ADDITION/ ALTERATIONTO BUILDING NO P-61,P/O 20 NOS WALL MOUNTED FAN AND 16 NOS OF PEDESTAL FAN IN BLDGE NO P-1 OF TECHNICAL AREA DEAL,P/O EARTHING ,P/O GRIL IN BLDG NO P-62 AND P-63 IN , INSTALLING OF 04 X AND P/O TOILET UNDER GE (I) RND DEHRADUN

Amount

Taking down door shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Dismantling of structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt or any treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 1000 m.all as directed

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for laying of cable etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

M&L for dry sand cushioning for UG cable in trenches including spreading levelling and hand paning and consolidating complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M & L for providing plain cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for cement concrete 1:2:4 type B-2, using 40 mm graded stone aggregate as in surface channel or drain complete all as specified and directed.

M & L for providing pre-cast cement concrete landing, cover slabs, chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:4 complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for DPC in horizontal or vertical surfaces 40mm thick in cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate complete all as specified and directed. Note : WPC will be measured and paid separately.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in fair finished surface of concrete complete all as specified and directed.

S & F of solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made wire gauzed PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panel will be of wire gauze. The wire gauze shall be wrapped on an additional square 8mm M.S Solid tube & this tube shall be welded to M.S tubes. The wire gauge shall be stretched to tighten firmly to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing etc.complete all as specified and directed

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S & F of 250 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

S & F of 125 mm long anodised aluminium D type handle, cast type complete all as specified and directed.

S & F of 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S & F floor door stopper double leg of aluminium alloy body of 140 mm length with aluminium base plate of size 50 mm x 40 mm complete all as specified and directed.

S & F hand rails, half ruond or other stock section or core for woodenhand rail starigt portion drilled and countersunk for balusters running bars for door balusters nosing to steps inculuding embeding in concrete and screwing etc. Wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets(for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.' and similar work conforming to Fe-290 Gde E-165. complete all as specified and directed.

S&F Stainless steel framed work of Grade- 304 of 01 mm thich such as grills, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred doors; ladders; framed balusters; walk ways; railings; framed work and similar works fixed through fastenars conforming to IS complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 8 mm dia and over up to and including 10 mm dia as in stirrups, spacer and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F of rolled mild steel sections as in main and cross beams, hip and jack rafter, purlins where connected to common rafters, running rails, guides for sliding doors fixed with angle cleat and other connecting plates conforming to Fe-290 (Gde E- 165) complete all as specified and directed.

S & F of mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexagonal or square nut, but length of bolt exc 10cm and n exc 15cm long and 11 to 15 mm dia of neck complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framed work and similar works complete all as specified and directed.

S & F of steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed and all as per CEBZ Drg No TD/088 dt 7 Jan 02

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F of Pre- painted galvatume aluminum zinc coating GI based corrugatged steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed . NOTE:- Corrugated shape of sheet shall be approved by GE

S & F of Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed . NOTE:- Corrugated shape of sheet shall be approved by GE

M & L for 100 mm thick cement concrete 1:4:8 type D-2, using 40 mm graded stone aggregate as in sub base of floor/hard standing complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in plinth protection laid to slop of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm thick joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

M&L Vitrified tiles coloured ceramic heavy duty deisigner tiles of size 400 mm X 400 mm X 12 mm checkered set , jointed and pointed in neat cement slurry in floors with grey cement complete all as specified and directed.Make : Jahnson Endura premium quality or equivalent

M & L for 18 to 20mm thick Granite stone slab (of any type/Colour ) Slabs machine cut in skirting/dado and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing over 15mm thick cement mortar 1:4 , on fair faces of brick work or concrete surfaces as backing for Granite stone slab complete all as specified and directed.

M&L Non - skid coloured ceremic tiles 7 to 8 mm thick (square/rectangular) area of each tilles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. Set & jointed in neat cement slurry and pointed in colored cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in cm (1:6) complete all as specified and directed

M&L Glazed ceremic tiles in vertical surface 350x250x7 mm /450x350x7 mm thick set & jointed in neat cement slurry and pointed in colored cement to match coloured tiles laid over and including 10 mm thick screed bed or bedding layer in cm (1:3) complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth (without using extra cement)complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extra cement)complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 a finished even and fair and mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. NOTE: - WPC SHALL BE MEASURED AND PAID SEPARATELY.

Supply only water proofing compound (Powder) complete all as specified.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes finished even and rough complete all as specified and directed.

