Tender for The Creation of a Cabin for M/s. Balmer Lawrie (Flight Booking Office) at IIM Tiruchirappalli

Amount

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 66mm overall thickness Partition with 8mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg. / sq.cm cm including all necessary items and works etc. all complete as per standard specification.

Supplying and applying to finishing walls with Acrylic Smooth exterior paint of required shade, New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including required putty, priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc., all necessary items etc. all complete as per standard specification.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately): Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) 1.00 Sqm - 20 kg. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineering- charge. Pre-laminated particle board with decorative lamination on both sides cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-Charge. Polyester powder coated minimum thickness 50-micron aluminium tubular handle bar. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Size: 125x75x4 mm cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing 12 modular box necessary fittings (including power Switches, Sockets, cable, screw, pipes) etc completed as per standard specification and direction of Engineer in charge. Make: Legrand. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing wall mounting fan 16 inch with necessary fittings (Switch and socket), cable, screw, etc completed as per standard specification and direction of Engineer in charge. Make: Crompton for fan & Make: Legrand for Switches and Sockets. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing 4feet LED tube light with necessary fittings (including power switches, cable, screw, pipes) etc completed as per standard specification and direction of Engineer in charge. Make: Philips & Switches and Sockets Make: Legrand. cm including all necessary items and works etc. all complete as per standard specification.

Providing and fixing of 16 A switch and socket with necessary wiring and a Modular box, pipes etc., completed as per standard specification and direction of the Engineer in charge. Make: Legrand. cm including all necessary items and works etc. all complete as per standard specification.

GEES EPC SERVICES PVT. LTD. (BID ID -3259008)

SM ENTERPRISES (BID ID -3258276)