Loading…
Loading…
Tender Value
₹29.4 L
EMD Value
₹29,500
Closing Date
12 Jun 2026, 6:00 pm6d left
Ankleshwar nagarpalika chief officer
Street Light work in Nirantnagar at Ankleshwar.
311180
06 of 2026-2027
Open
Street Lighting
Bharuch
1 document required · 1 mandatory
₹1,500
Chief Officer, Ankleshwar Nagar Palika
₹29,500
4 Jun 2026
4 Jun 2026
4 Jun 2026
12 Jun 2026
4 Jun 2026
Name Of Work : Street Light work in Nirantnagar at Ankleshwar.
Sr.No. Item Description Quantity Total Rate Unit Amount
Supplying and erecting approved make Octagonal
pole made from HR sheet steel. The pole should be
made as per IS. and shall be coated with hot dip
galvanizing as per IS 2629/2633/4759, suitable
suspend local wind speed with integral Junction box
consist of terminal plate of min 6mm Hylam sheet,
standard profile 35mmX7.5mm Din-Rail for MCB
1 Mounting, stud type terminal and arrangement for 60.00 11411.99 Ea
cable termination to be erected With Suitable
foundation (Included) as per details given by
manufacturer considering site requirement. (E)
Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm
thickness with 225mmX225mmX16mm base plate,
4-M20 Bolts and 600mm long with necessary G.I. J
Bolts .Approx Pole weight 67 kg
Supplying, erecting, testing, commissioning approved
make M.S. Polygonal High Mast Pole having following
general Specification. (a) Polygonal Section fabricated
from M.S. Plate confirms BSEN 10025 & Hot deep
galvanized minimum 65/86 micron (as per IS
/1985) Lantern carriage with ring and rubber lines for
erection of luminaries of suitable site. (b) Maximum
telescopic section not more than four (c) Double drum
gear pipe motorized winch with 6mm dia S.S. Rod (For
16 mtr and above size) (d) Approved make L.E.D.
aviation light = 1 No. Lightening arrestor = 1 No. with
necessary wiring of 2.5 sq.mm 5 core ISI copper cable
Unarmoured. (e) Bottom most section suitable for
mounting reversible motor and switchgears having door
2 not more than 1400mm x 300mm with waterproof 4.00 141616.14 Ea
gasket & hinges & locking arrangement. (f) Pole
structure comprises suitable size of reversible motor,
cable and necessary switchgears with control panel. (g)
bottom section shall have suitable size of thickness
supports ribs foundation bolts nuts etc.(h) Item not
comprises the cost of lanterns. (i) Necessary Cement
Concrete foundation as per IS including testing &
commissioning of the entire structure for following size
of High Mast poles [1] High Mast 12 Mtr. TOP A/F
mm, BOTTOM A/F 360mm, No. of Sec. No. - 1, Bottom
Thickness - 3 mm, Size of Base Plate - Dia 520 mm x
mm thick, Foundation Bolt Size M24 x 850 mm, Qty -
Nos., Suitable for mounting Fitting of Light - 6 Nos.
(Suitable foundation (Included) as per details given by
Supplying and erecting street light pole bracket
comprising main B Class GI pipe of 4.2 cm/require
outside dia. complete with suitable B Class GI
sleeve tubing of approx. 45cms.length and suitable
for 76.5mm/80mm or require size pole top having
sufficient fastners for fixing the brackets and having
3 suitable rise as per site condition as directed and 60.00 795.88 Ea
spread of 2 mtr.with suitable welded stiffener
reducer and with lock nut complete painted with
one coat of Red oxide / PU base primer and two
coats of Aluminium / PU paint. Suitable for side
entry fitting brackets of following nos of arms. [a]
Single Arm bracket 2 Mtr
Sr.No. Item Description Quantity Total Rate Unit Amount
Supplying & erecting approved make SMC press
moulded composite FRP . loop-in, loopout approx.
2mm thick box complete with Bakelite connector
strip 5way(3P+N+E),DIN rail for mounting mob &
4 hinged doors as per requirement having locking 60.00 898.90 Ea
arrangements with mounting clamp with nuts, bolts
& washers suitable for erection on pole with cable
clamps& earth bolt of following size of box.(a)
300mm x 200mm x 100mm [deep]
Providing and erecting iron clad cable route marker
duly marked with ELE.CABLE of size 23 cm.X 12 cm.
Flushed with ground in cement foundation as
directed by Engineer in charge.