S & F of 3 mm thick figured glass pin headed type and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparing newly plastered or previously untreated wall surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M & L for preparation of steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S & F of 500 Litre capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) of specifications as per MES Schedule 2009, Part – I and hoisted, fixed in position complete all as specified and directed.

S&F 15mm nominal bore of pipe in walls, and ceiling or laid in floors, jointing and testing galvanised mild steel water tubing “medium grade” with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all as specified and directed.

S&F 20 mm nominal bore of pipe in walls, and ceiling or laid in floors, jointing and testing galvanised mild steel water tubing “medium grade” with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all as specified and directed.

S&Fof bib taps, cast copper alloy with crutch or butterfly handle, screwed down, externally threaded having weight @ 0.40 Kg/Each, ISI marked with IS : 781, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

S&F of stop cock (valves), cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, externally threaded, having weight @ 0.40 Kg/Each, ISI certification marked with IS : 881, screwed both ends for iron pipe or for unions of 15mm bore complete all as specified and directed.

S & F of 20 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S & F 450 mm long PVC connection with two Nos. PTMT nuts internally threaded and PVC washer suitable for 15 mm bore pipe line complete all as specified and directed.

S & F of 100 mm dia grating doom of PTMT (minimum weight 25 gram) complete all as specified and directed.

S & F of 20 mm dia brass chromium plated tubular towel rail 'D' type 60 cm long between flanges, including one pair of fixing brackets complete all as specified and directed.

S & F of 15 mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD’ with long screwed shank and fly nuts, screwed for iron pipe complete all as specified and directed.

S&Fof vitreous china wash basin 550 x 400 mm size, coloured flat back or angle back, including brackets, CP waste coupling, PVC waste pipe etc and fixing of pillar taps including cutting for and pinning in the ends of brackets complete all as specified and directed.

S&F vitreous chiana wash down water closet (Pedested patern ) white incl fixing bolt, plastic water closet seat cover black/white closed pattern with flat bottom and cover and mild steel chromimum plated hinging device, fixed in repairs and incl 32mm dia waste pipe complete all as specified and directed

S & F vitreous china half stall type of flat back, , white with grating & unions for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and unions for discharge pipe and connecting complete all as specified and directed

S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to wall/floor complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F of 125 / 110 mm size PVC (SWR) gully trap, setting and jointing with solvent cement complete all as specified and directed.

M/L Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

S & F of 200 mm bore reinforced concrete pipe class NP-2 laid, jointed with collar in neat cement slurry complete all as specified and directed.

M & L for cement concrete 1:2:4, type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 200 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane with 10 years gurantee for water tightness complete all as specified and described as under:- (a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster. (b) One layer APP based polymeric membrance minimum weighing 3 Kg/ Sqm & minimum 3 mm thickness reinforced with polyster non woven fabric (wt not less than 150 gms/ sqm) land on primed surface by forced application complete all as specified and directed. Note :- Lap of 100 /150 mm and the over lap shall be sealed by flame. (c) A coat of hot blown bitumen grade 85/25 @ 1.2 Kg / Sqm shall be applied over polymeric membrane and blinded with clean dry sand at the rate of 0.05 Kg per Sqm as per manufacturer instruction . (e)M&L for 15 mm thick screed bed or bedding layer in CM 1:4 mixed with water proofing compound @ 3 % by weight of cement on top of membrane surfaces to recieving PCC tiles surface etc complete all as specified and directed. (f)S&F Precast machine pressed of grey cement concrete tiles of size 250 x 250 x 20 to 22 mm or 300 x 300 x 20 to 22 mm conforming to IS 1237 shall be laid over cement screed bed, the joints between the tiles will be 2 to 3 mm thick and filled with polymer base joint filler of approved quality (g)Supply only integral water proofing compound ISI marked. (h)Bitumastic gola, with 80/25 bitumen and coarse sand mixture, 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, concealed conduit wiring in walls and surface with GI saddles GI screws, rawal plugs in ceiling or roof if not possible including Tee, Junction boxes and provision of flush metal boxes, inner and outer plate suitable for modular switch, socket and fan regulator as per site requirement and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan point controlled by one Switch.

above for point wiring for 5 pin switch socket outlet, 5/6 Amps on independent board.omplete all as specified and directed. Note for item 77 to 78 here in before : (i) The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc. for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at RCC Columns/Beams/Ceilings shall be in surface conduit of suitable size fixed on surface with using PVC rawl plugs . (ii) Rate for modular metal flush boxes ,inner and outer plate with frames are deemed to be included in the quoted rate by contractor for above items. (iii) Fittings like Modular switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A'. (iv) The size of conduits shall be determined on permissible No. of runs of wires as specified in SSR Part-I (2009) clause 19.125 (B). However minimum size of conduit shall be 20mm dia (Medium grade (v) Make of cable : Finolex /Havells/ Poly cab as approved by GE.(vi) Make of PVC conduit & fittings : AKG / Asian /Plaza/Jindal /Avon/Finolex/National /Kalinga as approved by GE.

