REPAIR TO OF EXTERNAL ELECTRIFICATION (LT WORKS) AND STREET LIGHTS OF ENTIRE AREA OF RANIKHET UNDER GE RANIKHET

Amount

BOQ ( Sch A ) Electric works Excavation in trenches not exceeding 1.50M wide and not exceeding 1.5M depth in hard/dense soil and getting out for laying pipes, cables etc and fitting including forming bottom surface to required level and slope complete all as specified and directed.

Returning, filling in, trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above starting point complete all as specified and directed..

Supply, laying, jointing and commissioning LT XLPE 1100 volts grade heavy duty cable PVC insulated, stranded aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing cross sectional area 500sqmm 3½ core laid in trenches, floor through pipes,in duct, on pole and roads etc including making good as per existing complete all as specified and directed. Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for the same. 2. Excavation, earth work, sand cushioning and brick protection will be measured and paid separately under respective items

All as per Srl item No 4 here-in-before but sectional area 400sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 300sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 240sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 150sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 120sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 95 sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 50 sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 35 sqmm 3½ core

All as per Srl item No 4 here-in-before but sectional area 25 sqmm 4 core

All as per Srl item No 4 here-in-before but sectional area 16 sqmm 4 core

All as per Srl item No 4 here-in-before but sectional area 16 sqmm 2 core

All as per Srl item No 4 here-in-before but sectional area 10 sqmm 2 core

Material and labour for sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as specified and directed. Note :-Punned down thickness of sand shall be considered for measurement)

Material and labour for brick protection to cable using old size class 'B' bricks, laid flat, dry butt jointed, laid lengthwise perpendicular to the axis of cable complete all as specified and directed by Engineer-in-charge.

Taking out unserviceable LT cable of any type and size from pole/wall/trenches by disconnecting electric connections for repair / replacement of cable complete all as specified and directed.

Material and labour for stringing, stretching and strengthening of overhead conductor (ACSR) on existing LT steel tubular pole including binding and jointing the conductor with and including 14 SWG binding wire and following sizes ACSR conductors: - (a) 6/1 X 2.59 mm aluminium and 1 X 2.59 mm steel (Weasel) (b) 6/1 X 3.00 mm aluminium and 1 X 3.00 mm steel (Ferret)

Dismantling / taking out old ACSR conductor / copper conductor / GI earth wire any size from existing overhead lines including disconnection complete all as specified and directed.

Supply and fixing shackle type insulator, porcelain, vitreous, white, brown or green insulator of size 75 mm height and 90 mm dia for working pressure of 1100 volts, LT complete with galvanised mild steel strap of size 31 X 3 mm / flat iron 50 X 6 mm ‘D’ clamp or ‘U’ clamp of suitable size and holding clamp, washers, insulator bolts of 12 mm dia, washers and nuts complete all as specified and directed.

Tightening / re-stringing of existing loose / broken ACSR conductor / copper conductor or any other type of conductor of any sizes and strengthening as required at site complete all as specified and directed.

Supply & Fixing in replacement plastic (moulded polypropylene) line phase separator (for separating 05 Nos. of over head line conductors of length 1200 mm) with 25 mm fly nuts and clamps suitable for 1100 volts grade LT electric lines of any size fixed with over head electric lines complete all as specified and directed.

Supply and fixing / laying of galvanized iron pipe of 80 mm nominal bore light grade for cable protection, fixed to pole/ alongwall/ floor/ under road/ across the drain or nallaha etc with clamps nuts, bolts and washers complete all as specified and directed. Note : The cost of MS clamp, nut, bolt, washer and GI fittings etc shall be included in the item rate.

