Special repairs to bldg No HT 04 family ward of MH Ambala under GE South Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS) Taking down cement or cement lime plaster, of any description, on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, and removal of debries to distance exc 50 mtr and n exc 100 mtr complete all as specified and as directed.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without extra cement all as specified and as directed.

Material and labour for rendering, 15 mm thick, in cement mortar 1:4, mixed with water proofing compound @ 2% by weight of cement or as per manufacturer’s instructions, on fair faces of brick work or concrete surfaces of any description finished even and smooth without using extra cement complete all as specified and as directed. Note: Supply only integral water proofing shall be measured and paid separately.

Material and labour for rendering, 10 mm thick, in cement mortar 1:3, on surfaces of ceiling, finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour for preperation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed.

Material and labour for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and as directed.

Material and labour for preperation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and as directed.

Material and labour for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of cement base paint including preparation of surfaces complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

Material and labour for solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame over and including 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of wall plugs nails etc for fixing on to wall to make PVC Frame, all as per standard drawing, complete all as per specifications and as directed.

Supply and fix GI Metal Suspended Ceiling System at all heights of Perforated with Fleece 600x600x0.5mm TEGULAR EDGE TILES in global white Powder Coated with 60-70 Micron front coating laid on 24mm wide Tee grid – strong section flanges colour white having stitching on the Main Runner, 600 mm and 600 mm Cross Tees with web height of 26mm. The tiles should have Humidity Resistance (RH) of 100%, with Light Reflection of 62%. The main runner spaced at 600 mm max (centre to centre) securely fixed to the structural soffit . Hangers (GI wire of 4 mm dia) to be fixed by approved roof plug, level adjusters and screws etc at 600x600 intervals.The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 600mm long cross tees to be interlocked between main runners to form 600 x 600 mm with grid module(24X38X0.3mm).Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 600 mm cross tees. Perimeter trim to be wall angles of size 3000x22x22mm, secured to walls at 450mm max (centre to centre), including PVC clips to hod the ceiling tile including taking down of old ceiling of any descriptions as existing at site and removal complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing selviceable tiles to store and removal of debries to distance exc 50 mtr and n exc 100 mtr complete all as specified and as directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular), area of each tile exceeding 0.18 sqm and not exceeding 0.38 sqm and 7 to 8 mm thick, laid in floor over and including cement screed bed 15mm thick in cement mortar (1:4) and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface complete all as specified and directed.

Description all as per item No. 14.00 above but tiles laid in skirting/dado over and including cement rendering 10mm thick in cement mortar (1:3) and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface complete all as specified and directed.

Material and labour for premium quality, joint free, printed glazed coloured ceramic tiles of size 300 x 450 x 7mm thick on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from frame) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish including removal of serviceable/unserviceable material from site complete all as specified and directed.

Supply and fixing of pressed steel frames for doors of size 125x60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm FI, 25mm long, 6 Nos in each chowkhat, necessary lugs, 4 Nos 100 mm butt hinges medium weight, cold rolled, welded for each frame, lock strike plate, including sanding, tarring backs of chowkhats, PCC 1:3:6 type C-0 filling in frame and for holdfast, 2 Nos 12 mm dia tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.

Material and labour for factory made second class HW 35mm thick plain framed panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply of 12mm veneered particle board with commercial veneering on both face. The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and directed.

Material and labour for second class hard wood glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, elc.;sizesof me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and directed.

Supply and fixing of aluminium anodised, 200mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing of stainless steel butt hinges, medium weight with mild steel hinge pin, bright polished and fixed, type B-11, of size 100mm complete all as specified and directed.

Supply and fixing of 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Material and labour for plain cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregates, as in hold fasts including necassary form work complete all as specified and directed.

Supply and fixing of aluminium handles, 150mm, cast type, anodised complete all as specified and as directed.

Supply and fixing of floor door stopper of aiuminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with overall length of cover plate of 150mm complete all as specified and as directed.

Supply and fixing of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of approved colour synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of old steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying one coat of approved colour synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, complete all as specified and as directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc, including stacking of servisable bricks and removal of debries to distance exc 50 mtr and n exc 100 mtr complete all as specified and as directed.

Material and labour for brickwork, with subclass 'B' bricks, straight or curved on plan to any radius, exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed.

