Establishment of New Vulnerable Witness Deposition Centre (VWDC) at Taluka Court Jetpurpavi Ta. Jetpurpavi Dist. Chhotaudepur

Name of Work :- Establishment of New Vulnerable Witness Deposition Centre

(VWDC) at Taluka Court Jetpurpavi Ta. Jetpurpavi Dist. Chhotaudepur

BILL OF QUANTITIES

Memorandum showing item of works to be carried out.

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

1 wall panneling :- 34.56 Sqm 2875.00

Providing and fixing wooden wall panneling made of framing the

skeleton (plywood frame structure)with 18mm mm thick BWP grade

plywood for vertical and horizontal plywood (patti) back side cover

with 6mm thick BWP grade plywood for grooving as per design.Fixing

properly without any air gap and finishing with seletced 4 mm thick

natural veneer including pilishing with natural melamine .Before

installation,make hole/face plate for conduit pipes of

eletcrical/networking cables/Pipe Line with openable stud from

partition Including all materials and labour etc.complete as per detail

drawing and instruction of engineer-in charge.

2 Wooden partition :- 26.70 Sqm 3425.00

Providing & fixing Wooden partition having full height with whole

frame structure of Aluminium extruded alloy section with all sections

powder coated (50 micron) having overall partition thickness 80mm

(double skin) flush on both sides BWP 12 mm thick plywood

laminated with 4.0mm thick Natural veneer on both side of panelling

All surface finish with Natural malamine polish at all face of plywood

pannelling. and where necessary Decorative Glass in shutters,

decorative S.S. Handles and necessary superior quality hardware's

viz sliding channels, hinges including etc. inculsive of necessary

fixtures & fasteneres etc. complete as per drawings and designs

supplied by the department and existing sample in the instruction by

department and Engineer in charge.

3 Dias Table : 1.00 No. 22250.00

Providing and Arranging dias table having Top 40mm thick overall

made from 18mm thick MR garde plywood with 4mm thick veneer on

top and 0.8mm thick backing laminate and teakwood border having

size 25mm x 12mm with melamine polished finish. Top border to be

made from 75mm x 50mm indian teak wood.Top and both side 40mm

thick finish with 4mm thick veneer having melamine polish finish.

Appron to be made from 18mm thick MR grade plywood with 4mm

thick veneer having melamine polish finish with 0.8mm thick balancing

laminate. 8mm thick back painted glass on top to be provided. All

veneer surface to be melamine polish. Bookslot on the table shall be

provided as per the detail drawing including all materials and labour

etc. complete as per drawing and instruction of engineer-in-charge.

(with teakwood border with melamine polish)

Dias Table : size - 2100mm x 900mm x 800mm (H)

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

4 Providing and fixing Judges Court Room Dias Railing to be made 7.20 Sqm 4143.00

from best quality Special Indian Teak wood top horizontal rails of size

4"X3" and bottom horizontal rails of size 4"X1.5", vertical posts of size

3"X3" and end posts of size 4"X4" & vertical posts placed @ 9" c/c

and end posts placed at four places as shown in drawing with all

necessary materials all exposed wooden/plywood member including

sand papering, making, edges round with necessary hardware such

as ailen bolt, sheet, metal screw, nail, gluing material, sliding chanels,

fixtures, all exposed wooden members shall be semi glossy PU

polished including sand papering and making edges smooth with

necessary other fixtures and fastenings, including with bhutan bord of

red colour shade or approved shade 8mm to 10mm thick sheet fixec

inside the railing so that the vertcal post can be seen from front side

with making openable entry gate in railing to reach staff towards dias

as per drawings approved by judiciary department and instruction by

Engineer-in-charge.