All as per Srl item No 25 here-in-before but 50mm nominal bore of pipe

All as per Srl item No 25 here-in-before but 40mm nominal bore of pipe

All as per Srl item No 25 here-in-before but 25mm nominal bore of pipe

Material and labour for supply, transporting, erecting truly in vertical position and fixing of steel tubular pole swaged, over all length 9 metres, type 410 – SP – 31 complete with mild steel base plate, pole cap, finial taper plug, MS bolts, nuts & washers, necessary excavation & earthwork in hard / dense soil, PCC sub base block as mass concrete of size 600 X 600 X 150 mm in cement concrete 1:4:8 Type D-2 in base of foundation, PCC foundation block of size 600 X 600 X 1500 mm in cement concrete 1:3:6 Type C-2, pole plinth of size 600 X 600 X 300 mm in cement concrete 1:2:4 Type B-1 including necessary form work as required at site and painting of pole with two coats of anti corrosive black bituminous paint through out internally and externally upto planting depth (embedded in concrete) and remaining portion of the pole painted two coats of aluminium paint over a coat of red oxide primer on complete exposed surface including painting of 05 Nos. bands / strips of 30 cm wide each with two coats of synthetic enamel paint (black & yellow) at a distance of 30 cm from plinth block upto 1500 mm height and marking / sign writing of pole number and feeders locations of pole with thick synthetic enamel paint (white) complete all as specified and directed.

Supply and fixing stay assembly comprising of GI stay bow 14mm dia, 40cm long, galvanised stay rod 16mm dia, 180cm long with threaded ends, GI nuts, bolts, washers, GI stay plate 23x23cmx6mm thick, 02 Nos of thimbles, MS clamps made out of 50x6mm flat iron and stay wire 7/3.15 SWG, stay clamp, loop insulator of size 65x95 mm clearance of hole 16mm complete including necessary excavation, earth work in hard dense soil and PCC 1:3:6, type C-2 all as shown in electrical plate No. 01 of SSR-2009 part1 , complete all as specified and directed.

Supply and fixing guard cradles, make to shape, hexagonal / rectangular or any other shape as required and directed, fabricated out of 4 mm dia GI wire including 14 SWG binding wire complete all as specified and directed.

Dismantling of existing stay assembly any type / size from its stay rod, cutting stay rod (above ground portion) dismantling of MS clamps, nut-bolts, stay bow, loop insulators, stay wire etc. complete all as specified and directed.

Dismantling / taking out of old LT steel tubular pole any type and any size from foundations including dismantling of concrete, MS clamps, nuts-bolts, earth wire, over head line conductors, insulators, guarding cradles and other accessories including necessary excavation and earth work in any type of soil complete all as specified and directed.

Dismantling / taking out old unserviceable insulator of any size / type from existing electric LT lines complete all as specified and directed.

Material and labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick burried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate), GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed Note: - On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

Material and labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick burried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth strip 32 X 6 mm size by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate), GI protection pipe light grade 40 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note: - On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

Material and labour for MCCB of Cap 100 Amp, 4pole, 415 volt, 16 KA, complete all as specified and directed.

Material and labour for replacement of MCCB of Cap 200 Amp, 4pole, 36 KA, with adjustable thermal release and earth fault protection, 415 volt grade including cutting and welding work for fixing of MCCB in existing panels any type and model complete all as specified and directed.

All as per item No 38 here in before but cap 250 Amp,36 KA

All as per item No 38 here in before but cap 350 Amp, 36 KA

All as per item No 38 here in before but cap 400Amp, 36 KA

All as per item No 38 here in before but cap 630 Amp, 50KA

Supply and fixing cable end jointing kit for LT XLPE grade cable for heat shrinkable complete with jointing materials and accessories suaitable for 3.5/4 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm complete all as specified and directed.

Supply and fixing cable end jointing kit for LT XLPE grade cable for heat shrinkable complete with jointing materials and accessories suaitable for 3.5/4 core XLPE armoured aluminium conductor cable of size 120 sqmm to 240 sqmm complete all as specified and directed.

Supply & ffixing in replacement Automatic Elecromechanical street light timer switch complete in all respect consisting of time switch contactors 01 No, toggle switch 3 No of appropriate capacity and input and output terminals completely wired with a bakelite sheet with copper wires of suitable cap. Time switch and the unit should be encased in weather proof MS sheet cabinet with lockable front door opening, paint with one coat of anti corrosive solution one coat of red oxide primer and two coats of synthetic enameled paint duly spray painted and provision for cable entry and attachment with the existing pedestal time lite distribution board timelite 65 A, 3 pole/230 V digital switch complete all as specified and directed. Make :- Indo Asian cat part No TL065DBO or equivalent cat part in make Havells, HPL

Supply, fabricating and fixing of sheet metal encluser made of 16 gauge MS sheet outdoor type of suitable size including fixing of MCCB of cap 200 Amp, 415 Volt,50Hz, 4 pole, 36 KA, AC supply with 300 Amp rated busbar on porcelain insulators for neutral link double door type with locking arrangement complete with MS angle iron frame of size 25 x 25 x 5mm with nut/bolts and PCC plateform work including painting with two coat of synthetic enameelled paint over one coat of red oxide/ primer complete all as specified and directed at site.