NON ACCESSIBLE ROOF TREATEMENTS : APP TREATMENT WITH BRICK/PCC TILES:-Material and labour for providing and laying 3mm thick APP(atactic polypropylene polymer) modified prefabricated, five layer, weight not less than 3.60 kg/Sqm, water proofing membrane, black finish, reinforced with non woven polyster matt, make as approved, with termofusable finish laid by force aopplication after applying a coat bitumious primer @ 0.40 ltr/ Sqm by the same membrane manufacturer of density 0.87 to 0.89 kg/ltr at 25' C temprature and viscosity 70-160 cps over the primer coat with overlap of 100mm at the sides and 150mm at the end, ceiling including a tack coat of hot blown bitumen 85/25 @ 1.2Kg per Sqm below APP and two coats of water proofing paint with aluminium finish on top of laid APP surfaces including preparation of surface over and including 50mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in levelling course etc., including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust,etc. and brushing the surface with neat cement slurry @ 3.0kg of cement per sq. metrecomplete all as specified and directed. The vital physical and chemical parameters of the membrane shall be as under :- (i) The layer membrane shall be laid using butane gas torch and sealing all joints etc after preparing the surface complete as per standard practice all as per manufacture's instuctions (ii) Joint strength in logitudinal and transverse direction at 23'Cat 650/450 N/5 cms (iii) Tear strength in logitudinal and transverse 150'C when tested in accordance with ASTM (d-5147) (iv) The laying of membrane shall be got down through the authorised applicator of manufactures of membrane only. Note:- The contractor will carry out ponding test after application of APP treatment before claiming payment.

Supply and fixing in repairs of MS powder coated conduit 1.6mm thick decorative curtain rod, 25mm dia, and fixing with decorative brackets 2 Nos for each cut length, stop rollers and finials at the end for each length complete all as specified and directed.

Supply and fixing in replacement, stainless steel sink with draining board, made out of 1mm thick sheet of Grade SS 304 for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx330mmx160mm including waste pipe and waste fittings, brass, chromium plated for glazed ware sinks, basins etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Supply and fixing of water storage tank of 1000 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fixing in repair of GI tubing, ISI Marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing in repair of GI tubing, ISI Marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing in repairs stop valves, 15mm bore, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Note : Weight of stop cock/angle cock shall not be less than 0.575 Kg

Supply and fixing in repairs pillar taps, 15mm bore, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repairs CP bib taps,15mm bore, long body, cast copper alloy with crutch or butterfly handle, screwed down, high pressure, screwed for iron pipe or for brass ferrule or union and fixed complete all as specified and as directed. Note : Weight of bib tap shall not be less than 0.575 Kg

SCHEDULE A PART II (E/M WORKS) Taking down carefully any type of point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets, tube light fittings with all accessories etc., and/or drawing out from existing conduit/batten and removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLS-H, 1100 volts, ISI marked, PVC insulated and unsheathed stranded cable drawn through and including non metallic, medium grade PVC concealed conduit not less than 25.00mm to 32.00mm dia and its fittings, including cutting chasing on wall/ceiling, including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes, ISI marked, including 1.5 sqmm single core PVC insulated and unsheathed FRLS-H cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with and including MS flush boxes of 2 to 18 modules with inner and outer cover plates, confirming to IS 5139 of 1969 and IS 14772 of 2000 for fixing modular switch sockets for one light point (For flourescent Tube/ LH, Bldg Security light, Mirror light)/fan point/bell point controlled by one one way switch complete all as specified and as directed. Notes :- (i) Switch, socket, ceiling rose, lamp holder, bell, bell push and fan regulators to be measured and paid for separately. The quoted rates are deemed to be included for providing cover plates and MS flush boxes as required at site. (ii) PVC Conduit conforming to IS 9537 part I & III. (iii) All chases will be cut by chase cutter only and surfaces shall be make good as per existing surfaces. (iv) The concealed conduits and MS boxes as fixed against new point wiring, shall be verified by Engineer-in-Charge before making good the surfaces by plastering and other finishes.

Description all as per Srl item No. 44.00 here in before but for one 3 pin socket outlet point 5 Amp on same board.

Description all as per Srl item No. 44.00 here in before but for one 3 pin socket outlet point 5 Amp on Independent board.

Description all as per Srl item No. 44.00 here in before but for bell point controlled by one bell push.

Description all as per serial item No. 44.00 above, but for one socket point 15 and 5 Amps (independent), with 2.5 Sqmm PVC, FRLS-H, unsheathed, multistranded cable, 1100 volts grade, ISI marked, including 2.5 Sq mm size, green colour, PVC insulated FRLS-H, continuous copper earth wire and connected to common earth dolly complete all as specified and as directed. Note- Switch, Socket shall be measured and paid separately and Steel junction boxes shall be used wherever junction boxes are to be fitted.