5 Providing and Arranging dias chair having overall height of 1.52 mt 1.00 No. 9800.00

made from Indian teakwood having Back leg size 50mm x 50mm,

Back Support 75mm x 35mm size, handle 75mm x 30mm size, Back

Logo (National emblem) made from bronze metal of size 150mm x

30mm to be fixed on wooden back of size 225mm x 35mm Indian

teakwood frame work. All the wooden members to be moulded as per

the approved design and as diretced by Engineer in charge. Seat

having 80mm (3") thick 40 density foam to be fixed on 12mm thick MR

grade plywood and back having 50 mm (2") thick 40 density foam

bottom, back and seat foam both with high quality fabric (Basic Rate

Rs.400/Rmt) of approved shade. All wooden members finished by

melamine polish Including all materials and labours etc. complete as

per drawing and instruction of Engineer-in charge.

Dias Chair : Overall Size : [0.635 x 0.610 x 1.52 (H)]mt

(Armrest 0.63 Mtr)

6 Providing And Arranging table for judge chamber having overall 1.00 No. 25725.00

thickness of top 40mm (18+18+4mm) 18mm thick MR Grade plywood

and 4.00 mm thick veneer at top with melamine polish finish including

8mm thick back painted glass. Top to be made from 75mm x 50mm

Indian teak wood with half round moulded on long side with melamine

polish. Leg 50mm x 50mm x 1.6mm thick CRCA Square pipe and

supporting pipe 50mm x 25mm x 1.8mm finishing with epoxy powder

coated 50 micron with leveller. Appron having 18mm thick MR Grade

plywood with 4mm thick veneer having melamine polish finish. Drawer

Unit (450 x 550 x 600)mm having all Structure 18mm thick MR grade

plywood with veneer and teakwood border of specified size with

melamine polish finish. Drawers (3 No.) slides on Ebco make

telescopic channel with Godrej make lock with two keys and

necessary fixtures and fastening as approved with balancing laminate

inside 0.8mm thick of approved shade including all materials and

labours etc. complete as per drawing and instruction of engineer-in

charge. Side Unit to be provided saparetly.

Judges Chamber Table size : 2100mmx900mmx750mm (H)

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

7 Providing and Arranging side unit with top 40mm overall thickness 2.00 No. 8544.00

made from 18mm thick MR grade plywood with 4mm thick veneer on

top with melamine finished polish. Side and drawer made of 18mm

thick MR grade plywood with 4mm thick veneer with melamine

finished polish and inside 0.8mm thick balancing laminate of

approved shade. Teakwood border with melamine finished polish of

specified size to be provided all around the borders of plywood.

Drawer run on Ebco make telescopic channel with Godrej make lock

with Two keys and shutter fixed with auto hinges incld. all necessary

fixtures and fastening as approved and back of the unit with 6mm

thick MR grade playwood with 0.8 mm thick laminate of approved

shade with nylon bullet including all materials and labour etc.

complete as per drawing and instruction of Engineer-in charge

Side Unit size : 900mm x 450mm x 750mm (H)

8 Providing and Arranging book storage having top 18mm thick MR 3.00 No. 17645.00

grade plywood with 4mm thick veneer melamine polish finish with

0.8mm balancing laminate.Shelves made of 12mm thick clear float

glass with all edge polish. Side and shutter made of 18mm thick MR

grade plywood with 4mm thick veneer melamine polish finish with

8mm thick clear float glass and Lock and nylon bullet including all

necessary fixtures and fastenings as approved, including all materials

and labours etc. complete as per drawing and instruction of engineer-

in-charge (With teakwood border patti with melamine polish)

Glass Book Storage : 900mm x 450mm x 2100mm (H)

9 Providing, Arranging & fixing wooden coat stand made of Indian 2.00 No. 2375.00

teakwood, vertical member 65mm x 65mm size and bottom cross

design teakwood member of 75mm (H) x 37mm as per design with

melamine polish including moulding edges with teakwood single

hanger of standard size (75mm x 35mm) along with 2 nos. brass

hook, including all materials and labours etc. complete as per drawing

and instruction of engineer-in-charge.