Supplying and erecting LED street light / Flood light
fittings with High power White LEDs wattage of
1Watt and above assembled on single MCPCB,
efficiency more than 130 lm/w and corrosion free
High pressure die cast aluminum housing with
smooth finish powder coated and heat sink
extruded aluminium with diffuser and
Polycarbonate optics/ lenses with company
mark/name engraved or embossed 120 to
V,Power Factor more than 0.95, THD < 10 %, CCT
3000 K to 5700K, Uniformity ratio >0.45, Luminaire
6 efficacy> 100 lumens/watt . LED driver efficiency > 60.00 5976.17 Ea
85 %.CREE /OSRAM / PHILIPS Lumileds / NICHIA /
SEOUL/ BridgeLux (U.S.A.) make LED used for
luminaire. ( fittings required LM-79 & LM-80
certificates)(NOTE: Below description have shown
ranges of Wattage capacity of LED fittings.The
Engineer incharge may select any wattage capacity
between the ranges shown.) (A) Street Light (IP-65),
Surge protection - 4KV integral and 10 kv non
integral ,Light must have 440VAC line supply
protection. It should withstand 48 hours for
440VAC line supply.(iii) Above 60 to 90 watts Cat-lll
Supplying and erecting LED street light / Flood light
fittings with High power White LEDs wattage of
Watt and above assembled on single MCPCB,
efficiency more than 130 lm/w and corrosion free
High pressure die cast aluminum housing with
smooth finish powder coated and heat sink
extruded aluminium with diffuser and
Polycarbonate optics/ lenses, with toughened glass
with company mark/name engraved or embossed
160 to 270 V,Power Factor more than 0.95, THD <
10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,
Luminaire efficacy> 100 lumens/watt . LED driver
efficiency > 85 %.( fittings required LM-79 & LM-80
certificates)(NOTE: Below description have shown
ranges of Wattage capacity of LED fittings.The
Engineer incharge may select any wattage capacity
between the ranges shown.) (B) Flood Light (IP-65),
Surge protection -4KV integral and ,Light must have
440VAC line supply with over-voltage protection.
(vii) above 200 to 250 watts Cat-lll
Sr.No. Item Description Quantity Total Rate Unit Amount
Supplying & erecting approved make Digital time
switch having lithium cell 6 years operative and
operate battery backup 1 channel day clock with
memory programme, suitable to operate on 240V +
5%, 16A with, floating contacts Minimum switching
8 setup time 1 minimum & LCD display. Also 2.00 3168.37 Ea
comprised permanent ON/OFF switching.
Programming switches & housed in fire proof
thermoplastic enclosure & transparent cover
erected as required with necessary connection
erected as directed.(For high mast and street lights)
Supply of Fibreglass Platform Step (A Type) Ladder -
18 FT having following specifications : It should
have large fully serrated platform 15” wide 20”
9 deep which locks ladder , Aluminium feet with thick 1.00 33895.60 Ea
rubber tread, top rail guard to serve as a railing,
two pairs of gusset support at the bottom step and
All gussets are heavy duty steel. Capacity : 300 lbs.
Supplying & erecting IP 55 grade following size
section pillar fabricated from joint less M.S. Sheet
with angle iron legs made from jointless M.S. Angle
with cable clamps to be buried in ground to have
appropriate erection to work uniform until erected
with cement concrete foundation and 45 cm high
bricks work finishing with plaster etc. hinged double
door internally supported on both side,with internal
and outside looking arrangement with look and
10 keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two 2.00 1884.66 Ea
Nos. one is welded and other with nut and bolt for
erecting Bakelite sheet. Painting the Section Pillar
inside and out side with three tank powder coated
paint. section pillar roof should be without joint
with water leakage proof & tested as per IP 55 test
& followed by IS 2147 of 1962 (C) 60 X 30 X 45 cm
section pillar fabricated from 16 Gauge MS Sheet
with angle iron legs 45 cm long made from 35 X
X 5 mm thick MS angle. (For high mast and street
Providing and erecting Sheet Steel powder coated
MCB distribution board - flush / surface mounted
fitted with busbar, neutral link, earth bar and DIN
rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &
without MCB to house appropriate nos. of
MCBs.(The DBs should be used of same company of
MCB to be used) suitable for (B) three phase
incoming and single phase horizontal type outgoing
Per phase isolation type (PPI) (b) sheet steel double
Providing and erecting Approved make Four pole
moulded case circuit breaker having breaking
capacity ICU of 25 KA. at 415 V,having normal
current rating up to 25 A to 100A. with Fixed
12 thermal & magnetic release suitable to work on 2.00 6173.12 Ea
A.C. supply 50 c/s. with all internal connections,
spreader tinned copper & complete erected in
existing 16 G.M.S. housing. ICS=100% of ICU only
Cat III (100A FP MCCB incomer)
Providing Approved make Triple Pole Metal Clad
Switch Fuse Unit 415/500 V. with HRC fuse of
suitable load and neutral link confirming to IS
(a)200 A Cat.III
Providing & erecting 415 V MCB Four Pole for
Motor & Inductive Load (C Curve) having 10KA
breaking capacity & confirms to IS :8828 in existing
box having following capacity (b)40 Amp. Cat.III
Sr.No. Item Description Quantity Total Rate Unit Amount
Providing & erecting 240 V MCB double pole switch
for lighting Load (B Curve) having 10 KA breaking
capacity & confirms to IS : 8828 in existing box having
following capacity (B) 40 Amp. Cat.III
providing and erecting Miniature circuit breaker
single pole 0.5A to 2A system and having breaking
capacity 10 KA to be erected in existing box.