Material and labour for point wiring in existing concealed conduit using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLS-H, 1100 volts, ISI marked, PVC insulated and unsheathed stranded cable drawn through existing concealed conduit, including 1.5 sqmm single core PVC insulated and unsheathed FRLS-H cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with and including MS flush boxes of 2 to 18 modules with inner and outer cover plates, confirming to IS 5139 of 1969 and IS 14772 of 2000 for fixing modular switch sockets, for one light/fan point controlled by one switch complete all as specified and as directed. Notes :- (i) Switch, socket, ceiling rose, lamp holder, bell, bell push and fan regulators to be measured and paid for separately. The quoted rates are deemed to be included for providing cover plates and MS flush boxes as required at site. (ii) The disturbed surfaces of wall shall be made good as per existing.

Description all as per Srl item No. 49.00 here in before but for one 3 pin socket outlet point 5 Amp on same board.

Description all as per Srl item No. 49.00 here in before but for one 3 pin socket outlet point 5 Amp on Independent board.

Description all as per serial item No. 49.00 above, but for one socket point 15 and 5 Amps (independent), with 2.5 Sqmm PVC, FRLS-H, unsheathed, multistranded cable, 1100 volts grade, ISI marked, including 2.5 Sq mm size, green colour, PVC insulated FRLS-H, continuous copper earth wire and connected to common earth dolly complete all as specified and as directed. Note- Switch, Socket shall be measured and paid separately and Steel junction boxes shall be used wherever junction boxes are to be fitted.

Supply and fixing of switch modular, 6 Amps, one way, one module, single pole, 230 volts, 50 Hz complete all as specified and directed.

Supply and fixing of switch modular, 15 Amps,one way, one module,single pole, 230 volt complete AC supply all as specified and directed.

Supply and fixing of socket outlet modular, 2/3 pin combined, 6 amps, one way, 2 module, single pole, 230 volts complete all as specified and directed.

Supply and fixing of socket outlet modular, 2/3 pin combined,16 amps, one way, 2 module, single pole, 230 volts complete all as specified and directed.

Supply and fixing of fan regulator/dimmer stepped type, 120 watt, 1/2 module, 230 volts, 50 Hz AC supply, suitable for ceiling fan, any type/make/sweep complete all as specified and as directed.

Supply and fixing of modular bell push, 6 Amps, one module, single phase, 230 volts, ISI marked complete all as specified and as directed.

Supply and fixing of bell buzzer, ding dong type, AC, 230 volts, single pole complete all as specified and as directed.

Supply and fixing of ceiling rose surface bakelite 65x50mm, three terminals complete all as specified and as directed.

Supply and fixing of lamp holder, PVC/Polycarbonate type, with back plate suitable for batten fittings complete all as specified and as directed.

Supply and fixing of retrofit LED lamp/Bulb of 12 watt B-22 base complete all as specified and directed.

Supply and fixing in replacement channel for fixing of LED tube rod, made of aluminium housing body in CRCA sheet, suitable for 18/20 watt LED tube light, high efficient, AC, 220-240 Volts, 50 Hz, with built in electronic drivers having THD < 10%, connecting up with core 1.5 sq mm flexible copper conductor cable from ceiling rose to connector block of light fitting including disconnecting and taking down existing light fitting and removal complete all as specified and directed.

Supply and fixing in replacement T-8 LED tube rod 1x18/20 watts, AC, 220-240 Volts, 50 Hz, high efficient T8 with aluminium extrusion heat sink for optimum performance with high lumen efficiency including taking down of old tube rod complete all as specified and directed.

Dismantling and taking out old tube light/LED fittings from wall/ceiling and keeping in safe custody and refixing the same after cleaning and minor repair required for functional and connecting with new copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to light fitting complete all as specified and as directed.

Supply and fixing of decorative, surface mounted, mirror light, LED tube light wall mounting light fitting, high efficient PMMA diffuser, aluminium housing in CRCA body suitable for and including 10 watt LED tube, high efficient, AC 220-240 volts,50 Hz, and compact and energy efficient, epoxy powder coated, CRCA sheet, connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light fitting including disconnecting and taking down of existing old unserviceable light fitting of any description and removal from site complete all as specified and directed.

Supplying and fixing of LED bulk head light fitting with and including 10 watt LED lamp and holder complying IP66 ingress protection and inpact resistance of IK09 long life, 50000 burning hours, including connecting up using three core, twisted flexible copper conductor cable of suitable size from ceiling rose to connector of light and disconnecting and taking down of existing light fitting and of any description removal complete all as specified and directed .