Coat Stand: 650mm x 650mm x 1500mm (H)

10 Providing and arranging PREMIUM EXECUTIVE REVOLVING 2.00 No. 13500.00

CHAIR (High Back) Sigma chrome Base with Knee Tilt Synchro

Mechanism with Any Position back Lock, Seat & Back - Made from

High Density U - FOAM, Arms - Aluminium Die Casted with Cushion

Pad. Including all materials and labour etc. complete as per drawing

and instruction of engineer-in-charge. Size : max. Height : 1290mm to

Min. 1170mm, Seat : 530mm x 520mm, back 740mm x 500mm.

HOF / Godrej / Suzaco or instruction of engineer-in-charge.

11 Providing and Arranging Cushioned Seat & back, P.P. outer back 6.00 No. 4250.00

cover, P.P. arms, Single back lock, Push back mechanism, gas lift for

seat height adjustment, five prong Nylon base with twin wheel nylon

castor including all materials and labour etc. complete as per drawing

and instruction of engineer-in-charge. Size : Max. Hight 1020mm Min.

Height 930mm, Seat : 500mm x 460mm, Back : 500mm x 440mm.

Low Back Chair : HOF / Godrej / Suzaco or instruction of engineer-in-

12 Providing and Arranging fix chair having structure of CRCA M.S. pipe 16.00 No. 2600.00

20mm dia. and 16 guage with 50 micron powder coated of approved

seat and back 40 density PU foam covered with fabric of approved

shade and texture with one year replacement warranty. Wooden

armrest to be provided as per approved design. Complete chair

should be in suitable shape including all materials and labours etc.

complete as per drawing and instruction of engineer-in-charge.

HOF or Equivalent make

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

13 Providing and Arranging three seater wooden sofa made from Indian 3.00 No. 15000.00

teak wood with melamine polish. Seat made from 100mm thick

density foam with 25mm thick supersoft HD covered for softness. seat

to be kept on high density nylon elastic belt inside Framing size 50mm

x 37mm support armrest, legs and outer frame having size 80mm x

37mm with inner brace between armrest and seat frame having size

25mm x 50mm as showing the photographs. Back 80mm thick

density foam with 12mm thick supersoft HD covered for softness.

Seat and back covered with high quality fabric approved shade and

wooden armrest Including all materials, hardwares and labours etc.

complete as per drawing / photographs & detail and as directed by

Engineer-in-charge.

HOF or Equivalent make

14 Providing and arranging single seater wooden sofa made from Indian 3.00 No. 12500.00

teak wood with melamine polish. Seat made from 100mm thick

density foam with 25mm supersoft HD covered for softness. Seat to

be kept on high density nylon elastic belt inside Framing 50mm x

37mm support. Outer frame 80mm x 37mm. Back made from 80mm

thick 40 density foam with 12mm thick supersoft HD covered for

softness. Seat and back covered with high quality fabric approved

shade and wooden armrest Including all materials and labours etc.

complete as per drawing / photographs & detail and directed by

Engineer-in-charge.

HOF or Equivalent make

15 Providing and Arranging tea table made from 37mm x 37mm size 3.00 No. 3801.00

Indian teakwood leg and top frame made from 37mmx 75mm Indian

teakwood having 18mm thick Ply and 4mm thick Veneer with

melamine polish and 0.8mm thick balancing laminate at bottom for

shelf made with surrounding Indian teakwood frame of size 37mm x

12mm. The top having 12mm thick frosted glass with edge finish to be

placed properly in groove made. Surface to be finished with melamine

polish including all materials and labours etc. complete as per

drawing and instruction of engineer-in-charge.

Tea Table : size - 900mm x 600mm x 450mm

16 Providing and Arranging Cabinet made from 18mm thick MR grade 8.00 No. 6050.00

Plywood box with one drawer unit having size 260mm x 500mm x

150mm fixed on Ebco made telescopic channel with godrej make lock

with two keys set and one shutter having SS hinges (Auto 16 deg.),

handles and Indian teakwood border patty with melamine polish.