All as per item No 78 above for one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete all as specified and directed by Engr-In-Charge. Make of cable and conduit: Havells/ Polycab/Gloster

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FR multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories of 2x4 sqmm + 1x2.5 sqmm earth wire in conduit of suitable size complete all as specified and directed.

M&L for Sub main wiring with Two single core PVC insulated unsheathed cable 1100 volts grade, 10 Sqmm size with multistranded copper conductor, drawn in including suitable size of non metallic rigid PVC conduit including PVC insulated unsheathed 1x6 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly complete all as specified and directed.

M&L for Sub main wiring with Two single core PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in including suitable size of non metallic rigid PVC conduit including PVC insulated unsheathed 1x4 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly complete all as specified and directed.

S&F Modular switch 1 way 6 Amps, 1 module complete all as specified and directed.

S&F Modular switch 1 way 16 Amps, 1 module complete all as specified and directed.

S&F Socket, 6 Amps - 2/3 pin combined 2 module complete all as specified and directed.

S&F Socket 6 Amps/16 Amps - 2/3 pin combined 2 module complete all as specified and directed.

S&F Ceiling rose three teminal /PVC/ polycarbonate, insulated body complete all as specified and directed.

S & F Wall mounting fan 400 mm size complete all as specified and directed.Make- Havells/ Bajaj/Usha/Orient

S & F pedestal fan 400 mm size complete all as specified and directed.Make- Havells/ Bajaj/Usha/Orient

S&F MCB distribution board powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with SPN, 240 V, 8 ways AC all as complete all as specified and directed.. Make - Legrand cat ref no 507611 or equivalent in IndoAsian or ABB as approved.

S&F MCB distribution board SPN, 240 volts, 6 ways ,powder coated, CRCA steel sheet constructed as per IS : 8623-1 &3, degree of protection IP 42- IK-09 with glazed double door with two incoming and four outgoing terminals, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with following ratings & ways:- Note: (i) MCB’s /Isolators etc. shall be measured and paid for separately under appropriate item of Sch ‘A’ all as specified and directed by Engr-In-Charge. Make: L&T Cat Pt No. DBSPN006GD or equivalent in Legrand /Schneider as approved

S & F MCB SPN 240 volts 'C' Curve suitable for fixing in MCB DB of capacity 25 amps complete all as specified and directed by Engr-In-Charge.Make - L&T cat ref no BB20250C or equivalent in Legrand/Schneider as approved.

S & F MCB SP 240 volts 'C' Curve suitable for fixing in DB of capacity 6 to 32 Amps complete,all as specified and directed by Engr-In-Charge.Make- L&T cat ref no BB10060C/100C/160C/250C/320C or equivalent in Schneider/Legrand as approved.

S&F MCB SPN 240 volts 32 Amps, 'C' series 10 KA breaking capacity, including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-In-charge. Legrand Cat Pt No. 408617 or equivalent in IndoAsian or ABB

Supply and fix electric water heater storage type steel body with copper inner tank and heating element upto 2KW capacity 25 litre and BEE 5 star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etccomplete all as specified and directed.. Make: Bajaj/Havells/Crompton

S&F SPN enclouser with two pin and earth plug and socket complete with one single pole MCB 32 Amps, 240volts complete all as specified and directed.