Supply and fixing of LED security light luminaire 30 watt, 230 volts, 50 Hz, made up of die cast aluminum housing with black epoxy powder coating with cover heat resistant glass, safety input voltage range 170 to 270 Volts, IP66 protection, including service brackets of GI pipe 25mm bore, light grade, of length 1.60 metre, bent to required shape, fixed with MS clamps of size 40 x 6mm flat iron strip, 150mm long and 4 Nos.8mm dia stainless steel bolts and nuts and washers and suitable reducer for connecting to GI pipe as required at site and making all required electrical connections using 3 core copper flexible cable from terminal box to ceiling rose including disconnecting and taking down of old fitting with bracket as existing complete all as specified and as directed.

Supply and fixing of post lamp lantern, LED 30 watt, made up of die cast aluminum spigot, with high efficient LED light with poly carbonate diffuser, complete with high efficient 30 watt LED lamp and accessories internally prewired complete including connecting up using three core, twisted flexible copper conductor cable of 1.5 sq mm size from ceiling rose to connector of light and disconnecting and taking down of existing light fitting of any description and removal complete all as specified and directed.

Supplying and fixing in repair surface mounting round type LED, 12 watt, wall mounted light adjustable, with high efficiency, clear diffuser, IP 20 protection including connecting up using three core, twisted flexible copper conductor cable of 1.5 sq mm size from ceiling rose to connector of light and disconnecting and taking down of existing light fitting of any description and removal complete all as specified and directed.

Supplying and fixing of 1100 volts grade, heavy duty cable, PVC insulated, aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular, 16 sq mm complete all as specified and directed.

Supply and fixing of sheet metal enclosure, single pole with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps, 'C' Curve, 240 volts complete all as specified and directed.

Material and labour for sub main wiring with four single core, 6 sqmm, FRLS-H, 1100 volts grade, ISI marked, with multistranded, PVC insulated unsheathed copper conductor cable, drawn in and including rigid non metallic PVC conduit , medium grade, not less than 32 mm dia, ISI marked for housing cables, concealed in wall or ceiling, with accessories with and including one additional 6 sqmm, PVC insulated, stranded copper conductor, FRLS-H, green colour for earth continuity conductor connected to common earth dolly including taking down old unserviceable sub main wiring of any type and making good the disturbed surface complete all as specified and as directed.(For Three Phase Supply) Notes-(i) Five runs of cable and one run of concealed conduct shall be measured as one unit. (ii) All chases will be cut by chase cutter only and surfaces shall be make good as per existing surfaces.

Material and labour for sub main wiring with two single core, 6 sqmm, FRLS-H, 1100 volts grade, ISI marked, with multistranded, PVC insulated unsheathed copper conductor cable, drawn in existing conduit with and including one additional 6 sqmm, PVC insulated, stranded copper conductor, FRLS-H, green colour for earth continuity conductor connected to common earth dolly including taking down old unserviceable sub main wiring of any type and making good the disturbed surface complete all as specified and as directed. Note- Three runs of cable shall be measured as one unit.

Material and labour for sub main wiring with two single core, 4 sqmm, FRLS-H, 1100 volts grade, ISI marked, with multistranded, PVC insulated unsheathed copper conductor cable, drawn in existing conduit with and including one additional 4 sqmm, PVC insulated, stranded copper conductor, FRLS-H, green colour for earth continuity conductor connected to common earth dolly including taking down old unserviceable sub main wiring of any type and making good the disturbed surface complete all as specified and as directed. Note- Three runs of cable shall be measured as one unit.

Material and labour for sub main wiring with two single core, 2.5 sqmm, FRLS-H, 1100 volts grade, ISI marked, with multistranded, PVC insulated unsheathed copper conductor cable, drawn in existing conduit with and including one additional 2.5 sqmm, PVC insulated, stranded copper conductor, FRLS-H, green colour for earth continuity conductor connected to common earth dolly including taking down old unserviceable sub main wiring of any type and making good the disturbed surface complete all as specified and as directed. Note- Three runs of cable shall be measured as one unit.