confirming to IS 8828/1996 with ISI Mark Cat.III
Providing and erecting busbar chamber confirming
to IS-375 fabricated from 16 G.M.S. sheet, dust &
vermin proof having hinged door with rubber
gasket and necessary busbar supports with
Aluminium busbar having current density not more
than 0.8 Amp. / sq.mm (Rated current / cross
section area) duly wrapped with colour insulation
tape for phase sequence, three phase & neutral
each Suitable for following current capacity with
necessary painting mounted on wall or pedestal
frame of required size with necessary connections.
(B) Suitable for 200 Amp. Capacity
Supplying and erecting triple pole & neutral 440V/
500V panel mounting Aluminium Busbars with four
equal Nos. of bus having current density not more
than 0.8 Amp. / sq.mm (Rated current / cross
section area) duly wrapped with colour insulating
18 tape for phase sequence of following current 2.00 660.54 Rn.Mtr
carrying capacity, erected with necessary bus bar
supports /insulators, main cable socket to each
busbar,erected in existing cubical panel with
necessary connections. (A) Suitable for 100 Amp.
Providing & erecting High Voltage Danger Notice
19 Board sticker as per language suggested by 2.00 35.35 Ea
engineer incharge of standard size-as per IS
Providing and erecting XLPE(IS:7098)(I)-88 ISI
armoured cable multistrand / Solid Copper
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe at
road crossing or floor of following size of cables.
(C) 4 core 6 Sq. mm
Providing and, fixing heavy duty flange type brass
cable gland with rubber ring for PVC insulated
21 armoured cable complete with out going tails, 68.00 38.38 Ea
insulating tape etc for following size of cables. (B)
to 4 core 6 Sq. mm
Solder less crimping type Copper lugs conforming
to IS suitable for cable of following size evenly
22 crimped with high pressure tool & connected to 272.00 8.08 Ea
switchgear terminals with brass/cadmium plated
nut bolts in an approved manner. (A) 1.5/2.5 to
Supplying and erecting Flexible PVC insulated multi
strand multi core 1.1 kv grade ISI marked copper
wires of following size to be erected as directed. (h)
2.50 Sq.mm 3 core round PVC sheathed
Sr.No. Item Description Quantity Total Rate Unit Amount
Supplying & erecting earth pit of minimum bore
dia.150mm size approved make Earthing Electrode
consisting Pipe-in-Pipe Technology as per IS 3043-
1987 made of corrosion free hot dipped G.I.Pipes
having Outer pipe dia of 50mm having 80-200
Micron galvanising, Inner pipe dia of 25 mm having
200- 250 Micron galvanising, connection terminal
dia of 12mm with constant ohmic value surrounded
by highly conductive compound with high charge
dissipation suitable for following type of
applications with chamber and heavy duty
cover.(approved make OEM has to submit test
certificate) & having back filling compound of (B)
24 Inner chemical (CCM Compound)- Resistivity:- 0.2 • 6.00 5760.03 Ea
/ meter testing as per IEC 62561-2017, Voltage
drop:- < 1 volt at no load & dry form, Sulphar
content:- <2%(C) Back fill Compound :- Earthing
compound should be capable to retainmoisture for
long time Necessary test report must be
submitted.(c) For Electrical Installation covering
Transformer Neutrals, Lightning arrester Earthing,
A.C.Plant & Sensitive Computer System(like
Automation, SCADA) i.e independent (b)For
Electrical installation up to 11 KV in normal soil.
Length of Pipe : 2.00 mtrs Back filling Compound :1
no. Bag of 25 Kg
Providing and erecting Pipe type earthing having
150 cms.long and 2.5 cms. dia. galvanised iron pipe
25 with coupling and buch buried in specially prepared 64.00 368.65 Ea
earth pit complete with necessary 8 SWG earth
wire. - to be used for each Street Light
For using salt and charcoal / coke as required for
pipe type earthing.
Providing pair of rubber hand gloves suitable for
working on 11 KV/22 KV supply.
I / we agree to carry out the above work at __________% above the estimated rate put to tender
I / we agree to carry out the above work at __________% below the estimated rate put to tender.
Estimated amount Estimated amount
Put to tender Rs. 29,41,722.00 Put to tender Rs.
Net amount Rs.___________________ Net amount Rs.______________________
Contractor Sign With Seal Ankleshwar Nagar Palika
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
Nirant nagar Street Light.pdf
01 Schedule-B.pdf
Download all tender documents and submit your bid