Material and labour for stringing, stretching and strengthening of GI wire 4mm dia on LT electric lines including binding, jointing etc complete all as specified and directed

Material and labour for preparation of old painted steel and iron surfaces and painting to steel tubular LT poles of any height 9/11/13 metre, ant type (double swan / single swan) with two coats of synthetic enamel paint upto 1.5 m height above form ground level (in yellow and black strips of 30 cm wide each) and applying two coats of aluminium paint above 1.5 m height of poles including painting on cross arms, bracing, clamps etc and writing pole Nos. with thick black synthetic enamel paint complete all as specified and directed.

Cutting/ trimming of tree branches of any width/ girth up to 1.0 mtr distance on both sides of HT/ LT over head lines including collection and depositing the retrieved timber at a place as directed by Engr-in-charge. Note :- (i) Each span have a distance 40mtr approximately (ii) All cutting branches of trees shall be thrown away/ burnt at approximate 200 to 500 mtr away as directed.

Supply and fixing of junction box made of high quality thermoplastic polycarbonate enclosure with IP 65 degree of protection, weather proof, corrosion proof, dust proof, insulated and shock proof, fire retardant non toxic material with internally embaded gasket with 10 Amp MCB and 4 Nos terminal of size 200x160x98 mm including taking down of old unserviceable junction box complete all as specified and directed. Make:- Hensel, sintex, universal

Supply & Fixing LED street light fitting 45pressure die cast aluminium IP66 roadway luminaire with operating range from 80V to 440 V AC high power LED as light source and electronic driver including GI bracket light grade 25/32/40mm and provn of electric supply to fitting from source by means of PVC Sheathed multi-stranded copper conductor cable of 2 x 2.5 core complete including taking down existing old light fitting any type all as specified and directed. Make :- Havells cat part No ELEKTRASL45WLED757SASYBOPC or equivalent cat part No in make specified in particular specification.

Supply & Fixing LED street light fitting 30/35W pressure die cast aluminium IP66 roadway luminaire with high power LED as light source and electronic driver including GI bracket light grade 25/32mm and provn of electric supply to fitting from source by means of PVC Sheathed multi-stranded copper conductor cable of 2 x 2.5 core complete including taking down existing old light fitting any type all as specified and directed. Make :- Havells cat part No VILUMINASL30WLED757PASYBOPC or equivalent cat part No in make specified in particular specification.

Supply & Fixing LED Flood light fitting 100W 230 V AC outdoor type pressure die cast aluminium IP66 luminaire with high power LED as light source and electronic driver with impacy and corrosion resistant including GI bracket light grade 25/32mm with clamp and provn of electric supply to fitting from source by means of PVC Sheathed multi-stranded aluminium conductor cable of 2 x 4sqmm core complete including taking down existing old light fitting any type all as specified and directed.

Taking out old unserviceable service connection cable for replacement including Supply & Fixing service connection cable, 1100 volts grade heavy duty PVC insulated aluminium conductor, 16 Sqmm 2 core size, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular, complete all as specified and directed.

Supply and Fix Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in coping of pole, floor including necessary form work where required and fair finish to the exposed surfaces all as specified & directed.

Supply and fixing synthetic insulating mat near electric installations of size 2m x lmX 3mm thick as specified and directed.

Supply and fixing synthetic insulating mat near electric installations of size 2m x lmX 2.5mm thick as specified and directed.

Material and labour for Anti-climbing device,spikes type fabricated out of M.S bars (round, square and flat) including nut, bolts, washers and welding in two halves made to shape to suit the cross section of the pole complete all as specified

Supply and fixing for LT lightining arresters for outdoor use, expulsion type complete with all fittings, 30 Kiloamp discharge capacity distribution class complete all as specified and directed.

Supply and fixing in replacement for ELECTRIC SHOCK CHART (Electric shock & its management chart) of standard size 70x50 cm drawn on wooden/ cardboard frame of approved size complete all as specified and directed.