Supply and fixing of sheet metal enclosures for distribution board for MCCB's, TPN, Vertical, double door, 4 ways, 415 Volts with 200 Amps rated bus bar IP-43 protection, with shrouded neutral bar and insulated bus bar and earth link, suitable for MCCB 4 pole as incomer and MCBs as out going complete with making suitable size of MS cabinet 2mm thick dully grouted on the wall (flush) with opening arrangement including taking down the existing DB and MCBs/MCCB any type making connections with suitable size of lugs and making good the disturbed surface matching with existing surface complete all as specified and as directed. Note: MCCBs/MCBs shall be measured and paid separately.

Supply and fixing of sheet metal enclosures for distribution board for MCB's, TPN, Vertical, double door, 4 ways, 415 Volts with 200 Amps rated bus bar IP-42 protection, with shrouded neutral bar and insulated bus bar and earth link, suitable for MCB 4 pole as incomer and MCBs as out going complete with making suitable size of MS cabinet 2mm thick dully grouted on the wall (flush) with opening arrangement including taking down the existing DB and MCBs any type making connections with suitable size of lugs and making good the disturbed surface matching with existing surface complete all as specified and as directed. Note: MCCBs/MCBs shall be measured and paid separately.

Supply, installation, commissioning and testing of SPN distibution board, 12 way, double door, IP 43, conforming to IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles and taking down of old DB and MCB as existing complete all as specified and as directed.

Supply and fixing of MCCB, four pole, thermal magnetic release, adjustable type, 415 volts, 50 Hz, breaking capacity 25 kA, 125 Amps, complete all as specified and as directed.

Supply and fixing of MCB, four pole, 240 volts, 50Hz, breaking capacity 10kA, 'C' curve, 63 Amps, ISI marked complete all as specified and as directed.

Supply and fixing of MCB, four pole, 415 volts, 50Hz, breaking capacity 10kA, 'C' curve, 40 to 63 Amps, ISI marked complete all as specified and as directed.

Supply and fixing of MCB, single pole, 240 volts, 50Hz, breaking capacity 10kA, 'C' curve, 40 - 63 Amps, ISI marked complete all as specified and as directed.

Supply and fixing of MCB, single pole, 240 volts, 50Hz, breaking capacity 10kA, 'C' curve, 6-32 Amps, ISI marked complete all as specified and as directed.

Supply and fixing of MCB, single pole neutral, 240 volts, 50Hz, breaking capacity 10kA, 'C' curve, 40 - 63 Amps, ISI marked complete all as specified and as directed.

Disconnecting/dismantling old unserviceable earthing and material and labour for new earthing with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm GI wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire and thimbles protected by galvanized steel pipe 15mm dia (light grade) and connected to main switch or main control board all as shown in Electrical Plate No.3 of SSR Part-I & including necessary excavation and earth work in any type of strata, PCC (1:3:6) type C1 in pit, RCC cover slab 50mm thick in 1:2:4 type B-1 using 8mm dia TMT bars @10cm c/c both way with one 8mm dia bar as handle for lifting, 20mm dia GI medium grade watering pipe, funnel, wire wesh, charcoal or coke & salt in alternate layers, etc.all as indicated including testing on completion complete all as specified and directed. Note:- The new earthing shall be provided adjecent to old earthing site on the locations as directed by engineer in charge.

Supply and fixing ceiling fan, AC, Single phase, 230 V, 50Hz, 1200mm sweep with BLDC technology with maximum power input 35 W, 5 star BEE ratings complete alongwith all accessories as per OEM with and including down rod canpoy cover and 3 core PVC flexible cable for connections with all electrical connections, complete all as specified and directed.

Supply and fixing exhaust fan 300mm sweep metal body, heavy duty, with louvers 1400 RPM, 230 Volts with all acessories pre wired upto terminal block including connecting with 3 core copper conductor flexible cable from terminal box to the celing rose to connector of the light point including cutting holes in brick walls for fixing exhaust fans and making good the disturbed surfaces as per existing, complete all as specified and directed.

Material and labour for dismentaling and taking out old Geyser of any capacity, from wall surface and refixing the same after minor repair/ servicing including resistent PVC pipe 15mm dia not less than 60cm long suitable for incoming & outgoing connections of Geyser with washe complete with including fixing bolts/ fastener necessary PCC/ cement work for making good the disturbed surface, giving electric and water connection and testing after installation complete all as specified and directed.

Note:- Amount of credit of Rs. 29,441.00 for retrieved materials is mentioned in Schedule of Credit Page No. 15R of tender documents in pdf form which will be deducted offline while acceptance of tender.

S M BUILDERS

PARVEEN KUMAR

K.M CONSTRUCTIONS Co.

V K Constructive Builders

SM ENGINEERS

M/S JAISANT CONSTRUCTION CO.