Cabinet finish with 4mm thick approved veneer and 0.8mm thick

balancing laminate to be provided. On top of the storage 18mm thick

approved mirror polished granite with rounding edge moulding shall

be provided including necessary fixtures, fastening including all

materials and labours etc. complete as per drawing and instruction of

Engineer-in charge.

Storage Unit : size - 325mm x 525mm x 750mm (H)

17 Providing and Arranging table having 40mm thick top overall 3.00 No. 18995.00

thickness made from 18mm thick MR grade plywood, top and side

finish with 4mm thick veneer. both side (inside and outside) to be

veneered and top back side 0.8mm balancing laminate including teak

wood border patty of size 40mm x 12mm. Whole table having MS

CRCA Pipe framing of 50mm x 50mm x 1.6mm size and 50mm x

25mm x 1.8mm size finished with epoxy powder coated of 50 micron

thickness as per drawing / photograph and details including all

materials and labour etc. complete as per drawing and instruction of

engineer-in-charge. (with teakwood border with melamine polish)

Advocate Table : size - 2400mm x 900mm x 750mm

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

18 Providing and Arranging benches (bakada) made from 50mm x 25mm 4.00 No. 21560.00

indian Teakwood patti with smooth edge moulding 5 Nos. each on

seat and back as per design. under structure made from CRC M.S.

50mm x 50mm x 1.6mm pipe 16 Guage and 50mm x 12mm flat for

base support with 50 micron powder coating frame. All wooden

member to be melamine polish including all materials and labour etc.

complete as per drawing and instruction of engineer-in-charge. Over

all size : 2250mm L, Seat : 450mm W, back : 400mm.

5 Seater WOODEN Bench : size - 2250mm x 450mm x 750mm (H)

19 supplying Imported S.S. Three Saters Peforated benches with using 6.00 No. 9500.00

S.S. Perforated Sheet in Sheet And Bach with S.S. Pipe In frame and

support with 25mm Cusion with black rexien on both sheat on back

portion of the bench with necesaary other fixtures and fastening etc

comp or as direcdet by Engineer incharge

20 Providing and fixing AJANTA make wall clock of the desired shape 6.00 No. 871.00

and design as seletced by Engineer-in-charge.

21 Providing and Arranging S.S. Nickle chrome plated Dustbin having 12.00 No. 900.00

254mm dia. & 356mm height with perforated S.S. sheet having

thickness 18G including all necessary fixture, fastners, fittings,

labours, materials, machinary etc. complete as seletced and diretced

by Engineer-in-charge.

S.S.DUSTBIN- SINTEX MAKE:SSHPB02-01

22 Providing and Arranging of 100 Litre capacity LLDPE solid waste bin 2.00 No. 2440.00

having size at top 500mm & bottom 350mm square, height 900mm

having standard weight as per the manufacturer's specification of

unit including all necessary fixture, fastners, fittings, labour, material,

machinary etc. complete as seletced and diretced by Engineer-in-

Dustbin Big 100 lit : SINTEX MAKE - no: GBR 10-01

23 Providing, fixing & Arranging boltless shelves (1 Main) having load 3.00 No. 5782.00

bearing members made of high strength CR/HR steel confirming to

IS 5986 :2002 / IS 2062 : 2006 by using steel confirming to is 5986-

Fe 410 with minimum yield strength of 255 MPa The fasterners of

grade 8.8 with galvanized finish including powder coating with

thoroughly anti rust treatment the upright component of T- shaped

oxford blue finish of G 50 type having profile width of 50mm. single

piece of having Min. yield strength of 250Mpa shelves of 14 based

zinc coated finish having size of 1300 mm x 450 mm x32mm mounted

on shelf clips clips having profile setcion of (24 x 8 x 35)mm &

bends with galvanized surface finish stability beam of setcion 65mm

x 30mm with galvanized surface finish back tie of 5mm dia. of tie rod,

turn buckle of 90mm with galvanized surface finish all the

components having powder coating with thoroughly anti rust

treatment including all necessary fixture, fastners, fittings, labour

material machinary etc. complete as seletced and diretced by

Engineer-in-charge.