Material and labour for repair of old street light 25-50W capacity by replacing old unserviceable driver / LED plate or any other items as and when required on site and making it serviceable and fixing it on pole after repair complete all as specified and directed

Material and labour for repair of old street light/ flood light /High way light 60-150W capacity by replacing old unserviceable driver / LED plate or any other items as and when required on site and making it serviceable and fixing it on pole after repair complete all as specified and directed

Writing letters or figures (Block Roman, Italic or Indian) n exc. 30 cm high incl preparation of surface and making the base to receive letters by applying synthetic enamel paint. Letters etc shall be paint with thick paint complete all as specified and directed.

Supply & Fixing in replacement for ELECTRIC SCHEMETIC DIAGRAM/CHART HT/LT supply system of Ranikhet station , made in such a way so that it contains all the information like sub station, MRS OCB/VCB, Transformer , over head and under ground line on wooden board back side and acrilic sheet (tampered proof) front side with proper indicating lamp for all the feeders and connected equipments with on/off swich for all the feeders/segments. Size of the board shall be standerd as per sample held with MES office or 4ft X 4ft. Before making board contractor shall deploy a qualified engineer/firm or any technocrate for site survey and and making rough diagram on drawing sheet and get it approved from engineer-in-charge before making original board. Complete all as specified and directed.

Supply and fixing of LED Post top 40W with IP 65 protection comprises of Spherical/Diamond shape diffuser cover, etc and all accessories including monkey cage of suitable size for protection of light, light grade GI pipe of suitable length and wire required for connections etc complete all as directed.

Supply and fixing of LED Bollard light suitable for 20-30 watt LED bulb ( with 20-30 W LED bulb) including B-22 brass holder provided with aluminium cover, fully cast aluminium body finished with polyurethane paint ( with prior treatment) bollard of length 584mm ( 23 inches) & Hexagonal base dia of 279mm ( 11 inches) and max dia of leg of bollard 133 mm ( 5.25 inches) surmounted with fully cast aluminium body finished with PU paint with acrylic window cover, IP 65/66 protection complete all as directed. Make :- Mapro cat part No MBL-T-280

Material & labour for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with stranded copper conductor 2.5 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 2.5 sqmm multi - stranded copper conductor as earth wire in green colour including taking down existing unserviceable sub main wiring complete all as specified and directed. NOTE: (Note :- 2 runs of 2.5 sqmm single cable, one run of 2.5 sqmm earth wire cable and PVC conduit shall be considered as one unit/1Rm)

Supply, installing, testing and commissioning, factory made and tested (prototype having been CPRI type test certified), LT feeder pillar box (KIOSK), outdoor type, platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber with insulated copper bus bars suitable Amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, IP 65 class protection and made of 3.15mm CRCA MS sheet and 40x40x6mm thick angle iron frame work, externally powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement (including provn of 65mm Godrej (Freedom) lock with 2 keys, internal wiring 2.5 Sqmm with PVC insulated, solid copper conductor, FRLS cables, IS-694 marked of adequate size incl the provision of space to accommodate the under mentioned items incl taking out old one and making connection with existing LT cables . The panel shall includes the following:-

Item 69 ( contd ...) (c) Platform for the panel with PCC 1:4:8 type D-2 with 40mm graded crushed stone , 15 cm thick in foundation, brick work in CM 1:6 with sub class `B', old size bricks, rendering 15mm thick in CM 1:6 on exposed surfaces and 100mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45cm above the nearest road level. Note : (i) All out going feeders shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint.

Supply, installing, testing and commissioning, factory made and tested (prototype having been CPRI type test certified), LT feeder pillar box (KIOSK), outdoor type, platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber with insulated copper bus bars suitable Amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, IP 65 class protection and made of 3.15mm CRCA MS sheet and 40x40x6mm thick angle iron frame work, externally powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement (including provn of 65mm Godrej (Freedom) lock with 2 keys, internal wiring 2.5 Sqmm with PVC insulated, solid copper conductor, FRLS cables, IS-694 marked of adequate size incl the provision of space to accommodate the under mentioned items incl taking out old one and making connection with existing LT cables . The panel shall includes the following:-

Item 70 ( contd ...) (c) Platform for the panel with PCC 1:4:8 type D-2 with 40mm graded crushed stone , 15 cm thick in foundation, brick work in CM 1:6 with sub class `B', old size bricks, rendering 15mm thick in CM 1:6 on exposed surfaces and 100mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45cm above the nearest road level. Note : (i) All out going feeders shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint.

aditya construction