick laid in trenches for cable protection.

Water heater storage type, electric supplied and installed complete capacity 25 litres. Make : Havells/Bajaj/Philips

Supply and fixing of brass chromium plated connecting PVC wire reinforced pipe (not less than 30cm & nut exc. 50 Cm,s) with two coupling nuts with washers suitable for 15 mm bore of pipe. Make: GIM/L&K/MANSA/SEIKO

Supply and fixing of PVC (Heavy duty) wire reinforced pipe connection white 45 cm long with two No,s brass coupling suitable for cold water for 15mm dia pipe.

Supply and fixing of exhaust fans AC single phase 230/240 volts of size 300mm sweep with louvre all as directed by Engr-in-Charge. Make : Havells/Bajaj/Philips. Replacement items to be deposited to AGE E/M store yard.

Tirupati electricals works and services

D DEV COMPANY