Boltless Rack :Godrej / HOF or Equivalent MAKE: REC-6C

24 Providing & fixing notice board having 9mm soft board as a core 4.00 No. 4125.00

material 1mm laminate sheet as back material & surface of 1.0 mm

felt cloths, having profile of heavy alluminium fluted anodized profile

10 to 12 micron of 18mm to 25mm thick board ‘C’ channel & corner is

made up of molded virgin ABS grey colour hanging vertical &

horizontal hanging facility as per sletced colour & size including all

necessary fixture, fastners, fittings , labour, material, machinary etc.

complete as seletced and diretced by Engineer-in-charge. Approved

Make : alkosign / altop / signmark DELUX SERIES.

Notice Board : size - 900 mm x 1200 mm

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

25 Providing and fixing Alkosign make powder coated M.S. complain 2.00 No. 1625.00

box having overall size of 302mm x 355mm x 102mm with lock and

Complain Box : Alkosign Make size- 302mm x 110mm x 355mm(H)

26 Providing and Arranging arylic work top with 10mm clear imported 2.00 No. 3560.00

Acrylic sheet with two brass rods with height adjustable of overall size

580mm x 400mm etc. complete as diretced by engineer-in-charge.

Approved Make: alkosign / OKay/ signmark.

27 Providing & Arranging ladder made from 67mm x 31mm x 3.15mm 1.00 No. 14590.00

HINDALCO HE-30 high tensile alluminium 'C' setcion having top size

455mm x 250mm (18" x 10") with steps in bottom square setcion &

overall width of ladder is 400mm with rubber shoes at the bottom of

ladder. Height shall be 15 feet.

28 Providing and fixing 'SATYAMEVA JAYATE' inscription in officer 2.00 No. 8450.00

chamber, properly fixed on a wooden panel with wooden frame etc.

complete as directed by engineer in charge

29 Providing and Fixing Impulse Blackout Roller Blinds with fabric of 91.51 Sqm 1850.00

0.53mm thickness and Top channel of non-rusting aluminium alloy

with 1.25mm thickness and bottom channel of 1.50mm thickness &

21mm diameter. Tilt channel of ABS plastic with 1.50mm polyster cord

with 4.50mm balls with stop lock arrangement including all necessary

fixture, fastners, fittings, labour, material, machinary etc. complete as

seletced and diretced by Engineer-in-charge.

Roller Blinds : MARVEL or Equivalent MAKE

30 Providing and fixing sign board made of acrylic sheet and fixing on 26.00 No. 236.00

door wall in first or second alphabet as instructed in radium material

including all materials and labour etc. complete as per detail drawing

and instruction of engineer-in-charge.

Acrylic Name Board : 12" x 5 "

31 Providing and fixing DORMA MAKE DOOR CLOSURE MODEL NO 12.00 No. 859.00

TS 77 std. at desired location as instructed Including all materials and

labour etc. complete as per detail drawing and instruction of engineer-

DOOR CLOSURE : DORMA MAKE : TS

32 Providing & fixing steel back key cabinet for 40 keys having overall 2.00 No. 1530.00

size of 520mm(W) x 500mm(H) x 50mm(D) of 13mm Anodised

alluminium single & double frames. Back steel sheet is gay colour

powder coated with 40 nos. punched holes for key chain holding

including plastic key chain with steel wire rings numbered 1 to

having corners of ABS in grey colour. Cabinet should be with 1 No. of

lock with 2 Nos. of keys & top cover in 3mm thick acrylic sheet

including all necessary fixture, fastners, fittings , labour, material,

machinary etc. complete as seletced and diretced by Engineer-in-

Key Cabinet 40 keys : ALKOSIGN MAKE

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

33 Providing And Arranging table top made of 36mm thick BWR grade 4.00 No. 31950.00

plywood with nail curvica Laminate finish.Leg & frame to be made

from 50 x 50 x 1.6mm size & 50mm x 25mm x 1.8mm size CRC

Square pipe powder coated 50 micron finish with levlar Appron

mm thick MR grade plywood with Laminate finish.Drawer Unit-450 x

550 x 600 mm made of All Structure 18 mm thick MR grade plywood

with Laminate finish. Drawer run on Ebco make telescopic channel

with Godrej/Ebco make lock inside 0.8mm thick laminate of approved

shade. Side Table : side table top made of 36mm thick MR grade

plywood with nail curvica Laminate finish. side & shutter made of

mm thick MR grade plywood with Laminate finish Including all

materials and labour etc.Complete as per drawing and instruction of

engineer-in charge.