Material & labour for maintenance free chemical earthing system using Isogel of M/S Tracel or equilent of Macmet/Erice chemical of 40 kg per earth pit for enhancing the soil coductivity and copper tube electrode of size 65 mm dia, 3 mtrs long having wall thickness 3 mm to be placed at the centre of a 53 mm dia bore vertically in groud. The tube shall be filed with isogel and the surroundings shall be filled tightly with mixture of isogel and soil. Use of 4 Nos copper rod of isogel and soil.The distance of rod to be from tube shall be 06 mtrs and at the angle of 90 drgree. These four rods to be conneced using 25X3 mm copper strip ,laying at least 60 cm below groud level and back filed with mixture of Isogel & soil. The connection of copper tube with copper strip should be done using Bi-matalic 'U' clamp. The tubes will be used as earth point and copper strip is to be extended upto test point upto maximum length of 7.5 mtrs. The test point shall be made of brass of size 120X120X5 mm in IP-55 enclouser,The copper strip must be laid through 40 mm dia GI medium grade pipe. The earth pit cover shall be made put of PVC material with locking arrangement etc complete, all as specified and directed by Engr-in-Chage.The work shall be carried out by the authorisede representative /agent of Idelac/Macmet/Erico in presence of Engr-in-Chage and the test result of earth resistance must be less than 1 Ohm, (Note :- 1.) The unit rate quoted by the contractor shall deemed to be included the drilling to any type of soil/hard,disintegrated rock etc it met during excavation by suitable earth mover machine, to achive the required depth of 03 mtrs below average groud level. 2) All jointing to be carried out by brazing in lieu of bolts & nut).

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (1991) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. NOTE : RCC pit cover shall be pre-cast of RCC (1:2;4) type B-1 80 mm thick reinforced with XPM weighting not less than 4 Kgs/Sqm in lieu of CI cover.

Supply and Fixing copper earth strip 32X6 mm burried in ground. complete all as specified and directed.

M&L for well burnt brick with sub class ‘B’ old size bricks for protection of cable complete all as specified and directed.

Disconnecting and taking out old existing unserviceable/ non- functional LT Cable and Supplying, laying, jointing and testing cable XLPE insulated IS 7098 (Part-I)-1988 marked, screened, PVC sheathed, armoured electric power cable (heavy duty) with aluminum conductor for working voltage upto and including 1100 Volts, cross sectional area of 16 Sqmm 4 core size of cables laid in trenches/fixed on pole/wall / passed through pipecomplete all as specified and directed. Make:Havells/GLOSTER/Polycab) (NOTE: Earth work, sand cushioning, pipe, clamps for holding cables and brick protection shall be measured and paid separately )

Disconnecting and taking out existing unserviceable light fitting of any description and S&F 10W LED Bollard light fitting (1 m in height) MOUNT-IP65 with excellent light output through its PMMA window ensuring maximum illumination aspect in surrounding,energy saving,enviromental friendly, long life aesthetically designed with symmetrical distribution,spun aluminium landscape luminaire with high power LEDs as light source complete accessories to be fixed on pole/pipes/gates including connecting the fitting to control switch at the bottom of the pole with using 2.5 Sqmm two single core PVC insulated and unsheathed copper conductor copper conductor cable complete all as specified and directed. (Make-Havells Cat No MOUNTBL10WLED857PSYMTOPMMAM or equivalent model of make Crompton/C&S).

Supply and fix aesthetically designed decorative hot dipped galvanized mild steel step pole with grey powder finish compatible for all Havells post top range, window plasma cut and duly chamfered opening window of 300x110 mm for terminal connections and mounting accessories. Window cover is fitted with allen screws to the pole complete with all accessories all as specified and directed by Engr-in-Charge.Make: Havells Cat Pt No.3MECOPOLE or equivalent in C&G / C&S

S&F LED mirror light fitting, 10 watts, 1000 lumens 6500K comprises of aluminium extruded channel, frosted diffuser, integrated electronic driver, IP 20 protection and all accessories pre- wired including connecting to mains complete all as specified and directed by Engr-In-Charge. Make- LCTLN-10-CDL of C&G or equivalent in Havells/Bajaj.c complete all as specified and directed.

S&F LED 20W complete batten fitting, efficacy: 100 lumen/watt with all as accessories complete all as specified and directed by Engr-In-Charge. Make: LCTLN-20-CDL or equivalent in Havells/Bajaj.

S&F bulkhead fitting with integrated LED bulk head fitting 600 lumens, 6000 K comprises of pressure die cast housing, acrylic diffuser and frame IP 65 protection, IK-07 etc including connection complete all as specified and directed by Engr-In-Charge.Make- LBHP-10-CDL of C&G or equivalent in Havells/Phillips as approved.

S&F exhaust fans made up of sturdy engineeirng plastic complete with louver shutter 230V, 50 Hz, RPM 1200, copper winding of sweep 250 mm alongwith making circular holes of suitable size suitable for mounting the exhaust fans and making the disturbed surfaces good complete all as speified and directed by Engr-In-Charge.Make: Havells/C&G/Bajaj

SHREYA INFRA DEVELOPER & CONSTRUCTION COMPANY

M/S WASEEM KHAN CONTRACTOR