Table Unit Size :- 1500 mm x 600 mm x 750 mm(H)

Drawer Unit Size :- 450mmX550mmX600mm(H)

Storage Unit :- 900mmX450mmX750mm(H)

34 Providing and Arranging Mobile Drawer Unit made of all structure 4.00 No. 7770.00

18mm thick MR grade plywood with 4mm thick veneer melamine

polish finish. Drawer run on Ebco make telescopic channel with

Godrej/Ebco make lock & inside 0.8mm thick laminate as balancing

laminate as per approved shade with one Drawer and One Shutter

with teakwood border patti melamine polish including all materials and

labour etc. complete as per drawing and instruction of engineer-in-

Mobile Drawer Unit-Size:1500mm x 600mm 750 mm

35 Providing and Arranging Two side argument small desk made of 4.00 No. 2706.00

18mm thick MR grade plywood having Desk Size : 600mm x 450mm

& front height 450mm back height 400mm (i.e. slanting position) with

wooden teakwood patti for frame & to hold paper and pen. Top and

side 18mm thick finish with 4mm thick veneer both side. All veneer &

teakwood surface to be melamine polish.

36 Providing and Fixing 6mm Unitex make Loop Pile Carpet Roll Base 90.16 Sqm 1850.00

Form.Made out of 100% BCF Polypropylene pile fibre with solution

Dyed Yarn width(mts)3.66 & Roll Length approx 30(mts) with 6mm

Thick. The Carpet should have 650 to 850 gms/m2 Tufted Pile Weight

with 165,900tufts/m2 Density. Bonding Strength should be 30 Newton

and Tuft withdrawal strength 20 Newton of approved Colour , product

model and shade by Engineer in Charge including all necessary

fitiings,labour material and man power for the desired workmanship

Floor Carpet : UNITEX MAKE 6 mm thick

37 Suplying steel cupboard of size 916mm(W)x 486mm(D) x 1980mm(H) 6.00 No. 12980.00

having shelf made of 0.7mm thick CRCA & 0.8mm thick high yield

strength CRCA for doors & back 0.9 mm thick CRCA for all other

components.Grade of CRCA would be ‘D’ grade confirming to IS

:513 having three way locking mechanism with shooting bolt shelf with

adjustable shelf mounting with uniformly distributed load capacity as

per shelf is 40 kg. maximum inclusive 4 nos. of adjustable full shelf &

box file A4 size ( 85mmW x 345mmH x 285mmD ) can be stored

vertically on three shelves & clear space above fourth shelf is

mm. with necessary epoxy powder coating with 50 microns thickness

including all necessary fixture, fastners, fittings , labour material

machinary etc complete as selected and directed by Engineer

Approved Make: Godrej/ Herman Miller/ Haworth/ Knoll

38 Providing & fixing FRP mural of 'Statue of Justice' having Copper 1.00 No. 135670.00

Finish as approved and fixing it with appropriate S.S/brass screw and

joining with adequate sealant etc. complete as per direction of the

Engineer in Charge

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

39 Suplying Computer table Table 6.00 No. 10580.00

(1200mmx750mmx750mm) to be made from selected best quality

Special Indian Teak wood top, side and legs with 12mm thick Glass

on top, 18mm Plywood ISI brand with decorative Teakwood finish

Vineer Top, side and front using, all necessary materials all exposed

wooden/plywood member including sand papering, making, edges

round with necessary hardware such as ailen bolt, sheet, metal

screw, nail, gluing material, sliding chanels, fixtures, all exposed

wooden members shall be semi glossy PU polished including sand

papering and making edges smooth with necessary other fixtures and

fastenings etc.complete as per drawings approved by judiciary

department and instruction by Engineer in Charge.

40 Wooden visitor chairs. Providing and Supplying Wooden visitor chairs 12.00 No. 5800.00

with indian teak wood frame size 75 x 75 mm support and legs with

12mm thick W.P plywood in seat portion and 6mm thick W.P plywood

in back portion with 75mm thick 40 density U foam in seat and 50mm

thick U foam in back portion with tapestry cover with necessary other

materials inclusive of melamine polishing etc. complete as per

engineer in charge.

41 Dismentling doors, windows, ventilators etc. (wood or steel) shutters 9.00 Each 196.66

including chowkhats architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift.(i) Not exceeding

42 DOORS IN VENEER :- Providing and fixing 35mm flush door 25.32 Sqm 5830.00

laminated with 4.0mm thick Natural veneer on both side, All surface

finish with Natural malamine polish at all face of Door with decorative

S.S. Handles, mortise lock/aldrop, BTC patti, 4 Hinges including etc.

design as per drawing and instruction by department and Engineer in

43 Providing and fixing Door of factory made & stamped I.S 12823 9.84 Sqm 3622.87

grade one, type one 35 mm thick solid core , melamine faced , three

layered resin, flushed door, having decorative lamination on both side

including 30 cm long Stainless Steel pipe handle on both side SS

ASIS 304 Grade, SS Stopper 20 CM,SS Aldrop 30CM both side, SS

Hinges 3No`s in each shutter & fixtures & fastenings as directed by

Engineer in Charge, etc. complete.

44 Removing dry or oil bound distemper by a washing and scraping and 175.51 Sqm 11.82

sand papering the wall surface smooth including necessary repairs to

scratches complete.

45 Applying two coats of Birla or Asian acrylic lappy (putty) and two coats 175.51 Sqm 40.59

of primer of approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the surface free

from mortar dropping and other foreign matter and sand papered

46 Distempering (two coats) with Oil bound distemper of approved bradn 175.51 Sqm 77.30

and manufacture on wall surface to give an even brushng the surface

free from mortar droppings and other foreign matter and sand

prepered smooth extra over item every sub sequent coat of wall

painting with Oil bound distemper of approved brand.

It. Item of Work Qty. Unit Rate in Total

No. Figures Amount

47 Providing and fixing eco-friendly light weight calcium silicate false 36.75 Sqm 1674.15

ceiling tiles having Tegular edge & 15 mm Thick Densified edges on

the Tile Periphery for Extra Strength The Light weight calcium silicate

ceiling tiles shall have, light reflection 85% non-combustible as per

B.S. 476 part IV, 100% humidity resistance and also having thermal

conductivity0.043° w/m KC.for the best thermal Insulation . The Light

weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC

value of 0.75 NRC or equivalent of size 595 X 595 mm to be laid on

true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including

both side) consisting of main ‘T’ runner suitably spaced at joints to get

required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size

24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm

along spaced between main ‘T’ at 600mm centre to centre to form

agrid of 1200X600mm and secondary cross T’ of length 600mm and

size 24x28mm made of 0.30 mm thick (Minimum) sheet to be

interlocked at middle of the 1200X600mm panel to form grid of

i.e. Rs. Twenty lakh Twenty Seven thousand Six Hundred Eighty Rupees and Seventy Four paise only.

I/We am/are willing to carry out the work @ ______________ % above/below percent

(Should be written in figures and words) of the estimated rate mentioned above. Amount of

my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and found

Deputy Executive

Sr. Divisional Engineer

Account Officer Sr. Divisional Account Officer Executive Engineer

Bodeli (R & B) Sub Division Chhotaudepur (R & B) Division, Chhotaudepur (R & B) Division,

Bodeli Chhotaudepur Chhotaudepur